Home

Netgear WN3100RP User Guide

1. gt 1 a eo J g a g is 5 ss i n G E i W GA n France Germany Figure 1 Extender appearance varies according to country or region How the Extender Works The extender works like a bridge between a wireless router or gateway and a computer or wireless device outside the wireless router s or gateway s range To do this the extender has two main jobs e The extender connects to a wireless network that is running When the extender connects wirelessly to a network it acts as a network client This is similar to how a computer connects to a network e The extender acts as an access point for computers The extender has its own wireless network called NETGEAR_EXT that wireless computers can join In its role as an access point the extender performs tasks that wireless routers or gateways do such as broadcasting its network name SSID Getting Started 6 Universal Pass Through WiFi Range Extender WN3100RP The extender must do each of these jobs so that both ends of the bridge are in place When to Use Your Extender NETGEAR recommends that you connect to the extender only when your home network connection is poor Because data traffic routed through the extender is inherently slower than traffic routed directly from the network the computer should stay on the network if the connection is good enough NETGEAR recommends that you connect through the extender network onl
2. Universal Pass Through WiFi Range Extender WN3100RP A screen similar to the following displays pe eaa Select the name of your existing network Device to Extender Apply Settings j SSID Channel Signal Security squinch 1 90 WPA2 PSK 2NTGR125 8 53 WPA2 PSK HOME670 2 16 WPA PSK AquaDeer 4 6 WPAMWPA2 PSK AquaDeer quest 4 5 OFF Manually input my wireless SSID This is the same Smart Wizard that displays during installation as described in the installation guide 3 Select the network from the list that you want to connect to and click the Continue button 4 A screen similar to the following displays Enter the security settings of the selected WiFi network Device to Extender j Apply Settings Name SSID 2NTGR125 Security WPA2 PSK AES Passphrase 5 Enter the passphrase for your wireless network and click the Continue button A screen similar to the following displays ea r to Routor Enter the settings for the Extender network Apply Settings J Name SSID 2NTGR125_EXT Use the same security mode and password as those for the existing network The extender s wireless network name SSID changes to the name of your wireless network with EXT added to the end 6 Make sure that the correct network name is shown and then click the Continue button Getting Started 19 Universal Pass Through WiFi Range Extender WN3100RP The extender connects to your existing wireless network A screen simi
3. Getting Started 11 Universal Pass Through WiFi Range Extender WN3100RP e Product label The product label provides access information WPS PIN serial number and MAC address NETGEAR Universal Pass Through WiFi Range Extender WN3100RP rower YP wes Paco gt DEFAULT ACCESS Router Direction Client http mywifiext net User Name admin Pas INDOOR USE ONLY Arrows Default access information 200 250V 0 3A 50 60Hz Product Only 16A Maximum Load WPS PIN WPS PIN Serial number MAC address MAC SERIAL Made in Vietnam 272 11932 03 Antennas For best performance position the antennas pointing up Antennas Figure 6 Proper antenna orientation Extender Port Connection Usually you connect to the extender wirelessly but you can connect equipment such as a computer TV Blu ray player or gaming console to the Ethernet port on the extender Note Before you connect wired devices or computers first install and set up your extender as described in the Universal Pass Through WiFi Range Extender WN3100RFP Installation Guide that came in the package Getting Started 12 Universal Pass Through WiFi Range Extender WN3100RP Range extender in the family room Wireless router p in a home office ar Access the Internet with a Blu ray player Figure 7 Ethernet port connection gt To connect a computer to the extender with an Ethernet cable 1 Connect
4. 2NTGR125_EXT Region Europe Channel 8 P 4 S Wireless mode Up to 300Mbps Wireless AP On Broadcast Name On s r e m ome Help Center Show Hide Help Center vr Help amp Support Documentation Online Support Device FAQ Sy NOt a Enter Search Item 2 View the current settings and the status of your extender e Hardware and Firmware Version The model of the hardware and the currently running firmware version e GUI Language Version The currently selected language e Connection status to Existing Network Name SSID Your extender is set up to connect to this SSID also called the wireless network name Extender Network Settings 31 Universal Pass Through WiFi Range Extender WN3100RP Link Rate The actual transmission Tx and receive Rx link rate in the current wireless connection Connection Status The status of your wireless connection connected or disconnected e Extender IP Info MAC Address The physical address of the extender as seen from the local area network LAN IP Address The IP address of the extender The default is 192 168 1 250 DHCP Client The network DHCP client on the wireless network IP Subnet Mask The IP subnet mask associated with the LAN IP address of the extender The default is 255 255 255 0 Gateway IP Address The IP address of the wireless network gateway Domain Name Server The IP address of the Domain Name Server DNS of the wireless netwo
5. NETGEAR genie WN3100RP Extender to Router Device to Extender Apply Settings 4 Follow the steps to connect the extender to the WiFi network When the extender connects the Router Link LED lights Getting Started 15 Universal Pass Through WiFi Range Extender WN3100RP 4 If the network is secure the WPS LED lights green New Extender WiFi Network Name The first time the extender connects to a WiFi network the extender WiFi network name SSID changes to that network name with EXT at the end For example e WiFi network name MyNetworkName e Extender network name MyNetworkName_EXT If the extender does not connect to the WiFi network move the extender to a different location with a better WiFi signal For example you might need to move it closer to the router or gateway Join the Extender WiFi Network After you install the extender you can connect your clients to the extender WiFi network To join the extender network 1 Take your computer or wireless device to the location with poor WiFi coverage 2 Find the new extender network name MyNetworkName_EXT 3 Select this network and enter the same WiFi password that you use for your home network 4 Within two minutes check the arrow LEDs on the extender e If no arrow is lit the location is good e When the extender connects to a network and a client joins the extender network a blinking arrow LED indicates whether the extender is to
