Newcon Optik NVS 4 User's Manual
Contents
1. 16 1 OVERVIEW The night vision NVS 4 is aiming optical electronic weapon scope intended for shooting gun with the side mount at night time or dark conditions The unit utilizes a generation 2 or better image intensifier tube which amplifies available moonlight starlight or man made light The device was designed to be easy to use and provide many years of operation Some of the typical activities where NVS 4 will be useful e Military e Law enforcement e Security Features e Suitable for a variety of infantry AK 47 variants and machine guns Supplied with East Block side mount or a custom mount Precise internal Windage Elevation adjustments Lit ballistic reticle with adjustable brightness intensity Automatic brightness protection Precautions NVS 4 is a sophisticated precise optical instrument equipped with electronics Therefore it should be handled with due care e Keep your device away from direct sunlight impacts dust moisture and sudden changes of temperatures e Do not touch the optical surfaces with fingers Doing so may damage the anti reflection coating e Cleaning of optical surfaces is allowed only with professional camera lens cleaning supplies e Use only a soft clean cloth to clean the exterior of the device e Do not take the cover off the lens if not necessary e Keep away from heating appliances and central heating e Make sure to switch off the unit and remove the batteries2. 10 7 STORAGE The scope must be prevented against mechanical damages The scope is to be stored in a heated room Ambient temperature must be within the limits from 5 to 35 C Relative humidity must not exceed 85 It is recommended to keep the scope in its caring case without a battery inserted 11 8 TROUBLESHOOTING The device does not work Check that the battery is installed properly Check the charge of the batteries Replace if it is weak The image is degraded and blurred Clean the lens with napkin If the inner optics suffers from extended humidity send the scope to the manufacturer for drying and sealing Unit flashes It is normal for the unit to flash within the first 2 minutes of activation If the flashing continues afterwards the following is a possible cause bright environment even with the caps closed 12 Condensation accumulates on the parts It is O K to use the unit in cold However when the unit is brought from the cold into a warm environment it has to warm up for up to 2 hours not minutes Only then it is allowed to turn it ON again Visibility decreases and or disappears Bright light sources moon projectors or headlights may cause visibility to degrade or even completely disappear Move the device away from the light source immediately The image should be restored in within 2 minutes Poor atmospheric conditions such as fog haze or extremely dark environments will dec
3. during periods of non operation and when storing the device for long period of time e Do not apply superfluous efforts at work with lens assembly agile elements and thread connections Due to considerable optical magnification of the eye piece some small structures inside the tube coating in the form of dark and or white points may be seen in the field of view which does not affect the serviceability of the device 2 2 DELIVERY SET NVS 4 is supplied with the following components Quantity NVS 4 unit 1 Wrench 1 Soft case 1 Napkin 1 Manual 1 Warranty registration card 1 Exact delivery set and accessories included are subject to the terms of specific contract 3 SPECIFICATIONS NVS4 NVS4 Sx Typical range at 350 500 starlight m Image Intensifier tube 2 2 Magnification x 4 5 Field of view under 63 6 eye relief 40 mm deg Exit pupil diameter 6 6 mm Mount East European East European Battery AA 1pc AA 1pc Supply voltage V 1 5 1 5 Continuous operation depends on 10 30 depends on time under standard batte n batie conditions h Ty typ ty typ Overall dimensions 207x176x79 220x198x100 Weight kg 0 9 1 25 AK47 AK74 DR List of recommended weapons AK74M AK101 AK102 AK105 AK107 AK108 AN94 AS BSS AK74M AK101 AK102 AK105 AK107 AK108 AN94 AS BSS PKM SVD 4 4 DESIGN 15 714 1312 10 Figure
4. 1 Sight left 51016 view without cap and light filter Figure 1 2 Lens 3 Fitting part 4 Scope housing 5 Clip 6 Eye shield 8 Battery compartment cover 9 Lead 10 Scope housing cover 11 Washer 12 Stop screw 13 Latch 14 Lock lever 15 Handle 16 Bracket 17 Reticle brightness adjustment hand wheel 18 19 20 21 Figure Z Sight right side view Figure 2 1 Lens cup with 7 Switch brightness filter 18 Vertical adjustment 19 Cover of blow out fitting screw 20 Rubber gasket 21 Horizontal adjustment screw 6 5 OPERATION INSTRUCTIONS The scope is mounted on a weapon by means of clamp which consists of bracket 16 Fig 1 2 lock screw 2 latch 13 lock lever 14 handle 15 and washer 11 Mount the scope on a weapon in the following order pull the handle 15 direct the scope from the rear side into aligning bar of a weapon and push the scope forward to stop push the handle 15 up to its catching check up the reliability of scope fastening A swinging of the scope on a weapon is not affordable For reliable fastening of the scope it is necessary to adjust the clamp in the following order detach the scope from the weapon unlock the latch 13 shift the handle 15 providing the reliable fastening lock the latch 13 check the reliability of scope fastening again For mounting and checking the serviceability
5. No NEWCON OPTIK Operation Manual NIGHT VISION WEAPON SCOPE NVS 4 105 Sparks Ave Toronto ON M2H 255 Canada IMPORTANT INFORMATION Read prior to activation You have just purchased a complicated electronic device To operate it properly please read this manual carefully Here are some common precautions that must be noted e NEVER disassemble the unit This device contains high voltage which may be hazardous to your health e NEVER expose the opened objective lens of an active unit in daylight At daytime objective lens must be covered by caps There is a tiny hole in the cap to provide enough light for daytime operation It is allowed to turn on the unit at daytime but caps must cover the lenses e NEVER aim active unit at intense light sources i e lights headlamp campfires the moon etc e NEVER reverse the polarity of a battery NEVER connect the unit to external power sources ALWAYS remove batteries when not in use for a long period e ALWAYS keep the objective lenses covered when not in use e ALWAYS store in a warm dry place when not in use S9 er En opes ua B rs Table of contents OVERYVIEW heben ee sts 1 DELIVERY SE 3 SPECIFICATIONS ee 4 DESIGN detiene eet deis 5 OPERATION INSTRUCTIONS 7 MAINTENANCE 10 SEO 11 TROUBLESHOOTING ee 12 WARRANTY EE 14 CUSTOMER SUPPORT eee 15 ACCEPTANCE CERTIFICATE
6. RT Should you experience any difficulties with your NEWCON OPTIK product consult the enclosed manual If the problem remains unresolved contact our customer support department at 416 663 6963 or toll free at 1 877 368 6666 Our operating hours are 9am 5pm Monday Friday Eastern Standard Time At no time should equipment be sent back to Newcon without following the instructions of our technical support department NEWCON OPTIK accepts no responsibility for unauthorized returns To locate NEWCON Authorized Dealer call Tel 416 663 6963 Fax 416 663 9065 Email newconsales newcon optik com Web www newcon optik com The defective products should be shipped to From the USA only 2331 Superior Ave Cleveland OH 44114 From all other countries 105 Sparks Ave Toronto ON M2H 285 CANADA 15 11 ACCEPTANCE CERTIFICATE NIGHT VISION DEVICE NVS 4 Serial number Complies with all technical specifications and has passed the inspection Date of production Quality Inspector Quality Assurance Se 16 NEWCON OPTIK 2010 Printed in Canada
7. of the scope under daylight conditions do as follows put the cup with light filter on the lens 7 remove the cover 8 and insert the battery as shown on the cover of scope Screw up the cover 8 tum on the switch 7 In 3 4 seconds the eyepiece field of view should begin to gleam with yellow green light and red aiming reticle adjust the optimal contrast of aiming reticule by means of hand wheel 17 ifreticle is switched on but is extinct with the lit screen the battery should be replaced with operable one Warning the reticle extinction indicates the discharge of battery The central peak of reticle is assigned for sighting The vertical markers on each side of central peak can be used for lateral deflection at moving target or strong wind The scope should be aligned to the weapon by means of zeroing Zeroing Is carried out in the daytime and with the light filter cap put on only in the following order setthe target of approximately 1x1 m at the range 100 m make the 3 4 shoots from rest at regular aiming of the peak to centre of target determine the mean point of impact by holes placement If mean point of impact disagrees to aiming point more than by 3 cm the scope alignment is needed Align the scope by mean of screws for vertical and horizontal adjustments The turn by one click corresponds to shift of mean point of impact by 3 cm at the range of 100 m 8 Note If zeroing range is different the
8. rease the visibility distance of the unit Reticle is absent or weak Check the batteries 13 9 WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date of the original purchase but no more than 18 months from the date of manufacturing Longer warranty is available subject to the terms of the specific sales contract Should your Newcon product prove to be defective during this period please deliver the product securely packaged in its original container or an equivalent along with the proof of the original purchase date to your Newcon Dealer Newcon will repair or at its option replace with the same or comparable model the product or part thereof which on inspection by Newcon is found to be defective in materials or workmanship What This Warranty Does Not Cover NEWCON is not responsible for warranty service should the product fail as a result of improper maintenance misuse abuse improper installation neglect damage caused by disasters such as fire flooding lightning improper power supply or service other than by a NEWCON Authorized Service Postage insurance and shipping costs incurred while presenting your NEWCON product for warranty service are your responsibility If shipping from North America please include a cheque or money order payable to NEWCON OPTIK for the amount of 15 00 to cover handling and return shipping 14 10 CUSTOMER SUPPO
9. value of click changes proportionally for example atrange 50 m 1 5 cm at range 200 m 6 0 cm Example On the Fig 3 the mean point of impact is located above the aiming point by 15 cm and at the left by 20 cm To shift the mean point of impact to target centre one should turn the vertical adjustment screw by 15 3 5 clicks down and the horizontal adjustment screw by 20 3 7 clicks to the right Make the batch of check shooting Grouping of scope aimed shooting should not be worse than without the scope No adjustment should be made after zeroing When shooting a range exceeding 100 m you should keep zeroing but choose another aiming point corresponding to the distance to the target i g d o Hopi 1 1 CN p 4 3 IL Figure 3 6 MAINTENANCE The device should be kept clean avoiding dust and dirt The outer surfaces of the optical parts should be clean always WARNING It is prohibited to disassemble the scope to switch on the scope without protective cap and light filter to apply exceeding force to clamp to use a battery of improper type to keep a battery into an unused scope for a long time The device is the subject of following periodic maintenance procedure clean the scope against dust dirt and moisture check out the contacts of power supply wipe grease spots on optical surfaces by clean napkin in case of significant pollution the alcohol can be used
Download Pdf Manuals
Related Search