Niles Audio IW650FX User's Manual
Contents
1. LIMITED WARRANTY 16 NILES AUDIO CORPORATION NILES WARRANTS ITS PASSIVE LOUDSPEAKER PRODUCTS THOSE NOT REQUIRING AC OR BATTERY POWER TO THE ORIGINAL PURCHASER TO BE FREE OF MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF FIVE YEARS FROM DATE OF PURCHASE THIS WARRANTY IS SUBJECT TO THE FOLLOWING ADDITIONAL CONDITIONS AND LIMITATIONS THE WARRANTY IS VOID AND INAPPLICABLE IF NILES DEEMS THAT THE PRODUCT HAS BEEN USED OR HANDLED OTHER THAN IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER INCLUDING BUT NOT LIMITED TO DAMAGE CAUSED BY ACCIDENT MISHANDLING IMPROPER INSTALLATION ABUSE NEGLIGENCE OR NORMAL WEAR AND TEAR OR ANY DEFECT CAUSED BY REPAIR TO THE PRODUCT BY ANYONE OTHER THAN NILES OR AN AUTHORIZED NILES DEALER TO OBTAIN WARRANTY SERVICE TAKE THE UNIT TO THE NEAREST AUTHORIZED NILES DEALER WHO WILL TEST THE PRODUCT AND IF NECESSARY FORWARD IT TO NILES FOR SERVICE IF THERE ARE NO AUTHORIZED NILES DEALERS IN YOUR AREA YOU MUST WRITE TO NILES AND INCLUDE YOUR NAME MODEL AND SERIAL NUMBER OF YOUR UNIT ALONG WITH A BRIEF DESCRIPTION OF THE PROBLEM A FACTORY RETURN AUTHORIZATION NUMBER WILL BE SENT TO YOU DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES IF THE ABOVE CONDITIONS ARE MET THE PURCHASER S SOLE REMEDY SHALL BE TO RETURN THE PRODUCT TO NIL2. Figure 5 Two pairs of loudspeakers reproduce Dolby Surround EX surround sound in a home theater room Left Optional Placement 2 Remove the magnetic grille starting at a corner and gently pulling the grille outwards as you work around the edges 3 At each loudspeaker route the loudspeaker and optional trigger wire through the provided channel to the input connectors then separate the loudspeaker wire so that at least 2 inches of each conductor are free Strip away 1 4 inch of insulation from each loudspeaker wire If you wish to use the 12 volt triggered Dipole Bipole automated feature please insert 1 8 3 5mm plug above speaker inputs Refer back to page 5 for details 4 On each set of loudspeaker connectors press down the spring loaded connector insert the appropriate conductor and then release the connector as shown in Figure 5 Gently tug on the loudspeaker wire to make sure it is held in place If not repeat this procedure until it is NOTE OBSERVE CORRECT POLARITY POSITIVE GOES TO THE RED POST AND NEGATIVE GOES TO THE BLACK POST IF YOU ARE UNSURE OF WIRE POLARITY SEE THE SECTION CHECKING LOUDSPEAKER PHASE ON PAGE 9 5 Connect the other end of each loudspeaker wire to the receiver or amplifier in the same way 6 Check that loudspeaker is level and then tighten the eight large screws using a 2 Phillips bit This should pull the frame and mounting dog tog
3. YOUR EXISTING SURROUND SOUND SYSTEM CONSULT YOUR LOCAL NILES DEALER FOR MORE INFORMATION Right Left Le Rear Right Rear Left THE BOUNDARY EFFECT Figure 4 Two pairs of loudspeakers reproduce Dolby Surround EX surround sound in a home theater room Placing a loudspeaker in a corner can powerfully affect the way a listener perceives bass response Known as the boundary effect placing loudspeakers close to a wall ceiling boundary or near a corner wall boundary will emphasize certain bass frequencies while canceling others This effect can make the loudspeaker sound excessively boomy and inaccurate to some listeners while to others it just seems like more bass sound As a good rule of thumb if you like listening to your current pair of loudspeakers with the bass turned up you ll enjoy corner placement However if you listen with the tone controls at neutral try keeping the loudspeakers at least 2 or 3 feet from the boundaries of the room CONTINUED ON NEXT PAGE FINISHING THE INSTALLATION CONNECTING amp INSTALLING THE LOUDSPEAKER 1 Please be sure to install the correct loudspeaker in the correct room position Look on the rear label for Right or Left designation Install in the appropriate position as viewed from the listening position facing the video display Lo Right Rear _ Optional Right Placement
4. CLEANING Clean the StageFront Home Theater Solutions loudspeaker with a dampened soft cloth or paper towel If the loudspeaker is mounted high up on a wall or ceiling use a broom to gently brush it off SPECIFICATIONS IW650FX Recommended Amplifier Power 15 to 125 watts per channel Nominal Impedance 6 ohm nominal 3 2 ohm minimum Frequency Response 80Hz to 20kHz dB Sensitivity 88 dB with 2 83 V pink noise input measured at 1 meter on axis Frame Dimensions 21 1 2 x 11 Hole Cut Out Dimensions 19 7 8 x 9 3 8 Depth From Front of Wall 3 7 8 Wiring Requirements We recommend using 16 gauge loudspeaker wire for runs up to 80 feet and 14 gauge loudspeaker wire for runs up to 200 feet The connectors will accommodate up to 12 gauge wire IW770FX Recommended Amplifier Power 15 to 125 watts per channel Nominal Impedance 6 ohm nominal 3 2 ohm minimum Frequency Response 70Hz to 20kHz dB Sensitivity 90 dB with 2 83 V pink noise input measured at 1 meter on axis Frame Dimensions 25 3 4 x 12 Hole Cut Out Dimensions 24 1 4 x 10 1 2 Depth From Front of Wall 3 7 8 Wiring Requirements We recommend using 16 gauge loudspeaker wire for runs up to 80 feet and 14 gauge loudspeaker wire for runs up to 200 feet The connectors will accommodate up to 12 gauge wire NOTES NOTES