6. Address O00 FF FF FF FF FF IP Address 192 168 0 10 gt Advanced DHCP Client ON IP Subnet Mask 255 255 255 0 Gateway IP Address 192 168 0 1 Domain Name Server 192 168 0 1 Extender Wireless Setting Name SSID 2NTGR125_EXT Region Europe Channel 8 P 4 S Wireless mode Up to 300Mbps Wireless AP On Broadcast Name On s r e m Help Center Show Hide Help Center Help amp Support Documentation Online Support Device FAQ SiT 04 ae Enter Search Item vr Use the Smart Wizard to Change the Settings The Smart Wizard can help you set up your extender to connect to a wireless network For information about more configuration options see Chapter 2 Extender Network Settings The Universal Pass Through WiFi Range Extender WN3100RFP Installation Guide included in the package explains how to install your extender During installation when you launch your Internet browser the Smart Wizard automatically displays After installation you can change the extender network settings if you want For example if you change your network name you can log in to the extender and change its network name to match gt To use the Smart Wizard again after installation 1 Log in to the extender For more information see Log In to the Extender on page 17 Note Once you begin using the Smart Wizard you must complete all of its steps before you can exit 2 From the menu select Setup Wizard Getting Started 18
7. Extender Settings n nnana anaana anaana 34 Set the PaSSWO 653cinaroncee netti eens Aoake enka Aei a A a 35 Update the Firmware nananana aaea 36 Advanced Wireless Settings n nnana anaa aaa 37 Chapter 3 Troubleshooting Smart Wizard FAQS oid ode eh ei aaaea O4 eS oY OKO bow RESO 40 Connecting to http mywifiext net 0 0 0 0 0c eee 40 Universal Pass Through WiFi Range Extender WN3100RP Joining Wireless Networks Appendix A Supplemental Information PCO Ooo ao aa pate ea pate oe Ae ae ae od ek eet re eee oe eee Technical Specifications Safety Information Appendix B Notification of Compliance Getting Started This chapter covers the following topics e Get to Know the Extender e Hardware Features e Install the Extender e Log In to the Extender e Restore Factory Settings For more information about the topics covered in this manual visit the support website at htto support netgear com Universal Pass Through WiFi Range Extender WN3100RP Get to Know the Extender The Universal Pass Through WiFi Range Extender lets you extend WiFi coverage to locations outside the range of your wireless router or gateway e Arrow LEDs on the front of the extender help you find the best location for the extender e With the extender pass through socket you retain the use of a socket in your electrical outlet The appearance of the extender varies according to country or region lt
8. Hide Help Center 2 Do one of the following e To back up your settings click the Backup button Your browser extracts the configuration file from the extender If you do not have your browser set up to save downloaded files automatically locate where you want to save the file You can give the file a meaningful name at this time such aS internet_adapter cfg e To restore your settings select the previously saved backup file and click the Restore button A screen displays that lets you know the device has been successfully restored to the previous settings The extender restarts This procedure takes about one minute CAUTION Do not try to go online turn off the extender shut down the computer or do anything else to the extender until it finishes restarting e To erase the settings click the Erase button Extender Network Settings 34 Universal Pass Through WiFi Range Extender WN3100RP Under some circumstances for example if you have lost track of the changes that you made to the extender settings you might want to erase the configuration After an erase the extender returns to its factory settings see Factory Settings on page 43 CAUTION Do not try to go online turn off the extender shut down the computer or do anything else to the extender until it finishes restarting Set the Password The user name to access the extender is admin and its default password is password NETGEAR strongly recommend
9. and to help protect your product from potential damage To reduce the risk of bodily injury electrical shock fire and damage to the equipment observe the following precautions e The socket outlet shall be installed near the equipment and shall be easily accessible e Observe and follow service markings e f any of the following conditions occur unplug the product from the electrical outlet and replace the part or contact your service provider retailer The power cable extension cable or plug is damaged An object has fallen into the product The product has been exposed to water The product has been dropped or damaged The product does not operate correctly when you follow the operating instructions e Keep your system away from radiators and heat sources Also do not block cooling vents e Do not spill food or liquids on your system components and never operate the product in a wet environment e Do not push any objects into the openings of your system Doing so can cause fire or electric shock by shorting out interior components e Operate the product only from the type of external power source indicated on the electrical ratings label e Also be sure that attached devices are electrically rated to operate with the power available in your location e Use only approved power cables If you have not been provided with a power cable for your system or for any AC powered option intended for your system purcha
10. client PIN in the field that displays Push Button recommended PIN Number This is the security PIN of the WPS client While connecting WPS enabled adapters provide a randomly generated security PIN Enter Client s PIN Next Help Center x Show Hide Help Center The extender tries to find the wireless client the computer that is attempting to join the network If you are using a WPS button it tries for two minutes If you are using a PIN it tries for four minutes 4 Use the WPS software on your wireless computer to connect to the extender The first time you add a WPS client WPS automatically sets the extender s wireless security to WPA2 WPA with a random passphrase You can view these settings in the Wireless Settings screen For more information see Extender Wireless Settings on page 27 Extender Wireless Settings You can use the Wireless Settings screen to change the network name SSID for the extender s network and to set up wireless security If you do not change these settings the network name is NETGEAR_EXT and the network is open no wireless security is set up Note If you use a wireless computer to change the extender s wireless settings you are disconnected when you click the Apply button To reconnect you must select the new network name that you created and enter the passphrase or wireless security key that you set up gt To change the wireless settings for the extender n
11. cross sectional area Do not plug devices into the Universal Pass Through WiFi Range Extender WN3100RP filtered AC outlet that exceed the product ratings The output voltage of the filtered AC outlet is the same as the power outlet that the Universal Pass Through WiFi Range Extender WN3100RP is plugged into To help avoid damaging your system be sure that the attached devices are electrically rated to operate with the power available in your location If the input AC voltage is less than 100 VAC the device plugged into the filtered AC socket of the Universal Pass Through WiFi Range Extender WN3100RP might not perform as well as expected DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip The device is not intended to be used with home appliances such as air conditioners power tools space heaters fans hair dryers ovens or refrigerators Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Do not service any product except as explained in your system documentation Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you to electrical shock Only a trained service technician should service components inside these compartments Use the product only with approved equipment Allow the product to
