Northern Industrial Tools 112020 User's Manual
Contents
1. AIR PALM NAILER USER S MANUAL Read carefully and understand RULES FOR SAFE OPERATION and instructions before operating Failure to follow the safety rules and other basic safety precautions may result in serious personal injury ITEM 112020 For technical questions and replacement parts please call 1 800 222 5381 Thank you very much for choosinga NORTHERN TOOL EQUIPMENT CO INC Product For future reference please complete the owner s record below Model Purchase Date Save the receipt warranty and theseinstructions It isimportant that youread the entire manual to become familiar with this product before you begin using it This machine isdesigned for certainapplications only Northern Tool Equipment strongly recommends that this machine is notmodified and or used for any applicationother than that for whichit was designed If you haveany questions relativeto a particular application DO NOT use the machine until you have first contacted Northern Tool Equipmentto determine if itcan or shouldbe performed onthe product Before using thisproduct please readthe following instructions carefully DESCRIPTION amp INTENDED USE The Northern Industrial Air Palm Sander features an advanced design with a compact structure superior technology and substantial attack strength This model is safe and reliable to operate while driving nailsinto the workpieces without a trigger Ideal for nailing in tig2. 13 andis steady 10 Remove the hand that is holding the nail and continue pushingthe tool todrive the fastener into place TROUBLE SHOOTING Symptom Problems Solution Air Leaking Worn O ring orloose screw Replace O ring ortighten screw Adjust air pressure to the specified range Replace O ring Air pressure isnot in specifiedrange Attack strength notenough The O ring besideslip set isworn No nail fires when connected Insufficient air supply Adjust air pressure air pressure Worn O ring Check and replace O ring INSPECTION MAINTENANCE AND CLEANING Always disconnect the pneumatic tool fromits compressed airsupply before performing any inspection maintenance adjustments or cleaning Place 5 7 dropsof pneumatic tooloil into the air inlet beforeeach work dayor after 2hours of continuous use Clean daily witha clean clothto remove alldirt oil andgrease from the pneumatic tool If necessary you may usea mild detergent Do not usesolvents as damageto the pneumatic tool may occur Do notimmerse the pneumatictool in any liquids 3 of 4 PARTS DIAGRAM L No Description No Description No Description 1 Bolt M5x20 9 Cylinder 17 Gun Body 2 Cylinder Cover 10 Cylinder Cover 18 Air Inlet Plug 3 O ring 53 5x2 6 11 O ring 43x2 65 19 Washer 4 Washer 12 Piston 20 Spring 5 Sealing Washer 13 Ram Pin 21 Fix Set 6 O ring 14 O ring 61 4x2 6 22
3. in the hands of untrained users Maintain pneumatic tools Before each usecheck for misalignmentor binding of moving parts breakage of parts damagedair hose andany other conditionthat may affect the pneumatic tools operation Ifdamaged have the tool repaired before use Many accidents are caused by poorly maintained pneumatic tools Keep handle dry clean andfree from oiland grease Make sure the hose is free of obstructions orsnags Entangled hoses cancause loss of balance orfooting 2 of 4 OPERATINGINSTRUCTION 1 Make surethe tool isdisconnected from theair hose 2 Wear appropriate eye earand other safety equipment 3 Place 5 7 drops of lubricationinto the airinlet before use and clean the pneumatic tool after each use 4 Check forsmooth and proper operation of the nosepiece Do notuse the toolif the nose assembly is notfunctioning or isrestrained 5 Keep toolpointed away fromyourself and others 6 Connect airhose using onlyclean dry regulated compressedair at 70 100PSI 7 Check for audible leaks aroundvalves and gaskets Never use atool that leaksor has damaged parts 8 Keep tool pointed in asafe direction whenloading nails Holdthe nail inthe same manner as if youwere using acommon hammer With the otherhand place thetool in astraight line with the directionin which youintend to drivethe nail 9 Place thefix set 21 around the nailhead and gently push the tooluntil the nailhead comes into contactwith the rampin
4. Magnet Slip Set 15 Bumper 23 Bolt 8 Sealing Ring 16 Axle sleeve 4of4 A WARNING Some dust createdby power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of Californiato cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica frombricks and cementand other masonry products and arsenicand chromium from chemically treatedlumber Yourrisk from these exposures varies dependingon how often you do thistype of work To reduce your exposureto these chemicals work in awell ventilated area and work with approved safety equipment such as those dust masks thatare specially designedto filter out microscopic particles Northern Tool Equipment Co 2800 Southcross Drive West P O Box 1499 Burnsville MN 5337 0499 Made in China
