Nilfisk-Advance America HSC 585 User's Manual
Contents
1. HFT 45 HFT 43 HARD SURFACE MINI TURBO HARD COMBO TOOL SURFACE TOOL 60070045 60070043 e Great fo getting in those small areas e Designed for edging hard surfaces 35 to 172 bar 500 2500 psi e Hose is rated to 172 bar 500 2500 psi e Use water up to 110 C 230 F e Heads lay flat for cleaning under fixtures e Ergonomic design e Use it on floors or walls e Lightweight but sturdy e No wheels to restrict 360 travel e Water temperature up to 110 C 230 F EVOLUTION CARPET WAND IN LINE FILTER 600203099 600709908 e Use it with the 7 bar 100 psi pump on carpets e Connect the filter to the water inlet of most e Its light weight is less fatiguing tools e It recovers more water from the carpet than e Prevents plugged spray jets heavier wands e Comes apart for cleaning e Use with heated water up to 100 C 215 F STAINLESS STEEL HAND TOOL HOOK AND LOOP STRAP 600203099 220202208 e Use it with up to 27 bar 400 psi e Connect the filter to the water inlet of most e Durable tools e Reliable valve e Prevents plugged spray jets e Optional in line filter available e Comes apart for cleaning SPECI Fi CATIONS Vacuum Rated Power Pump Suction Power Vacuum at Nozzle Heat Suction Width Weight Dimensions NOTES ONilfisk MX 585 MULTI 3 stage 2950 W maximum Positive displacement 83 bar amp Demand 7 bar 372 W 30 4 KPA2. REFER TO THE AUTO FILL AND AUTO DUMP INSTRUCTIONS ON THE FOLLOWING PAGES If you choose to use the automatic pump out feature connect the dump hose to the brass hose fitting on the back of the machine and place the open end of the hose in a drain Make sure the drain hose on the back of the vacuum tank is closed and the lid is tight on the recovery tank NOTE never turn ON the automatic pump out switch unless you have removed the brass cap from the hose connector on the rear of the machine This pump will run continuously if it is turned on and if the water can not be pumped out cap still screwed on damage may occur to the pump If you choose not to use the auto pump out option just make sure the brass cap is on the hose connector on the rear of the machine CAUTION do not turn the pump out switch on if the cap is still on the hose connector on the back of the machine If you choose to use the auto fill feature connect the fill hose to the auto fill valve located over the solution tank fill hole Turn on the water source NOTE do not turn the water on full power The water flowing into the auto fill system does not need a lot of pressure behind it Allow the tank to fill with solution When you use the auto fill system the auto fill valve will automatically turn on and turn off as the tank empties and then fills NOTE If you are not going to use the auto fill system just fill the tank with water and cleaning chemical Follow chemical di
3. on the switch for the automatic pump out switch is located on the switch panel on the top of the machine NOTE the pump out pump is self priming When there is water in the recovery tank it will automatically pump out After each job run clear water though the automatic pump out to wash out any chemical residue Remove and clean the stainless steel filter in the back of the tank Reinstall the filter once it is clean Empty and clean the recovery tank Disconnect and roll up the dump hose Clean and dry the machine and accessories DANGER DO NOT USE SOLVENTS OR ANY CHEMICALS THAT MAY BE FLAMMABLE EXPLOSIVE OR COMBUSTIBLE CAUTION always use a defoamer in the recovery tank to prevent water or foam from entering the vacuum motor AUTOMATIC DUMP Hose Connection Dump Power Pump Prime Pedal 11600205211REVA 9 HSC 585 Multi REV A 3 8 08 HSC 585 MULTI CONTR wn e QTY 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PART LIST 220 240V PART No DESCRIPTION 600758501 Reel with hoses complete 600758502 Lid kit 600758503 Vacuum air inlet kit 600758504 Switch plate kit 600758505 Switch and light kit 600758506 Auto fill kit 600758516 Vacuum tank 600758508 Heater outlet kit 600758509 Cord wrap kit 600758510 Solution tank 600758511 Fuse kit 600758512 Water inlet filter kit 6
4. to 100 2C 38 mm 89 5 KG 39 H x 21 W x 36 L ng standards
