Home

Nikon XX152-02-00 User's Manual

1. HOUSING CAMERA DRIVE ASSEMBLY A c t MOUNTING TAB BMer I Ft MOUNTING TAB PL Hd n m Hn vil EA I I ai e LU MORA gt I FAS Wi E folkene ils 77 N A ap SAFETY CORD LOWER DOME Figure 10 Pendant Mount Dome Final Installation 14 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Outdoor Pendant After all the cabling is complete push the SurveyorVFT camera mechanism straight up into the housing Align the 2 slots on the camera drive with the tabs in the enclosure being sure to match up the arrows on both the drive and in the enclosure Insert the camera drive into the enclosure until it snaps into place Note Assure that there is no extra slack in the cabling that will interfere with proper installation and operation Push any extra cabling up into the mount or pipe After the SurveyorVFT is in place the camera lens can be adjusted The camera position can be adjusted horizontally and vertically and rotation about the lens axis roll With the camera powered on and video displayed in a monitor turn the camera to point in the desired direction The tilt position can also be adjusted Loosen the two nuts if necessary on either side of the camera mounting frame use an open end 11 32 wrench Position the camera and retighten nuts The camera mounting bracket position can be adjusted relative to the closeness to the dome by loose
2. It has better electrical characteristics than polyethylene and resists flames sunlight and most solvents but is more vulnerable to moisture Cable Types The most commonly used cable types are point to point unshielded twisted pair wire stranded or solid unjacketed 24 gauge or thicker They can be category 2 3 4 or 5 The video signal may co exist in the same wire bundle as other video telephone data control signals or low voltage power It is also acceptable to run the signal adjacent to fluorescent lights or other power sources in accordance with National Electrical Code local and other safety requirements Make sure the pair of wires carrying the video signal is sent as a twisted pair the blue white white blue wires twisted together as a pair not a split pair blue white conductor part of one pair orange white conductor part of another pair Choose a Belden or equivalent cable type by referring to the characteristics and maximum distances listed below The characteristics of the cables in the Tables should be used as a guideline when cables other than Belden are used Materials and construction must follow the guidelines above Wire resistance may be measured with an ohmmeter by shorting the two conductors together at the far end and measuring the loop resistance out and back Compare your readings to the following chart Wire Distances Wire Gauge AWG Distance ft m 18
3. floppy drives CD R W drives and any and all archive media warranted for 18 months All other parts warranted for 3 years from date of original retail purchase Normal Use excludes prolonged use of lens and pan and tilt motors gear heads and gears due to continuous use of autopan or tour modes of operation Such continuous operation is outside the scope of this warranty NO OT GR Date of retail purchase is the date original end user takes possession of the equipment or at the sole discretion of the Company the date the equipment first becomes operational by the original end user The sole remedy under this Warranty is that defective equipment be repaired or at the Company s option replaced at Company repair centers provided the equipment has been authorized for return by the Company and the return shipment is prepaid in accordance with policy The Company will not be obligated to repair or replace equipment showing abuse or damage or to parts which in the judgment of the Company are not defective or any equipment which may have been tampered with altered misused or been subject to unauthorized repair Software supplied either separately or in hardware is furnished on an As Is basis Vicon does not warrant that such software shall be error bug free Software support via telephone if provided at no cost may be discontinued at any time without notice at Vicon s sole discretion Vicon reserves the right to make
4. retinent aioe eta ede eta ue e nta lad 4 Mounting from Above the Ceilirig trot ect rte take ete nae edda den dec decent 5 Optional Independent Support sse enne eret nete nn nennen rrt entere nn nes 6 Indoor Pendant 2 x ih Rer rt eie ER Hae hee A ERR ee Ee el ee ve ee aes 7 Qutdoor Pendant ebat teer ee en een te ace dines 8 Gable Connections RT M 8 Coaxial Video Cable acct n aet ie bue tet dear akse lat 8 Camera Power Contiectioris entire n nitet let bise t ie ad dete olii htt eeu ned EE Adde tia Peds 9 ILES Sube C 10 Gamera Synchronization E 10 AutolrisAdjustments sureste englene 10 Final Installatiori orent d ede kamerat 12 Disassembly aaen anaE anaE e A AAA ELI ELIMEEEEE 16 A A A E E E 17 Manenance 5 17 Care and Cleaning of Lower DoOme vrnnnnavnnnnnnnvnnnnnnnnvnnnnnnnvennnnnnvnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnnnennnnnnnnr 17 Fuse Replacemient edocet rette n 17 Shipping Instructions ceci oC Com SE IA Le D UTI ORI PA IIDMIIDR C EPIICI LAND OLI RPPMIDIOE 18 Reierence 4 19 Technical Information uses I DIEM EMI AME 21 XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Contents e i Quick Installation CONDUIT FITTING FLEXIBLE CONDUIT A CABLES WITHOUT FLEXIBLE CONDUIT Cut a 7 3 8 inch 187 mm
5. 20 22 24 250 76 3Q 50 80 130 315 96 40 60 100 160 397 121 50 80 130 210 500 152 7Q 10Q 170 260 630 192 80 130 210 330 794 242 100 160 260 410 1000 305 130 200 330 520 1260 384 160 250 420 660 1587 484 210 320 520 830 2000 610 260 400 660 1040 Note All quoted distance specifications include any coaxial cable in the run It is recommended that the wire distance be measured to ensure that the capability of the product is correct Recommended Unshielded Twisted Pair Cable Type Cable Type Insulation Material Conductor Type Resistance ohms AWG Twisted Pairs Belden1721X 24 Solid Polyethylene Bare Copper 20 e Reference XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Technical Information ELECTRICAL Input Voltage Current Power Consumption Heat Equivalent heat 24 VAC 120 Indoor 0 4 A Outdoor 1 1 A Indoor 10 W Outdoor 27 W Indoor 0 6 btu min 0 14 kg cal min Outdoor 1 5 btu min 0 4 kg cal min Note These figures represent the conversion of 100 of the electrical energy to Actual percentage of heat generated will be less and will vary from product to product These figures are provided as an aid in determining the extent of cooling required for an installation Maximum Power Cable Distance Wire Size AWG Maximum Distance ft m RE Indoor Outdoor 20 600 183 220 67 18 938 286 344 105 16 1500 457 550 1
6. CONDUIT FITTING SENET CEILING Remove conduit fitting and install strain relief fitting LL SHROUD FOR CABLE USE WITH FLEXIBLE CONDUIT CACHES NOUT Route 12 inches 305 mm of conduit cables through conduit fitting CONDUIT OR STRAIN RELIEF FITTING CAMERA MECHANISM inside enclosure CLIP a ones SAFETYCORD y i FOR CABLE USE WITH Cut a 7 3 8 inch 187 mm diameter STRAIN RELIEF FITTING hole in ceiling Pp Route 12 inches 305 mm of conduit J y cables through strain relief fitting Tighten 2 strain relief fitting screws e P d FOR CABLE USE WITH P FLEXIBLE CONDUIT LOWER DOME Insert end of flexible conduit pipe into conduit fitting and tighten clamp screw i i i i i i i i i i 3 Insert the clip of the safety cord on the lower dome into the hole on the enclosure Lift lower dome up to unit and align the molded tabs with the recesses on the inner enclosure Lower dome snaps into place Refer to the Maintenance Section for lower dome handling Attach the male BNC connector on the video cable to the mating connector on the PC board coax version or connect twisted pair wire to screw terminal UTP version Press power cable connector onto board connector PRINTED CIRCUIT BOARD nn BNC VIDEO CONNECTOR TWISTED PAIR SCREW TERMINAL VIDEO CONNECTOR POWER SCREW TERMINAL BLOCK In Ceiling Access to Ceiling XX152 02 00 Rev 1
7. Refer to Figure 2 8 Route each cable from the inside top of the housing down over to its mating connector on the camera PC board Add 1 in 25 mm of extra length to each cable for termination if not previously terminated and cut them The approximate length of each cable should be 14 15 in 356 381 mm Continue with the section on Cable Connections Cable Connections Both power and video connections are made to the integral printed circuit board PC board on the camera mechanism The PC board provides a board mounted BNC connector for coaxial or a screw terminal for twisted pair video and a removable two position screw terminal connector for camera power Refer to Figure 4 when performing these connections Refer to Cable Recommendations in the Reference section There is also a provision for adjusting the focus with the auxiliary video output port provided on the underside of the camera mechanism This adjustment should be performed during installation Refer to Figure 6 Coaxial Video Cable Attach the male BNC connector on the video cable to the mating BNC connector on the PC board Twisted Pair Video Cable For the models using the twisted pair video connection use the twisted pair video wire connector as shown in Figure 4 Strip off approximately 0 25 in 6 mm of insulation from each individual wire Attach each wire to the screw terminal on the PC board Pin 1 is for Video and Pin 2 is Ground Pin 3 is Not Used Refer to
8. black ABS plastic shell It has a 1 4 in 35 6 mm slotted opening for the camera This shroud conceals the position of the camera and snaps onto the camera drive Lower Dome The lower dome is an assembly comprised of a 5 9 inch 150 mm diameter acrylic plastic shell a trim ring and a safety cord Lower domes for indoor versions come in a choice of smoked chrome or gold finishes Standard outdoor lower domes are clear and use 4 screws for additional support All lower domes are anchored to the enclosure by the safety cord Refer to the Maintenance section for care Housing The housing for the SurveyorVFT fixed indoor pendant configurations is a molded plastic protective cover for the camera mechanism outdoor pendant configurations have a die cast aluminum housing with a sunshield The housing has a 1 5 inch NPT pipe flange mount In addition the housing is equipped with a safety cord and clip that is used to suspend the camera drive during installation Another safety cord connects the lower dome to the housing Sunshield A sunshield pre installed over the housing used on the outdoor pendant version is for radiation sun blocking protection Aca UTION For any environment subject to moisture use the outdoor pendant model XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 3 Mounting the Unit In Ceiling Mounting The SurveyorVFT fixed dome rests on the ceiling material and occupies the space between the lower ceiling
9. changes to its software in any of its products at any time and without notice This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods including any warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies available to the Purchaser No one is authorized to assume any liability on behalf of the Company or impose any obligations on it in connection with the sale of any Goods other than that which is specified above In no event will the Company be liable for indirect special incidental consequential or other damages whether arising from interrupted equipment operation loss of data replacement of equipment or software costs or repairs undertaken by the Purchaser or other causes This warranty applies to all sales made by the Company or its dealers and shall be governed by the laws of New York State without regard to its conflict of laws principles This Warranty shall be enforceable against the Company only in the courts located in the State of New York The form of this Warranty is effective August 2 2004 THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT THIS WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE COMPANY S WEBSITE WWW VICON CCTV COM IN THAT EVENT THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY Vicon Part Number 8006 9010 03 01 Rev
10. diameter gimme hole in ceiling Feed flexible conduit Fd pipe or cables through hole n CEILING _ LZ 3 FLEXIBLE CONDUIT gt OR CABLES Lift enclosure up through ceiling ye hole turn and tighten flipper screws FOR CABLE USE WITHOUT s e FLEXIBLE CONDUIT i Remove enclosure top cover and conduit fitting Install strain relief fitting and re install top cover Connect the enclosure s safety cord clip to the tab in the camera mechanism Allow mechanism to hang from enclosure STRAIN RELIEF i d SAFETY CORD FITTING ua CLIP FLIPPERS NM FLIPPER zx bi SCREWS fi FOR CABLE USE WITH FLEXIBLE CONDUIT Hold enclosure up to ceiling and route 12 inches 305 mm of conduit cables through conduit fitting g FOR CABLE USE WITHOUT FLEXIBLE CONDUTT ud CLIP x Hold enclosure up to ceiling and SAFETY CORD Ez k route 12 inches 305 mm of conduit 5 A Align the two slots on the enclosure cables through conduit fitting we Tighten 2 strain relief fitting screws EEE _ _ K E A with the two tabs on the camera mechanism Matching up the arrows we A E aL FOR CABLE USE WITH Mid slide the mechanism into the enclosure FLEXIBLE CONDUIT ee ER until it snaps securley into place LOWER DOME DO NOT APPLY POWER YET Insert end of flexible conduit pipe into Make any necessary camera lens conduit fitting and tighten clamp screw adjustmen
11. or a 1 5 in vertical pipe with an appropriate coupling The outdoor version includes a sunshield heater and weather protection Be sure the area around the selected location is clear of obstacles such as steel beams headers pipes electrical wiring etc that would interfere with mounting Video sync and power cables must be routed to the location Note The standard 1 5 inch pipe referred to in this manual has the actual dimensions of outside diameter 1 9 in 48 3 mm inside diameter 1 61 in 40 9 mm wall thickness 0 145 in 3 37 mm minimum ANSI standard grade thickness 1 Install the mount in accordance with the installation manual included with the mount or prepare the vertical 1 5 in NPT pipe 2 Feed all necessary cables through the back of the mount or out the end of the 1 5 in NPT pipe 15 in 381 mm in length Apply the provided anti seize lubricant to the first 2 3 unpainted threads of the housing Lift the sunshield housing up to the mount and feed the cables through its top opening Place the housing onto the 1 5 in pipe and screw clockwise looking up at the housing When it becomes snug turn it an additional quarter turn Verify that each cable drops from the pipe opening at least 15 in 381 mm in length Lift the SurveyorVFT camera mechanism up to the housing sunshield and attach the housing s safety cord clip to the camera mechanism s tab Allow the camera mechanism to hang from the housing
12. wider allowing more light Autoiris control is DIP switch selectable 10 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Day Night Potentiometer located on top of back board AUTOIRIS ADJUSTMENT POTENTIOMETER ELC INT AGC BLC V Phase VR1 Potentiometer located on bottom of back board The Camera Lens assembly must be installed so that the markings on the PCB can be read left to right This ensures that the video display is oriented correctly Figure 5 Potentiometer DIP Switch Location Camera Switch Settings ELC INT AGC BLC Bal zs IN OFF ALC LL Day Night Setting ON OFF Figure 6 DIP Switch Settings XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 11 Final Installation In Ceiling After all cabling is complete if not previously done connect the enclosure s safety cord clip to the tab in the camera mechanism to allow the mechanism to hang from the enclosure Align the 2 slots on the camera mechanism with the tabs in the enclosure being sure to match up the arrows on both the drive and in the enclosure Insert the camera mechanism into the enclosure until it snaps into place Refer to Figure 9 Note Assure that there is no extra slack in the cabling that will interfere with proper installation and operation Push any extra cabling up into the ceiling The camera and lens can now be adjusted Refer to Figure 7 The camera position can be adju
13. 00 feet RG 11 U 8213 9847 811 4811 14 Solid BC_ BC braid 95 2 6 8 5 RG 6 U 9248 9804C 806 4806 18 Solid BC Foil 61 TC 7 5 24 6 braid 100 RG 59 U 8281 9803 20 Solid BC_ 2 TC braids 96 9 9 32 5 RG 59 U 9259 pe 3 22 Stranded BC braid 95 15 0 49 BC RG 59 U 9659 7 7 22 Stranded BC braid 95 15 0 49 BC Picture Quality vs Cable Length Maximum Picture Quality Cable Run ft m RG 59U RGU RG fUU 2400 750 820 250 1600 500 For longer cable runs refer to the Product Specifications for Video Amplifiers 1 5 inch Pipe Designation The standard 1 5 inch pipe referred to in this manual has actual dimensions of Outside diameter 1 9 inches 48 3 mm Inside diameter 1 61 inches 40 9 mm Wall thickness 0 145 inches 3 37 mm minimum ANSI standard grade thickness XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Reference e 19 Twisted Pair Cable Acaution Careful selection of the proper cable is essential to obtain the best performance from this equipment Vicon assumes no responsibility for poor performance when cables other than those recommended are installed Materials Use a pure copper stranded or solid conductor with or without a tin plating to obtain a low DC resistance Do not use cable with either steel or aluminum stranded conductor because these do not transfer signals effectively for long distances The preferred insulation is Polyvinyl chloride PVC
14. 1204 SurveyorVFT Fixed Camera Dome Height Adjustment Nut Height Adjustment Slot Figure 8 Camera Mounting Bracket Adjustment 2 6 6 mm Version Shown Insert the clip of the safety cord on the lower dome into the hole in the enclosure Refer to label in the enclosure Lift the lower dome up to the SurveyorVFT and align the molded tabs on the lower dome with the recesses on the inner enclosure Press the lower dome into the SurveyorVFT and verify that it snaps into place on both sides The upper edge of the lower dome should be flush with the ceiling plane Refer to Figure 9 CAMERA DRIVE ASSEMBLY T NOT d INDO LOWER DOME Figure 9 In Ceiling Mount Final Installation XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 13 Indoor Pendant After all the cabling is complete push the SurveyorVFT camera mechanism straight up into the housing Align the 2 slots on the camera mechanism with the tabs in the enclosure being sure to match up the arrows on both the mechanism and in the enclosure Insert the camera mechanism into the enclosure until it snaps into place Refer to Figure 10 Note Assure that there is no extra slack in the cabling that will interfere with proper installation and operation Push any extra cabling up into the mount or pipe After the SurveyorVFT is in place the camera lens can be adjusted The camera position can be adjusted horizontally and vertically and rotation about the le
15. 204 SurveyorVFT Fixed Camera Dome Quick Installation e iii Install mount or prepare a vertical MOUNT mn cm 1 1 2 INCH PIPE 1 5 inch NPT pipe Feed all cables eee at least 15 inches 381 mm through pipe opening and into top of housing CABLES M Screw housing clockwise onto mount When snug turn an additional quarter tum CABLE ACCESS PLUG HOLE HOUSING 17 HEBER SAFETY CORD SAFETY CORD CLIP a 1 Attach housing s safety cord to tab on i m s AMERA MECHANISM Ss camera mechanism Allow the mechanism to hang from housing Route each cable down to the cable clamp on PC board SM Align the two slots on the housing with the two tabs on the camera mechanism Matching up the arrows slide the mechanism into the housing until it snaps securley into place DO NOT APPLY POWER YET Make any necessary camera lens 1 adjustments SAFETY CORD 7 Insert the clip of the safety cord on the lower dome into the hole on the enclosure Lift lower seeesonsnosnsneannsnnenesensenssceseesesenesssesnsnseensanesessensesseesesseneseennssnneesennessseened JOME UP tO unit and align the molded tabs LOWER DOME with the recesses on the inner housing Lower dome snaps into place Refer to the Maintenance Section for lower dome handling S Attach the male BNC connector on the video cable to the mating connector on the PC board coax version or connect twiste
16. 68 14 2400 732 880 268 12 3750 1143 1375 419 Connectors Power 2 pin removable screw terminal P8 Fuse Radio Frequency Emission Rating CAMERA LENS Specifications OPERATIONAL Tilt and Horizontal Adjustment MECHANICAL Application Mounting Video BNC coax or screw terminal twisted pair Indoor 0 5 A 250 V 5x20 mm slo blo Outdoor 1 6 A 250 V 5x20 mm slo blo additional FCC Class A Refer to Table 3 3 axis adjustment pan 360 tilt 95 and roll lens may be rotated on its axis 360 Indoor and outdoor models In ceiling and pendant models XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Technical Information e 21 Dimensions In Ceiling Height 9 7 in 246 mm Total Diameter 7 1 in 180 mm Dome Diameter 5 9 in 150 mm Indoor Pendant Height 10 0 in 254 mm Total Diameter 8 0 in 203 mm Dome Diameter 5 9 in 150 mm Outdoor Pendant Height 10 3 in 236 mm Total Diameter 9 0 in 262 mm Dome Diameter 5 9 in 150 mm Weight Approximately 2 5 Ib 1 1 kg Construction Plastic aluminum and steel Finish Painted black enclosure off white housing sunshield smoked gray tint indoor or clear outdoor lower dome ENVIRONMENTAL Operating Temperature Range Indoor 35 to 122 F 2 to 50 C Outdoor 40 to 122 F 40 to 50 C Operating Humidity Indoor Up to 90 relative noncondensing Outdoor Up to 100 relative noncondensin
17. 804 XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome e 25 Vicon Industries Inc Corporate Headquarters 89 Arkay Drive Hauppauge New York 11788 631 952 CCTV 2288 800 645 9116 Fax 631 951 CCTV 2288 lnfofax 800 287 1207 Vicon Europe Headquarters Brunel Way Fareham PO15 5TX United Kingdom 44 0 1489 566300 Fax 44 0 1489 566322 Brussels Office Planet II Unit E Leuvensesteenweg 542 B 1930 Zaventem Belgium 32 2 712 8780 Fax 32 2 712 8781 Far East Office Unit 5 17 F Metropole Square 8 On Yiu Street Shatin New Territories Hong Kong 852 2145 7118 Fax 852 2145 7117 Internet Address www vicon cctv com
18. Figure 4 Refer to the instructions supplied with the receiver for those connections 8 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Camera Power Connections Note Vicon systems and components like most electronic equipment require a clean stable power source Voltage irregularities such as surges drops and interruptions can affect the operation of your equipment and in severe cases damage certain components Vicon strongly recommends the use of line conditioners voltage regulators and uninterruptible power supply UPS systems Power is connected through a two position detachable screw terminal connector on the PC board P8 Refer to Figure 4 Refer to Table 2 for the input power connections 1 Find the detachable power cable connector supplied on the PC board 2 Strip approximately 1 in 25 mm of insulation off power cables Then strip off approximately 0 25 in 6 mm of insulation off each individual wire Attach the camera power cables to the connector according to Table 2 3 Press the cable connector onto the board connector The connector is keyed to prevent incorrect installation The camera is shipped prepared for 24 VAC PRINTED CIRCUIT BOARD BNC VIDEO CONNECTOR on Coaxial version only POWER SCREW TERMINAL BLOCK Twisted Pair Screw Terminal ie Video Connector on Twisted Pair version only 24 VAC Return 24 VAC Input Figure 4 Camera Lens PC Board Table 2 Cam
19. Simply add a T to the model number and a 40 to the product code ex SVFT C266M T 8725 40 SVFT C266M TC 8725 41 XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Introduction e 1 UTP Receivers V212 NVT 7631 Receiver converts UTP video to composite up to 500 ft from transmitter V213 NVT 6518 Receiver converts UTP video to composite up to 1000 ft from transmitter Receiver converts UTP video to composite up to 3000 ft from transmitter does not support Vicoax systems each transmitter each transmitter does not support Vicoax systems Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory It is the carrier s responsibility to deliver the equipment in the same condition as it left the factory Inspection for Visible Damage Immediately inspect the cartons upon delivery Make a note of any visible damage on all copies of the carrier s freight bill Make sure the carrier s agent the person making the delivery signs the note on all copies of the bill If the agent does not have claim forms contact the carrier s office Inspection for Concealed Damage As soon as possible after delivery unpack the unit and inspect it for concealed damage Do not discard the carton or packing materials If the unit is damaged contact the carrier immediately and request forms for filing a damage claim Make arrangements for a representative of the carrier to inspect the damaged equip
20. XX152 02 00 SURVEYSRVFT FIXED CAMERA DOME C uopgejejsu Vicon Industries Inc does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation This system has not been designed to be used in life critical situations and must not be used for this purpose Copyright 2004 Vicon Industries Inc All rights reserved Product specifications subject to change without notice Vicon and its logo are registered trademarks of Vicon Industries Inc lt lenuel uoneJodo VICON INDUSTRIES INC 89 ARKAY DRIVE HAUPPAUGE NEW YORK 11788 TEL 631 952 CCTV 2288 FAX 631 951 CCTV 2288 TOLL FREE 800 645 9116 24 Hour Technical Support 800 34 VICON 800 348 4266 UK 44 0 1489 566300 WEB www vicon cctv com A us O Vicon part number 8009 8152 02 00 Rev 1204 Section 3 Dear Valued Customer Thank you for selecting Vicon systems and products for your video needs Since Vicon s beginning in 1967 our only business has been the design engineering and production of the highest quality video systems and equipment for use in a wide variety of security safety control surveillance and communication applications We stand behind the quality and dependability of every product with an industry leading Beneficial Use warranty If you are not satisfied with a Vicon product or service I would lik
21. al Line lock 1 60 1 100 000 SVFT P550M C 2 1 interlace at 40 IRE DIP switch 1 50 PAL gt 48 dB AGC off NTSC PAL 1 6 selectable Day 0 07 0 8 SVFT W266DNA 1 4 CCD Color Color 480 Night 0 0009 Internal Line lock 1 60 1 100 000 gt 48 dB SVFT W266DNA C 2 1 interlace Mono 580 0 01 DIP switch 1 50 PAL AGC off NTSC PAL at 40 IRE selectable f 1 6 1 3 ExView SVFT W266A CCD 0 07 0 8 Internal Line lock 1 60 1 100 000 gt 48 dB SVFT W266A C 2 1 interlace Color 480 at 40 IRE DIP switch 1 50 PAL AGC off NTSC PAL f 1 6 selectable 1 3 CCD Internal Line lock SVFT W550A 2 1 interlace Color 480 0 07 0 8 DIP switch 1 60 1 100 000 gt 48 dB AGC off SVFT W550A C NTSC PAL at 40 IRE selectable 1 50 PAL f 1 6 XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Technical Information e 23 24 e Technical Information Lens Specifications Model Focal Length Field of View mm Horizontal Vertical SVFT C266M 2 6 6 varifocal SVFT C266M C with manual iris 106 47 6 78 2 35 8 SVFT C266A 2 6 6 varifocal SVFT C266A C with autoiris 106 47 6 78 2 35 8 SVFT C550M 5 50 varifocal SVFT C550M C with manual iris 51 8 5 6 39 2 4 3 SVFT P266M 2 6 6 varifocal SVFT P266M C with manual iris 106 47 6 78 2 35 8 SVFT P266A 2 6 6 varifocal SVFT P266A C with autoiris 106 47 6 78 2 35 8 SVFT P550M 5 50 va
22. and upper building frame There are two methods of installation The first method can be used for ceilings with no access to the space above as in a typical hard material ceiling The second method is used for a ceiling with access as in the case of a dropped ceiling metal grid type All mounting hardware is provided Refer to the section on Optional Independent Support for installations requiring additional support most commonly a dropped ceiling Using the Provided Scribe A small metal scribe is provided to assist in marking an accurate hole size in a ceiling tile Use it as follows 1 Place the ceiling tile on a large flat surface face up 2 Measure and make a small mark at position A from any corner 11 9 in 302 mm Refer to Figure 1 3 Measure and make a small mark at position B 8 2 in 208 mm placing the scribe as perpendicular to the A edge as possible 4 Place the scribe across B and C Rotate the scribe around center C for a full turn 5 Cut out the circle using a sharp tool on the scribed line oe SCRIBE le 11 9 in ed Te 302 mm t amp Figure 1 Use of the Scribe Mounting from Below the Ceiling Use this method of installation if there is no access to the space above The ceiling material must provide suitable strength to support the weight of the SurveyorVFT fixed dome with the two flippers on the enclosure Be sure the area around the selected location is clear of obstacles
23. ce 20 Replacement Parts Use only Vicon specified replacement parts or an approved equivalent to prevent unit damage and injury 21 Safety Check Request safety checks to be performed following repair or maintenance to verify proper operation 22 ESD Precaution Take all normal electrostatic discharge precautions to avoid component damage during installation and operation 23 For 230 VAC Devices When the disconnect device is not incorporated in the equipment or when the plug on the power supply is intended to serve as the disconnect device follow the guidelines below a For permanently connected 230 VAC units a readily accessible disconnect device must be incorporated into the site wiring b For 230 VAC units with a plug the outlet must be installed near the unit and be easily accessible Contents Quick Installation LN M ii Introduction pan 1 InstallatlOl A a 2 Unpacking and Inspectlon rene diran 2 Inspection for Visible Darmage coiere te eta ter dest peat sees pe dende de tannete 2 Inspection for Concealed Damage rtt dte c tee tere aids 2 SurveyorVFT Fixed Dome Components eese eene eene nnne nennen nnn innen nnne nennen nnn 3 Mounting the Unit CELL 4 In Ceiling Mounting iacet eee A ee ear GE euet dee din 4 Using the Provided Scribe i t n ae etat e tege e are dee dett eee aeree dd 4 Mounting from Below the Ceiling
24. d location is clear of obstacles such as steel beams headers pipes electrical wiring etc that would interfere with mounting Video sync and power cables must be routed to the location 1 Install the mount in accordance with the installation manual included with the mount or prepare the vertical 1 5 in NPT pipe 2 Feed all necessary cables through the back of the mount or out the end of the 1 5 in NPT pipe approximately 15 in 381 mm in length Lift the housing up to the mount or pipe and feed the cables through its top opening Place the housing onto the 1 5 in pipe and screw clockwise looking up at the housing When it becomes snug turn it an additional quarter turn Verify that each cable drops from the pipe opening at least 15 in 381 mm in length Lift the camera mechanism up to the housing and attach the housing s safety cord clip to the camera mechanism s tab Allow the SurveyorVFT mechanism to hang from the housing Refer to Figure 2 7 Route each cable from the inside top of the housing down over to its mating connector on the camera PC board Add 1 in 25 mm of extra length to each cable for termination if not previously terminated and cut them The approximate length of each cable should be 14 15 in 356 381 mm Continue with the section on Cable Connections XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 7 Outdoor Pendant The outdoor pendant model mounts on a Vicon mount
25. d pair wire to screw terminal UTP version Press power cable connector onto board connector Push any excess cable up into pipe opening to ensure that it does not get wedged between the housing and the mechanism PRINTED CIRCUIT BOARD BNC VIDEO CONNECTOR POWER SCREW TERMINAL BLOCK TWISTED PAIR SCREW TERMINAL VIDEO CONNECTOR Pendant Indoor iv e Quick Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Install mount or prepare a vertical MOUNT 1 1 2 INCH PIPE 1 5 inch NPT pipe Feed all cables EEE EE ERA at least 15 inches 381 mm through pipe opening and into top of housing CABLES Apply anti seize provided onto threads CABLE ACCESS jenes Of housing Screw housing clockwise onto mount When snug turn an PLUG HOLE HOUSING additional quarter turn NM SAFETY CORD SAFETY CORD CLIP Attach housing s safety cord to tab on Trenes Camera mechanism Allow the mechanism to hang from housing Route each cable un MERE MECHANISM down to the cable clamp on PC board vaseenvnrsveversnnnerenvnnsevnnnrnvnnernevnvsenennsenrg Align the two slots on the housing with the two tabs on the camera mechanism Matching up the arrows s slide the mechanism into the housing until it snaps securely into place CLIP DO NOT APPLY POWER YET Make any necessary camera lens 2 e adjustments SAFETY CORD 5 5 CAPTIVE R cpm os MOUNTING Insert the clip o