5. are tiredor under theinfluence of drugs alcoholor medication Amoment of inattention while operating pneumatictools may result inserious personal injury Dress properly Do notwear loose clothing of jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long haircan be caughtin moving parts Air vents often cover moving parts and should be avoided Always use the appropriate eye andear protection and other safety equipment Safety equipment such as dust mask non skid safety shoes and a hardhatused for appropriate conditions willreduce personal injuries Avoid accidental starting Disconnect tool from air supply when not inuse and when carrying toolto another workarea Do not overreach Keep proper footingand balance atall times This enables better control of the pneumatic tool inunexpected situations TOOL USE AND CARE Never use bottled gas such asoxygen or any other combustible gases as a pneumatic source forthis tool Danger of explosionand serious personalinjury may result Do not connect pneumatic tool tocompressed air inwhich the pressureexceeds 120 PSI Use air hosesrated for safe operation of thetool Air hosesrated for amaximum of 150 PSI orgreater must beused with thistool Do not forcethe pneumatic tooland use thetool only forits intended use Do not discharge fasteners intoopen air concrete stone hardwoods knots or any material too hard forthe fastener to penetrate Do notuse the b
6. ht corners toe nailing joist hangerinstallations and more TECHNICAL SPECIFICATIONS Item Description Capacity 1 Piece Nail length Up to 4 3 4 Inches Nail diameter 5d to 70d Operation pressure 70 100 PSI Air inlet 1 4 NPT Dimension 4 x 3 x5 Weight 2 Ibs GENERAL SAFETY RULES A WARNING Read and understandall instructions Failureto follow allinstructions listed below may result in electric shock fire and or serious injury A WARNING The warnings cautions and instructions discussedin this instruction manual cannot coverall possible conditions or situations thatcould occur It must be understood by the operator that commonsense and cautionare factors whichcannot be built into this product but mustbe supplied bythe operator SAVE THESE INSTRUCTIONS WORK AREA Keep work area clean and welllit Cluttered and dark work areas can cause accidents Do not useyour pneumatic tool where there isa risk of causing a fireor an explosion e g in the presence of flammable liquids gasses ordust Pneumatic tools can create sparks which mayignite the dustor fumes Keep children and bystanders away while operating a pneumatic tool Distractions can cause youto lose control so visitors shouldremain at asafe distance fromthe work area 1 of 4 PERSONAL SAFETY Stay alert watch what you are doing and usecommon sense when operating a pneumatic tool Donot use a pneumatic tool while you
7. ody of the toolor top capas a hammer Discharged fasteners may cause injury Do not drive fasteners near edge of material The workpiece may split causing the fastener to ricochet Be aware thenail may followthe grain ofthe wood causingit to protrude unexpectedly fromthe side ofthe work material Do not drivenails blindly into walls floors orother work areas Fasteners driven into live electrical wires plumbing or othertypes of obstructionscan result ininjury Be aware thatnails can bedriven completely throughthing or verysoft work material Make sure the pressure in the compressor is suchthat nails are set into the material and notpushed completely through Do not drivenails onto theheads of otherfasteners Strong recoil jammedfasteners or ricocheted nails may result Disconnect pneumatic toolfrom the air supply before making any adjustments performing maintenance clearingjammed fasteners orstoring Secure work withclamps or avise in orderto keep handsand body outof potential harm Be sure theworkpiece is properly secure before pressing the tool againstthe material Keep face and body parts away from back ofthe tool cap when working inrestricted areas Sudden recoil canresult in impactto the body especially whennailing into hardor dense material Store idle pneumatictools out ofthe reach ofchildren and donot allow persons unfamiliar with the pneumatic tool orthese instructions tooperate the pneumatictool Pneumatic tools are dangerous
Download Pdf Manuals
Related Search