5. 00758513 Power prime kit 600758514 Drain hose kit 600758515 Power cord kit EU 600758536 Power cord kit UK 600758531 Auto dump pump kit 600758517 Vacuum motor kit 600758518 Pump kit 7 bar 600758519 Pump and motor complete 85 bar 600758520 Pump complete 85 bar no motor 600758544 Pressure regulator unloader valve 600758541 Relay kit vacuum motor 600758542 Relay kit pump motor 600758522 Base 600758523 Pressure gauge kit 600758524 Glide kit for reel 600758525 Heat exchanger replacement kit 600758526 Heat repair kit 600758527 Low pressure pump outlet kit 600758528 Castor kit 2 600758529 Louver kit 600758530 Wheel kit 2 600758538 RFI filter kit 600758532 Latch kit 600758537 Motor no pump 85 bar 600758545 Internal water hoses kit MISCELLANEOUS PARTS AND KITS 1 600758521 600758533 600758534 600758535 600758540 Pump rebuild kit Vacuum hose kit for reel Solution hose kit for reel Label kit Water inlet filter bag 4 in kit ALWAYS USE ONLY ORIGINAL NILFISK PARTS ON YOUR HSC 585 MULTI ACCESSORIES ONilfisk setting standards HFT 40 TURBO HARD SURFACE TOOL 600305899 e Use on all types of hard flooring e Cleaning capacity is up to 93 m or 1000 ft Hr Lightweight but robust e Brush ring attachment e No wheels to restrict 360 travel e Water temperature up to 110 C 230 F e Patented automatic vacuum compensator leaves the floor dryer In line filter keeps spray jets clean
6. ONilfisk setting standards HSC 585 MULTI EXTRACTOR 220 240V EU INFORMATION amp OPERATING INSTRUCTIONS CAUTION DO NOT OPERATE MACHINE A UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL 26022008 IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use for example in hotels schools hospitals factories shops and offices other than normal residential housekeeping purposes When using any electrical appliance basic precautions should always be followed including the following NOTE Read all instructions before using this machine WARNI NG To reduce the risk of fire electric shock or injury Do not leave the machine unattended when it is plugged in Unplug the unit from the power outlet when not in use Unplug the machine from the power outlet before cleaning or servicing Turn off all controls before unplugging To avoid electric shock do not expose to rain or snow Store and use indoors Wear hearing protection if desired The measured sound level of the HSC585 is 75 dB A Do not allow to be used as a toy Close attention is necessary when used near children Use only as described in this manual Use only the manufacturer s recommended attachments Inspect the power cord regularly for damage such as cracking ageing or damaged insulation Do not use with damaged cord or plug If the cord needs to be replaced take the machine to an authorized N
7. TE before servicing any component in the base cabinet remove the hoses and spool before opening the tanks Refer to the instruction on page 3 ING THE AUTOMATIC FILL AND OR AUTOMATI AUTOMATIC FILL INSTRUCTIONS Operation 1 Attach a garden hose to the auto fill hose connection above the holding tank fill hole and connect the other end of the hose to your water source 2 Make sure the float that hangs into the solution tank from the auto fill valve is free of obstruction and can move freely 3 Turn on the water supply Do NOT turn the water on full pressure This system does not require a high presssure water source J ust turn the water on 4 The float for the automatic fill will shut off the flow of incoming water when the tank is nearly full and DUMP it will allow the valve to open again once the water level has dropped to a predetermined level AUTOMATI C FI LL High Pressure Outlet Ta 3 II k D 107 ve gt 8 1 CAR Water Hose Connection F 9 4 AUTOMATI C DUMP INSTRUCTIONS Operation 1 Before each use if necessary unscrew the stainless steel filter inside the recovery tank and clean it Also make sure the float in the recovery tank Is clean 2 Attach a garden hose to the automatic pump out fitting on the back of the base of the machine refer to illustration below 3 Run the other end of the hose into a drain 4 Turn
8. el with hoses from the machine pull the vacuum hose loose from the hose barb on the front of the tank and push the short piece of vacuum hose into the center of the hose spool Disconnect the solution hose quick coupling Grasp the spool from either side and lift it off the machine NOTE before servicing any component in the base cabinet remove the hoses and spool before opening the tanks Record the serial number and model of your new extractor here Model _HSC 585 Multi_ Serial Number Purchase Date 11600205211REVA age KNOW YOUR MACHINE Drain Hose HSC 585 MULTI Drain Hose Cap Wand Holder Vacumm Vacuum Hose Tank Lid Connection 85 Bar Quick Disconnect Solution Tank Garden Hose rl rn ee Wheel ek Connector erie Pedal Wheel Compartment Castor pane peace with Brake Gauge 7 Bar Quick Disconnect HIGH SWITCH PLATE BAES E DUMP PUMP ON OFF SWITCH eL PUMP HEAT VACUUM LICHT SELECTOR ON OFF ON OFF SWITCH SWITCH SWITCH OPERATION REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE 1 CAUTION Never leave the 85 bar pump running if you are not actively using it A CAUTION IF FOAM OR WATER COMES OUT THE VACUUM EXHAUST TURN THE MACHINE OFF IMMEDIATELY HIGH PRESSURE WASHER Before each use inspect the machine hoses and cleaning tools for cleanliness and completeness Make sure hoses are in good condition and the spray nozzle s is tight
9. he base and connect the vacuum hose to the hose barb on the top left of the recovery tank Connect the other ends of both hoses to the cleaning tool Turn on the 7 bar demand pump 4 NOTE the demand pump will not run until pressure is released Spray for a few seconds to fill the lines with solution Wait two minutes to allow the heater to reach temperature Begin cleaning It may take several cycles to heat the lines and the cleaning tool If you are not using the auto fill or auto dump features turn off the pump and the vacuum when the solution tank gets low Fill the solution tank and empty and clean the recovery tank If you are using the automatic features your machine will empty and fill itself no need for you to stop working When finished with the job turn off the water source if using the auto fill feature Remove the auto fill hose from the hose connection on the machine Vacuum the remaining solution from the solution holding tank into the recovery tank Run a few gallons of clean water through the system Drain the recovery tank by placing the drain hose over a floor drain toilet or tub and removing the cap You can clean the tank at this time with clean water When the tank is empty cap the drain hose and place it back in the hook and loop holder Disconnect the hoses from the cleaning tool and reel them up onto the hose spool Unplug the power cords Clean and dry the machine and the tool NO
10. ilfisk If the cord or prongs become damaged have it replaced by an authorized Nilfisk service technician or partner Use a defoamer any time you get foam in the recovery tank to prevent motor damage If foam or liquid comes out of the vacuum motor or exhaust turn the machine off immediately If the machine is not working as it should has been dropped damaged left outdoors or flooded with water return it to a service center Do not pull the machine by the cord do not use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do not run the machine over the cord Keep the cord away from heated surfaces To unplug grasp the plug not the cord Do not handle the plug the cord or the machine with wet hands Extension cords must be 12 3 and no longer than 50 feet Replace the cord or unplug immediately if the ground prong becomes damaged Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes or any health endangering dusts Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Use extra care when cleaning on stairs Connect to a properly grounded outlet only Liquid pumped out could be dangerous because of temperature pressure or chemical content D
11. ntinued 10 11 12 15 If you choose to use the auto fill feature connect the fill hose to the hose connection over the solution tank fill hole Turn on the water source and allow the tank to fill with solution NOTE do not turn the water on to full pressure water flowing into the auto fill system does not need a lot of pressure behind it If you choose not to use the auto fill system just fill the tank with water and cleaning chemical Follow chemical directions regarding dilution and mixing Do not use harsh chemicals as they may damage seals in pumps and valves and cause the pump to wear prematurely NOTE using warm water in the tank may improve the efficiency of the heat exchanger when cleaning with heat but never use water with a temperature exceeding 54 C 130 F Select HEAT by moving the HEAT HIGH PRESSURE switch towards the thermometer symbol NOTE this switch is off when it is set to the middle position and neither the high pressure pump nor the heater is selected When set to the bottom position the heat is selected the red light will come on and stay on The heater and the high pressure pump can not operate at the same time Plug in the power cord Press the power prime pedal located on the rear lower left of the machine for a moment to release any back pressure in the pump lines Connect the solution hose to the quick disconnect on the short hose from the 7 bar pump on the front of t
12. o not let the pump run dry If you run out of water turn the machine off and refill INSPECTION Carefully unpack and inspect your HSC 585 MULTI for shipping damage Each machine is tested and inspected before shipping Any shipping damage incurred is the responsibility of the carrier You should notify the carrier immediately if you notice damage to the box or to the machine or parts CLEANING SOLUTIONS Select a proper pre spray for the surface to be cleaned and apply the pre spray Use a neutral OH rinse or detergent 6 to 9 pH in the HSC 585 to prevent premature wear of the pump seals and other components Powdered chemicals are not recommended MAINTENANCE For optimum performance flush the machine with clear water at the end of each working day Once a month minimum run a flushing compound through the machine to break up any mineral or chemical build up that may have formed in the lines the pumps or the heater The vacuum motor pump motor and the pump do not require any scheduled maintenance however the vacuum motors may require replacement brushes after 1000 1500 hours and the high pressure pump and unloader valve may require rebuild kits after 500 1000 hours refer to machine part list for numbers Clean the body with an all purpose detergent and protect it with an automobile interior polish Lubricate the wheels castors and quick disconnects with an all purpose silicone spray NOTE to remove the complete re
13. rections regarding dilution and mixing Do not use harsh chemicals they may damage seals in pumps and valves and cause the pump to wear prematurely NOTE Never put water in the tank with a temerature exceeding 54 C 130 F Pre spray the area to be cleaned with a pump up sprayer Follow chemical directions Plug in the power cord Turn on the high pressure pump by placing the HIGH PRESSURE HEAT selection Switch 2 in the UP position to select the High Pressure Pump NOTE The high pressure pump and the heat can not operate at the same time NOTE this switch is off when it is set to the middle position and neither the high pressure pump nor the heater is selected 6 The 85 bar pump is not self priming you will need to prime the high pressure pump using the power prime system turn on both the pump and the vacuum cover the hole in the hose barb with your hand then depress the Power Prime Pedal This will pull trapped air out of the pump and into the recovery tank priming the pump You will notice a tone change in the pump smoother with less of a rattle and the water being pulled into the recovery tank will change from a white full of air stream of continue on next page HIGH PRESSURE continued 10 11 13 14 water to a clear solid stream Priming may take 20 60 seconds or even longer sometimes and it will require a full solution tank When the pump is primed let off the Power Prime Pedal and turn off
14. solution from the holding tank into the recovery tank Run a few gallons of clean water through the system Completely empty the recovery tank by placing the drain hose over a floor drain toilet or tub and removing the cap You can clean the tank at this time with clean water When the tank is empty cap the drain hose and place it back in the hook and loop holder Disconnect the hoses from the cleaning tool and reel them up onto the hose spool Unplug the power cord Clean the machine and the tool LOW PRESSURE AND HEAT A CAUTION if foam or water comes out the vacuum exhaust turn the machine off immediately 1 Before each use inspect the machine hoses and cleaning tools for cleanliness and completeness Make Sure hoses are in good condition and the spray nozzle s is tight REFER TO THE AUTO FILL AND AUTO DUMP INSTRUCTIONS ON THE FOLLOWING PAGE 2 If you choose to use the automatic pump out feature connect the dump hose to brass hose fitting on the back of the machine and place the open end of the hose in a drain NOTE NEVER TURN ON THE PUMP OUT PUMP UNTIL YOU HAVE REMOVED THE CAP FROM THE HOSE CONNECTOR ON THE REAR OF THE MACHINE Make sure the drain hose on the back of the vacuum tank is closed and the lid is tight on the recovery tank If you are not going to use the auto pump out option just make sure the brass cap Is on the hose connector on the rear of the machine continue on next page LOW PRESSURE AND HEAT co
15. the pump and the vacuum Then press the Power Prime Pedal once again for a moment to release the line pressure you will hear a swoosh of air as the back pressure in the lines is released The pump will need to be primed anytime air gets into it try not to let the pump run dry Proceed to the next step Add defoamer to the recovery tank Attach the solution spray hose to the solution quick disconnect Attach the vacuum hose to the hose barb on the front of the recovery tank Pull the hoses out from the reel Attach the other ends of the hoses to the cleaning tool If you choose to use the automatic pump out feature MAKE SURE THE CAP IS REMOVED FROM THE HOSE CONNECTION ON THE BACK OF THE MACHINE BEFORE YOU TURN THE SWITCH ON This pump will run continuously once you turn it on and if it tries to pump out water but the cap is still on the hose fitting the pump may be damaged Turn on the vacuum 3 and turn on the dump pump if you chose to use this feature 5 Begin spraying If you are not using the auto fill or auto dump features turn off the pump and vacuum when the solution tank gets low fill the solution tank and empty and clean the recovery tank If you use the auto fill and or auto dump features you will not need to stop working to fill and or empty your tanks When the job is finished turn off the automatic pump out pump turn and turn off the water source if they were employed Use the vacuum hose to suck the remaining
Download Pdf Manuals
Related Search