Nilfisk-Advance America AQUAMAX AX 650 User's Manual
Contents
1. Aeknapauua UZFOTOBUTEA O COOTBETCTBUM AWPEKTUBAM EC PacnbinuTenbHbin Mbistecoc Dauuaa Malina paspa60TaHa B COOTBETCTBUN CO CHEAYHOLLUMU MHCTPYKUMAMU U CTAHAAPTAMU VHcTpykunma no paspa6otke MauuH 98 37 EEC VHctpykuna EMC 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC VHCTpykuma no UCNONBZOBAHNO HUZKUX HanpaxkeHu 73 23 EEC 93 68 EEC CornacoBaHHble craHAapTbI EN 60 335 2 72 Nilfisk Advance A S Sognevej 25 DK 2605 Brondby Denmark Nilfisk Advance Inc F00018 1 03 pas Nilfisk Advance setting standards www nilfisk advance com 20062. Clean Spray Nozzles Check Each Battery Cell s Water Level Inspect Brush Deck Skirt e Inspect amp Clean InLine Pump Filter Lubricate the Machine e Check Carbon Brushes Have a Nilfisk Advance service technician check the vacuum motor carbon brushes once a year or after 300 operating hours The brush and drive motor carbon brushes check every 500 hours or once a year A IMPORTANT Motor damage resulting from failure to service the carbon brushes is not covered under warranty See the Limited Warranty Statement 9 Store the machine in a clean dry place with the tank dome lid open FORM NO 56041551 Aqua MAX AX 650 11 12 ENGLISH PICK UP TOOL MAINTENANCE Check the pick up tools daily Remove any built up string hair or carpet fibers SPRAY NOZZLE MAINTENANCE Remove the spray nozzles once a week Soak the nozzles overnight in a vinegar and water solution to remove chemical deposits LUBRICATING THE MACHINE Once a month or every 30 hours lubricate all pivot points on the pick up tool assembly For best results use a spray silicone lubricant Once amonth pump grease into the grease fittings on the caster wheels until it seeps out around the bearing Wipe off the excess grease to avoid staining carpet CLEANING THE VACUUM MOTOR FILTERS Clean the vacuum motor filters daily with compressed air For extremely dirty filters wash with warm soapy water and rinse thoroughly with clean w
3. 11 The operator can make the machine go forward by pushing forward on it or reverse by pulling backward on it The speed is variable depending on how far forward or backward the paddle is moved The brush and pump will operate when the brush deck is in the DOWN position and the drive paddle is engaged in either direction both will stop 1 second after the drive paddle is released NOTE The pump does not run when the drive paddle is in the reverse position Brush Deck Lift Lever 12 This lever is used to raise or lower the brush deck Both pump and vacuum turn ON when the brush deck is lowered and turn OFF when it is raised if their switches are in the AUTO position NOTE Machine must be moving forward to activate pump forward or reverse to activate brush Vacuum system shuts off 10 seconds after raising the brush deck Upper Tank Latch 13 This latch is used to secure the Upper Tank 1 to the machine to prevent the tank from opening while operating the machine since the Operator Control Handle 10 is mounted to the upper tank Accessory Port 14 This is used to connect external accessories Circuit Breakers 15 6 Amp Control Circuit Provides overload protection If it trips it will pop out To reset wait one minute and press the button back in If any breaker trips repeatedly have the machine serviced 40 Amp Vac Motors Provides overload protection to machine s vacuum motors If it trips it will pop out To reset wait one min
4. Out Cap Brush Access Door Brush Access Door Latch Deck Release Knob Vac Motor Filters Automatic Float Shut Off Waste Water Bladder Roller Bumper InLine Pump Filter Lower solution Tank Roller Bumper Release Knob ADA LA DS S g N NN Ee N FORM NO 56041551 AquaMAX AX 650 7 8 ENGLISH FUNCTIONAL DESCRIPTION OF CONTROLS Upper recovery Tank 1 Waste water recovered from carpet is deposited here inside of a bladder 34 Area outside of waste water bladder 34 is utilized for extra clean solution capacity The batteries and Vac Motor Filters 32 can be accessed by opening this tank to the side Recovery Tank Dome Lid 2 Point of entry for waste water into bladder Also houses Automatic Float Shut Off 33 which shuts off vacuum port to vac motors when bladder is full Remove this lid to rinse out the waste water bladder or to fill the solution tank Battery Fuel Gauge 3 Shows current state of charge of batteries A double flashing light indicates low batteries charge immediately NOTE When the battery fuel gauge shows double flashing lights all systems shut down except the wheel drive system Master Key Switch 4 Main power switch Pump Switch 5 This button is used to select the mode of operation for the solution system There are 3 modes of operation for this system The modes are AUTO OFF ON Following is a description of each mode AUTO MODE In this mode
5. il y a certaines r gles de base que vous devez toujours observer dont celle nonc e ci apr s 1 A Lire toutes les instructions avant d utiliser l appareil A ATTENTION Afin de r duire les risques d incendie de d charge lectrique ou de blessure Cette machine ne pourra tre utilis e que par du personnel parfaitement entra n et d ment autoris Eloignez les batteries de toutes flammes tincelles ou substance fumig ne Les gaz explosifs sont ventil s pendant le fonctionnement normal De plus du gaz hydrog ne explosif s chappe des batteries lorsqu elles sont en charge Ne proc dez au chargement des batteries que dans une zone bien ventil e loin de toute flamme Ne fumez pas proximit des batteries lorsqu elles sont en charge Otez tous vos bijoux lorsque vous travaillez proximit de composants lectriques Positionnez la cl de contact sur off O et d connectez les batteries avant de proc der l entretien des composants lectriques Ne travaillez jamais sous une machine sans y avoir plac au pr alable des blocs de s curit ou des tais destin s soutenir la machine Ne d versez pas d agents nettoyants inflammables ne faites pas fonctionner la machine proximit de ces agents ou d autres liquides inflammables Ne nettoyez pas cette machine avec un nettoyeur pression Ne faites pas fonctionner la machine sur des rampes ou pentes de plus de 2 pour cent Utilisez un
6. most from your Nilfisk Advance AquaMAX AX 650 Readit thoroughly before operating the machine Note Bold numbers in parentheses indicate an item illustrated on pages 6 7 This productis intended for commercial use only PARTS AND SERVICE Repairs when required should be performed by your Authorized Nilfisk Advance Service Center who employs factory trained service personnel and maintains an inventory of Nilfisk Advance original replacement parts and accessories Call the NILFISK ADVANCE DEALER named below for repair parts or service Please specify the Model and Serial Number when discussing your machine Dealer affix service sticker here NAME PLATE The Model Number and Serial Number of your machine are shown on the Nameplate on the machine This information is needed when ordering repair parts for the machine Use the space below to note the Model Number and Serial Number of your machine for future reference MODEL NUMBER SERIAL NUMBER UNCRATE THE MACHINE When the machine is delivered carefully inspect the shipping carton and the machine for damage If damage is evident save the shipping carton sothatitcanbe inspected Contact the Nilfisk Advance Customer Service Department immediately to file a freight damage claim FORM NO 56041551 Aqua MAX AX 650 3 4 ENGLISH IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use for example in hotels schools hospitals fa
7. one battery X X XX FORM NO 56041551 AquaMAX AX 650 13 14 ENGLISH 6 AMP CONTROL CIRCUIT CIRCUIT BREAKER When the Control Circuit Circuit Breaker 15 trips push the button to reset the circuit breaker Ifthe circuit breaker trips repeatedly call your local Nilfisk Advance Distributor for service 20 AMP WHEEL DRIVE CIRCUIT BREAKER When the Wheel Drive Circuit Breaker 15 trips check to see if there is debris wrapped around the wheel axle Remove the debris from the axle Have the wheel drive motor checked for worn out brushes repair or replace the motor if necessary Push the button to reset the circuit breaker Ifthe circuit breaker trips repeatedly call your local Nilfisk Advance Distributor for service 20 AMP BRUSH DRIVE CIRCUIT BREAKER When the Brush Drive Circuit Breaker 15 trips check to see if the brush height is set too low or there is debris wrapped around the brush Adjust the brush height or remove the debris from the brush Push the button to reset the circuit breaker Ifthe circuit breaker trips repeatedly call your local Nilfisk Advance Distributor for service 40 AMP VACUUM MOTOR CIRCUIT BREAKER When the Vacuum Motor Circuit Breaker 15 trips check the Vac Motor Filters 32 and clean or replace ifnecessary Have the vacuum motors checked for worn out bearings and or brushes or bearing failure Repair or replace the motors if necessary Push the button to reset the circuit breaker I
8. strojn m za izeni 98 37 EEC Sm rnice o elektromagnetick kompatibilit 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Sm rnice o nizk m nap ti 73 23 EEC 93 68 EEC Harmonizovan normy EN 60 335 2 72 EU megfelel s gi nyilatkozat HU Permetfelsziv g p Ez a g p az al bbi ir nyelvekkel s szabv nyokkal sszhangban k sz lt G p szeti ir nyelvek 98 37 EEC EMC ir nyelvek 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Kisfesz lts g ir nyelvek 73 23 EEC 93 68 EEC Harmoniz lt szabv nyok EN 60 335 2 72 EU Uygunluk Beyan TK Bataryayla al an zemin f r alama sistemi Bu makine a a daki direktiflere ve standartlara uygun olarak retilmi tir Makine Direktifi 98 37 EEC EMC Direktifi 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC D k voltaj Direktifi 73 23 EEC 93 68 EEC Uyumlu standartlar EN 60 335 2 72 4 4 2004 Larry Doerr Vice President Operations Nilfisk Advance Inc 14600 21st Avenue North Plymouth MN 55447 USA S visiace normy EN 60 335 2 72 Deklaracja zgodno ci z normami UE PL Urz dzenie do wysokoci nieniowego prania dywan w Niniejsze urz dzenie zosta o wyprodukowane w zgodzie z nast puj cymi dyrektywami i normami UE Dyrektywa dotycz ca maszyn 98 37 EEC Dyrektywa kompatybilno elektromagnetyczna 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Dyrektywa urz dzenia elektromagnetyczne niskonapi ciowe 73 23 EEC 93 68 EEC Zharmonizowane normy EN 60 335 2 72
9. the solution flow will be turned ON whenever the brush is lowered and the machine is moving forward The solution flow will be turned off when the machine is not moving moving in reverse or the brush is raised OFF MODE In this mode the solution flow is turned off ON MODE This mode is for accessory use The pump is ON at all times as long as the Master Key Switch 4 is ON Vacuum Switch 6 This button is used to select the mode of operation for the vacuum system There are 3 modes of operation for this system These modes are AUTO OFF ON Following is a description of each mode AUTO MODE In this mode the vacuum will be turned ON whenever the brush is lowered and the Master Key Switch 4 is ON While in this mode the vacuum will remain on for 10 seconds after the brush is raised OFF MODE In this mode the vacuum is off ON MODE This mode is for accessory use The vacuum is ON at all times as long as the Master Key Switch 4 is ON Hourmeter 7 Displays number of hours machine has been used NOTE The hourmeter only runs when the vac motors are running Brush Pressure Indicator 8 This meter should be reading 8 15 amps green zone readings outside this range indicate the need for brush height adjustment Speed Control Knob 9 Turn this knob clockwise to increase maximum speed range and counter clockwise to decrease maximum speed range Operator Control Handle 10 Operator holds onto this handle to maneuver the machine Drive Paddle
10. AguaMAX AX 650 Instructions ForUse Advance MODEL 56212000 Nilfisk MODEL 56212260 Nilfisk Advance setting standards English 3 04 revised 10 06 Form Number 56041551 2 ENGLISH TABLE OF CONTENTS Page INTOUCI N A ida 3 Parts adC a a EE 3 EE EE 3 Uncratingthe Machine AAA 3 Important Safety Instructions benne 4 Consignes de Securite Importantes geegent seien ee dans 5 Know Your Machine EE 6 7 Functional Description of Controls ss 8 Preparing the Machine for Use Installing the Batteries iere a cde cation tear cece ano 9 Fillingthe rue 9 Pr sprayinigithe barnet zlu na ken bb 9 Planfor Cleaning a ins RE aaa 9 Operating the Machine ES ED Ea hh an 10 sue EE 10 AtterUsing the Machines fifi 2er rar hn Ke eg 11 Maintenance Scheuer uereg ge 11 Maintenance Pick Up Tool ET Ee EE 12 Spray Nozzle Maintenance nine 12 Lubricating the Machine siii aaa aros 12 Cleaning the Vacuum Motor Filters sm 12 Adjustingthe Brus iHe eenn a a a a ei 12 Power Brush Maintenance seen 12 Removing the BIS eseri a li 12 Els ue UE 13 CheckingtheBatteryWaterLevel seen dd den nl on nahon 13 IEN 13 Battery Testi EE 13 Troubleshooting Control Circuit Circuit Breaker ss 14 Wheel Drive Circuit Breaker cuidada tias 14 Brush Drive Circuit TEE 14 Vacuum Motor Circuit Breaker hada nn 14 Technical Specific E 14 2 FORM NO 56041551 AquaMAX AX 650 ENGLISH 3 INTRODUCTION This manual will help you get the
11. Brush Deck 12 Turn the Master Key Switch 4 OFF To empty the solution tank pull the Solution Drain Hose 21 off the elbow Direct the hose to a designated waste water DISPOSAL SITE and remove the plug Rinse the tank with clean water Inspect the solution hoses replace if kinked or damaged To empty the recovery tank take the Recovery Drain Hose 17 offits hanger Direct the hose to a designated waste water DISPOSAL SITE and remove the plug hold the end of the hose above the water level in the tank to avoid sudden uncontrolled flow of waste water Rinse the tank with clean water Inspect the recovery and vacuum hoses replace if kinked or damaged Remove the Brush 29 rinse with warm water and remove any built up string hair or carpet fibers Disconnect the Recovery Hose 24 from the Recovery Tank Dome Lid 2 and flush with warm water to wash any debris out of the Recovery Hose Pick Up Tool Assembly NOTE Make sure that you have disconnected the correct hose if you run water into the vac motors they will be damaged Wipe the machine with a damp cloth Do not use abrasive chemicals or solvents Perform any required maintenance before storage MAINTENANCE SCHEDULE MAINTENANCE ITEM Daily Weekly Monthly Y early Charge Batteries Check Clean Power Brush e Check Clean Tanks amp Hoses Check Clean Vacuum Shut Off Float Check Clean Vacuum Motor Filters e Clean Pick Up Tools e
12. ater Allow the filters to dry completely before re installing in the machine MAINTENANCE NOTE Keep a second set of filters on hand to use while first set is drying ADJ USTING THE BRUSH HEIGHT Simply turn the Brush Height Adjustment Knob 19 clockwise to raise and counter clockwise to lower the brush deck NOTE The Brush Pressure Indicator 8 should read 8 15 amps when properly adjusted POWER BRUSH MAINTENANCE Check the brush daily Remove any built up string hair or carpet fibers Check the bristle length Have a service technician change the brush when the brush bristles are worn to 1 2 inch 12 7 mm REMOVING THE BRUSH A CAUTION Turn the key switch off O and remove the key before changing the brushes and before opening any access panels 1 Turn the Master Key Switch OFF and raise the Brush Deck 2 See figure below Unsnap Latch A remove Pin B and Brush Access Door C Slide the brush out of the brush deck housing 3 Toreinstall slide the brush under the brush deck housing make sure the end with the large slots cut into itis inserted first 4 Reach under the left side of the brush deck to guide the end of the brush onto the drive lug E Pushin and turn the brush until itis firmly seated on the drive lug IMPORTANT Make sure that the Bearing Block D is seated securely in the door and orientated as shown for old style EI new style G machines have the bearing block attached to the access door Hold the
13. ctories shops and offices other than normal residential housekeeping purposes When using an electrical appliance basic precautions should always be followed including the following LU A Read all instructions before using A A WARNING To reduce risk of fire electric shock or injury This machine should only be used by properly trained and authorized persons Keep sparks flame and smoking materials away from batteries Explosive gases are vented during normal operation Charging the batteries produces highly explosive hydrogen gas Charge batteries only in well ventilated areas away from open flame Do not smoke while charging the batteries Remove all jewelry when working near electrical components Turn the key switch off O and disconnect the batteries before servicing electrical components Never work under a machine without safety blocks or stands to support the machine Do not dispense flammable cleaning agents operate the machine on or near these agents or operate in areas where flammable liquids exist Do not clean this machine with a pressure washer Do not operate this machine on ramps or inclines of more than a 2 percent gradient Only use the brushes provided with the appliance or those specified in the instruction manual The use of other brushes may impair safety CAUTION This machine is not approved for use on public paths or roads This machine is not suitable for picking up hazardous du
14. dards EN 60 335 2 72 Dichiarazione di conformit CEE I Macchina ad estrazione E prodotto in conformita alle disposizioni contenute nelle Direttive del Consiglio dei Ministri M direttiva 98 37 EEC EMC direttiva 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC LV direttiva 73 23 EEC 93 68 EEC Norme armonizzate EN 60 335 2 72 EG Konformitatserklarung Spr hextraktionsmaschine Diese Maschine wurde gem den folgenden Richtlinien hergestellt Maschinerichtlinie 98 37 EWG EMV Richtlinie 89 336 EWG 92 31 EWG 93 68 EWG 98 13 EWG Niederspannungsrichtlinie 73 23 EWG 93 68 EWG Harmonisierte normen EN 60 335 2 72 Anioonnpocapuovnc sv ppoocnc EU GR Mnxavnna ka ap opov YAALOV WEKOOUOL AVAPPOPNONG To UNXAVNUA VY EL KATHOKEDQOTEL OVUYOWA HE TIG TAPAKATO TPOG 1AYPAYEG TIpociaypaon ungavnnoroc 98 37 EEC Ilpociapayn EMC 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Tlpoctaypayn xann ng raoeoc 73 23 EEC 93 68 EEC Evapuovioueva nporvna EN 60 335 2 72 ES atbilstibas deklar cija LV lakatu ekstrakcijas ma ina I ma na izgatavota atbilsto i d m direkt v m un standartiem Ma nu direkt va 98 37 EEC Elektromagn tisk s savietojam bas EMC direkt va 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Zemsprieguma direkt va 73 23 EEC 93 68 EEC Saskanotie standarti EN 60 335 2 72 GB IRL D A AX 650 D claration CE de conformit Injecteur extracteur Cette machine a t fabriqu e conform ment aux direct
15. e recovery tank must be emptied The machine will not pick up water with the float closed 11 When the operator wants to stop cleaning or the recovery tank is full raise the Brush Deck Lift Lever 12 This will automatically stop the brush pump and vacuum motors 12 Drive the machine to a designated waste water DISPOSAL SITE and empty the recovery tank To empty pull the Drain Hose 17 from it s rear storage area then remove the plug hold the end of the hose above the water level in the tank to avoid sudden uncontrolled flow of waste water Refill the solution tank and continue cleaning USING ATTACHMENTS To use accessory tools attach the accessory recovery hose to the front port of the Recovery Tank Dome Lid 2 Attach the accessory solution hose to the Accessory Port 14 Connect the other ends of the hoses to the accessory tool When using accessory tools raise the Brush Deck 20 and place the Pump 5 and Vacuum 6 Switches in the ON position See your Nilfisk Advance Distributor for accessories that may be used with the AguaMAX AX 50including 56250185 PowerHead 12 56204223 Drag Tool SS 4 Ft 56204224 Hand Tool SS 56249318 Scrub amp Vac Hose 15 Ft 56801000 Aqua Kit Includes PN 56800385 56800390 amp 56249318 56800390 Drag Tool Plastic 56800385 Hand Tool Plastic 10 FORM NO 56041551 AquaMAX AX 650 ENGLISH 11 AFTER USING THE MACHINE 1 2 3 4 7 8 Raise the
16. en Servicing Batteries Remove all jewelry Donotsmoke Wear safety glasses rubber gloves and a rubber apron Workin a well ventilated area Do not allow tools to touch more than one battery terminal at a time A CAUTION Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly Batteries should be installed by Nilfisk Advance a qualified electrician or the battery manufacturer 1 Removethe batteries from their shipping crate and carefully inspect them for cracks or other damage If damage is evident contact the carrier that delivered them or the battery manufacturer tofile a damage claim Turn the Master Key Switch 4 OFF and remove the key Open the Upper recovery Tank 1 Remove the battery cables frominside the battery compartment Your machine comes from the factory with enough battery cables toinstall six 6 volt batteries Carefully liftthe batteries into the battery compartment and arrange them exactly as shown Secure the batteries as close to the back ofthe machine as possible The terminals on the battery cables are marked for positive and for negative Install the battery cables as shown with the terminals marked onthe positive battery terminals andthe terminals marked on the negative terminals Position the cables so the battery caps can be easily removed for battery service Carefully tighten the nutin each battery ter
17. end of the brush up while re installing Brush Access Door C to ensure that the Bearing Block on the inside of the door is securely seated in the end of the brush 6 Re installPin B and re secure Latch A Latch should secure easily If it has to be forced recheck the position of the brush ul 12 FORM NO 56041551 AquaMAX AX 650 ENGLISH 13 CHARGING THE BATTERIES Charge the batteries when the Battery Fuel Gauge 3 shows a double flashing light A WARNING Use extreme caution when working with batteries Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or eyes Explosive hydrogen gas is vented from the batteries through openings in the battery caps This gas can be ignited by any electrical arc spark or flame When Servicing Batteries Remove all jewelry Donotsmoke Wear safety glasses rubber gloves and a rubber apron Workin a well ventilated area Do not allow tools to touch more than one battery terminal at a time Check the fluid level in each battery cell before charging Add distilled water only until the water level is 1 4 above the plates Push the connector from the charger into the Battery Charger Connector 16 on the machine Follow the instructions on the battery charger A CAUTION To avoid damage to floor surfaces wipe water and acid from the top of the batteries after charging CHECKING THE BATTERY WATER LEVEL Check the water leve
18. es should be charged once a month to prevent the batteries from sulfating Almostall battery caps are vented so there s no need to loosen or remove them for charging Keep the Batteries Clean Monthly Use a damp cloth to wipe dirt from the top of the batteries Battery terminals must be clean and tight If the tops of the batteries are wet after charging the batteries have probably been over filled or over charged Note If there is acid on the batteries wash the tops of the batteries with a solution of baking soda and water 2 tablespoons of baking soda to 1 quart of water BATTERY TESTING A battery problem is usually recognized by the machine operator as a decrease in the machine s running time This condition is usually caused by one or more dead cell in the battery system thatis one or more cell that is putting out less voltage than the other cells Note Always charge batteries before testing There are 2 ways to find a dead cell Use a hydrometer to check the specific gravity or state of charge of the fluid in each cell A dead cell is one that reads 50 points or more lower than the other cells Use a volt meter to check the voltage of each battery with the brush motor running The battery with the dead cell will read 1 or 2 volts lower than the other batteries inthe system Ifthe batteries in the machine are more than 1 year old it s usually best to replace the whole set rather than replacing just
19. fthe circuit breaker trips repeatedly call your local Nilfisk Advance Distributor for service TECHNICAL SPECIFICATIONS as installed and tested on the unit Model AquaMAX AX 650 Model No 56212000 56212260 Voltage batteries V 36V Battery capacity Ah 238 Protection grade IPX3 Sound power level as per ISO 3744 at operator dB A 20 Pa 76 Gross weight with acc and batteries full tank lbs kg 1 171 1531 Vibrations atthe Hand Controls m s lt 2 5m s 14 FORM NO 56041551 AquaMAX AX 650 Nilfisk Advance setting standards TYPE EU Overensstemmelseserklaering T pperensemaskine Maskinen er fremstillet i overensstemmelse med f lgende direktiver Maskindirektiv 98 37 E F EMC direktiv 89 336 E F 92 31 E F 93 68 E F 98 13 EOF Lavsp ndingsdirektiv 73 23 E F 93 68 E F Harmoniserede standarder EN 60 335 2 72 EU verensst mmelsef rs kran Golvv rdsmaskin Maskinen r tillverkad i verensst mmelse med f ljande direktiver Maskindirektiv 98 37 EEG EMC direktiv 89 336 EEG 92 31 EEG 93 68 EEG 98 13 EEG L gsp nningsdirektiv 73 23 EEG 93 68 EEG Harmoniserade standarder EN 60 335 2 72 EU Declaration of Conformity Spray extraction machine This machine was manufactured in conformity with the following directives and standards Machine Directive 98 37 EEC EMC directive 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Low voltage directive 73 23 EEC 93 68 EEC Harmonized stan
20. g the AquaMAX AX 650 automatic extractor PRE SPRAYING THE CARPET Pre spray spots and heavy traffic areas before extracting Use a hand held bottle sprayer or a pressurized Hudson type sprayer Mix the pre spray according to the chemical manufacturer s directions PLAN FOR CLEANING Before you begin extracting look at the area to be cleaned and plan your work Divide the space into sections Overlap each pass 2 inches 5cm FRONT ool 100 FORM NO 56041551 AquaMAX AX 650 9 10 ENGLISH 1 2 A OPERATING THE MACHINE Followthe instructions in the Preparingthe 25 Machinefor Usesection of this manual Make sure the Solution Fill Cap 22 and the res Maintenance Recovery Tank Dome Lid 2 are firmly in place Make sure the Pump Switch 5 and the Vacuum Switch 6 are both in the AUTO position Restoration Turn the Master Key Switch 4 ON Adjust the Nozzle Selector Knob 25 to either the maintenance or restoration mode Setthe Speed Control Knob 9 to the corresponding maintenance or restoration setting Lower the Brush Deck 20 to the floor using the Brush Deck Lift Lever 12 When the Drive Paddle 11 is in the neutral position the brush does not run and solution is not dispensed Grip
21. iquement les brosses fournies avec l appareil ou celles sp cifi es dans le manuel d instructions L utilisation d autres brosses peut mettre la s curit en p ril u PRUDENCE Cette machine n est pas concue pour une utilisation sur les chemins ou voies publics Cette machine n est pas congue pour le ramassage des poussi res dangereuses Lors de l utilisation de cette machine assurez vous que des tiers et notamment des enfants ne courent pas le moindre risque Avant de proc der toute op ration d entretien veuillez lire attentivement toutes les instructions qui Sy rapportent Ne laissez pas la machine sans surveillance sans avoir au pr alable coup le contact enlev la cl de contact O et tir le frein main Positionnez la cl de contact sur off O avant de remplacer les brosses ou d ouvrir tout panneau d acc s Prenez toutes les mesures n cessaires pour viter que les cheveux les bijoux ou les v tements amples ne soient entra n s dans les parties mobiles de la machine Faites attention lorsque vous d placez cette machine dans un endroit o la temp rature peut descendre sous 0 Car l eau contenue dans la solution dans les r servoirs de r cup ration ou dans les conduites risquerait de geler Prenez soin d enlever les batteries de la machine avant de mettre cette derni re au rebut Pour ce qui est de l limination des batteries conformez vous aux r glementations locales en mati re d environnemen
22. ives suivantes R glementation machine 98 37 CEE R glementation 89 336 CEE 92 31 CEE 93 68 CEE 98 13 CEE R glement basse tension 73 23 CEE 93 68 CEE Normes harmonis es EN 60 335 2 72 EG conformiteitsverklaring Sproei extractie machine Deze machine is vervaardigd overeenkomstig de volgende richtlijnen Machine richtlijn 98 37 EEC EMC richtlijn 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Laagspanning richtlijn 73 23 EEC 93 68 EEC Geharmoniseerde normen EN 60 335 2 72 Declaracion de conformidad de la CEE E M quina inyecci n extracci n Esta m quina ha sido fabricada en conformidad a las siguientes normativas Normativa de la m quina 98 37 CEE Normativa EMC 89 336 CEE 92 31 CEE 93 68 CEE 98 13 CEE Normativa sobre baja tensi n 73 23 CEE 93 68 CEE Normas armonizadas EN 60 335 2 72 EU Declara o de conformidade da CE Maquina de injecg o extrec o Esta m quina foi fabricada em conformidae com as seguintes directrizes Directriz de maquinaria 98 37 CEE Directriz EMC 89 336 CEE 92 31 EEC 93 68 CEE 98 13 CEE Directriz de baixa voltagem 73 23 CEE 93 68 CEE Normas harmonizadas EN 60 335 2 72 EU n yhdenmukaisuudesta direktiiveihin Painehuuhtelukone On valmistettu noudattaen yhteis n maaraamia direktiivej B F NL B M direktiivi 98 37 CEE EMC direktiivi 89 336 CEE 92 31 CEE 93 68 CEE 98 13 CEE LV direktiivi 73 23 CEE 93 68 CEE Yhdenmukaistetut standardit EN 60 335 2 72 EL vastavusdeklaratsi
23. l of the batteries at least once a week After charging the batteries remove the vent caps and check the water level in each battery cell Use distilled or demineralized water in a battery filling dispenser available at most auto parts stores to fill each cell to the level indicator or to 10 mm over the top of the separators DO NOT over fill the batteries A CAUTION Acid can spill onto the floor if the batteries are overfilled Tighten the vent caps Wash the tops of the batteries with a solution of baking soda and water 2 tablespoons of baking soda to 1 liter of water BATTERY MAINTENANCE Proper maintenance of electric vehicle batteries can greatly extend their life Well maintained batteries may last up to 3 years but failure after 1 year is common if maintenance has been poor There are 3 simple rules for good battery maintenance Maintain Proper Electrolyte Level Weekly Use distilled water in batteries whenever possible If batteries are discharged add just enough water to cover the plates in each cell If batteries are fully charged fill each cell to the bottom of the filler tube Do notover fill the batteries Do not add acid to batteries Keep the Batteries Charged Weekly Batteries should be charged each time that a machine is used for more than 1 hour Machine operators should open the battery compartment cover for charging to avoid a concentrated build up of hydrogen gas Even when a machine is stored the batteri
24. minal until the terminal will not turn on the battery post Then tighten the nut one additional turn Do not over tighten the terminals or they will be very difficult to remove for future service X X XX 7 Coatthe terminals and posts with spray on battery terminal coating available at most auto parts stores 8 Putone ofthe black rubber boots over each of the terminals FILLING THE SOLUTION TANK Either remove the Solution Fill Cap 22 or the Recovery Tank Dome Lid 2 NOTE When filling the solution tank via the top of the Upper Tank 1 make sure that you pour the solution into the opening closestto the front of the machine Read the dilution instructions on the chemical container Then figure the proper amount of chemical to mix with 40 gallons 151 41 liters of water For best results use the Nilfisk Advance CarpeTeam Extraction Cleaner chemical specially formulated for use with Nilfisk Advance carpet extractors Pour the chemical into the solution tank and fill the tank with warm water NOTE Watch the Solution Level Indicator 21 as you fill the tank When itreaches the 40 gallon mark stop Put the Solution Filler Cap 22 or the Recovery Tank Dome Lid 2 back on the machine NOTE Make sure the Dome Lidis properly seated on the tank A CAUTION Use low sudsing liquid detergents designed for carpet extraction BEFORE USING THE AQUAMAX AX 650 Thoroughly vacuum the carpet to be cleaned before usin
25. ntake filters for vacuum motor assembly Refer to the maintenance chart for maintenance intervals Automatic Float Shut Off 33 The float shut off blocks the vacuum port when the Waste Water Bladder 34 is full You can tell when the float closes by the sudden change in sound of the vacuum motors When the float closes the recovery tank must be emptied The machine will not pickup water with the float closed Waste Water Bladder 34 Contains waste water as it is recovered from carpet Total capacity of 30 gallons 113 5 Liters Roller Bumper 35 This is a 3 position slide out bumper to aid in machine maneuvering along walls InLine Pump Filter 36 This filter removes debris from the solution prior to flowing through the pump Drain solution prior to cleaning this filter Lower solution Tank 37 This tank in combination with the upper tank brings total solution capacity to 40 gallons 151 4 Liters Roller Bumper Release Knob 38 This knob allows you to slide the roller bumper out or in to limit how close the machine travels to the wall 8 FORM NO 56041551 AquaMAX AX 650 ENGLISH 9 INSTALLING THE BATTERIES A WARNING Use extreme caution when working with batteries Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or eyes Explosive hydrogen gas is vented from the batteries through openings in the battery caps This gas can be ignited by any electrical arc spark or flame Wh
26. oon ET Pihustusmasin K esolev masin on valmistatud koosk las jargmiste direktiivide ja standarditega Masinadirektiiv 98 37 EEC Elektromagnetilise sobivuse direktiiv 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Madalpinge direktiiv 73 23 EEC 93 68 EEC Uhtlustatud standardid EN 60 335 2 72 PareiSkimas apie atitikima ES direktyvoms LT Skys io surinkimo ma ina Sis jrenginys pagamintas laikantis tokiy direktyvy bei standartu rengim direktyva 98 37 EEC EMC direktyva 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC emos jtampos rengim direktyva 73 23 EEC 93 68 EEC Harmonizuoti standartai EN 60 335 2 72 Nilfisk Advance Inc F00018 1 03 pas Deklaracija EU o skladnosti SL Stroj za razpr evanje istila Ta stroj je izdelan v skladu z naslednjimi smernicami in standardi Smernica o strojih 98 37 EEC Smernica o elektromagnetni zdru ijivosti EMC 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Smernica o nizki napetosti 73 23 EEC 93 68 EEC Prehl senie o s lade EU Zariadenie na ods vanie povrchov ho postreku Toto zariadenie bolo vyroben v s lade s nasleduj cimi direkt vami a normami Direkt va o zariadeniach 98 37 EEC Direkt va EMC 89 336 EEC 92 31 EEC 93 68 EEC 98 13 EEC Direkt va o n zkom nap t 73 23 EEC 93 68 EEC Harmonizirani standardi EN 60 335 2 72 EU Prohl en o shod CS Ods vac stroj Tento stroj byl vyroben ve shod s n sleduj c mi sm rnicemi a normami Sm rnice o
27. rough the front opening at the top of the Upper Tank after removing the Recovery Tank Dome Lid Vacuum Hose 23 This hose connects to the vac motor assembly in order to create a vacuum inside the waste water bladder Recovery Hose 24 This hose connects between the Pick Up Tools 18 and the Recovery Tank Dome Lid 2 to bring waste water into the bladder Nozzle Selector Knob 25 Use this knob to select either Maintenance Mode or Restoration Mode NOTE The Speed Control Knob 9 has two corresponding settings Maintenance Mode Lower solution flow higher travel speed Recommended for frequent surface cleaning Restoration Mode Higher solution flow lower travel speed Recommended for less frequent deep cleaning Stabilizer Caster 26 This caster provides stability to the unit when opening the Upper recovery Tank 1 Rear Caster 27 These two casters along with the main drive wheel bear the weight of the machine and allow easy maneuvering around corners Lower solution Tank Flush Out Cap 28 This cap allows access to the Lower solution Tank for the purpose of flushing with clean water Brush Access Door 29 The power brush can be removed or installed via this door Brush Access Door Latch 30 Unsnap this latch to allow access to the power brush Deck Release Knob 31 Pull this knob out and slide Brush Deck out to the right until it latches in place This allows cleaning under shelves railings etc Vac Motor Filters 32 I
28. st When operating this machine ensure that third parties particularly children are not endangered Before performing any service function carefully read all instructions pertaining to that function Do not leave the machine unattended without first turning the key switch off O removing the key and securing the machine Turn the key switch off O and remove the key before changing the brushes and before opening any access panels Take precautions to prevent hair jewelry or loose clothing from becoming caught in moving parts Use caution when moving this machine in below freezing temperature conditions Any water in the solution or recovery tanks or in the hose lines could freeze The batteries must be removed from the machine before the machine is scrapped The disposal of the batteries should be safely done in accordance with your local environmental regulations Do not use on surfaces having a gradient exceeding that marked on the machine All doors and covers are to be positioned as indicated in the instruction manual before using the machine SAVE THESE INSTRUCTIONS 4 FORM NO 56041551 AquaMAX AX 650 ENGLISH 5 CONSIGNES DE SECURITE IMPORTANTES Cette machine est destin e un usage commercial et peut entre autres tre utilis e dans les h tels coles h pitaux usines magasins et bureaux Elle n a donc pas t con ue pour l entretien m nager Lorsque vous utilisez un appareil lectrique
29. t N utilisez pas sur des surfaces dont la pente d passe celle mentionn e sur la machine Toutes les portes et couvercles doivent tre dans la position mentionn e dans le manuel d instruction avant de mettre la machine en service CONSERVEZ SOIGNEUSEMENT CES INSTRUCTIONS FORM NO 56041551 Aqua MAX AX 650 5 6 ENGLISH KNOW YOUR MACHINE As you read this manual you will occasionally run across a bold number in parentheses example 2 These numbers refer to an item on this page Refer back to this page whenever necessary to pinpoint the location of an item mentioned in the text Upper recovery Tank Recovery Tank Dome Lid Battery Fuel Gauge Master Key Switch Pump Switch Vacuum Switch Hour Meter Brush Pressure Indicator Speed Control Knob Operator Control Handle Drive Paddle Brush Deck Lift Lever Upper Tank Latch Accessory Port Circuit Breakers 6 Amp Control Circuit 40 Amp Vac Motors 20 Amp Brush Motor 20 Amp Drive Motor Woon CD LD E YN Fe k k ka k a 01 P LAM k 16 17 18 Battery Charger Connector Recovery Tank Drain Hose Pick Up Tool Brush Height Adjustment Knob Brush Deck Solution Drain Hose Level Indicator Solution Fill Cap Vacuum Hose Recovery Hose Nozzle Selector Knob Stabilizer Caster Rear Caster 6 FORM NO 56041551 AquaMAX AX 650 ENGLISH 7 28 29 31 32 34 35 37 38 Lower solution Tank Flush
30. the Operator Control Handle 10 and push the Drive Paddle 11 forward to startthe brush motor and the solution and to move the machine forward For best results move the machine at full speed assuming that step 5 has been completed Pull the Drive Paddle 11 backward to move the machine in reverse The brush will turn in the opposite direction while moving the machine in reverse and solution will not be dispensed Begin cleaning by driving the machine forward in a straight line and overlap each pass by 2 inches 5 cm Turn the Pump Switch 5 OFF prior to turns to ensure complete extraction of solution from carpet Guide the right side ofthe machine along the wall when cleaning the perimeter ofthe room Watch the fluid entering the Recovery Tank Dome Lid 2 If there is a large amount of suds in the recovery tank add a defoamer chemical to the recovery tank CAUTION Empty the recovery tank before the fluid or foam enters the Vacuum Hose 23 at the rear of the Recovery Tank Dome Lid If there is little or no fluid entering the recovery tank check the Solution Drain Hose Level Indicator 21 the solution tank may be empty Refill the solution tank with water and the proper ratio of cleaning chemical 10 The recovery tank has an Automatic Float Shut Off 33 to block the vacuum system when the recovery tank is full You can tell when the float closes by the sudden change in the sound of the vacuum motors When the float closes th
31. ute and press the button back in If any breaker trips repeatedly have the machine serviced 20 Amp Brush Motor Provides overload protection to machine s brush motor If it trips it will pop out To reset wait one minute and press the button back in If any breaker trips repeatedly have the machine serviced 20 Amp Drive Motor Provides overload protection to machine s wheel drive motor If it trips it will pop out To reset wait one minute and press the button back in If any breaker trips repeatedly have the machine serviced Battery Charger Connector 16 Plug battery charger into this port to charge batteries Recovery Tank Drain Hose 17 Used to empty the recovery tank NOTE Hold the end of the hose above the water level in the tank to avoid sudden uncon trolled flow of waste water when removing plug Pick Up Tool 18 Removes excess solution from carpet after scrubbing Brush Height Adjustment Knob 19 Used to adjust the height of the brush deck Turn clockwise to raise the brush deck and counter clockwise to lower the brush deck NOTE Use this adjustment knob in conjunction with the Brush Pressure Indicator 8 Brush Deck 20 Contains brush drive motor and brush Solution Drain Hose Level Indicator 21 Used to empty the solution tank and show current level of solution in tank graduations are marked on the side of the machine next to the hose Solution Fill Cap 22 The solution tank can be filled at this location or th
Download Pdf Manuals
Related Search