5. EDS WE RECOMMEND USING STAGEFRONT LCR LOUDSPEAKERS PLACING THE STAGEFRONT FX AS THE SIDE LEFT AND RIGHT LOUDSPEAKERS In home theater the goal is to reproduce the experience of a great movie theater in your home The biggest difference between the two venues is the use of a rear or surround loudspeaker array in a commercial theater Here it is not uncommon to see 20 or 30 loudspeakers placed around theater walls This huge array of loudspeakers assures the audience will feel completely surrounded by the ambient soundtrack of the movie Filmmakers carefully use the surround soundtrack to envelope viewers in the sound environment on screen They will place background music rain sounds traffic noise etc on the surround soundtrack to create desired effects However in a home with a single pair of front loudspeakers this surround effect will be lost and jungle sounds may actually sound like they are emanating from the middle of your head just like headphones Each StageFront FX loudspeaker is equipped with a BIPOLE DIPOLE front switch as well as a 12 volt trigger jack on the rear of the enclosure This jack will switch the StageFront FX loudspeaker from the front switch setting to its opposite position such as from a setting of Dipole to Bipole for as long as voltage is applied to this connection Tip is positive Use a source that will supply 12 volts DC 200 mA minimum for this trigger These controls optimize the surroun
6. ES IN WHICH CASE NILES WILL REPAIR OR REPLACE AT ITS SOLE OPTION THE DEFECTIVE PRODUCT WITHOUT CHARGE FOR PARTS OR LABOR NILES WILL RETURN A UNIT REPAIRED OR REPLACED UNDER WARRANTY BY SHIPPING SAME BY ITS USUAL SHIPPING METHOD FROM THE FACTORY ONLY AT ITS EXPENSE WITHIN THE UNITED STATES OF AMERICA THERE ARE NO OTHER WARRANTIES INCLUDING WITHOUT LIMITATION EITHER EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER PURCHASER NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE EXTENT PROVIDED OR PROHIBITED BY APPLICABLE LAW SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE FOR THE NAME OF YOUR NEAREST AUTHORIZED NILES DEALER CONTACT NILES AUDIO CORPORATION P O BOX 160818 MIAMI FLORIDA 33116 0818 Please fill in your product information and retain for your records Model Serial No Purchase Date DETACH HERE AND RETURN TO NILES AUDIO CORPORATION WARRANTY REGISTRATION DEPT BOX 160818 MIAMI FLORIDA 33116 0818 WARRANTY REGISTRATION CARD Model Purchased Serial Number Date Purchased month day year Deal
7. OLE DIPOLE switch located on the front as shown in Figure 8 Set the BIPOLE DIPOLE switch on each StageFront FX loudspeaker according to the loudspeaker s side or rear placement as shown in Figure 8 Here are some tips on usage Use the DIPOLE setting on rear loudspeakers when listening to movies and classical music The sound will be less focused as it is reflected along the room s boundaries This is the best choice since most films are mixed using non localized surround effects and classical music is usually recorded in a favorable acoustic environment Use the BIPOLE setting on rear loudspeakers when listening to discrete multi channel recordings that equally emphasize front and surround sounds For multiple sets of StageFront FX loudspeakers use the DIPOLE setting on the side loudspeakers aimed at the listening position for a more DIFFUSE surround effect For the rear loudspeakers use the BIPOLE setting to focus the sound With the 1 8 3 5 mm trigger input for Bipole Dipole mode switching an IR macro can be used to control the loudspeaker mode You can program this as part of your source selection This is an easy way to have Dipole envelopment for Movie sources and Bipole performance for Music sources refer to page 5 for details ACOUSTIC FINE TUNING Each StageFront In Wall FX loudspeaker features a Diffuse Sound Level control located on the front for acoustic fine tuning after installation as shown in Figure 8 Adj