26. e to know Your complete satisfaction is the mission of every Vicon employee Sincerely ra Kenneth M Darby President FCC Notice Note Complies with Federal Communications Commission Rules amp Regulations Part 15 Subpart B for a Class A digital device WARNING This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instruction may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules which are designed to provide reasonable protection against such interference in a commercial installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient the receiving antenna e Relocate the equipment with respect to the receiver Relocate the equipment away from the receiver Plug the equipment into a different electrical outlet so that the equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television tech
27. era Power Connections Pin Number Function 24 VAC Input 24 VAC Return XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 9 DIP Switch Settings There is a DIP switch on the front camera board that allows the selection of Switch 1 ALC OFF or ELC ON Switch 2 Internal Crystal Synchronization ON or Line Lock OFF Switch 3 AGC ON or OFF Switch 4 BLC ON or OFF ALC setting is for external autoiris and ELC setting is for internal autoiris The day night camera includes a switch to select having the day night feature turned ON or OFF If day night is turned ON at a low light level the camera changes to monochrome mode and the resolution and sensitivity increase Refer to Figures 5 and 6 for the location and setting of the switches See Table 3 for camera and lens specifications There are two potentiometers on the camera VR1 on the back board is for V phase adjustment VR1 on the top board is for autoiris adjustment Refer to Figure 5 Camera Synchronization If there is more than one unit in a system the cameras have to be synchronized to ensure there is no roll of video If the camera will be used in a line lock video application the camera interface board is already set in line lock mode by default Camera synchronization is DIP switch selectable line locked or internal The use of line locking synchronization using a V phase potentiometer pot is typically included in video equipment req
28. f the safety cord on the lower i SCREWS 4 dome into the hole on the housing Lift lower dome up to unit and align the molded tabs Peones with the recesses on the inner housing Lower dome snaps into place Secure with LOWER DOME captive mounting screws Refer to the Maintenance Section for lower dome handling Attach the male BNC connector on the video cable to the mating connector on the PC board coax version or connect twisted pair wire to screw terminal UTP version Press power cable connector onto board connector Push any excess cable up into pipe opening to ensure that it does not get wedged between the housing and the mechanism BNC VIDEO CONNECTOR POWER SCREW TERMINAL BLOCK TWISTED PAIR SCREW TERMINAL VIDEO CONNECTOR Pendant Outdoor XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Quick Installation e v Introduction The information in this manual covers the installation operation and maintenance of the SurveyorVFT Series of Fixed Camera Domes This unit should only be installed by a qualified technician using approved materials in accordance with national state and local wiring codes Read this manual through completely before attempting installation The SurveyorVFT Series of Fixed Camera Domes offers a compact domed housing incorporating a fixed camera and lens combination The camera domes are available for indoor in ceiling and pendant mounting configurations and outdoor pendant mounting confi
29. g Storage Temperature Range 40 to 150 F 40 to 65 C Storage Humidity Up to 90 relative noncondensing Wind Load Outdoor heavy rain or snow driven by winds up to 80 mph 22 e Technical Information XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Table 3 Camera Specifications Model Image Color Resolution Sensitivity Synchronization Electronic Iris Signal to Noise Device Mono TV lines fc lux sec Ratio SVFT C266M 1 3 CCD Color 480 0 07 0 8 Internal Line lock 1 60 1 100 000 SVFT C266M C 2 1 interlace at 40 IRE DIP switch 1 50 PAL gt 48 dB AGC off NTSC PAL f 1 6 selectable SVFT C266A 1 3 CCD Color 480 0 07 0 8 Internal Line lock 1 60 1 100 000 SVFT C266A C 2 1 interlace at 40 IRE DIP switch 1 50 PAL gt 48 dB AGC off NTSC PAL f 1 6 selectable SVFT C550M 1 3 CCD Color 480 0 07 0 8 Internal Line lock 1 60 1 100 000 gt 48 dB AGC off SVFT C550M C 2 1 interlace at 40 IRE DIP switch 1 50 PAL NTSC PAL 1 6 selectable SVFT P266M 1 3 CCD Color 480 0 07 0 8 Internal Line lock 1 60 1 100 000 SVFT P266M C 2 1 interlace at 40 IRE DIP switch 1 50 PAL gt 48 dB AGC off NTSC PAL f 1 6 selectable SVFT P266A 1 3 CCD Color 480 0 07 0 8 Internal Line lock 1 60 1 100 000 SVFT P266A C 2 1 interlace at 40 IRE DIP switch 1 50 PAL gt 48 dB AGC off NTSC PAL f 1 6 selectable SVFT P550M 1 3 CCD Color 480 0 07 0 8 Intern
30. gurations Each model has a corresponding version that transmits video over twisted pair UTP An appropriate receiver is required for these models There is a choice of high resolution color or day night cameras with a 2 6 6 mm or 5 50 mm varifocal lens some models offer autoiris lenses A smoked lower dome is included on indoor models a clear dome is used on outdoor versions Refer to Table 1 for model numbers and descriptions The camera position has a unique 3 axis adjustment allowing for adjustment of pan tilt and rotation about the lens axis roll for any angle of view required The varifocal lens allows for lens adjustment capability and autoiris adjustment is available by a potentiometer Cameras accept 24 VAC and also feature line lock capability SurveyorVFT Fixed Camera Dome series meets FCC requirements for a Class A device Table 1 Models Product Codes and Descriptions SVFT C266M 8725 8725 01 In ceiling 1 3 in ExView high resolution color camera with isolated SVFT C266M C power input and 2 6 6 mm manual varifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT C266A 8726 8726 01 In ceiling 1 3 in ExView high resolution color camera with isolated SVFT C266A C power input and 2 6 6 mm autoiris varifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT C550M 8727 8727 01 In ceiling 1 3 in ExView high resolution color camera and 5 50 mm SVFT C550M C manual var
31. ifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT P266M 8730 8730 01 Indoor Pendant 1 3 in ExView high resolution color camera with SVFT P266M C isolated power input and 2 6 6 mm manual varifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT P266A 8731 8731 01 Indoor Pendant 1 3 in ExView high resolution color camera with SVFT P266A C isolated power input and 2 6 6 mm autoiris varifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT P550M 8732 8732 01 Indoor Pendant 1 3 in ExView high resolution color camera and 5 SVFT P550M C 50 mm manual varifocal lens 24 VAC smoked lower dome coaxial video transmission NTSC PAL SVFT W266DNA 8735 8735 01 Outdoor Pendant 1 4 in high resolution day night color camera with SVFT W266DNA C isolated power input and 2 6 6 mm autoiris varifocal lens 24 VAC clear lower dome coaxial video transmission NTSC PAL SVFT W266A 8736 8736 01 Outdoor Pendant 1 3 in ExView high resolution color camera with SVFT W266A C isolated power input and 2 6 6 mm autoiris varifocal lens 24 VAC clear lower dome coaxial video transmission NTSC PAL SVFT W550A 8737 8737 01 Outdoor Pendant ExView 1 3 in high resolution color camera and SVFT W550A C 5 50 mm autoiris varifocal lens 24 VAC clear lower dome coaxial video transmission NTSC PAL Note Each model is also available in a twisted pair UTP version
32. ment If the equipment must be returned for repair follow the Shipping Instructions at the end of this manual 2 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome SurveyorVFT Fixed Dome Components The SurveyorVFT fixed camera dome units consist of an enclosure housing a camera mechanism a shroud and a smoked indoor or clear outdoor lower dome Enclosure The enclosure is a metal shell that houses the camera mechanism for the in ceiling model A safety cord and clip are provided to connect to the camera mechanism during installation In addition a small hole is provided on the side of the enclosure for connection of the lower dome s safety cord A removable top cover a 0 75 inch 19 mm conduit fitting and a pair of rotating flippers that give a convenient and sturdy connection of the enclosure into the ceiling are provided For in ceiling installations that do not use conduit pipe a 0 75 inch 19 mm strain relief fitting provides solid cable anchoring at the enclosure Camera Mechanism The camera mechanism includes an integral camera lens combination with a color camera and a varifocal lens It is designed for easy snap in installation into the enclosure or housing The camera lens position can be manually adjusted The integral PC board provides wiring connections For outdoor units a thermostatically controlled heater is provided for temperature control Shroud The shroud is a 5 4 in 137 mm textured
33. nductor with low DC resistance is required for effective CCTV operation Solid core bare copper conductor is best suited to video applications except where flexing occurs If the coaxial cable will be subjected to flexing during normal use select a cable with a stranded center conductor The preferred dielectric material is cellular foam polyethylene It has better electrical characteristics than solid polyethylene but is more vulnerable to moisture Therefore use only solid polyethylene dielectric cable with a heavy exterior insulation in applications subject to moisture The shield must be copper braid providing 95 or better coverage Cable Types The most commonly used cable types are RG 59 U and RG 11 U Each is actually a family of cables with widely varying electrical characteristics some of which are not suitable for CCTV applications Choose a cable type by referring to the characteristics and maximum distances listed below The maximum distance for best picture refers to the distance between the camera and the unit The characteristics of the cables in this table should be used as a guideline when cables other than Belden are used Materials and construction must follow the guidelines above Note that BC refers to bare copper and TC refers to tinned copper Recommended Coaxial Cable Types Type DC Cable Belden Alpha West Penn Center Type Shield and Resistance Type Type No Type No Type No Conductor Coverage ohms per 10
34. nician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook Bulletin CIB 2 This booklet is available from the U S Government Printing Office Superintendent of Documents Mailstop SSOP Washington D C 20402 9328 ISBN 0 16 045542 1 warning Power must be removed from this unit before removing circuit modules or ribbon cables caution This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge Take all necessary precautions to prevent static discharge Important Safeguards GRAPHIC SYMBOL EXPLANATION The lightening bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point symbol alerts the user to the presence of important operating and maintenance instructions 1 Read Instructions Read all safety and operating instructions before the product is operated 2 Retain Instructions Retain all safety and operating instructions for future reference 3 Heed Warnings Pay attention to all product warnings 4 Follow Instructions Follow all operating instructions 5 Cleaning Do no
35. ning the lock nuts and changing the vertical position of the camera mounting frame within the slots in the mounting bracket Refer to Figure 8 The lens can be manually adjusted On the 5 50 mm lens the telephoto wide adjustment is the front ring iris open and close is the middle ring and focus near to infinity is the end ring On the 2 6 6 mm lens focus near to infinity is the front ring and the telephoto wide adjustment is the end ring iris is fixed Refer to Figure 7 On autoiris lenses a potentiometer is provided for iris adjustment After the camera lens is properly adjusted the lower dome can be installed Lift the lower dome up to the SurveyorVFT and insert the clip of the safety cord from the lower dome into the hole provided on the inside of the housing to anchor the lower dome See label inside housing Holding the lower dome align the two 2 molded tabs on the lower dome with the recesses on the inner enclosure Press the lower dome into the SurveyorVFT and verify that it snaps into place on both sides Tighten the four 4 trim ring screws to hold the lower dome in place Refer to Figure 10 XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation amp 15 Disassembly The SurveyorVFT Fixed Camera Dome can be easily disassembled by removing the camera mechanism from the housing or enclosure A safety cord is always available to safely hang the camera mechanism while assembling or disassembling In Ceiling Installati
36. ns axis roll With the camera powered on and video displayed in a monitor turn the camera to point in the desired direction The tilt position can also be adjusted Loosen the two nuts if necessary on either side of the camera mounting frame use an open end 11 32 wrench Position the camera and retighten nuts The camera mounting bracket position can be adjusted relative to the closeness to the dome by loosening the lock nuts and changing the vertical position of the camera mounting frame within the slots in the mounting bracket Refer to Figure 8 The lens can be manually adjusted On the 5 50 mm lens the telephoto wide adjustment is the front ring iris open and close is the middle ring and focus near to infinity is the end ring On the 2 6 6 mm lens focus near to infinity is the front ring and the telephoto wide adjustment is the end ring iris is fixed Refer to Figure 7 On autoiris lenses a potentiometer is provided for iris adjustment After the camera lens is properly adjusted the lower dome can be installed Lift the lower dome up to the SurveyorVFT and insert the clip of the safety cord from the lower dome into the hole provided on the inside of the housing to anchor the lower dome See label inside housing Holding the lower dome align the two 2 molded tabs on the lower dome with the recesses on the inner enclosure Press the lower dome into the SurveyorVFT and verify that it snaps into place on both sides Refer to Figure 10
37. on 1 Gently pull down on the lower dome s outside edge with two hands until all molded tabs snap out of place Push in the tabs to release the camera mechanism from the enclosure It will hang from the safety cord If it is necessary to completely remove the camera mechanism disconnect the safety cord clip and all cables Pendant Installation On outdoor version only loosen the four 4 trim ring screws from the outdoor lower dome 2 Gently pull down on the lower dome s outside edge with two hands until all molded tabs snap out of place Push in the tabs on the housing until the camera mechanism is released Allow the SurveyorVFT to gently drop down until it is supported by the safety cord If it is necessary to completely remove the SurveyorVFT remove all cable connections and disconnect the clip on the end of the safety cord from the tab on the enclosure 16 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Operation When power is applied to the camera the SurveyorVFT fixed dome views the selected scene Maintenance The SurveyorVFT Fixed Camera Dome requires no scheduled maintenance except for the occasional cleaning of the lower dome Care and Cleaning of Lower Dome Always handle the lower dome by the flange and avoid touching the inside surface 2 If dust or other contaminants accumulate in the dome s interior they should be removed with clean dry air pressure compressed air cans 3 If s