12. is the name of your wireless network with _EXT added to the end Select the My wireless devices are connected to the Extender network Selecting this checkbox activates the Continue button check box and click the Continue button A screen similar to the following displays Extender to Router Device to Extender j Apply Settings Congratulations The Extender has successfully connected to your existing network Within 2 minutes after the extender connects to the router or gateway and a client check the Arrow LEDs on the extender to see if they are blinking A blinking arrow means that you should move the extender to a different location for better WiFi performance If the extender is in a good location for WiFi performance the Arrow LEDs do not blink Left Arrow LED is blinking me OD Move the extender closer to the router or gateway If that is not possible try to improve the line of sight between the router and the extender Right Arrow LED is blinking aco wb Move the extender closer to the location of the client the wireless computer or device that is using the extender WiFi network 10 Click the Finish button When You Travel The extender makes it easy to connect your laptop tablet and smartphone to an Internet connection at a hotel or WiFi hotspot At some hotels or hotspots you might be prompted to enter the password for the Internet connection Getting Started 20 Universal Pass Through WiF
13. 47
14. D g 0 5 IG S S p lt 4 On Off switch D O 53 M Plug the extender into a power outlet and wait one minute until the extender starts O The Power LED lights green 4 Connect the extender to your WiFi network a Connect the extender to your router or gateway For more information see Connect the Extender to Your WiFi Network on page 15 b Connect your clients to your extender For more information see Join the Extender WiFi Network on page 16 Getting Started 14 Universal Pass Through WiFi Range Extender WN3100RP Connect the Extender to Your WiFi Network Do not cable the extender to the router or gateway The extender connects to your wireless network only with WiFi You can use the extender s Wi Fi Protected Setup WPS or the web browser method gt To connect using WPS 1 Press the WPS button on the side of the extender ye 5 LAA 4 ev Ti go s n gt O s The WPS LED blinks 2 Within two minutes press the WPS button on your wireless router or gateway W The Router Link LED lights 4 The WPS LED lights green The extender network name changes See New Extender WiFi Network Name on page 16 gt To connect with the web browser method 1 On your computer or wireless device find and join the NETGEAR_EXT WiFi network ED The Client Link LED lights 2 Open a web browser 3 When prompted select a language from the list NETGEAR genie displays
15. Failure of the end user to comply with the applicable requirements may result in unlawful operation and adverse action against the end user by the applicable National regulatory authority This product s firmware limits operation to only the channels allowed in a particular Region or Country Therefore all options described in this user s guide may not be available in your version of the product Europe EU Declaration of Conformity Products bearing the CE marking comply with the following EU directives e EMC Directive 2004 108 EC e Low Voltage Directive 2006 95 EC If this product has telecommunications functionality it also complies with the requirements of the following EU Directive e R amp TTE Directive 1999 5 EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity For indoor use only Valid in all EU member states EFTA states and Switzerland This device may not be used outdoors in France For detailed information concerning installations in France the user should contact the national spectrum authority in France htto www arcep fr Radiation Exposure This equipment complies with radiation exposure limits set forth for an uncontrolled environment and meets radio frequency RF Exposure Guidelines This equipment should be installed and operated keeping the product 20 cm or more away from a person s body Notification of Compliance
16. NETGEAR Universal Pass Through WiFi Range Extender WN3100RP User Manual August 2013 202 11242 01 350 East Plumeria Drive San Jose CA 95134 USA Universal Pass Through WiFi Range Extender WN3100RP Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at hittps my netgear com You must register your product before you can use NETGEAR telephone support NETGEAR recommends registering your product through the NETGEAR website For product updates and web support visit htto support netgear com Phone US amp Canada only 1 888 NETGEAR Phone Other Countries Check the list of phone numbers at htto support netgear com general contact default aspx Trademarks NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject to change without notice NETGEAR Inc All rights reserved Table of Contents Chapter 1 Getting Started Get to Know the Extender 0 00 cee eee eee eee eee 6 How the Extender WorkS 0 0000 cee eee ee eee eee eee ee 6 When to Use Your Extender aana eee 7 Find the Best Location 0 0 00 00 cece ee ee ees 7 Use the Pass Through Power Socket 0000 cece 8 Hardware FeatureS 0 0 c
17. SK AES WPA2 is even more secure but some older computers do not support this standard When using wireless computers or devices that support WPA2 you can enter the passphrase to join the extender wireless network For more information see Set Up WPA WPA2 or WPA WPA2 on page 30 WPA PSK TKIP WPA2 PASK AES When using wireless computers or devices that support either WPA or WPA2 you can enter the passphrase to join the extender wireless network For more information see Set Up WPA WPA2 or WPA WPA2 on page 30 Click the Apply button Your settings are saved Use your wireless computer to connect to the extender network with its new settings The Smart Wizard guides you through this process Extender Network Settings 28 Universal Pass Through WiFi Range Extender WN3100RP Set Up WEP 1 Select Setup gt Wireless Settings 2 In the Security Options section select the WEP radio button 3 Select the authentication tyoe Automatic Open System or Shared Key The default is Open System Note The authentication is separate from the data encryption You can select authentication that requires a shared key but still leaves data transmissions unencrypted Security is stronger if you use both the Shared Key and WEP encryption settings 4 Select the encryption strength setting e WEP 64 bit encryption Enter 10 hexadecimal digits any combination of 0 9 a f or A F e WEP 128 bit encryption Enter 26 hexadecima
18. ardware Features The extender has features to connect it to your network and show how it is working Front and Right Side View The front and right side of the extender have LEDs the pass through power socket and an Ethernet port Pass through power socket Router Link LED i Right Arrow LED Left Arrow LED _ Tia E Client Link LED Power LED ty WPS LED Ethernet port J i i i h SK Md a y 7 G e Figure 4 Front and right side view The LEDs on the front show how the extender is working Sa Router Link This LED is lit when the extender is connected to the router or gateway Green The WiFi connection is good Amber The WiFi connection is fair Red The WiFi connection is weak 2 i Left Arrow This LED indicates the need to change the distance between the extender and the router or gateway Blinking blue Move the extender closer to the router or gateway Off The extender is close enough to the router or gateway H Right Arrow This LED indicates the need to change the distance between the extender and the client Getting Started 9 Universal Pass Through WiFi Range Extender WN3100RP Blinking blue Move the extender closer to the client Off The extender is close enough to the client e P Client Link This LED is lit when the extender is connected to the router or gateway Green The WiFi connection is good Amb
19. assphrase or key 4 Click the Continue button The extender joins your wireless network For information about how to monitor the quality of the connection see Monitor Extender Performance on page 17 Extender Network Settings 24 Universal Pass Through WiFi Range Extender WN3100RP Use WPS to Add a Computer to the Extender s Wireless Network Use WPS Wi Fi Protected Setup to connect a computer or wireless device to the extender network without entering the wireless network passphrase or key Instead you use a WPS button or enter a PIN to connect WPS supports WPA and WPA2 wireless security If your extender network is open and no wireless security is set then WPS automatically sets WPA2 WPA wireless security on the extender network You can connect with WPS by either of the following methods e Use the WPS button on the side of the extender e Log in to the extender and click the onscreen WPS button gt To use the extender WPS button to connect 1 Press the WPS button ev Foe ae Sa t Ow fa For two minutes the extender attempts to add a wireless client a computer or other wireless device to its wireless network 2 Within two minutes press the WPS button on your wireless device or follow the WPS instructions that came with your wireless device If your wireless device requests the WPS PIN of the extender you can get it on the product label of the extender Your wireless device is now connected to t
20. cc ee eee ees 9 Front and Right Side VIEW 26254562 cn0dee aueee gata sbbetueeens 9 Rear and Left Side View 0 000 ee ee eee 11 Antennas a a4e oa eaten op occa a ee eee Ra eh oe a eens 12 Extender Port Connection 444 24 ecccdis 2d based ee be detachecadd 12 Install the EXi ndel sss cccccaudtee4 4544584 405n0 005 OOSee a Eee 14 Place the Extender and Power ItOn 00 00 0000 ee 14 Connect the Extender to Your WiFi Network 00 15 New Extender WiFi Network Name 0 000000 eee 16 Join the Extender WiFi Network 0 0000 eee eee eee eee 16 Monitor Extender Performance 0 0000 ce eee eee eee eae 17 Log In to the Extender 2 4 cctcsi dane baad we eee A ae ew an 17 Use the Smart Wizard to Change the Settings 18 When You Travel 0 0 0 0 0c ee ee ee ees 20 Restore Factory Settings 0 065000 0800s esses eee ecuee 22 Chapter 2 Extender Network Settings Connect the Extender to an Existing Network 005 24 Use WPS to Add a Computer to the Extender s Wireless Network 25 Extender Wireless Settings 0 0 0c cc cece eee 27 TOT We a ce han Goh Oui ih ee eke ok Rae Gawd ae wy BHR ae 29 Set Up WPA WPA2 or WPA WPA2 2 0 2 0 00 cee eee 30 Extender IP Address Setup 0 0 0 ccc ee eee 30 Status Screen ee ee ee eee 31 Attached Devices 21224 2deGa sede deeee adeeb ibe cedaan beteedeens 33 Back Up and Manage
21. cool before removing covers or touching internal components To help avoid damaging your system be sure that the voltage selection switch if provided on the power supply is set to match the power available at your location 110 volts V 60 hertz Hz in most of North and South America and some Far Eastern countries such as South Korea and Taiwan 100V 50 Hz in eastern Japan and 100V 60 Hz in western Japan 230V 50 Hz in most of Europe the Middle East and the Far East Supplemental Information 44 Universal Pass Through WiFi Range Extender WN3100RP The peripheral power cables are equipped with three prong plugs to help ensure proper grounding Do not use adapter plugs or remove the grounding prong from a cable Observe extension cable and power strip ratings Make sure that the total ampere rating of all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip To help protect your system from sudden transient increases and decreases in electrical power use a Surge suppressor line conditioner or uninterruptible power supply UPS For additional safety instructions see Appendix B Notification of Compliance Supplemental Information 45 Notification of Compliance NETGEAR wireless powerline products Safety Instructions and Precautions WARNING Use the following safety guidelines to ensure your own personal safety
22. ct the Extender to an Existing Network Use WPS to Add a Computer to the Extender s Wireless Network Extender Wireless Settings Extender IP Address Setup Status Screen Attached Devices Back Up and Manage Extender Settings Set the Password Update the Firmware Advanced Wireless Settings 23 Universal Pass Through WiFi Range Extender WN3100RP Connect the Extender to an Existing Network You can connect the extender to your home network Only a wireless connection is supported The extender is not able to connect to your home network with a cable gt To connect the extender to an existing network 1 Select Setup gt Connect to an Existing Network The extender scans for wireless networks and displays a list Setup Wizard Select the name of your existing network Add WPS Client v Setup Connect to Existing Network SSID Channel Signal Security Wireless Settings squinch 1 IP Address Setup 2NTGR125 8 HOME670 2 gt Maintenance AquaDeer 4 gt Advanced Santos 4 Manually input my wireless SSID If your wireless network is not on the list and is running see Place the Extender and Power It On on page 14 for suggestions 2 Select the radio button for your network and click the Continue button A screen similar to the following displays Enter the security settings of the selected WiFi network Name SSID 2NTGR125 Security WPA2 PSK AES Passphrase 3 Enter your network s p
23. ed Devices Backup Settings Set Password Firmware Update gt Advanced Help Center 2 Click the Check button to see if new firmware is available Show Hide Help Center If it is follow the onscreen prompts to download the file onto your computer 3 Click the Browse button to locate and select the new firmware file that was downloaded 4 Click the Update button to install the new firmware on your extender Extender Network Settings 36 Universal Pass Through WiFi Range Extender WN3100RP AN CAUTION Once you start the firmware upgrade do not try to go online turn off the extender shut down the computer or do anything else to the extender until it finishes restarting Advanced Wireless Settings The extender is set up with the optimum settings Do not alter these settings unless directed by NETGEAR support Incorrect settings might disable the extender unexpectedly gt To view or change the advanced wireless settings 1 Select Advanced gt Wireless Settings The following screen displays gt Maintenance Wireless Settings v Advanced Wireless Settings Setup Wizard Advanced Wireless Settings gt Setup iv Enable Wireless Access Point vV Enable SSID Broadcast WPS Settings Device PIN 29055180 V Enable Device s PIN W To prevent PIN compromise auto disable the PIN after 3 failed PIN connections until device reboots In auto disabled mode device s WPS LED
24. er The WiFi connection is fair Red The WiFi connection is weak e Power This LED is lit when the extender is turned on Green The extender is on Amber The extender is powering up Off The extender is off e O Secure WiFi This LED indicates a secure wireless connection Solid green There is wireless security Blinking green The extender is establishing a WPS connection The front and right side panel have the following features e Pass through power socket You can use this socket to power other equipment e Ethernet port You can use this port for a wired connection to a computer or other device Getting Started 10 Universal Pass Through WiFi Range Extender WN3100RP Rear and Left Side View The rear and left side of the extender have the product label power connector and control buttons WPS button z Factory Reset button af Device On Off switch 9 A x A Power connector Figure 5 Rear and left side view The left side panel has the following features e Factory Reset button To use this button stick a paper clip into the reset hole and hold it until the Power LED flashes e WPS button Press the WPS button to wirelessly connect the extender to your router gateway or wireless adapter e Device On Off button Turns the device on and off The back has the following features e Power connector To provide power to the extender insert this connector into an AC wall socket
25. etwork 1 Select Setup gt Wireless Settings Extender Network Settings 27 Universal Pass Through WiFi Range Extender WN3100RP A screen similar to the following displays Setup Wizard Wireless Settings v Setup Connect to Existing Network My WN3100RP Wireless Network Name SSID 2NTGR125_EXT IP Address Setup Region ange gt Maintenance Security Options gt Advanced None WEP D WPA PSK TKIP WPA2 PSK AES D WPA PSK TKIP WPA2 PSK AES Security Options WPA2 PSK Passphrase YourPasswordHere 8 63 characters or 64 hexdigits Help Center gt Show Hide Help Center In the Name SSID field type a new name to customize your extender network In the Region field select the region where your extender operates In the Security Options field select the type of wireless security that you want to use on your network None This is an open wireless network Any wireless computer or device is allowed to join this network WEP WEP is an older standard and is less secure than WPA or WPA2 WEP uses encryption keys and data encryption for data security You can select 64 bit or 128 bit encryption For more information see Set Up WEP on page 29 WPA PSK TKIP WPA is more secure than WEP When using wireless computers or devices that support WPA you can enter a passphrase to join the extender wireless network For more information see Set Up WPA WPA2 or WPA WPA2 on page 30 WPA2 P
26. g displays Wireless Card Access List Available Wireless Cards MAC Address Wireless Card Entry Device Name MAC Address Help Center Show Hide Help Center 4 Enter the device name and MAC address 5 Click the Add button The device is added to the list 6 On the Advanced Wireless Settings screen click the Apply button Your changes are saved Extender Network Settings 38 Troubleshooting This chapter covers the following topics e Smart Wizard FAQs e Connecting to http mywifiext net e Joining Wireless Networks 39 Universal Pass Through WiFi Range Extender WN3100RP Smart Wizard FAQs 1 When connect to the network Smart Wizard keeps asking me for my passphrase and am sure I ve entered the correct passphrase What can do It is very likely that the extender is placed at the borderline of the range covered by the router or gateway See Place the Extender and Power It On on page 14 got an error message in the Review Settings screen in the Smart Wizard What should do Make sure that your computer is connected to the extender by using the SSID and the passphrase that you have just set up and clicking the Refresh button in your browser This will return you to the Smart Wizard connected to NETGEAR_EXT and launched a browser but why can t see the Smart Wizard a Make sure that your computer is set up to use DHCP If you set up your computer to use a Static IP addre
27. ge Extender WN3100RP e Use Static IP Address Specify a static IP address This is not usually necessary If you set this up you should be technically experienced or have a technically experienced person help you IP Address The static IP address IP Subnet Mask The subnet mask associated with the IP address Gateway IP Address The IP address for the gateway Primary DNS The primary domain name server DNS Secondary DNS The secondary domain name server DNS Status Screen When you connect to http mywifiext net and after the extender does the automatic firmware check the Status screen displays You can also view the Status screen at any time gt To view the Status screen 1 Select Maintenance gt Status A screen similar to the following displays NETGEAR genie es Firmware Version WN3100RP V1 0 0 6_ 1 0 12 Hardware Version Setup Wizard Add WPS Client gt Setup v Maintenance Attached Devices Backup Settings Set Password Firmware Update Firmware Version GUI Language Version Connection Status to Existing Network Name SSID Link Rate Connection Status Extender IP Info MAC Address WN3100RP a V1 0 0 6_1 0 12 V1 0 0 6_2 1 9 5 2NTGR125 300 Mbps Connected 00 FF FF FF FF FF IP Address 192 168 0 10 DHCP Client ON IP Subnet Mask 255 255 255 0 Gateway IP Address 192 168 0 1 Domain Name Server 192 168 0 1 gt Advanced Extender Wireless Setting Name SSID
28. he extender gt To log in to the extender and use WPS to connect 1 Select Add WPS Client Extender Network Settings 25 Universal Pass Through WiFi Range Extender WN3100RP The following screen displays Ada WPS Client Add WPS Client gt Setup New and easy way to connect to the Wireless Access Point Extender via WiFi Protected setup WPS gt Maintenance Awireless client has to support WPS function in order to use this wizard to add the client to your WPS enabled Wireless Access Point Please check the user manual and giftbox of your wireless client to see whether it supports the WPS function If your wireless client does not support the WPS function you have to configure your wireless client manually so it has the same SSID and wireless security settings as on this Wireless Extender gt Advanced Help Center Show Hide Help Center 2 Click the Next button 3 Select a radio button e Push Button recommended Either click the button or press the WPS a button on the side of the extender Add WPS Client Select a setup method Push Button recommended You can either press the Push Button physically on the Wireless Extender or press the Button below soft Push Button PIN Number Help Center Show Hide Help Center Extender Network Settings 26 Universal Pass Through WiFi Range Extender WN3100RP e PIN Number Select the PIN number radio button and enter the
29. i Range Extender WN3100RP gt To connect the extender with WiFi 1 Plug the extender into an electrical outlet 2 Launch an Internet browser on your laptop tablet or smartphone 3 Type http mywifiext net and log in to the extender see Connect the Extender to an Existing Network on page 24 4 Select the Setup Wizard on the extender menu 5 Follow the wizard steps to connect the extender to the local WiFi network but leave its network name and security settings the same Because your wireless devices have connected to the extender network before you can easily connect to that network again 6 Use your wireless devices to find and join the extender network 7 Launch a browser and access the Internet Getting Started 21 Universal Pass Through WiFi Range Extender WN3100RP Restore Factory Settings You can use the extender Factory Reset button to restore the factory settings gt To restore the factory settings 1 Insert a paper clip into the Factory Reset hole and hold it until the Power LED blinks amber _ a 2 Release the button All LEDs turn off for about 3 seconds The Power LED lights solid amber for about 30 seconds The Power LED W lights solid green Getting Started 22 Extender Network Settings To change settings connect the extender to your computer and use your Internet browser to go to http mywifiext net as described in Extender Port Connection on page 12 Conne
30. l digits any combination of 0 9 a f or A F 5 Enter the encryption keys You can manually or automatically program the four data encryption keys These values must be identical on all computers and access points in your network e Passphrase To use a passphrase to generate the keys enter a passphrase and click the Generate button This automatically creates the keys Wireless computers must use the passphrase or keys to access the extender Note Not all wireless computers support passphrase key generation If your computer does not support the passphrase then you have to type the encryption key to join the wireless network e Key 1 Key 4 Manually enter the four data encryption keys These values are not case sensitive These values must be identical on all computers and access points in your network Enter 10 hexadecimal digits any combination of 0 9 a f or A F 6 Select which of the four keys is the default Data transmissions are always encrypted using the default key The other keys can be used only to decrypt received data The four entries are disabled if WPA PSK or WPA authentication is selected 7 Click the Apply button Your settings are saved Extender Network Settings 29 Universal Pass Through WiFi Range Extender WN3100RP Set Up WPA WPA2 or WPA WPA2 Both WPA and WPA2 provide strong data security WPA with TKIP can be used on Windows systems with Service Pack 2 or later WPA2 with AES is a hard
31. lar to the following displays Extender to Router Device to Extender Apply Settings You are now one step away from completing the installation Your Extender network has been created 2NTGR125_EXT Next you will need to connect your wireless devices to the Extender network On your wireless device e g laptop tablet smartphone gaming console etc use the wireless manager to find the extender network names and connect For example you might use Windows software as shown below to connect your PC to the Extender network Choose a wireless network Network Tasks g Refresh network ist Cick an item in the list below to conmact to a wireless network in range or to gat more riformetion a lt 2 Set up a wareless network o NTGR_jtv _EXT for a home or small office E Securty enabled wireless network WPA2 vail Wireless network name SSID 2NTGR125_EXT Security type WPA2 PSK Passphrase YourPasswordHere E My wireless devices are connected to the Extender network Selecting this checkbox activates the Continue button 7 To use the same password to access the extender s wireless network that you use for wireless access to your existing network click the copy password button Connect your wireless device to the extender s wireless network 8 Use the wireless manager of your wireless device to find the wireless network name SSID of the extender s network The extender s wireless network name
32. n Internet browser such as Mozilla Firefox or Microsoft Internet Explorer In the address field of your browser enter http mywifiext net You are prompted to enter a user name and password Authentication Required i A username and password are being requested by http jeva mywifiext net UserName Password If you do not see the login prompt make sure to include http when you type http mywifiext net in your browser Type admin for the user name The default password is password NETGEAR recommends that you set a more secure password after you log in see Set the Password on page 35 e If your extender has an Internet connection the Firmware Update screen displays see Update the Firmware on page 36 and the software automatically checks for new firmware at the NETGEAR website Getting Started 17 Universal Pass Through WiFi Range Extender WN3100RP e The Status screen displays with the menu on the left This screen shows what the current settings are for the extender Menu Status screen Logout NETGEAR Firmware Version WN3100RP V1 0 0 6_1 0 12 Setup Wizard Status Add WPS Client Hardware Version WN3100RP Firmware Version V1 0 0 6_ 1 0 12 Setup GUI Language Version V1 0 0 6_2 1 9 5 Neri Connection Status to Existing Network Name SSID 2NTGR125 Link Rate 300 Mbps Attached Devi Attached Dewces Connection Status Connected Backup Settings Set Password Extender IP Info Firmware Update MAC
33. o far away from the router or wireless client ES Blinking Left Arrow The extender is too far away from the router or om lt 3 gateway ey AT Blinking Right Arrow The extender is too far away from your computer or wireless client 5 Use the LED colors to monitor and adjust your connection For more information see Monitor Extender Performance on page 17 Note If you are having trouble getting a good WiFi signal try to create a better line of sight For example move the router or gateway up off the floor onto a table or desk or move furniture that might be blocking the extender Getting Started 16 Universal Pass Through WiFi Range Extender WN3100RP Monitor Extender Performance The Router Link LED indicates performance between the router or gateway and the extender If this LED Is off the extender is not connected to a WiFi network HD The Client Link LED indicates the performance between the extender and the client If this LED is off no computer or wireless device is connected to the extender network These LEDs display the following colors Green indicates the best performance __ Amber indicates a workable performance Red indicates a poor connection or no connection Log In to the Extender You can log in to the extender to use the Smart Wizard or to use the menu selections to view or change the extender s settings gt To log in to the extender 1 2 On your computer launch a
34. o the following displays Setup Wizard Attached Devices Add WPS Client gt Setup v Maintenance Wired Devices Statu IP Address Device Name MAC Address Virtual MAC Address atus 1 192 168 0 11 USER HP 60 EB 69 76 2F 1D 02 0F B5 76 2F 1D Attached Devices Backup Settings Wireless Devices Wireless intruders also show up here Set Password OO O IP Address Device Name MAC Address Virtual MAC Address Firmware Update aa gt Advanced Help Center p Show Hide Help Center Extender Network Settings 33 Universal Pass Through WiFi Range Extender WN3100RP Back Up and Manage Extender Settings The Backup and Restore options in the Backup Settings screen let you save and retrieve a file containing your extender s configuration settings Once you have your extender working correctly back up the information to have it available if something goes wrong When you back up the settings they are saved as a file on your computer You can restore the device s settings from this file gt To manage extender settings 1 Select Maintenance gt Backup Settings The following screen displays Setup Wizard Backup Settings Add WPS Client Ll a hob LLL LLL ee Save a Copy of Current Settings gt Setup v Maintenance Restore Saved Setting from a File Status Attached Devices Backup Settings Set Password Firmware Update Revert to Factory Default Settings gt Advanced Help Center Show
35. of sight between the extender and the router or gateway you are connecting to Make sure that there are no physical obstacles between the extender and the router or gateway and try to move the extender closer to the router or gateway If you use the Smart Wizard and the extender cannot connect to the router or gateway or cannot get an IP address from the router or gateway it displays the following message You are not able to connect to the Internet Click Continue to run through set up again to connect to your network If you click the Continue button the Smart Wizard starts again see Use the Smart Wizard to Change the Settings on page 18 If you click the Exit button the Status screen displays with menu selections on the left see Log In to the Extender on page 17 Troubleshooting 41 Supplemental Information This appendix covers the following topics e Factory Settings e Technical Specifications e Safety Information 42 Universal Pass Through WiFi Range Extender WN3100RP Factory Settings You can press and hold the Factory Settings button on the side panel for seven seconds The extender resets and returns to its factory settings 1 Maximum wireless signal rate IEEE Standard 802 11 Actual throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Technical Specification
36. rk e Extender Wireless Settings Name SSID The name SSID of the wireless network Region The country where the extender is set up for use Channel The current channel which determines the operating frequency Wireless mode The maximum data rate of the wireless connection Wireless AP Indicates if the access point AP feature is enabled Broadcast Name Indicates if the extender is configured to broadcast its SSID Wi Fi Protected Setup Indicates whether Wi Fi Protected Setup is configured gt To view the statistics of your connections On the Status screen click the Show Statistics button A screen similar to the following displays NETGEAR WN3100RP Mozilla Firefox Show Statistics System Up Time 01 35 22 Port Status TxPkts RxPkts pena Tx Bis Rx Bis Up Time LAN pamana 16436 4616 2189 00 16 06 227 waan 3 12361 15739 00 09 30 Poll Interval 5 Extender Network Settings 32 Universal Pass Through WiFi Range Extender WN3100RP Table 1 Show statistics fields Colision Rx B s Up Time Poll Interval Specify the poll interval frequency If you change this value click the Set Interval button so that your change takes effect Attached Devices Use the Attached Devices screen to find out the devices that are connected to the extender gt To view the devices that are attached to your extender Select Maintenance gt Network Devices A screen similar t
37. rkable performance e Red indicates a poor connection or no connection If you cannot get a wireless connection working you can use an Ethernet cable to connect your computer to the extender See Extender Port Connection on page 12 Joining Wireless Networks To join a wireless network you must know its network name also called the SSID so that you can select it If the network is secure you must know the passphrase or wireless key If the extender does not connect to the network that you chose the following message displays Connection was not established to the selected network lf this happens it could be for one of these reasons e The network name passphrase or key might have been typed incorrectly Click the Cancel button use the Smart Wizard to select the network from the list and retype the passphrase or key This is case sensitive PASSWORD25 is not the same as Password25 or password25 See Use the Smart Wizard to Change the Settings on page 18 e If the Smart Wizard does not find your wireless network it is not displayed in the Select the name of your existing network screen check to see that the wireless network is still working properly Make sure that the router or gateway is turned on If possible move the extender closer to the router or gateway and click the Try Again button e If the Router Link LED is red this indicates a poor wireless connection The best connection is established when there is a clear line
38. s Technical Specifications Network protocol and Data and Routing Protocols TCP IP DHCP server and client standards compatibility AC input 100 240V 0 3A max Physical specifications e Dimensions 114 x 55 x 32 5 mm e Weight 175 g Environmental e Operating temperature 32 to 140 F 0 to 40 C e Operating humidity 90 maximum relative humidity noncondensing e Electromagnetic emissions Meets requirements of EMC Directive 2004 108 EC Interface e Local 10BASE T 100BASE Tx RJ 45 e 802 11n g b Supplemental Information 43 Universal Pass Through WiFi Range Extender WN3100RP Safety Information Follow these safety guidelines to ensure your own personal safety and to help protect your system from potential damage For national approvals approval schemes other than CB relevant national standards for plug socket outlet and direct plug in units for example US shall also be consulted while you are testing and approving such products according to the national standards Check the electrical current for any device plugged into the filtered AC socket Do not exceed home and product outlet ratings and electrical requirements The socket outlet shall be installed near the equipment and be easily accessible Only power cords are allowed to be inserted into the filtered AC socket no other equipment with a direct plug in is allowed Power cords needs to be a maximum of 1 m long and have a minimum of 0 75 mm2 of
39. s that you set a more secure password gt To set your password 1 Select Maintenance gt Set Password The following screen displays gt Setup v Maintenance Old Password Set Password Status Attached Devices Repeat New Password Backup Settings F Backup Settings Enable Password Recovery Set Password Firmware Update gt Advanced Show Hide Help Center Help Center 2 Type the old password and then type the new password twice 3 To enable password recovery select the Enable Password Recovery check box Extender Network Settings 35 Universal Pass Through WiFi Range Extender WN3100RP A new Set Password screen displays Set Password Old Password Set Password Repeat New Password v Enable Password Recovery Security Question 1 Select a question Answer Security Question 2 Select a question Answer required information Last time password was recovered Help Center Show Hide Help Center 4 Select the two questions and enter the answers 5 Click the Apply button Update the Firmware The extender checks for new firmware automatically at login gt To check for firmware and upgrade if it is available 1 Select Maintenance gt Firmware Update The following screen displays Setup Wizard Firmware Update Add WPS Client Check for new version online gt Setup Locate and select the upgrade file from your hard disk Status Attach
40. se a power cable that is approved for use in your country The power cable must be rated for the product and for the voltage and current marked on the product s electrical ratings label 46 Universal Pass Through WiFi Range Extender WN3100RP The voltage and current rating of the cable should be greater than the ratings marked on the product e To help prevent electric shock plug the system and peripheral power cables into properly grounded electrical outlets e Do not use adapter plugs If you must use an extension cable use a three wire cable with properly grounded plugs e Observe extension cable and power strip ratings Make sure that the total ampere rating of all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip e To help protect your system from sudden transient increases and decreases in electrical power use a Surge suppressor line conditioner or uninterruptible power supply UPS e Position system cables and power cables carefully route cables so that they cannot be stepped on or tripped over Be sure that nothing rests on any cables e Do not modify power cables or plugs e Always follow your local and national wiring rules Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices
41. ss you have to change the settings back so that it uses Dynamic Host Configuration Protocol DHCP b Make sure that the Client Link LED is green Move the extender closer to your computer if necessary For more information see Find the Best Location on page 7 c Relaunch the browser and enter http mywifiext net d Check to make sure that your computer has an IP address in the IP Address Setup screen see Extender IP Address Setup on page 30 Connecting to http mywifiext net If you have trouble connecting try to locate the source of the problem For help with passwords see Log In to the Extender on page 17 If your browser displays an error page make sure that you include http when you type this URL in the address field of your Internet browser If you leave it out you might not be able to connect The extender LEDs can help you tell if the extender is correctly set up and working as it should Ku The Router Link LED indicates performance between the router or gateway and the extender If this LED is off the extender is not connected to a WiFi network E The Client Link LED indicates the performance between the extender and the client If this LED is off no computer or wireless device is connected to the extender network These LEDs display the following colors Green indicates the best performance Troubleshooting 40 Universal Pass Through WiFi Range Extender WN3100RP e Amber indicates a wo
42. ware implementation see your device documentation before implementing it gt To set up WPA or WPA2 in the extender 1 Select Setup gt Wireless Settings 2 Inthe Security Options section select the radio button for the WPA or WPA2 option of your choice 3 The settings displayed on the screen depend on which security option you select For WPA PSK or WPA2 PSK enter the passphrase 5 Click the Apply button Your settings are saved Extender IP Address Setup The IP Address Setup screen shows whether the extender is set to get its IP address dynamically from the router or gateway this is the most common seiting or is set witha Static IP address gt To view or change the extender IP address setup 1 Select Maintenance gt IP Address The following screen displays Setup Wizard IP Address Setup v Setup Connect to Existing Network Get Dynamically IP Address From Router Wireless Settings Use Static IP Address IP Address Setup IP Address gt Maintenance IP Subnet Mask gt Advanced Gateway IP Address Primary DNS Help Center Show Hide Help Center 2 View or configure the following settings e Get Dynamically IP Address From Router The wireless network router or gateway assigns an IP address when the extender connects to Its wireless network Most networks are set up so that the router or gateway automatically does this Extender Network Settings 30 Universal Pass Through WiFi Ran
43. will keep blinking slowly Iv Keep Existing Wireless Settings Wireless Card Access List Help Center m lt Show Hide Help Center 2 View or configure the following settings Enable Wireless Access Point Select this check box to enable the extender to work as a wireless access point If this check box is cleared then computers or wireless devices cannot connect wirelessly to the extender Enable SSID Broadcast Select this check box to enable the extender to broadcast its wireless network name SSID If this check box is cleared then the wireless network is hidden To join a hidden wireless network type the wireless name Disable Device s PIN Select this check box to disable the extender s PIN The PIN can be used for a WPS wireless connection Keep Existing Wireless Settings Select this check box to keep the settings in the Wireless Settings screen unchanged when a wireless connection is made with WPS Setup Access List Specify a list of computers or wireless devices that are allowed to connect to the network Extender Network Settings 37 Universal Pass Through WiFi Range Extender WN3100RP If you use an access list then computers that are not on the list are not allowed to join the wireless network The computers that are allowed to join are identified by their MAC addresses gt To add a device to the wireless card access list 3 Click the Setup Access List button A screen similar to the followin
44. y when the computer is in a dead zone where connection from the network is very poor or nonexistent Find the Best Location Extender WiFi router Client Figure 2 Best location When you install the extender and join the extender network the arrow LEDs guide you to the best location to plug in the extender If no arrow is lit the location is good Y lt a Blinking Left Arrow The extender is too far away from the router or gateway e AT Blinking Right Arrow The extender is too far away from your computer or wireless client The best connection is established when there is a clear line of sight between the extender and the wireless router or gateway and also a clear line of sight between the extender and the computer you are using If this straight path is blocked by a thick wall or other materials Getting Started 7 Universal Pass Through WiFi Range Extender WN3100RP move the extender to a different location half way between the computer and the router or gateway Use the Pass Through Power Socket The extender provides a pass through power socket After you have the extender positioned correctly you can plug in the equipment that was previously plugged in the wall socket before you plugged in your extender Figure 3 Pass through power socket use The pass through power socket can carry up to 16A and 250 VAC Getting Started 8 Universal Pass Through WiFi Range Extender WN3100RP H
45. your computer to the extender with an Ethernet cable 2 Plug the extender into an electrical outlet AN CAUTION Do not use Ethernet cable to connect the extender to a router or gateway If you do so the extender does not work because it is designed to use only a wireless connection to the router or gateway 3 Log in to the extender For more information see Log In to the Extender on page 17 If you have trouble connecting e If you start your computer connect the Ethernet cable to the extender and launch your browser quickly the computer might still need a couple of minutes to recognize the Ethernet LAN connection before you can connect Getting Started 13 Universal Pass Through WiFi Range Extender WN3100RP Make sure that your Ethernet cable is securely connected to the extender and to the computer If the cable is not securely connected reconnect the Ethernet cable and relaunch your Internet browser Install the Extender Place the extender apply power and connect it to your WiFi network Place the Extender and Power It On Place the extender halfway between your router or gateway and the location that has poor WiFi coverage 1 l If it is not possible to place the extender at the halfway point move the extender closer to the location with poor coverage but still within the wireless range of the router or gt Se gateway 2 Turn the On Off switch on the side of the extender to the On position

Netgear WN3100RP User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents