Numark Industries CDN-22MK III User's Manual
Contents
1. b Connect the remote control connection cable from the Unit 1 connector on the main unit to the Unit 1 connector on the remote control unit Repeat for Unit 2 c The output connection cords and the remote control connection cables are supplied with the main unit Be sure to use the remote control connection cables which have been supplied Use of another cable type might cause damage FADER MIXER START e AUTO START CABLE d Connect Relay or Fader start cables For fader start attach both side of your CD play to a similarly equipped DJ mixer as in the top drawing For relay capability take the auto start cable and connect the two jacks in the rear of your CD player EE 15 MOUNTING YOUR CD PLAYER e Mount the units in your console or rack with 19 EIA rails f The transport should be mounted not to exceed an angle of 15 degrees g Your CD player can be affected by excess vibration so mount the units TRANSPORT in a secure environment if possible Numark The Leader in DJ Technology 2002 Numark Industries 7 http www numark com CDN 22MK IIl DESCRIPTION CDN 22S REMOTE FEATURES O Q PROFESSIONAL CD PLAYER 2 O Q 1 PROGRAM Depress this button and the unit will stop and the program indicator will light Select each track to be programmed and press the PROGRAM button between selections You can progra2. 5 Press play on CD1 of the unit When that CD1 has finished play it will send a signal to CD2 to start play You will see CD2 start play and CD1 pause and cue to the beginning of the next track When CD2 has completed play CD1 will start Note The play command is sent at the end of specified play If the unit is in SINGLE mode the play command will start at the end of the track If the unit is in CONTINUOUS mode the play command will be sent at the end of the full CD Two CDs will play continuously alternating from side to side This feature will also work in program mode however if the sides are also in SINGLE mode the same number of tracks programmed should be the same Play will stop at the end of the last track FADER START MODE This mode is achievable by attaching both sides of your CD player to a similarly equipped DJ mixer 1 Connect cables between the CD remote unit and your DJ mixer 2 Hold down the time button for 1 2 seconds to activate the fader start capability 3 Follow the directions in your mixer manual Typically if you move the crossfader toward the active channel the attached CD player will activate When it is moved away that side will cue similar to pressing the cue button Numark The Leader in DJ Technology 2002 Numark Industries 12 http www numark com EXAMPLE OF MIXING USING BOTH PLAYERS OF YOUR CD PLAYER While playing a disc on PLAYER 1 load a disc into PLAYER 2 and select your next track matc
3. Numark Professional Disc Jockey Products CDN 22MK II PROFESSIONAL DUAL CD PLAYER OPERATING MANUAL 2002 Numark Industries http www numark com CDN 22MK IIl Safety Information and Product Registration CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying this appliance CAUTION FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before this product is connected and used 2 Retain Instructions The safety and operating instructions should be kept for future reference 3 He
4. ation location vibrations or physical shock The disc is too dirty Clean the disc Programmed disc play will not function The CD player is in normal disk play mode Hold down the Program button for 3 seconds then program the tracks Hum Loose cable connections Firmly connect all audio plugs Numark The Leader in DJ Technology 2002 Numark Industries 14 http www numark com CDN 22MK lll SPECIFICATIONS TECHNICAL Quantization 16 bit linear channel 3 beam laser Oversampling rate 8 times Frequency response 20Hz 20KHz Channel separation 86dB T H D NOISE 0 01 S N ratio IHF A 94dB Output level 2 0Vrms Short access time Play next track less than 1 7sec Long access time Track 1 gt Track 20 less than 3sec Start Time less than 0 3 sec Pitch control range 12 Pitch bend 16 Digital Output type 2 form 1 S PDIF Sony Phillips Digital Interface Format GENERAL Dimensions Main Unit 482 W x 88 8 x 264 D mm without feet 19 W x 3 5 H x 10 3 8 D inches without feet Control Unit 482 W x 88 8 H x 75 D mm without feet 19 W x 3 1 2 H x 2 7 8 D inches without feet Weight Player Unit 5 Kgs 11 Ibs Control Unit 2 Kgs 4 4 Ibs Power Supply 115 230V AC 50 60Hz Power Consumption 25W Numark The Leader in DJ Technology 2002 Numark Industries 15 http www numark com
5. ayer to the Cue point by pressing Cue cue point PLAYER 2 PLAYER 2 MIXER PITGH CRO s With a matching downbeat from Player 1 press the play button If you are beat mixing turn on your Pitch adjust and follow the directions for beat matching Numark The Leader in DJ Technology 13 When you are happy with you mix adjust you mixer accordingly http www numark com CDN 22MK iii BEFORE SWITCHING OFF THE POWER When you have finished using the CD player be sure that the disc tray is closed with the OPEN CLOSE button before switching off the power DO NOT switch off the power when the disc holder is open TROUBLESHOOTING Switch off the power after the disc holder has been closed with the OPEN CLOSE button Symptom Possible Cause Corrective Action The power fails to switch on when the POWER switch is set to on Poor power plug connection at the AC outlet Insert the power plug firmly into the AC outlet and make sure connection is good in unit rear Disc play does not start The disc is loaded upside down The disc is too dirty Reload the disc with the label side up Clean the disc No sound Improper output cable Connect the output cables connections correctly Improper amplifier operation Check amplifier setup Sound skips The CD player is subject to Change the install
6. e it to the desired position By pressing PLAY PAUSE then CUE you can confirm that this CUE POINT new cue point is desirable Position on the disc Back cue operation Numark The Leader in DJ Technology 2002 Numark Industries 10 http www numark com CDN 22MK III MATCHING THE BEATS PER MINUTE BPM Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear and adjusting the pitch When the tempo of the music of the selected CD player is slow compared to the tempo of the other player move the slider to the side and match the tempo When faster move the pitch slider to the side The following description is for the case of matching the pitch of PLAYER 2 to the pitch of the music being played on PLAYER 1 x op G2 X IC ee 2 gt 2 TC A 2 29 ER Press PLAY PAUSE to start PLAYER 1 Press PLAY PAUSE to start PLAYER 2 PLAYER 1 is playing Both CD players are playing discs 25 B t eer te iC 99 xen to PLAYER 2j in your headphones n dit When PLAYER 2 is fast compared to PLAYER 1 slow down PLAYER 2 When PLAYER 2 is slow compared to PLAYER 1 speed up PLAYER 2 Timm Timm BEAT MATCHING USING PITCH BEND If you find the BPM s Beats Per Minute or Tempos are the same however the drum beats are not matched you will need t
7. ed Warnings All warnings on this product and in these operating instructions should be followed 4 Follow Instructions All operating and other instructions should be followed 5 Water and Moisture This product should be kept away from E direct contact with liquids 6 Heat Avoid placing this product to close to any high heat sources such as radiators 7 Ventilation The appliance should be situated so that it s location or position does not interfere with it s proper ventilation For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation opening or placed in a built installation such as bookcase or cabinet that may impede the flow of air through the ventilation openings 8 Power Sources This product should be connected to a power supply only of the type described in these operating instructions or as marked on the unit 9 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord 10 Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer 11 Cleaning The appliance should be cleaned only as recommended by the manufacture
8. h its pitch to the track playing on PLAYER1 and when you are ready use the crossfader on your mixer to fade from PLAYER 1 to PLAYER 2 Load a disc in PLAYER 1 and select the track and press PLAY Load a disc in PLAYER 2 and select the track then play Set and edit a start cue point on PLAYER 2 Check you new cue point Do a MIX 2002 Numark Industries CDN 22MK iii PLAYER 1 PLAYER 1 PLAYER 1 SEE TRACK oF gt Load disc and press the Select the track to be Press the PLAY button OPEN CLOSE button played PLAYER 2 PLAYER 2 PLAYER 2 TRACK gt aig Uf Ey oF Load a disc and press the Select the track to be Press the PLAY button OPEN CLOSE button played PLAYER 2 PLAYER 2 PLAYER 2 gt Press the Pause button of Rapidly search for a cue Slowly set the right point using the inner wheel PLAYER 2 point using the outer wheel PLAYER 2 PLAYER 2 PLAYER 2 fa Listen with the monitor and press the play button Press the cue button then play to be sure of the set Set the pl
9. m up to 30 tracks Press PLAY to start the program To exit and erase program hold the program button down for more than 2 seconds while the unit is stopped open the disc tray or turn off the power 2 CONT SING Will cause just a single track to play or all tracks in order by pressing once or twice 3 LCD DISPLAY Indicates all the functions as they are occurring with the CD These functions are explained in the next section 4 TIME Time Button The TIME button switches the time display between elapsed playing time and remaining time on the track Holding for more than one second activates auto start functions 5 OPEN CLOSE Disc Tray Open Close Press to load or eject the disc Each press will open or close the disc tray on the transport NOTE Tray will not open unless the disc has been paused 6 TRACK Track Buttons These buttons are used to select the track to be played 7 Track 10 Button This button is for quickly advancing to higher tracks on a CD 8 PITCH Pitch Button This button activates the Pitch Slider 14 9 PITCH BEND Pitch Bend Button When each of the two CD players is playing a CD the pitch bend function allows the positioning of the bass beats to be matched after the pitch of each disc is matched Either player can catch up or fall back to match the other player The pitch will automatically rise while the button is pressed allowing catch up and return to the o
10. nd thank you for making the CDN 22 your choice in professional CD players FEATURES e Interactive pitch wheel adjustment e Fader relay start e Digital Output e speed scanning e Frame search e Auto cue e 10 tracks skip search e 30 tracks program play e Pitch display e 8 times oversampling e 8 cm single CD compatible Numark The Leader in DJ Technology 2002 Numark Industries 4 http www numark com CDN 22MK iii TABLE OF CONTENTS Safety and Registration 2 Introduction 4 Set up Instructions amp Connections 7 Description of the Features Remote Control Unit 8 Display 9 Transport 9 Basic Operation Play Pause and Cue Operations 10 Matching the Tempo 11 Beat Matching Using Pitch Bend 11 Relay and Fader Start 12 Example of Mixing 13 Before Switching off the Power 14 Troubleshooting Guide 14 Information and Specifications 15 Numark The Leader in DJ Technology 2002 Numark Industries 5 http www numark com CDN 22MK IIl CHECK TO BE SURE THE FOLLOWING ITEMS ARE IN THIS BOX 1 DUAL TRANSPORT PLAYER UNIT 1 REMOTE CONTROL UNIT 1 OWNERS MANUAL THIS BOOKLET 2 RCA CONNECTING CABLES 2 CONTROL CABLES 1 FADER START CABLE Numark The Leader in DJ Technology 62 2002 Numark Industries http www numark com CDN 22MK lll CONNECTIONS Typical connection with a mixer is illustrated right a Connect the output connection cords from the CD Player to the line inputs of your mixer
11. o temporarily change the pitch This description is for the case of matching the beat of PLAYER 2 to the beat of the music being played on PLAYER 1 This procedure can be done on either PLAYER After matching the BPM s adjust the pitch temporarily as follows When PLAYER 2 is ahead press the L When PLAYER 2 is behind press the or rotate the jog wheel counter clockwise or rotate the jog wheel clockwise PITCH BEND PITCH BEND or XJ or Q O The pitch changes automatically while the or L button is being pressed or the jog wheel is rotated The faster you rotate the wheel the more you change Releasing the button or wheel results in a return to the original pitch So the BPM s are once again the same Numark The Leader in DJ Technology 2002 Numark Industries 11 http www numark com CDN 22MK IIl RELAY PLAY The cables required are commercially available 3 5mm 1 8 mini plug cables One has already been included with your unit so the relay function could be used 1 Connect auto start cable between both sides of the remote unit TIME 2 Insert CDs into both sides of the unit ur es o 90 CC IE 3 Hold down the time buttons for 1 2 seconds until the display P _ f indicates auto and the track number begins to flash The track B number will flash while the mode is active Both sides must be LN active for relay to work 4 Put both sides in SINGLE play mode while learning this function
12. pending on mode setting Numark The Leader in DJ Technology 2002 Numark Industries 9 http www numark com CDN 22MK lll DESCRIPTION OF THE PLAY PAUSE AND CUE OPERATIONS Press the Press the PLAY and CUE PLAY PAUSE button CUE button Position on the disc Play interval Back cue operation Pressing the PLAY PAUSE button starts the disc Pressing the CUE button will reset the disc to the last place where the disc was started This is called the cue point By alternately pressing the PLAY PAUSE button and the CUE button the disc may be returned and played from the cue point any number of times This function is called back cue PLAY PAUSE and CUE Press the Press the Press the PLAY PAUSE button PLAY PAUSE button CUE button Position on the disc gt ll gt Play interval Play interv When play has been paused and then started again the return position for the back cue will be updated to this new position Back cue operation EDITING CUE POINT M fa N When the inner search dial is turned 8 Press the while a cue point is set a new cue P CUE button point can be located The CD player will repeatedly play small parts of the CD as you mov
13. r 12 Non use Periods The power cord of the appliance should be unplugged from the outlet when left unused for long periods of time 13 Damage Requiring Service Only qualified personnel should service this product If you have any questions about Service please contact Numark at the number s shown on the back cover of this manual 14 Grounding or Polarization Precautions should be taken so that the grounding or polarization means built into the CD player is not defeated 15 Internal External Voltage Selectors Internal or external voltage selector switches if any should only be reset and re equipped with a proper plug for alternative voltage by a qualified service technician Do not attempt to alter this yourself Numark The Leader in DJ Technology 2002 Numark Industries http www numark com WARNING To reduce the risk of fire or electrical shock do not expose this appliance to rain or moisture Electrical equipment should NEVER be kept or stored in damp environments DANGER INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED AVOID DIRECT EXPOSURE TO BEAM CAUTION This product utilizes a laser Use of controls or adjustments other than those specified herein may result in hazardous radiation exposure SERVICE INSTRUCTIONS Disconnect power cord before servicing Replace critical components only with factory parts or recommended equivalents For AC line powered
14. riginal pitch when the button is released The pitch will automatically drop while the 10 12 button is pressed allowing fall back and return to the original pitch when the button is released By changing the pitch of one disc with respect to the other in this way the beats can be matched SEARCH WHEEL OUTER RING This wheel has 3 forward and 3 reverse speed positions for searching through songs The more you turn the wheel in either direction the faster you search through the music JOG WHEEL INNER RING This jog wheel serves 2 functions depending on the current mode a The jog wheel will act as a slow frame search control when the CD is not playing but either paused or set to a cue point To set a new frame cue point spin the wheel then press play when you have determined the proper position Press CUE to return to the CUE POINT b The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to speed up or counterclockwise to slow down CUE Pressing the CUE button during play provides a return to the position at which play was started If PAUSE is used before CUE that will become the cue point Alternately pressing the PLAY button and the CUE button allows the CD to be played from the same position any number of times The CUE LED will light up from the time the CUE button is pressed until the CD has reset to the position at which play wa
15. s started Steady lighting of this LED indicates the ready condition START PAUSE Play Pause Button Each press of the Play Pause Button causes the operation to change from play to pause or from pause to play PITCH SLIDER The pitch can be changed up 1296 by pressing the PITCH button so the PITCH LED is lit then moving the sliding fader The pitch will not be changed if the PITCH LED is off Numark The Leader in DJ Technology 2002 Numark Industries 8 http www numark com CDN 22MK IIl LCD DISPLAY FEATURES 11 12 13 CUE PROGRAM d am TRANSPORT FEATURES H H H H 19 DISC TRAY Place your CD in here 20 OPEN CLOSE Disc Tray Open Close Press to load or eject the disc Each press will open or close the disc tray on the transport NOTE Tray will not open unless the disc has been paused 21 POWER BUTTON Turn on and turn off the machine from this button The unit should always be shut down with this button first before any external power is removed 22 RCA AUDIO JACKS Connect your CD player to your mixer from this line level output PLAY Active while the unit is actually playing a CD PAUSE Active when the unit is paused CUE Flashing when the unit is setting a cue point Lit continuously when the unit is paused at a cue point PROGRAM Used for preprogramming
16. the track order to automatically be played by the unit This is a great function if you need to leave the CD player 23 VOLTAGE SELECTOR Set this switch to the alone voltage for your location TIME MODE 24 POWER CONNECTOR Plug your power supplied power cord into here then plug unit into a power outlet ne ay ven one 25 CONTROL CONNECTOR Plug your control cables particular track This function is controlled by the f E d A TIME BUTTON 4 pod unit into SINGLE Shows when the unit is set to play just 26 DIGITAL OUTPUTS The format is type 2 form 1 ong ata ume Ven MS ine CD also known as S PDIF Sony Phillips Digital Interface play continuously through all tracks This function is Format controlled by the SING CONT BUTTON 2 PITCH Is lit when the PITCH BUTTON is active TIME BAR Shows either time remaining or elapsed depending on the setting of the TIME BUTTON 4 PITCH Shows the percentage change in pitch Elapsed is for showing time as it is taking place TRACK Shows the track that the unit is playing with MINUTES Shows the minutes elapsed Numark or remaining depending on mode dE setting 4 SECONDS Shows the seconds PRESE covez elapsed or remaining depending on O mode setting 49 2 FRAMES The CD Player breaks down 3 695 C a second into 75 frames for accurate cueing This shows the frames elapsed or remaining de
17. units Before returning repaired unit to user use an ohmmeter to measure from both AC plug blades to all exposed metallic parts The resistance should be no more than 100 0000hms CDN 22MK Ill NOTICE CONCERNING FCC REGULATIONS This equipment generates and uses radio frequency energy and may cause interference to radio and television reception if you do not operate it in strict accordance with the procedures detailed in this OPERATING MANUAL This unit complies with Class B computing device rules in accordance with the specifications in Sub part J or Part 15 of the FCC Rules which are designed to provide reasonable protection against such interference in a residential installation There is no guarantee however that interference will not occur in a particular installation If the unit does cause interference to any radio or television reception try to reduce it by one or more of the following means a Reposition the other unit and or its antennae b Move this unit c Move this unit and the other unit s further apart d Plug this unit into a different AC outlet so that it is on a different circuit from the other equipment This note is in accordance with Section 15 838 of the FCC Rules This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications DOUBLE INSULATED When servicing
18. use only identical replacement parts For 220 volt use in USA use NEMA style 220 volt plug For other countries use proper plug for local outlet LINE VOLTAGE SELECTION 1 The desired voltage may be set with the VOLTAGE SELECTOR switch on the rear panel of the main unit using a screw driver 2 Do not twist the VOLTAGE SELECTOR switch with excessive force as this may cause damage 230V 3 If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit Retain this information and your original purchase receipt for your records Please return the enclosed warranty card to register your CD player with us MODEL SERIAL NUMBER PURCHASED FROM DATE OF PURCHASE Numark The Leader in DJ Technology 2002 Numark Industries 3 http www numark com CDN 22MK IIl Numark CDN 22MK lll PROFESSIONAL DUAL TRANSPORT CD PLAYER WITH REMOTE CONTROLLER CONGRATULATIONS You have just purchased a dual CD player designed specifically for the professional DJ This unit has been designed to provide CD mixing with the same ease and creativity that you have enjoyed with records Please take a few moments to familiarize yourself with the CDN 22 by reading the following information before attempting to operate the unit Once again congratulations a
Download Pdf Manuals
Related Search