38. op by loosening the 3 screws and lifting it off 4 If cables are used without the use of flexible conduit a Remove the conduit fitting by loosening the nut and sliding it out Install the supplied strain relief fitting in its place and re attach the top cover b Route approximately 12 in 305 mm of cables through the strain relief fitting Tighten the two 2 strain relief fitting screws to compress the cables Do not overtighten the screws and crush the cables 4 If cables are channeled through flexible cable a Route approximately 12 in 305 mm of conduit cables through the conduit fitting b Insert the end of the flexible conduit pipe into the conduit fitting and tighten the clamp screw Continue with the section on Cable Connections Optional Independent Support If it is necessary to provide independent support for the SurveyorVFT fixed dome other than ceiling material order the optional In Ceiling Mount Model Kit model SVFT IC MKT It consists of a pre assembled set of mounting rails and folding ring Refer to Figure 3A 1 With the 7 3 8 inch 187 mm diameter hole cut in the ceiling tile and the tile replaced in the ceiling push the folded assembly up through the hole and unfold 2 Position the assembly squarely over the hole and fasten the caddy rail clips to the existing frame Remove the adjacent tiles to access the clips 3 Adjust the position of the caddy rail clips along the frame to obtain the best X p
39. osition 4 Slide the assembly along the caddy rails to obtain the best concentric Y position Tighten the horizontal adjustment screws to secure the position 5 With the ring concentric with the hole slide the ring vertically along the support slots to obtain the best flush fit in the ceiling The ring should be firmly seated against the tile without warping the tile Refer to Figure 3B 6 Complete the installation as described in the previous procedure When using this kit the flippers squeeze the mounting ring assembly for a snug fit HORIZONTAL ADJUSTMENT SCREWS 2 EACH SIDE NY S MOUNTING RING ae X os CADDY RAILS 2 CADDY RAIL CLIPS 4 ZA y SURVEYORVFT MT di CEILING VERSION A 3 VERTICAL ADJUSTMENT SCREWS 2 EACH SIDE Figure 3A Installation of Optional In Ceiling Mounting Kit 6 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome ADDY RAIL CLIPS C USED FOR X SCREWS USED FOR Y POSITIONING CONCENTRIC FIT RING SHOULD BE FLUSH AND CONCENTRIG SCREWS USED FOR WITH CEILING PLANE Z POSITIONING FLUSH FIT Figure 3B Installation of Optional In Ceiling Mounting Kit Indoor Pendant The indoor pendant model mounts on a Vicon mount or a 1 5 in vertical pipe with an appropriate coupling The pipe is a standard 1 5 in NPT type and must be oriented vertically so the SurveyorVFT fixed camera dome can effectively hang from the pipe Be sure the area around the selecte
40. ounded outdoor cables to protect against voltage surges and static charges Section 810 of the National Electrical Code ANSI NFPA 70 1984 provides information on proper grounding of the lead in wire to an antenna discharge unit size of grounding conductors and the requirements of grounding electrodes 14 Lightning Disconnect the product from its power source and cable system when possible to prevent damage due to lightning and power line surges 15 Power Lines Do not locate outside cables over power or utility lines where they can fall and make direct contact Contact with power lines can be fatal 16 Overloading Do not overload wall outlets and extension cords to prevent risk of fire and electric shock 17 Object and Liquid Entry Never probe through or spill liquid into enclosure openings to prevent risk of fire or electric shock 18 Servicing Refer all servicing to qualified service personnel 19 Damage Requiring Service Obtain service when a The power supply cord or plug is damaged b Objects have fallen or liquid has been spilled into the product c The product is not designed for outdoor use and has been exposed to water or moisture d The product does not operate per the operating instructions Perform Vicon recommended adjustments modifications and troubleshooting only to avoid unit damage and personal injury e The product has been dropped f The product shows a significant change in performan
41. pots streaks or stains appear on the interior or exterior they can be removed with a solution isopropyl alcohol and water using a microwave safe aluminum free paper towel Dry with clean dry pressurized air 4 Scratches or surface blemishes on the exterior or interior may be removed with a nonabrasive wax using a soft nonabrasive cleaning cloth Either liquid or spray cleaner wax suitable for fine furniture is acceptable caution Excessive rubbing of the dome s surface can cause permanent scratches that may render the dome unusable 5 Clean all surfaces with any soft nonabrasive cleaning cloth and cleaning agent suitable for acrylic plastic caution For warranty protection implement this instruction exactly as stated Fuse Replacement There is a fuse located in the SurveyorVFT When necessary replace it with a fuse of the same value 0 5 A 250 V 5x20 mm slo blo for indoor version the outdoor version has an additional 1 0 A 250 V 5x20 mm slo blo fuse XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Operation e 17 Shipping Instructions Use the following procedure when returning a unit to the factory 1 Call or write Vicon for a Return Authorization R A at one of the locations listed below Record the name of the Vicon employee who issued the R A Vicon Industries Inc 89 Arkay Drive Hauppauge NY 11788 Phone 631 952 CCTV 2288 Toll Free 1 800 645 9116 Fax 631 951 CCTV 2288 For service or retu
42. rifocal SVFT P550M C with manual iris 51 8 5 6 39 2 4 3 SVFT W266DNA 2 6 6 varifocal SVFT W266DNA C with autoiris 82 05 38 26 60 32 28 66 SVFT W266A 2 6 6 varifocal SVFT W266A C with autoiris 106 47 6 78 2 35 8 SVFT W550A 5 50 varifocal SVFT W550A C with autoiris 51 8 5 6 39 2 4 3 XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Vicon Standard Equipment Warranty Vicon Industries Inc the Company warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period of three years with the following exceptions 1 VCRs all models Labor and video heads warranted for 120 days from date of original retail purchase All other parts warranted for one year from date of original retail purchase 2 Kollector Elite Kollector Pro and ViconNet Systems hardware only all models Hard Drives warranted for three years All other parts warranted for 18 months AurorAcorD Hard drives floppy drives CD R W DVD drives and any and all archive media warranted for 18 months All other parts warranted for three years from date of original retail purchase eo RAID Storage Devices and Hard Drives all models Warranted for one year from date of original retail purchase Video monitor CRT cathode ray tube and LCD monitors all models One year from date of original retail purchase NOVA 1500 CPU Hard drives
43. rns from countries in Europe contact Vicon Industries Ltd Brunel Way Fareham PO15 5TX United Kingdom Phone 44 0 1489 566300 Fax 44 0 1489 566322 2 Attach a sheet of paper to the unit with the following information Name and address of the company returning the unit a b Name of the Vicon employee who issued the R A c R A number d Brief description of the installation e Complete description of the problem and circumstances under which it occurs f Unit s original date of purchase if still under warranty Pack the unit carefully Use the original shipping carton or its equivalent for maximum protection Mark the R A number on the outside of the carton on the shipping label 18 e Shipping Instructions XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Reference Coaxial cables used to route video signals to and from the unit must meet the video recommendations in this section caution Careful selection of the proper cable is essential to obtain the best performance from this equipment Vicon assumes no responsibility for poor performance when cables other than those recommended are installed In all cases coaxial cable impedance should be 75 ohms Materials Use only cable with a pure copper center conductor Do not use cable with either a copper plated steel or an aluminum center conductor because these do not transfer signals effectively in the frequency range used in CCTV networks A center co
44. sted in three axes horizontally pan vertically tilt and rotation about the lens axis roll With the camera powered on and video displayed in a monitor turn the camera to point in the desired direction The tilt position can also be adjusted Loosen the two nuts if necessary on either side of the camera mounting frame use an open end 11 32 wrench Position the camera and retighten nuts The camera mounting bracket position can be adjusted relative to the closeness to the dome by loosening the lock nuts and changing the vertical position of the camera mounting frame within the slots in the mounting bracket Refer to Figure 8 The lens can be manually adjusted On the 5 50 mm lens the telephoto wide adjustment is the front ring iris open and close is the middle ring and focus near to infinity is the end ring On the 2 6 6 mm lens focus near to infinity is the front ring and the telephoto wide adjustment is the end ring iris is fixed Refer to Figure 7 On autoiris lenses a potentiometer is provided for iris adjustment In some installations the picture may be squared up by rotating the lens about its own axis up to 360 roll adjustment Aux Video Output Nut for tilt adjustment Telephoto Adjustment for 5 50 mm Focus Adjustment for 2 6 6 mm Telephoto Adjustment for 2 6 6 mm Focus Adjustment for 5 50 mm Figure 7 Camera Lens Adjustments 5 50 mm Version Shown 12 e Installation XX152 02 00 Rev
45. such as steel beams headers pipes electrical wiring etc that would interfere with mounting Video sync and power cables must be routed to the location 1 Mark with the scribe and cut a 7 3 8 in 187 mm hole in the ceiling at the desired location Remove the tile from a dropped ceiling if necessary Feed all necessary flexible conduit pipe or cables down through the hole 4 e Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome 2 2 If cables are used without the use of flexible conduit a Remove the enclosure top by loosening the 3 screws Remove the conduit fitting by loosening the nut and sliding it out Install the supplied strain relief fitting in its place and re attach the top b FOI the enclosure near the hole in the ceiling and route cables through the strain relief fitting If cables are channeled through flexible cable a Hold the enclosure near the hole in the ceiling and route conduit cables through the conduit b fina the end of the flexible conduit pipe into the conduit fitting Cable length should be flush with the bottom of the enclosure approximately 12 in 305 mm Tighten the clamp screw Lift the enclosure up through the ceiling hole Turn and tighten the flipper screws to obtain a flush fit with the ceiling plane Connect the enclosure s safety cord clip to the tab in the camera mechanism to allow the drive to hang from the enclosure Refer to Figure 2 for location of tab Continue wi
46. t use caustic abrasive or aerosol cleaners a For units that CAN BE DISCONNECTED from the power source use a damp cloth for cleaning b For units that CANNOT BE DISCONNECTED from the power source use a damp cloth for cleaning and do not allow moisture or liquids to enter vents 6 Attachments Use only Vicon recommended attachments to prevent unit damage and personal injury 7 Water and Moisture Use only products designed for outdoor environments where they will be exposed to water or moisture 8 Accessories Do not place the unit on an unstable surface to avoid falling Use only Vicon recommended mounting accessories 9 Ventilation Do not block ventilating slots and openings as they ensure reliable operation Do not place the unit near a heat source or into an enclosure unless recommended by Vicon 10 Power Sources The product should only be operated from the recommended power source If not specified consult your Vicon dealer or local power company 11 Grounding Only products equipped with a 3 prong grounded plug should be inserted into a grounded power outlet Contact an electrician to replace an obsolete outlet Do not force a plug into a non grounded outlet 12 Power Cord Protection Power supply cords should not be routed in trafficked areas or in tight spaces where they will be pinched or used to bear weight Allow some slack in the cord where it enters the unit 13 Outdoor Cable Grounding Use only gr
47. th section on Cable Connections Figure 2 Safety Cord Installation Mounting from Above the Ceiling Use this method of installation if there is access to the space above The ceiling material must provide suitable strength to support the weight of the SurveyorVFT fixed dome with the two flippers on the enclosure Refer to the section on Optional Independent Support for installations requiring additional support Be sure the area around the selected location is clear of obstacles such as steel beams headers pipes electrical wiring etc that would interfere with mounting Video sync and power cables must be routed to the location 1 Mark with the scribe and cut a 7 3 8 in 187 mm hole in the ceiling at the desired location Remove tile from dropped ceiling if necessary Feed all necessary flexible conduit pipe or cables down through the hole Lift the SurveyorVFT enclosure up to the ceiling and snap it into the hole Turn and tighten the flipper screws for a flush fit Connect the enclosure s safety cord clip to the tab in the camera mechanism to allow the mechanism to hang from the enclosure Align the 2 slots on the camera mechanism with the tabs in the enclosure being sure to match up the arrows on both the drive and in the enclosure Insert the camera mechanism into the enclosure until it snaps into place XX152 02 00 Rev 1004 SurveyorVFT Fixed Camera Dome Installation e 5 3 Working above the ceiling remove the enclosure t
48. ts E Attach the male BNC connector on the video cable to the mating connector on the PC board PRINTED CIRCUIT BOARD coax version or connect twisted pair wire to screw terminal Insert the clip of the safety cord on the lower dome into the hole on the enclosure Lift lower dome up to unit and align the molded tabs with the recesses on the inner enclosure Lower dome snaps into place Refer to the Maintenance Section for lower dome handling o S BNC VIDEO CONNECTOR N n POWER SCREW TERMINAL BLOCK Y Y E EI DNG TWISTED PAIR SCREW TERMINAL D VIDEO CONNECTOR UTP version Press power cable connector onto board connector Push any excess cable up into the ceiling to ensure that it does not get wedged between the enclosure and the mechanism In Ceiling No Access to Ceiling ii e Quick Installation XX152 02 00 Rev 1204 SurveyorVFT Fixed Camera Dome Replace enclosure top cover Do not apply power yet f Make any necessary camera lens adjustments Working above ceiling remove enclosure top cover B Lift enclosure up through ceiling hole turn and tighten flipper screws Align the two slots on the enclosure with the two tabs on the camera COVER pen mechanism Matching up the arrows slide the mechanism into the enclosure until it snaps securley into place ENCLOSURE FLIPPER EN ent ntn nentes eee ener nnn ng i FOR CABLE USE WITH p sl
49. uiring external video synchronization As an example equipment like a video switcher unit uses the camera s line lock to reduce video jump on its monitor during camera switching The V phase pot allows video to power line phase adjustment up to 180 If more than 180 of adjustment is required swap the lines attached to the 24 VAC terminal block connector Be sure that the selector DIP switch is set to position LL Note that the performance of the camera s line lock depends on the quality of the power source If the camera experiences roll or jitter due to the quality of the power source then it is best to set the camera to internal crystal mode This is done by setting the selector switch to INT The adjustment for the line lock V phase VR1 is on the bottom board of the camera Autoiris Adjustments On autoiris lenses iris adjustment may be required if the picture appears dark or grainy or has poor color To obtain the sharpest picture possible the iris adjustment should be made from a full bright setting down to an acceptable video level This assures that the internal AGC of the camera is not operational There is a potentiometer to adjust the DC level for autoiris potentiometer VR1 is on the camera front board Refer to Figure 5 Use a small jeweler s screwdriver to make adjustments Turning the potentiometer opens and closes the iris to regulate light extremes Turning the potentiometer clockwise opens the iris

Nikon XX152-02-00 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents