New Media Technology IP Power 9212 User's Manual
Contents
1. will even connect contrary port 10 Digital inputs provide de bouncing function 11 Update firmware by the TCP IP network 12 SDK Software Development Kits provided 13 Embedded WATCH DOG 14 Compatible with OUR IP Kamera 9000 IP Video 9100 and IP Power 9201E IP Sensor for monitoring control and detection via any online PC 15 Support GPRS setting by for online Cell phone item limit 16 Support SMTP Send IP address by E mail as log in and send e mail as detecting sensor trigger Specification 1 DC 5V AC90 240 input 2 D SUB In amp Out port 3 RJ45 Application field can be associated with any kind of electrical equipments no matter household appliances or security equipment It can manage the power supply through the web page make it be safer for the security equipment and more convenience for digital control at the far end Industrial application field bank financial security system jewels casino cash register in supermarket park traffic control military equipment and airport IP POWER 9212 USER MANUAL 2 Before you start 9212 package contents E One set of IP POWER 9212 Main Board 9200 Sensor board 9201 Pro Control Board 9202 Pro One network wire with RJ45 port One 1A 110 220V adaptor One D Sub 15 Pin cable One install disc One rapid install manual Minimum System Requirements Minimum Intel Pentium II 300MHz compatible AMD processor WINDOWS ope2. superuser and press ok then press the reset button in 9200 it will back to the default settings Now you can enter the administration page Q2 I cannot open the IE web page why A2 Please update your IE or use the up to date version of Netscape browser Q3 Why the on off operation can work immediately A3 if you operate the IP Sensor 9201 in Ethernet the operation will work immediately If you operate it through the Internet the response speed depends on the situation of the network Normally the delay is not obvious because the date need to be transported during operating the IP Sensor 9201 is very little 25 VER X X
3. As setting up the receiver e mail address IP Power will send its IP Address to receiver 19 VER X X 12345678 aked com 87654321 debe com ni ee e E abad 168 com Setting Sample Receiver 12345678 abcd com 8765432 1 dcba com Sender abcd 168 com Mail Server 168 com Mail Password 9 00000 Warning MSG Alert After type in all the information please click apply first to save the change and then send to send mail There is status bar next to at the clock There are four possible situation for sending e mail 14 00 03 Mail send OK a Mail send OK Receiver should receive mail in short time b User or password error After change the username and password please click apply To save setting and click send to c Mail ahead sending please send later Mail server was block as lots mail d Connect time out mail to be dropped please login again 1 Receiver can be 2 receiver e mail address please use space between two e mail address After setup ever time you login IP Power 9212 will send receiver the IP address 2 Mail Server must be a mail server which can supply e mail transfer and support SMTP function 3 Warning MSG the title of the e mail 4 The maximum digits of each item 20 IP POWER 9212 USER MANUAL a Receiver 0x200 512 bytes b Sender 0x30 48 bytes c Server 0x30 48 bytes d Password 0x30 48 bytes e Warning MSG text 0x50
4. 80 bytes can be empty 5 Mail contents include From To Subject IP Family Address GPRS for Cell Phone Support WAP IP POWER 9212 support GPRS function you can use cell phone with online function To setup the online device real IP address as operate in browser 1 Address setting add wap after your online IP address For example http 65 59 37 123 wap or appointed port http 61 59 32 147 8080 wap the interface is same as in IE Internet Explore 2 The IP Address must be real ip address and can be work on Internet 3 The name of IP device must be English or will be encode in wap 4 Before using WAP control please check if your cell phone support GPRS and 1f your number had apply online service We support Motorola V878 Sony Ericsson T630 and Siemens Software online update For wild application in different filed IP POWER 9212 support online update It safe time and money as developing your product Step 1 Login the webpage Step 2 Click Firmware Update and click update svstem Firmware Update After pressing the Update button please wait while the update request is being processed After update is completed the device will reboot automatically You can re login afterwards a Firmware Update Step 3 Click browser to use latest Firmware then click Upgrade to update Firmware M ktip 1192 150 0 1007 Microsoft Internet Explo
5. circuit between the two connects is turn off 1 Auto test function 15 VER X X 3 i hl 1 E 0 ee i gt a F a E Click the test itself button and you will see the figure above The states of OUT1 OUT2 OUT3 and OUT4 will separately keep in ON for 1 second 3 seconds 6 seconds and 8 seconds then all back to OFF After one period four outputs will keep in OFF state for the same time This process will repeat until you click the reset or cancel button 2 Set the output s state to ON OFF Click the output you want to change set it to ON or OFF state and click apply button to finish the setting B 11 LE a r i SAAR 2 PILA El de i a 3 Set one output be in ON OFF state at the appointed time You can set the state when one output starts either ON or OFF You can also set the delay time and the action when the delay time is up Then click apply button to confirm it The example shows in the figure above means the OUT3 will be in ON state when it starts and will changes the state to OFF after 30 seconds 4 Reset the ON OFF settings Click the reset button you can cancel the previously output settings 16 IP POWER 9212 USER MANUAL Setting the password for IP Power 9212 Click the change password option at the left window and you can enter the change password page Follow the instructions fill in the old password and new password then click the apply button to confirm 1
6. easily control devices remotely and check the device status via the Internet anywhere in the world Using a Browser such as Internet Explore or Netscape you can securely access the unit It includes 8 Digital Inputs 8 Digital Relay Outputs and works like an IO Server You can integrate it with Home Office security Personal entertainment and Industrial field applications The API program is supported to help the integrator to easy program any software to integrate with existing application systems in local computers The IP POWER 9212 can be flexibly applied to Home entertainment amp industry security amp systems with integrated management Feature 1 Embedded web server no need to connect to a PC Use Ethernet or Internet LAN WAN 2 Accessible with popular web browsers IE Internet Explore or Netscape DO NOT need specific S W 3 Comes with 8DI amp 8DO Direct control relay output DO and detects digital input DI 8 Set Sensor Default 4 Set Source mode Voltage Input and 4 Set Sink mode Resistance Input 8 Set Controllers Default 4 Set NO Normal Open amp 4 Sets NC Normal Close Network protocols supported HTTP DHCP Virtual and Dynamic IP Security code identification and Hardware reset function Easy installation setup and support with online upgrade Individual LED indicates switch working status 1 2 OL 5 Safe durable non electric leakage and anti farmable design 9 Polar protection
7. FACE DESCRIPTION ccscsvscscessvssseasostessasonsassosesieasnsensasvn sensosenccasaseovasbonsssatescasseseecsasooss 6 4 HARDWARE SOFTWARE INSTALLATION oemeovoosoosonsonoonoonooooosooonoeooesoeoosoeneenee 7 ID WARE INSTALLATION cds 9201 PRO HARDWARE CONNECT RECOMMEND erernee enne nee n eee mh 9202 PROHARDWARE CONNECT RECOMMEND cceeecceeeceeseeeeeeeeeeeeeenaeee tes SOPIWARE INSTALLATION 1 et islami a ala ta a a STINET TAL IZA AAA are iisa enion Aa alane iaaa eiiie arkali 12 BASIC SETTING THROUGH ETHERNE A naa miles 6 SETTING AND CONTROL THROUTH THE INTERNE T ccssssssssssssssssssssssees 14 SENSOR SETTINGS BOR 92 tao CONTROL SEIT TINGS FOR 92 ls PASSWORD SE TINGS FRO V2 Phare tei r r ENEA N ENO NEE EA ETANO Oh A m a E A SPECIAL AN TERSCONEROL 22s acroliecinas aia SPECIALAINTER C ONT ROL samateemaline pise SMTP FOR E MAIL INFORM IP ADDRESS amp SENSOR TRIGGER 0coocococccnnccncnnnccncons GPRS FOR CELL PHONE SUPPORT WAP 0 0 cece cece cee cece ceecceneeeucceenceueeces SOFTWARE ONDINE UPDATE Su sate cid kaateti kt rs 7 SETING 9202E THROUGH THE INTERNET eemeooeonsonsonooosoonoonooooonoooooooonoesoosooeoeee 23 8 APPLICATION ASSOCIATED TO OTHER IP RPODUCTS eemeosonoesenoonoosenooseesene 24 3 VER X X 1 Introduction The IP Power 9212 is a Network Controller amp Sensor with 8 DI amp 8 DO A specific PC or software is not needed you can
8. IP Power 9212 User Manual IP POWER 9212 USER MANUAL USER MANUAL IP POWER 9212 Version X X 2005 07 1 VER X X Warning any changes to this equipment without permission may cause damages to your equipment This equipment has been proved to can be prevented from the influence of harmful electronic jamming in normal business use condition IMPORTANT NOTICE 1 IP POWER 9212 is deigned to be used in door we have no responsibility for the possible damage in out door use especially in the rain 2 Please use the power adaptor provided by the dealer we have no responsibility for the possible damage in using other adaptors 4 Do not use IP POWER 9212 in strong shaking condition 5 Please contact the dealer If IP POWER 9212 works improperly Copyright 2004 All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of us All trademarks and products mentioned in this document are the properties of us Detector Gas Infrared Smoke SENSOR Movement detector Door Windows Remote Control Webpage IP POWER 9212 Controller Control Power device in Factory Office Sercurity system IP POWER 9212 USER MANUAL Table of Content 2 BEFORE YOUSTARE isas 5 PACKAGE CONTE nas aasal MINIMUM SYSTEM REQUIREMENTS edil SANTER
9. Setting a fixed IP address for IP Power 9212 Click the setup option in the left side of the window and you can enter the setting web page Then follow the instructions fill in the new IP address mask and gateway for IP Power 9212 forbidden the DHCP service click the submit button to confirm Notice 1 The format of IP Address xxx xxx xxx xxx yyyyy the port range of yyyyy is 1 32767 2 The range of Subnet Mask is XXX XXX XXX 0 Xxx xxx xxx 254 3 If disable DHCP you can set TCP Port and Default Gateway the default port of DHCP Enable is XXX XXX XXX Xxx 80 and the Default Gateway is supply by server 4 If use the port other than 80 you need to key full address http xxx xxx xxx xxx yyyyy in IE Netscape or use the attached program IPEditV3 exe to login 17 VER X X 5 When setup the setting please confirm the IP Address amp Controlled IP Address is same address Special Hardware Inter Control 92XX series Use 9201 9212 DI part to control IP Power 9212 amp 9202 IP Sensor 9201 IP Motor 9203 1 92XX series Inter Control function Use DI Digital Input sensor device as main controller Like 9212 or 9201 to controlled device B like 9212 9202 9203 Correspondence connectors Main Controller SS S S S 9212 IN 3 IN6 PS E O O O KKK ES O device 9203 Turn left 1step Turn left 1step Keep turn left STOP left Main Controller S S S 9201 IN 1 IN3 Co
10. and the common user DO NOT try it For example L ight ball 1 Use the electrical wire of the equipment 9 VER X X Step 1 Cut offthe live wire Use a test pencil or screwdriver with voltage tester to identify the live wire between the two wires of electrical wire S L NOTICE this method must cut off the electrical wire of the household appliance Please make the decision after reading method 5 2 and 5 3 Step 2 Use a test pencil or screwdriver with voltage tester to identify the live wire between the two wires of electrical wire Cut off the live wire and connect to the port of IP Power 9212 Use the test pencil or screwdriver with voltage tester again to make sure the connection is correct NOTICE BE CAREFUL IN THIS OPERATION AND DO NOT TOUCH THE WIRE UNDER VOLTAGE WITH ANY PART OF YOUR BODY ESPECIALLY WITH YOUR HANDS 2 Use additional electrical wire you can buy some electrical wire and outlet in the electrical shop to cooperate with IP Power 9212 avoid cutting off the electrical wire of the equipment and can be used flexible in all kind of electrical equipment NOTICE Use a test pencil or screwdriver with voltage tester to identify the live wire between the two wires of electrical wire and make sure of connecting the live wire to the port of IP Power 9212 IP POWER 9212 USER MANUAL 3 You an control multi power by use the power extension cord NOTICE Do not connect too much energy intensive e
11. ess Please follow the steps below to change the subnet of your PC 12 IP POWER 9212 USER MANUAL 3 If can not get in the 92XX web page please set the segment of IP 9060 A to be same as your PC You can get your PC network information IP Addres Subnet Mask and Default Gateway by step start gt execute gt key cmd in dialog gt key ipconfig in MS DOS mode es CAVWINDO WSS ystem32temd exe icrosoft Windows XP hat 5 1 2600 CC Copyright 1985 2681 Microsoft Corp G Documentzs and Settings Chiu ipconfig Mindows IP Configuration Connection specific DHS Suffix IP Address Subnet Mask Default Gateway 192 168 104 31 299 299 209 192 168 100 254 GC Documents and Settings Chiu gt The last digit of IP address can be any number between 1 254 but can not be same as your PC If using in any PC just use HUB and type the 192 168 0 100 in Browser or use ipedit exe then you can get in the webpage Same SEGMENT The first 3 number of IP address is same XXX XXX XXX abc The part of XXX is same Fro Example IP address is 192 168 1 100 then another IP address 192 168 1 123 is the IP in same segment 4 The default username and password of IP Power 9212 are Username admin Password 12345678 If forget the new password you can key in superuser in username and hardware reset the device to set the default setting Password 12345678 for security co
12. he address bar of IE browser in any PC connected to the Internet network You can control the 9202E by typing 192 168 0 3 in the address bar of IE in any PC in the Ethernet 93 VER X X 8 Associated with other IP network product You can associate the IP Power 9212 with other IP network product of OUR in your home Ethernet such as IP Kamera 9000 network camera IP Video 9100 network video server and IP Sensor 9201 IP POWER 9202E to monitor the equipments or sensors installed in the doors or windows This is an economic solution to achieve the network monitor detection and control Light Glass Smoke Temperature Other 9000 j i Lontrol 1 Detector Brake lri Detector Detector Series Sere as est MO J L l E E kas Detectar m i a De tint bor Ss ee genie Infrared Remote Detector Control 2 Switch Q201E Sense Video CH 4100 KA TI g E a Come rad Air Water Other 9000 c kl i Candi tion Rice Heater Washing Series antros T Cooker fis w Machine m J y A tte JE OXXX KEK Remote Control 2 2 ul _ Heater E AA JA Monitor Screen o 1 an coo pin ioe e E i 24 IP POWER 9212 USER MANUAL 9 FAO Q1 I forgot the password and can not enter the administration page now what can I do A1 Turn on the power normally and then click the ipedit exe program to enter the web page Type m the username
13. lectrical equipment such as air conditioner electrical heater microwave over or over in the same electrical outlet Too much electrical currency may cause fire This product not guaranties the possible damage because of too much electrical currency Software installation Having connected the power supply and network cable with RJ45 port to the 9200 please install the software as the follow steps 1 Start your computer put the install disc in the CDROM and then find the file named ipeditv3 exe in the install disc 2 Copy the file to desktop or any directory you want save to 3 Start the initial setting process following the construction in next section NOTICE IP Power 9212 needs not any driver of application software its entire operation interface is built in its hardware Ipeditv3 exe can find the virtual IP address for you 5 Initial Settings Initial settings through the Ethernet 1 Double click the IPEditV3 exe 11 VER X X Bea Camera lists HE 500500 a ranar Submit Tow cae change canes mae PP dere get Geter A it Ge ee ae Ciasta Poe TIAL Lo sake chispa i CAMS FA meters GP EE aoj Epimepii on Tig l edit bos 1 Press Seat L bittan er Ester j Press Fpdate to rescom the ipatellod Mars 2 All the IP 92XX series IP Kamera 9000 series IP Video 9100 series in the same subnet of the Ethernet will be found and be display in the window by the software The default name of IP Senso
14. n 3V when it shows OFF and higher than 4V when it shows ON 2 The maximum measure voltage is 24V Slink mode Resistance Input IN5 IN8 contacts are short circuit sensor If the resistance between the two contacts in one set within 0Q 200Q 9212 shows ON If the resistance within 500Q co 9212 shows OFF So user can detect the movement of equipment through the magnetic reed switch or other kind of reactive sensors NOTE 1 The data in this figure is the average measure value To ensure the correct detection we suggest user set the voltage lower than 200Q when it shows ON and higher than 500Q when it shows OFF 2 When measure the resistance of web contacts the maximum voltage is 5V and the maximum currency 0 A WE Su is no more than 10mA ON OFF PS magnetic reed switch using the magnetic field of the magnet to produce a signal when there is a movement happened in switch Low cost and easy to use 1s the chief characteristic of magnetic reed switch Most of them are used in security equipment living product and automatic mechanism 9202 Pro Hardware connection recommend IP Power 9202 Pro offers 4 sets of NC Normal Close Out 1 Out 4 4 sets of NO Normal Open Out 5 Out 8 Maximum Rated Voltage 240V AC 60V DC Maximum Rated Currency 12A AC DC Maximum Switch time Max 10ms Environment Temperature 30 C 55 C NOTICE Only the professionals should operate the following operations in this section
15. ncern 5 Please refer software Infinity Cam to use IP Power IP Sensor IP Kamera amp IP Video in one video screen 6 Note if stay for long time as in webpage you would be unable setting and see message Cookie time out please go to IE to change setting Tools gt Internet operations please click Delete Cookies and Delete files in Temporary Internet file Temporary Intemet files 13 VER X X 6 Control and settings through the Internet Type the new IP address of IP Power 9212 in the address field and you can enter the login web page Input the default password 12345678 you can change the password as you wish click the OK and then you can enter the Web Control page 1 Maximum 8 digit for Password Welcom to IP Power WebControl Please enter password maximum 8 User Name admin 00000 Password Cancel de ae Ts ME ait 2114 ITT A m j TA 6 s A Cancel Testitelf Sensor of IP Power 9212 Read IO Source mode Voltage input IN1 IN4 contacts are active signal sensor If the voltage difference between the two contacts in one set within OV 3V 9212 shows ON It the voltage difference within 4V 24V 9212 shows OFF So user can detect the change of equipment Such as smoke detector light detector and gas detector Sink mode Resistance Input 14 IP POWER 9212 USER MANUAL IN5 IN8 contacts are short circuit senso
16. ntrolled device 9202 IN 9212 IN l IN2 IN3 IN 4 X l IN 3 IN 6 INS X 2 Connect Client setup A Divide this device word separate ly and do not use Inter Control 18 IP POWER 9212 USER MANUAL B Light This device can control 9202 9212 IP Power by change the default setting of Normal close or normal open C Motor This device can control 9203 1P Motor control the direction of turning 3 Controlled IP Address Setting the Ip Address of controlled device In Inter control mode when transfer the Out Light P6 1 P6 2 will always on if the main controller freeze the Out Light P6 1 is always on if the controlled device freeze the light of P6 2 is always on 2 1 For example Control Ip Motor by DI board of IP Power 9212 Step 1 Goto SETUP change Connect Client and set as Motor Step 2 key in the IP address of controlled device IP Motor Connect Client O Divide O Light Motor Controlled IP Address pane be LSE 09 al Es Product Name IP Power 9212 Pro Step 3 Click Submit to confirm setting when the count windows is off the new login windows jump out as following pictures Welcom to IP Family WebControl Please enter password maximum 6 Wiser Mame admin Password Cancel SMTP for E Mail receive IP address amp inform as Sensor trigger IP Power can setup the e mail address for receive change from sensor part
17. of voltage signal IN1 IN4 and four sets of shortcut circuit signals IN5 IN8 9201 Pro provide 4set Source mode Voltage Input Out 1 Out 4 ON 4V 24V OFF 0V 3V 4 set Sink mode Resistance input Out 5 Out 8 ON 200 ohm 0 ohm OFF 500 ohm 1 The polarity Right Positive amp Left Negative Left Negative Right Positive 7 VER X X NOTE Because of the polarity protective function it won t damage the product if you reverse the polarity in installation But it will cause the product cannot work properly 2 Source mode Voltage signal IN1 amp IN4 can be connected to voltage signal detectors such as smoke detector light detector and gas detector 3 Sink mode Resistance signal IN5 amp IN8 can be connected to magnetic reed switch as the follow figures It can be installed in the entrance guard or security equipment such as doors windows drawers and safe case Derectors mon IP POWER 9212 USER MANUAL Source mode Voltage input IN1 IN4 contacts are active signal sensor If the voltage difference between the two contacts in one set within OV 3V 9212 shows ON It the voltage difference within 4V 24V 9212 shows OFF So user can detect the change of equipment Such as smoke detector light detector and gas detector NOTE 1 The data in this figure is the average measure value To ensure the correct detection we suggest user set the voltage lower tha
18. r 9212 is IP POWER IPEditV3 can adjust Name Gateway IP Netmask HTTP Portl Hame 12345678 Estevsy 192 168 100 254 IP Netma k HTTP Porti 30 HTTP Port 0 MAC 00 90 00 00 08 53 2 1 Change Name MAXIMUM 10 DIGIT 2 2 After Change Gateway IP Netmask xxx xxx xxx 0 Xxx xxx xxx 254 or Portl 1 32767 the device will turn off DHCP 2 3 Click the IP in Lists will open the webpage please type the IP Address if using Netscape 3 Click the equipment s name that you want to edit in the left of the window it will turn fuscous the equipment s name and IP will display in the windows you can rename After that click the update button and the new setting will be work in 20 seconds 4 Double click the name of the equipment you want to control the IE browser window will open and connected to this equipment in that Ethernet automatically You also can type the IP address of the 9212 in the IE browser to open the web page of 9000 We suggest you to update the IE to version 6 0 with SP1 or above if your IE notices you the security level is too low to open that web page NOTICE 1 Make sure the RJ45 network wire have been connected correctly and the 9212 are power on 2 It can obtain the virtual IP address after you run the ipeditv3 exe only if the Ethernet support DHCP Click the IP address to enter the web page If the Ethernet not support DHCP IP92XX will change it s IP address to fixed IP addr
19. r If the resistance between the two contacts in one set within 0Q 200Q 9212 shows ON If the resistance within 5000 00 9212 shows OFF So user can detect the movement of equipment through the magnetic reed switch or other kind of reactive sensors NOTE 1 The data in this figure is the average measure value To ensure the correct detection we suggest user set the voltage lower than 200Q when it shows ON and higher than 500Q when it shows OFF 2 When measure the resistance of web contacts the maximum voltage is 5V and the maximum currency 1s no more than 10mA Click the refresh button and you will see the similar figure like this It represents the state of the four sets of input signals there may be some delay it up to your network You also can press the check button in the PCB of 9212 click the refresh button in the web page at the same time and then observe whether the input signal state shows ON in the web page Control of IP Power 9212 SET IO IP Power 9212 now can control 8 outputs at the same time Out1 amp Out4 are normal close switches When it is on the corresponding LED lights up the circuit between the two connects is turnoff When it is off the corresponding LED light off the circuit between the two connects 1s turn on Out amp Out8 are normal open switches When it is on the corresponding LED lights up the circuit between the two connects is turn on When it is off the corresponding LED light off the
20. rating system IE5 0 SP1 Minimum 64MB RAM VGA Card with capability of displaying full Colors and DirectDraw support Network card with RJ45 port Ethernet Hub Router Internet network Ethernet xDSL or other ways depends on whether you need far end control ability or not 5 VER X X 3 Interface Description IP Power 9212 has three devices 9200 is the network module and the followed picture shows its interface 9202 is the output module and figure below shows its interface 9202 is the output module and figure below shows its interface IP POWER 9212 USER MANUAL 4 Hardware amp Software installation Before you star to use IP Power 9212 please follow the steps below NW Check the package to make sure the contents is complete MW Prepare one Ethernet HUB or Router HW Check the voltage of the power supply to make sure it is AC 110 240 volt Hardware Installation Connect RJ45 first then POWER jack 1 Connect the 9200 to HUB through RJ 45 netting cable 2 Connect the 9200 IN to 9201 amp 9200 OUT to 9202 through D SUB cable Please connect 9200 D SUB IN to 9200 IN port amp 9200 D SUB OUT to 9202 OUT port 3 Connect the HUB to the Internet May through ADSL XDSL modem 4 Connect the power adapter to the 9200 Power on your computer and power adapter of IP POWER 9212 9201Pro Hardware connection recommend For different request of normal state of electric equipment 9201 offers four sets
21. rer SED BE SAT AE TAD KHE 3 1 gt 03 Oma grant a amp SUD 8 k igi 1680 1005 Upgrade Firmware VER X X Plaase select a fila bin to upgrade Cimosy MF lg bin 00 Step 4 after finish update please wait some second and then re log In 3 Aether ore pl Hicrosofi A htp 11192 168 0 100Agifo0p grade tgi Micros SEE Gy 8827 Ber IA G O ABE E fd Oit B 901 168 0 pea BRE REE BRO Oo iu TE O 0 PAAL FED El htip 192 168 0 100 tgi opgrade tei Please wating a minute and click button bo next step gt Please wating a minute and click button to next step Fe Login PS If use DHCP please enable DHCP Note 1 If the Portis80 then you can directly update 2 If update fail you can manual reset the device and update again 7 Setting the 9212 through the Internet 22 IP POWER 9212 USER MANUAL After you have setting the Ethernet and router you can access the IP Sensor 9212 from the Internet It will bring you all kinds of convenience After assigning them different IP address and mapping to each port of the router you can visit each equipment through the Internet network Air conditioner Washing machine Monitor at the far end 192 166 0 1 If you have mapped one port for example 85 of the public network IP XXX XXX XXX XXX to the IP 192 168 0 3 in the Ethernet you can control MAT TE E the 9202E by typing 192 168 0 3 in t
Download Pdf Manuals
Related Search