8. SE Loudspeaker wire has two conductors On both your loudspeaker and amplifier one conductor is attached to the negative terminals while the other is attached to the positive terminals Usually the wire is marked for your convenience but the marking can be done in the following different ways Stripe on one wire Ribbed area you can feel on one conductor Different colors of metal wire on each conductor Fabric strand or string wound into one of the conductors Of course there are some wires that appear completely identical So be careful or you might make a connection mistake If you do one loudspeaker will be playing out of phase with the other loudspeaker A pair of out of phase loudspeakers works against each other and the sound of the two playing together will be lacking in bass and sound phasey If you Suspect the sound is not right and you cannot see any markings on the wire try this simple test 1 Stand halfway between the loudspeakers 2 Play some music with the amplifier or radio set to Mono 3 Listen to the richness of the bass and the loudness of the sound 4 Turn off the amplifier and reverse the connections on one amplifier channel only 5 Repeat the listening test with the same volume control setting When the sound has a richer bass and is slightly louder the loudspeakers are working together or in phase SETTING THE BIPOLE DIPOLE MODE Each StageFront FX loudspeaker features a BIP
9. STAGE FRONT HOME THEATER SOLUTION Sam INSTALLATION GUIDE IW650FX IW770FX PROFESSIONAL QUALITY IN WALL SURROUND EFFECTS LOUDSPEAKERS Be UN 755 hN ECER JE D BY CONGRATULATIONS Thank you for choosing a superior StageFront Home Theater Solutions In Wall FX loudspeaker from Niles With proper installation and operation you should enjoy years of trouble free use Niles manufactures the industry s most complete line of custom installation components and accessories for audio video systems To see the complete Niles product assortment visit us on the Internet at www nilesaudio com TABLE OF CONTENTS Introduction 1 Features and Benefits 2 Installation Considerations 3 Finishing the Installation 8 Operation 12 Specifications 13 Limited Warranty 16 Warranty Registration Card 17 INTRODUCTION StageFront Home Theater Solutions loudspeakers are expressly designed for superior sonic quality in home theater applications Each model employs advanced technology components that extract the subtle nuances in recorded music or the thunderous action sound in a movie Models ending in FX are intended primarily for special effect placement Models ending in LCR are designed for front channel left center right placement or wherever a monopole design is required StageFront models are the perfect choice wherever quality of sound is the most important consider
10. akers are placed back corner walls of a home theater room near back corner walls of a home theater room with an L shaped sofa If your home theater system is capable of reproducing Dolby Surround EX consider using a second pair of StageFront FX loudspeakers on the side walls for an additional rear surround effect as shown in Figure 4 Ideally the side loudspeakers should be placed in line with the listening position with the BIPOLE DIPOLE controls set to DIPOLE For a more focused surround effect set the BIPOLE DIPOLE controls to BIPOLE If you like listening to music in surround modes which emulate concert hall acoustics consider using more than two surround loudspeakers to provide an extraordinary effect With StageFront loudspeakers it is easy to add another pair without affecting the decor of the room If the StageFront FX loudspeaker is being installed in existing construction please use the included cardboard template to mark your installation location Check for proper clearance within studs or any other obstructions before cutting the speaker opening If you are unsure of the correct installation techniques please consult your authorized Niles Audio dealer NOTE FOR THIS APPLICATION YOU WILL NEED TO USE A MORE POWERFUL AMPLIFIER THAN THE ONE BUILT INTO A TYPICAL SURROUND SOUND RECEIVER OR AMPLIFIER NILES MAKES A NUMBER OF SYSTEMS INTEGRATION AMPLIFIERS WITH PROPRIETARY FEATURES THAT MAKE THEM UNIQUELY SUITED TO ENHANCE
