Nikon Coolpix S500 User's Manual
Contents
1. lens slightly or a shadow may appear in the lower left picture Hold the camera steady a second or two after pressing corner of close up photographs The lens port may block some the shutter release button F of the light Installing the flash diffuser will help to eliminate A Do not shoot down on subjects a gt they will quite often blend the shadow You can test this above water into the background and be difficult to see in the photograph Shoot subjects straight on or shoot up at a slight angle using To shoot photographs closer than 2 feet 0 6m you need to the blue Walter as a contrasting background 5 Underwater flash is used to restore the warmer colors filtered use an external strobe such as the DS51 or DS125 With an external strobe you can position it so nothing blocks the light path between the strobe and the subject 17 Photo Tips Cont 6 When using daylight or flash if your camera consistently over out by the water as well as to illuminate the subject When photographing underwater set the camera to use flash on every shot If the camera s flash is set to AUTO and the sun is behind your subject the camera may see enough light that it does not fire the flash With the sun behind the subject the subject is shaded dark and needs flash for a good exposure 18 Ikelite Limited Warranty All Ikelite products are warranted against any manufacturing defects or underexposes the image you may want to adjust your cam2. the housing and the housing back Lift the lid snaps so they are extended and place the lid housing back snap into the hook on the housing back To close the housing push even gap down on the lid snaps until all 4 sides 3 they snap into place Lid f iit snaps on opposite sides of the housing should be closed at the same time Be sure they are down far enough to engage the lock o ring housing o ring housing Double check Once the housing is closed check the o ring seal Check the gap between the housing back and the housing it should be even all the way around Look through the clear plastic back at the o ring You should see a darkened area where the o ring is compressed against the housing back If you do not see an even black compression seal all the way around the back open the lid snaps reseat the housing back and close the lid snaps Visually check the seal again 5 Lubricants 1 Ikelite provides silicone lubricant with the housing We recommend you use only Ikelite lubricant on Ikelite products as some other brands may cause the o ring to swell and not seal properly Use only enough lubricant to lightly cover control shafts and o rings Wipe off any excess lubricant with a clean cloth Lubricant is not a sealant it is used to reduce friction Excessive lubricant can collect sand and dirt which may interfere with proper sealing CAUTION Never use spray lubric
3. Ikelite Digital Housing Please Read We suggest that you read this instruction booklet thoroughly instruction manual before use If you are new to underwater photography be sure 6184 50 for Nikon CoolPix 500 to read the General and Photo Tips We also suggest that you read the camera manual thoroughly to have a full understanding of where each camera control is located and what function each control provides Please Read If Using an EV Controller The EV Controller used with Ikelite DS Substrobes have two user settings One setting is for strobe selection the other is for pre flash or non pre flash This camera uses pre flash thus the EV Controller should be set to the pre flash position when used with this camera Congratulations on your purchase of an Ikelite Digital Camera Housing Ikelite has over 40 years of experience in the underwater photographic and lighting market Our products are designed and built in the USA by Ikelite for both the professional and amateur photographer The clear housing permits instant visual inspection of the camera and all sealing surfaces as well as complete monitoring of controls and camera LCD screens Ikelite Digital Housings are slightly negative in salt water for stability This housing has been water pressure tested at the factory Housing is pressure tested to 200 60m Opening the Housing 1 Lid Snaps have a Lock To open push Lid Snap Lock forward and lift as shown Keep pressure on t
4. ants as the propellant ingredient can cause the plastic housing to crack Checking Controls Once the housing has been closed make sure the housing controls line up with the camera s controls If the housing controls are misaligned slightly make sure the camera hold down bolt has been tightened down firmly so the camera is flat against the tray Rotary Multi Selector Control The camera s rotary multi selector is made up of the rotating ring and the OK button When selecting menus or pictures you can either press the rotating ring up down left or right or rotate it When choosing from numerous menu items or pictures rotating the ring is recommended for easy scrolling and faster operation The housing s rotary multi selector control uses a paw to turn the rotating ring Note that the white dot on the face of the housing s control knob indicates the paw location When underwater the water pressure will push the housing s rotary multi selector in and make contact with the camera s rotating ring if the paw is over the ring It is recommended that the paw be turned to the 3 o clock position when not being used so the paw is Not in contact with the rotating ring To use the housings rotary multi selector control underwater you will need to pull out on the control locate the paw over the camera s rotating ring push in and rotate the ring You may have to do this several times depending on the length of the camera menu It is recom
5. ens After use rinse and gently dry the lens port to avoid water spotting To clean use a mild soap solution or lens cleaner Do not use alcohol or window cleaner on the Lens Port The Lens Port will accept 2 Wide Angle Adapters The Wide Angle Adapter 9306 80 which is required to mount the Inon UWL 150AD Bayonet style wide angle lens The Wide Angle Adapter 9306 81is required to mount the 6420 Ikelite W 20 Wide Angle Lens and other manufacturers 67mm screw thread style wide angle lenses These lenses can be secured onto the Wide Angle Adapter above or below water as they are designed to have water between the front of the port and the accessory lens Make sure no air bubbles are trapped between the port and the accessory lens Any vignetting that occurs can be eliminated by zooming the camera lens slightly The camera s built in flash cannot be used with wide angle lenses The front of the lenses are so large they block the camera s flash To properly light subjects sm when using a wide angle lens an external strobe should be used Due to the wide angle of coverage of these lenses the DS125 Substrobe is recommended or two DS51 Substrobes Wide Angle Adapter Wide Angle Lens 10 Optional Accessories Substrobe DS51 Package 3944 54 ra A The Substrobe DS51 package includes the Substrobe DS51 the EV Controller and ball socket arms The EV Controller provides 10 manual power settings in 1 2 stop increm
6. ents An external strobe offers several advantages over using the camera s built in flash External strobes move the flash away from the camera lens which helps reduce backscatter They also expand lighting options to achieve the best Ball Socket lighting for different subjects A second external digital strobe package can be added to fill the shadows and produce more realistic photographs The Substrobe DS51 covers the equivalent of a 28mm lens It is the ideal choice when using only the camera lens or the camera lens with a macro accessory lens EV Controller If an accessory wide angle lens wider NOTE than 28mm is used the ideal Optional Tray and lighting choice is the Substrobe Release Handle DS125 which covers 100 degrees or required to mount two Substrobe DS51 s can be used Substrobes 12 Optional Accessories Substrobe DS125 Package 3944 77 Substrobe a The Substrobe DS125 package includes the Substrobe DS125 the EV Controller ball socket arm and charger The EV Controller provides 10 manual power settings in 1 2 stop increments An external strobe offers several advantages over using the camera s built in flash External strobes move the flash away from the camera lens which helps reduce backscatter They also expand lighting options to achieve the best lighting for different subjects A second external digital strobe package can be added to fill the shadows and produce more realistic photogra
7. era s exposure compensation settings Many cameras allow you to adjust both available light and flash exposure with an EV control in the camera s menu for a period of one year from the date of purchase Defective products should be returned prepaid to Ikelite Ikelite will at its discretion repair or replace such products and will return to customer prepaid All other claims of any nature including but not limited to bulb failure are not covered Except as mentioned above no other 7 Many photographers transfer their images to the computer warranty expressed or implied applies to this Ikelite product where they can fine tune the appearance of the image Many of the image manipulation programs make you think you can magically correct any image taken and make a good picture One thing to remember when using image manipulation programs if the image is overexposed much of the color is missing If the color is missing you cannot adjust it If images are slightly underexposed the color is there it is just dark and you can adjust it to some degree So if you error in exposure it is better to have the image slightly underexposed than over exposed Returning Products for Service Ikelite is most interested in preforming any service to assure that all products perform as intended For repair or service return the product to the address below with your name address phone number and a brief description of the problem Evidence of purchase da
8. g for safe keeping CAUTION Never use spray lubricants as the propellant ingredient can cause the plastic housing to crack 14 Control Maintenance Cont 3 Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it or return the housing to Ikelite for maintenance To remove the control loosen the set screw in the knob allen wrench required remove the knob If there is salt or dirt build up on the exposed control shaft clean the shaft Open the housing and gently slide the control shaft out of the control gland Clean and lightly lubricate the shaft including the end of the shaft Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland Replace the knob NOTE the flat area on the shaft the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft control shaft Flat Tighten set screw down against this area when replacing the knob peas diana Loosen set screw allen wrench required Lubricate end of shaft before reingerting into gland 16 General Tips 1 Due to the power required to operate the camera flash and LCD screen it is a good idea to start each dive with a fres
9. h set of batteries Photo Tips 1 The number one rule in underwater photography is eliminate as much water between camera and subject as possible Get as close as you can to the subject then use the zoom If you 2 Some cameras reset their flash to AUTO when the camera is are using flash subjects beyond 6 feet 1 8m will not have turned on If you prefer another setting be sure to select it much color 3 As soon as you enter the water take a moment and check the 2 The camera s built in flash is very close to the camera lens The housing to see that it is properly sealed flash can light up any suspended particles in the water and they 4 Next check to see if there are any bubbles on the face of the can be recorded in your picture This effect is called backscatter lens port If there are take your finger and remove them If To eliminate as much backscatter as possible photograph close there are bubbles on the lens port they can produce soft focus Photograph in clear water do not stir up the sand or silty spots in your photographs bottom If backscatter becomes a problem in the environment you are photographing an external flash will help eliminate NOTE much of the backscatter 5 If you are shooting with the camera s built in flash and the 3 Digital cameras have a slight lag time between when you press cameras lens is set to the widest angle you may need to zoom the shutter release button and the camera actually takes the the
10. he Lid Snap so it does not fly open quickly Lift Some lid snaps have a lot of spring tension once they go over center have a firm grip on the aoe lid snap Lid Snaps may be opened one at a time Push Forward One Touch Fortrait Anti Shake Lid Snap Lock Shutter Release Lid Bap Installing the Camera Remove the back from the housing The mounting tray for the camera is secured to the housing back Position the camera on the tray and secure it with the mounting bolt Th mb which threads into the camera s tripod socket Use a coin or flat bladed screwdriver to tighten the mounting bolt so the camera is flat against the tray Mounting Tray ounting Bolt Selector OK 0O CAMERA MOUNT Menu O CAUTION i Delete Rotary Some camera tripod socket threads are plastic The mounting Multi tray bolt is metal Do not cross thread or over tighten as you eelniar may damage the camera tripod socket threads Back View 3 4 Closing the Housing 1 2 Place housing face down in your housing back lap or on flat surface lt s Check to see that there is an o ring on the housing back and o that it is clean and in its proper location Guide the back onto the housing The o ring should touch the housing all the way around There should be an even gap all the way around between
11. mended you practice using this control above water Turn Camera On Turn the camera on and operate each of the housing controls to get a feel for using the camera in the housing Take a few pictures above water with the camera in the housing Using Flash Using the Camera s Built in Flash If you do not have an external flash the camera s built in flash can be used See Diffuser instructions Diffuser amp Deflector Installation Diffuser Housing shown with Diffuser installed Diffuser and Deflector cont Diffuser Deflector material A diffuser and deflector are included with the housing The diffuser is white transparent plastic The deflector is also white but is not transparent To install the diffuser or deflector spread the port clamp at the spring end and slide over the lens port The white plastic should be placed in front of the camera flash The port clamp should be pushed back against the front of the housing Diffuser The diffuser should be installed when using the camera s built in flash When shooting with the camera s built in flash at approximately 2 feet 0 6 m or less the lens port on the housing may block a portion of the light from the camera s built in flash creating a shadow in the lower left of the photo If this occurs zoom the lens slightly to eliminate the shadow You can test this above water Deflector The deflector should be installed when using an external strobe s
12. mmend that the housing be returned to Ikelite periodically to be checked and pressure tested 1 2 3 Do Not leave the camera and housing in direct sunlight for prolonged periods Heat may damage the camera Do Not ship the camera in the housing Before using the housing always check the tightness of the set screw in each control knob Check each control gland penetrating the housing to make sure they are tight There is a slight chance that either could vibrate loose during travel Keep the back o ring clean and lightly lubricated To lubricate remove the o ring from the back Put a small amount of Ikelite lubricant on your fingers Draw the o ring through your fingers to apply a light coating of lubricant Only apply enough lubricant to make the o ring feel slick Do Not stretch the o ring This light coating of lubricant will help to keep the o ring from drying out and will help to show a dark sealing line when the housing back is properly sealed Keep the area where the o ring fits and the sealing surface of the housing clean Rinse the housing exterior thoroughly in fresh water after each salt water use Dry with a soft cloth Dry lens port to eliminate water spotting After several uses in salt water soak the housing exterior in a mild soap solution rinse and dry before storage When storing the housing remove the back o ring lightly lubricate and place in a plastic bag Place the plastic bag with o ring inside the housin
13. phs Ball Socket The Substrobe DS125 covers the equivalent of a 18mm lens 100 degrees It is the ideal choice when using accessory wide angle lenses greater than 28mm EV Controller NOTE Optional Tray and Release Handle required to mount Substrobes 13 Control Maintenance Ikelite controls are designed to provide years of reliable service with minimal maintenance 1 Push button controls require no maintenance other than rinsing in fresh water after saltwater use If a push button control becomes difficult to push or if it sticks when depressed soak the housing in luke warm fresh water After a few minutes operate the push button If this does not correct the problem return the housing to Ikelite for maintenance lubricate shaft housing _ cael gt pull out to expose shaft Some of the controls have long shafts These controls can be pulled out exposing the shaft see drawing To lubricate the control gently pull on the knob until the stainless steel shaft is exposed Lightly lubricate the shaft then move the shaft in and out several times This will lubricate the x ring in the Ikelite control gland This should be done before using the housing after a prolonged storage period or once a week when the housing is in use 15 Maintenance The Ikelite Digital Housing should be given the same care and attention as your other photographic equipment In addition to normal maintenance we reco
14. te must be provided to obtain warranty service Ikelite Underwater Systems 50 W 33rd Street Indianapolis IN 46208 USA 317 923 4523 email ikelite ikelite com www ikelite com D Digital 6184 50 0 0607
15. uch as the DS51 or DS125 Substrobe and EV Controller The deflector will redirect the camera s flash to the EV Controller which controls the external strobes output Spread to Install Optional Accessories Back o ring 0109 O rings last for several years if properly maintained See maintenance Always carry a spare in case o ring becomes damaged or lost Wide Angle Adapter 9306 80 Required to mount Inon UWL 150AD Bayonet style wide angle lens Wide Angle Adapter 9306 81 Required to mount Ikelite W 20 and other Screw Thread 67mm style wide angle lenses UR Pro Filter Blue Water 644132 The UR Pro underwater color correcting filter is designed to restore some of the warm colors filtered out by the water For available light use only not recommended for use with flash Green Water Filter 644172 Enhances contrast and alters the color of green water to give our subject a rich natural tone For available light only not recommended for use with flash Tray with Release Handle 952331 Tray and Release Handle is required to mount external Substrobes Ikelite W 20 Wide Angle Lens 6420 Wide Angle lenses allow you to capture more of the scene and get closer to your subject which results in clearer images and more vivid color Can be installed or removed underwater for maximum versatility Note some housings may require an adapter see instructions 11 Lens Port Treat the glass in the lens port as a camera l
Download Pdf Manuals
Related Search