Netgear WN370 Installation Guide
Contents
1. Slow blinking amber The access point is not managed by a wireless controller Green The access point has successfully booted and is managed by a wireless controller Power D Activity a Blinking Green There is network traffic through the access point Off There is not network traffic through the access point WiFi On Off Solid Green The access point s WiFi is active Off The access point s WiFi is off Note If you cannot connect see Troubleshooting Tips in this guide NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject to change without notice NETGEAR Inc All rights reserved For indoor use only Valid in all EU member states EFTA states and Switzerland January 2014 NETGEAR Inc 350 East Plumeria Drive 201 17821 04 San Jose CA 95134 USA Troubleshooting Tips Here are some tips for correcting simple problems you might have The WC7600 Cannot Discover or Manage the Access Point If the WC7600 cannot discover or manage the access point you can log in to the access point to troubleshoot and download the system log NETGEAR support will use the system log to help diagnose any problems with the access point Note The WN370 has DHCP enabled by default and receives an IP address if you2. NETGEAR Installation Guide ProSAFE Wall Mount Access Point WN370 Package Contents Unpack the box and verify the contents e ProSAFE Wall Mount Access Point WN370 e Mounting bracket with four mounting screws e Warranty card e Software license agreement e Regulatory flyer e Installation Guide Installation Requirements You must have the following items to successfully install your access point e A6mm Phillips screwdriver e AT8 screwdriver e Acomputer running Windows XP or Windows 7 e A Standard EU or US wall outlet junction box with an ethernet cable routed through the wall from your LAN to the junction box e An IEEE 802 3af at compliant PoE switch or IEEE 802 3af at compliant PoE injector Mount the Access Point The access point requires an electrical outlet junction box mounted in a wall To mount the access point to the wall 1 Remove the faceplate from the outlet junction box 2 Run the Ethernet cable through the junction box with enough slack to reach the access point 3 Run the Ethernet cables through the mounting bracket 4 Align the mounting bracket with the holes on the junction box 5 Attach the mounting bracket to the junction box using the included Phillips head screws 6 Connect the Ethernet cable providing PoE and network connectivity to the PoE port on the back of the access point for SIMI MAY 7 Optional Connect the Ethernet cable providing pass thr
3. have a DHCP server in your network If you have a DHCP server in your network use the address assigned to the WN370 to log in to the access point To log in to the access point and download the system log 1 Configure a computer with the following IP options e IP address 192 168 0 22 e Subnet mask 255 255 255 0 e Default gateway 192 168 0 1 2 Enter http 192 168 0 160 or your access point s assigned IP address into a browser 3 Log in to the access point using the following default credentials e ID admin e Password password 4 Click Monitoring gt Logs 5 Click the Save As button 6 Send the log to NETGEAR support The Power LED is Solid Amber After Five Minutes There has been a boot up error and the access point needs to be reset To reset the access point 1 Remove the access point from the wall without disconnecting the Ethernet cable 2 Press the reset button on the back of the access point for at least five seconds 3 Mount the access point to the wall 4 Follow the procedure for discovering the access point Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at hitps my netgear com NETGEAR recommends that you use only the official NETGEAR support resources You can contact NETGEAR tech support representatives via chat e mail or phone support at http support netgear co
4. m general contact default aspx For the current EU Declaration of Conformity visit http support netgear com app answers detail a_id 11621 For regulatory compliance information visit http Avww netgear com aboul regulatory
5. ough support to the pass through port on the back of the access point 8 Mount the access point to the mounting bracket using the included T8 screws LZ LAA Za a F Z w Z Z Z Z Z A a IT Z Zz Z Z Ney Z Ba Z Set Up the Access Point The WN370 access point can only be deployed in a network managed by a ProSAFE WC7600 wireless controller If you have a DHCP server in your network option 43 must be enabled pointing towards the IP address of the WC7600 To discover and configure the access point using the WC7600 wireless controller 1 Access the wireless controller at the network IP address that you configured 2 Select Access Point gt Discovery gt Discovery Wizard 3 Follow the steps onscreen to discover the access point and review the discovery results 4 Select Access Point gt Discovery gt Managed AP List Add the access points that you want to be managed by the wireless controller to the Managed AP List Note For extensive information about the Discovery Wizard and the discovery process see the WC7600 reference manual Verify Wireless Connectivity Using a computer with an 802 11b g n wireless adapter verify connectivity by using a browser to connect to the Internet or check for file and printer access on your network You can also check the access point LEDs to verify a successful installation and connection LED Description Solid amber The access point is booting
Download Pdf Manuals
Related Search