11. ation IW650FX Stock Number FG01331 IW770FX Stock Number FG01328 FEATURES AND BENEFITS TCC TALC CARBON CERAMIC FILLED WOOFER IW650FX only Extremely rigid to reduce breakup lower distortion and provide enhanced bass response DUAL SIDE FIRING TCC TALC CARBON CERAMIC FILLED SURROUND EFFECT DRIVERS IW650FX only Provide diffuse sound fields for optimum surround effects INTERLACED CARBON FIBER WOOFER WITH BUTYL RUBBER SURROUND IW770FX only Provide increased sound pressure levels and sustained high power output DUAL SIDE FIRING CARBON FIBER MIDRANGES WITH DUAL TETERON DOME TWEETERS IW770FX only Enable sustained high power playback and diffuse sound fields for optimum surround effects FORWARD FIRING FLUID COOLED TETERON DOME TWEETER Delivers ultra wide dispersion and silky smooth response 12 CONTROLLED DIPOLE BIPOLE RELAY Accommodates automated DVD Audio or Dolby surround sound effects FRONT MOUNTED DIPOLE BIPOLE SWITCH AND EFFECTS LEVEL CONTROL Enables fine tuning after installation CROSS BRACED PORTED CABINETS WITH INTEGRATED FRAME DESIGN Fits standard 2x4 construction and is easily retrofitted EPOXY COATED MICROPERF MAGNETIC GRILLE Provides an elegant yet unobtrusive appearance DOLBY DIGITAL READY StageFront Home Theater Solutions loudspeakers are expressly designed for superior sonic quality in home theater applications All models
12. d effects for either side or rear placement as well as various surround modes see SETTING THE BIPOLE DIPOLE MODE on page 11 Here are some recommended loudspeaker placement tips CONTINUED ON NEXT PAGE INSTALLATION CONSIDERATIONS CONTINUED Place the surround loudspeakers on a rear wall directly behind the listening position If possible try placing the loudspeakers nearer to the corners as shown in Figure 2 and 3 Set each BIPOLE DIPOLE switch to DIPOLE for reflected sound Moreover the adjoining walls will act as powerful reflectors to create even more reflections If you place the surround loudspeakers farther away from the listener the surround sound will dissipate requiring even more power from the surround sound channels If your sound system uses small less than 50 watts per channel surround amplifier for the rear loudspeakers be sure to place the loudspeakers within 5 to 8 feet of the listening location If you are using a larger more than 50 watts per channel surround amplifier you can mount the loudspeakers 10 to 15 feet away from the listening location and still achieve reasonably high volume levels In large or unusually shaped rooms this might be the only way to achieve a good effect Right 6 7 2 s EO poms Left N Figure 2 Loudspeakers are placed near Figure 3 Loudspe
13. er Name and Location OMiss Name OMr OMrs OMs Address City Telephone Please take a moment to fill out our warranty registration card The information helps us to get to know you better and develop the products you want Age O Under 25 O 25 34 O 35 44 O 45 54 O 55 amp over Income O Under 44 999 O 45 000 59 999 O 60 000 74 999 O 75 000 99 999 O 99 999 150 000 O 150 000 99 999 O 99 999 200 000 O Over 200 000 Occupation O Arts Entertainment O Business Owner O Engineer O Finance Accounting O General Office O Management O Professional O Sales Marketing O Student O Tradesperson Musical tastes Please check all that apply O Alternative O Classical O Country O Jazz O New Age O Popular O R amp B O Rock O Other How did you hear about Niles O Architect Developer O Custom Installer O Direct Mail O Friend Family O In Store Display O Interior Designer O Magazine Ad O Mail Order Catalog O Newspaper Ad O Product Brochure O Product Review O Retail Salesperson O Internets O Other What magazines do you read 1 2 3 Who will install the product O Custom Installer O Electrician O Friend O Myself Which factor s influenced the purchase of your Niles product Please check all that apply O Ease of Use O Price Value O Product Features Quality Durability O Reputation O Style Appeara
14. ether sandwiching the drywall so that the frame is absolutely flush with the wall surface There should be no gaps between the wall and the frame 7 Remove cardboard paint mask template from the box and keep for future potential use 8 Turn on the home theater receiver and calibrate all loudspeakers in the system according to the receiver manufacturer s instructions IMPORTANT DO NOT OVER TIGHTEN THE SCREWS OVER TIGHTENING THEM MAY MAKE THE GRILLE DIFFICULT TO INSTALL Figure 6 Connecting a loudspeaker wire to the terminals Rear View Figure 7 Installing unit into a wall CONTINUED ON NEXT PAGE 10 PAINTING THE GRILLE AND FRAME Each StageFront and LCR frame and grille may be painted without the need for primer For best results use a spray gun or airless sprayer thin the paint to prevent clogging of the grille holes and apply several light coats instead of one heavy one 1 Install loudspeaker into wall 2 Carefully peel adhesive covering strips off of paint mask and align over magnets on loudspeaker baffle Gently press into place 3 Paint the frame of the loudspeaker 4 Paint the grille separately from the loudspeaker frame 5 Reinstall grille after paint dries on all surfaces and the paint mask has been removed CHECKING LOUDSPEAKER PHA
15. exceed the specifications set forth by Dolby Laboratories for the accurate reproduction of Dolby Digital Encoded Sources INSTALLATION CONSIDERATIONS m Loudspeaker Baffle Dogs swivel 90 Mounting Screws Grille Figure 1 Mounting an IW770FX vertically into a wall CONTINUED ON NEXT PAGE INSTALLATION CONSIDERATIONS CONTINUED TOOLS AND PRECAUTIONS We recommend using the following tools to install an In Wall StageFront loudspeaker Electric drill with 1 4 and 1 2 inch drill bits and a 1 inch flat drill bit for drilling through studs Keyhole or drywall saw Stiff wire fish tape or glow rods for routing cables Phillips screwdriver set Cable ties Pencil Level Rubber gloves and protective eyewear Before starting the installation please observe the following precautions Turn off all system power before making any connections Always wear protective eyewear when using tools Make sure hands are clean before installation Wear gloves when working with fiberglass insulation RECOMMENDED AMPLIFIER POWER For satisfactory performance we recommend using a surround amplifier with a power rating of 15 to 125 watts Most loudspeakers are not damaged by large amplifiers but rather by small amplifiers If your system is playing loud music a small amplifier will run out of power very quickly and can create damaging clipping dis
16. nce O Warranty Doyou Own a House If yes how many square feet Own a Town House Condominium Co op O Rent an Apartment O Rent a House Are you interested in receiving literature on other Niles products O Yes O No Are there products capabilities that you would like to see introduced 17 ENGINEERED B Y R NILES NILES AUDIO CORPORATION 12331 SW 130 Street Miami FL 33186 1 800 BUY HIFI www nilesaudio com 2006 Niles Audio Corporation All Rights Reserved Niles and the Niles logo are registered trademarks of Niles Audio Corporation Stagefront Home Theater Solutions is a trademark of Niles Audio Corporation All other trademarks are the property of their respective owners DS00543A
17. tortions A more powerful amplifier will play at the same volume without distorting See OPERATION on page 12 for more information about amplifier clipping distortion LOUDSPEAKER WIRE Use 2 conductor loudspeaker wire when connecting loudspeakers to your receiver or amplifier For most applications we recommend using 16 gauge wire For wiring runs longer than 80 feet we recommend 14 gauge wire The spring loaded terminals will accommodate up to 12 gauge wire directly Larger sizes can be accommodated via pin connectors When running wire inside walls or ceilings use special jacketed cable CL 2 or CL 3 to protect the wire and to meet local electrical and fire codes In some areas conduit is also required For a trouble free installation low voltage wire such as loudspeaker wire must be run in accordance with the National Electrical Code and any applicable provisions of the local building code If you are unsure of the correct installation techniques wire jacket or type of conduit to use consult a professional audio video installer building contractor or the local building and inspection department TECH TIP Wire size is expressed by its AWG American Wire Gauge number the lower the number the larger the wire For example 12 AWG is physically larger than 14 AWG LOUDSPEAKER PLACEMENT NOTE THE STAGEFRONT FX LOUDSPEAKERS ARE DESIGNED FOR USE IN EFFECT CHANNEL APPLICATIONS FOR FRONT LEFT CENTER OR RIGHT CHANNEL NE
18. ust this control as follows The Diffuse Sound Level control adjusts the level between the side firing diffuse and front firing drivers Increase the level with this control for more ambiance A decrease with this control will yield a more direct sound OLE DiIp Pa Figure 8 The In Wall FX models STAGE FRONT 5 feature BIPOLE DIPOLE and Diffusion Der eg E Level controls INSTALLING THE GRILLE Starting at one corner carefully align the magnetic grille into the frame and slowly allow the magnets to attach Work around the grille edge ensuring that the grille stays within the frame When properly installed the edges of the grille will be flush in appearance with the frame OPERATION 12 LISTENING HIGHER VOLUMES Achieving a reasonable volume of sound in a large room requires more amplifier power than it does in a small room It is possible to turn the volume up so high that the amplifier runs out of power This creates clipping distortion which will make treble sound very harsh and unmusical When you hear harsh sounding treble from any good loudspeaker turn the volume down immediately Those harsh sounds are masking much more powerful ultra high frequency sound spikes which will quickly damage any fine loudspeaker You are much less likely to damage a loudspeaker driven by a large amplifier because it will be very loud before any clipping distortion is produced
Download Pdf Manuals
Related Search