Netgear RM356 User's Manual
Contents
1. NETGEAR MODEL RM 3 5 6 Voce Router Installation Guide A gt Start Here D Product Illustrations Congratulations on your purchase of a NETGEAR Model RM356 Modem Router These instructions show you how to configure your Windows PC network and your NETGEAR router for basic Internet access through an Internet service provider ISP For more detailed information about installing your router or configuring advanced features refer to Reference Guide for the Model RM 356 Modem Router Front Panel of the Router The front panel of the Model RM356 router contains status LEDs Refer to the illustration and table below for descriptions of the LEDs on the front panel of the router LAN LEDs MODEM LEDs NETGEAR WODERM356 56 kops remences Modem Router PWR TEST coL PP Bay Networks Test LED Power LED Front Panel of the Model RM356 Modem Router 8604FA Label Activity Description PWR Power On Power is supplied to the router TEST Blinking Off The router is functioning properly This LED blinks during initialization and then turns off LAN COL Collision Blinking Data collision is occurring on the LAN 1 4 On The numbered LAN port is synchronized with an attached device Blinking Data is being received on the LAN port MODEM OH Off Hook On The modem is in use CD On A valid carrier is present on the line Carrier Detect TX Transmit Blinking Data is being transmitted on the MODEM port RX Rece2. Microsoft Networks If you need the adapter a Click on the Add button b Select Adapter and then click on Add again c Select the manufacturer and model of your Ethernet adapter and click on OK If you need TCP IP a Click on the Add button b Select Protocol and then click on Add again c Select Microsoft d Select TCP IP and click on OK If you need Client for Microsoft Networks a Click on the Add button b Select Client and then click on Add again c Select Microsoft d Select Client for Microsoft Networks and click on OK Refer to your Windows 95 manual for further instructions Configuring TCP IP Properties At this point your PC is configured to obtain its TCP IP configuration information automatically from a DHCP server on the local network The Model RM356 router is shipped preconfigured as a DHCP server and will assign the TCP IP configuration information described in the previous section Configuring TCP IP Properties by DHCP If you will be using the configuration recommended by NETGEAR 1 Turn on the router Be sure the router has been on for at least one minute before continuing to step 2 2 Reboot your PC For additional configuration information such as DNS addresses you can either add the information to the DHCP setup of the router and reboot the PC again or enter the information manual
3. into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Part 68 Compliance Statement This equipment complies with Part 68 of FCC Rules All direct connections to telephone network lines must be made using standard plugs and jacks compliant with FCC Part 68 EN 55 022 Declaration of Conformance This is to certify that the Model RM356 Modem Router is shielded against the generation of radio interference in accordance with the application of Council Directive 89 336 EEC Article 4a Conformity is declared by the application of EN 55 022 Class B CISPR 22 Best tigung des Herstellers Importeurs Es wird hiermit best tigt da das Model RM356 Modem Router gem der im BMPT AmtsblVfg 243 1991 und Vfg 46 1992 aufgef hrten Bestimmungen entst rt ist Das vorschriftsmaBige Betreiben einiger Ger te z B Testsender kann jedoch gewissen Beschr nkungen unterliegen Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung Das Bundesamt fiir Zulassungen in der Telekommunikation wurde davon unterrichtet da dieses Ger t auf den Markt gebracht wurde und es ist berechtigt die Serie auf die Erf llung der Vorschriften hin zu berpr fen Model RM356 Modem Router Installation Guide NETGEAR NETGEAR Inc A Bay Networks Company 4401 Great America Parkway Santa Clara CA 95054 USA Phone 888 NETGEAR E Customer Support Phone Aus
4. will be assigned as follows 192 168 0 1 local IP address of your router and default gateway for the PCs 192 168 0 2 through 192 168 0 32 IP addresses of your PCs e 255 255 255 0 netmask for your router and PCs This information may be entered manually to each device or it may be assigned automatically by the default DHCP function of the router when the PCs are rebooted Connecting the Router Connect the router to a power source to your local area network LAN and to your telephone line as shown in Hardware Installation For your telephone line connection use the black cable provided For your LAN connection use the white straight through cable provided to connect your Model RM356 router either to a PC or to the Uplink port of an Ethernet hub Model RM356 Modem Router Installation Guide contiguring tcPiP Configuring Windows 95 for IP Networking All PCs must have an Ethernet network adapter card installed and must have the TCP IP networking protocol installed and configured as their networking protocol TCP IP installation must be done manually as described here To configure Microsoft Windows 95 for IP networking 1 Click on Start from the Windows tool bar located at the bottom of the screen 2 Select Settings 3 Select Control Panel 4 Select Network In the displayed list of installed components you must have an Ethernet adapter the TCP IP protocol and Client for
5. ach PC or workstation in your local network A LAN account is typically more expensive than a single user account Account Information Your ISP should give you the following basic information for your account whether it is a single user or LAN account e A local phone number for accessing the ISP e A login name e A password e IP address es unless dynamically assigned DNS server IP address es of the ISP Model RM356 Modem Router Installation Guide Network Checklist The Model RM356 Modem Router uses the Internet Protocol IP The IP configuration has the following requirements e AIl PCs must have TCP IP manually installed and manually selected as the networking pro tocol See Configuring TCP IP for further instructions e All PCs and the router must be assigned IP addresses If your ISP or network administrator has not assigned these use private addresses as described below If you are using the default Dynamic Host Configuration Protocol DHCP function of the router these private addresses are assigned automatically by the router when the PCs are rebooted e All PCs must have the IP address of the router defined as the default gateway If you are using the default DHCP function of the router this IP address is assigned automatically by the router when the PCs are rebooted Using Private Internet Protocol IP Addresses If you will be using the private addressing scheme recommended by NETGEAR your IP addresses
6. e corresponding port LED on the router should be on If the connection test fails after the Quick Configuration look in the displayed trace for details Recheck your ISP account phone number login name and password If the router does not place a call when you launch your browser your PC might not have the router configured as its TCP IP gateway If the PC gets its information from the router by DHCP reboot the PC and verify the gateway address as described in Verifying TCP IP Properties If the router connects but you cannot load pages from the Internet the PC might not know any DNS server addresses A DNS server is a host on the Internet that translates Internet names such as www addresses to numeric IP addresses Typically your ISP will provide the addresses of one or two DNS servers for your use If you entered a DNS address during the Quick Configuration reboot your PC and verify the DNS address as described in Verifying TCP IP Properties You can also configure your PC manually with DNS addresses as explained in Configuring TCP IP More detailed information can be found in the Troubleshooting sections of Reference Guide for the Model RM356 Modem Router and Getting Started Using FirstGear for the Model RM356 Modem Router Model RM356 Modem Router Installation Guide 1998 by NETGEAR Inc All rights reserved Trademarks Bay Networks is a registered trademark of Bay Networks Inc NETGEAR and FirstGear are t
7. e information about installing your router refer to Reference Guide for the Model RM356 Modem Router and Getting Started Using FirstGear for the Model RM356 Modem Router Model RM356 Modem Router Installation Guide Accessing the Internet When your router and PCs are configured correctly your router places a call automatically whenever an application requires access to the Internet The router also disconnects from the Internet when the connection has been idle for a period of time It is not necessary for you to run a dialer application such as Dial Up Networking to connect log in or disconnect These functions are performed by the router as needed To access the Internet launch a browser application such as Microsoft Internet Explorer or Netscape Navigator On the router you should see the Offhook OH LED illuminate followed shortly by the Carrier Detect CD LED Soon the data transmit and receive LEDs TD and RD will begin to flicker indicating communication between your router and your ISP The browser should then begin to display a page This process may take up to one minute After about five minutes of inactivity the router will disconnect the call Upon further browser activity the router will redial automatically B Common Problems Here are a few common problems and likely causes e If FirstGear cannot find your router check the Ethernet connection between your PC and router The link LED on your Ethernet card and th
8. ive Blinking Data is being received on the MODEM port Model RM356 Modem Router Installation Guide Rear Panel Refer to this diagram to identify all of the ports on the router when you attempt to make any connections The Model RM356 router has four UTP LAN ports for connecting to PCs or hubs and a Manager port for connecting to a management terminal optional The line port connects to your phone jack and the phone port allows a phone or fax machine to share the phone line with the router AC adapter outlet Line port MANAGER LINE PHONE Lala UTP LAN RJ 45 Phone ports Manager port port Rear Panel of the Model RM356 Modem Router 8605FA Hardware Installation Refer to the following illustration for installing and connecting your Model RM356 Modem Router Configuration by FirstGear is performed from a PC attached to a LAN port The network manager terminal is only necessary for installing software upgrades PHONE1 AC power adapter i a Network Phone or other PCs manager analog devices or hubs optional Installing the Model RM356 Modem Router 8623FA Model RM356 Modem Router Installation Guide E Setup and Preparation Telephone Line Checklist The Model RM356 Modem Router connects to the Public Switched Telephone Network PSTN using a standard analog voice line When ordering telephone service the following information should be verified e Line Quality Though the m
9. ly to the PC as described in the following section Model RM356 Modem Router Installation Guide Configuring TCP IP Properties Manually If you choose not to configure your PC by DHCP you must manually enter the following information in the TCP IP Properties section of the Network Control Panel of your PC e IP address and subnet mask choose from your assigned IP addresses or private IP addresses Gateway enter the IP address of the router e DNSserver addresses enter IP addresses provided by your ISP Verifying TCP IP Properties After your PC has been configured and rebooted you can check the TCP IP configuration using the Windows utility winipcfg exe for Windows NT systems use ipconfig exe From the Start button open the Run window type winipcfg and click on OK Note In addition to displaying the current TCP IP properties the winipcfg utility allows you to release and renew DHCP assigned information without rebooting the PC Model RM356 Modem Router Installation Guide Running FirstGear To run the FirstGear configuration software 1 Install the FirstGear software on any PC with an Ethernet connection to the router by inserting the diskette and running the Setup program a Click on Start from the Windows tool bar b Click on Run c Typea setup d Click on OK in the Run window e Follow the setup instructions Be sure the router has been on for at least one mi
10. nute before launching FirstGear Double click on the FirstGear icon that now appears on your desktop If you need to change the netmask or IP address of your router enter the new information and click on Apply If your password has been previously changed from the factory default of 1234 you will be prompted to enter the current password Click on Return in the Find Router screen Click on Quick to Run the Quick Configuration procedure Follow the instructions in each screen For detailed information about data to be entered in each screen click on the Help button at the bottom of the screen At the last screen send the configuration to the router by clicking on Send to Router Wait for the router to reboot Click on Test The router will place a call to your ISP and log in to your account If the test is not successful a trace will be displayed containing information that should help in troubleshooting Refer to the Troubleshooting sections in the Reference Guide for the Model RM356 Modem Router and Getting Started Using FirstGear for the Model RM356 Modem Router Click on Finish If you have made changes in the DHCP setup of your router you will be prompted to reboot your PC so that it can obtain the new DHCP information from the router Reboot any other PCs on the local network Your Model RM356 router is now fully configured to provide Internet access for your network For mor
11. odem is capable of 56 Kbps download performance the condition of your telephone line and your local public telephone infrastructure may limit your actual data rate For example FCC rules limit the data rate to 53 Kbps in the United States The use of repeaters between your premises and the central office will limit your performance to 33 Kbps If your data rate is substantially less than 50 Kbps you may want to consult your telephone company regarding the quality of your line Calling Line Identification CLID If you require CLID for security you must order CLID for your line from your local carrier ISP Checklist If you will be contracting with an Internet service provider ISP for Internet access you must choose between a single user account and a multiuser LAN account You can connect a multiuser network through a single user account by using the Network Address Translator NAT feature of your router Single User Account In a single user account you are assigned only one registered Internet Protocol IP address This address may be a permanent fixed address or it may be a different address assigned dynamically each time you log in to the account The NAT feature of your router will map the IP addresses of your network to this address for accessing the Internet Some applications may be incompatible with NAT LAN Account In a LAN account you will be assigned a registered IP address for your router and one for e
12. rademarks of Bay Networks Inc Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation All other trademarks and registered trademarks are the property of their respective owners Statement of Conditions In the interest of improving internal design operational function and or reliability NETGEAR reserves the right to make changes to the products described in this document without notice NETGEAR does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Certificate of the Manufacturer Importer It is hereby certified that the Model RM356 Modem Router has been suppressed in accordance with the conditions set out in the BMPT Amtsbl Vfg 243 1991 and Vfg 46 1992 The operation of some equipment for example test transmitters in accordance with the regulations may however be subject to certain restrictions Please refer to the notes in the operating instructions Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations VCCI 2 Statement This equipment is in the 2nd Class category information equipment to be used in a residential area or an adjacent area thereto and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machine
13. s aimed at preventing radio interference in such residential areas When used near a radio or TV receiver it may become the cause of radio interference Read instructions for correct handling Federal Communications Commission FCC Compliance Notice Radio Frequency Notice This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment
14. tralia 1800 142 046 France 0800 90 2078 Japan 0120 66 5402 Korea 00308 11 0319 New Zealand 0800 444 626 Sweden 020 790086 United Kingdom 44 171 571 5120 U S Canada 800 211 2069 Internet World Wide Web The NETGEAR Web page is at http NETGEAR baynetworks com Defective or damaged merchandise can be returned to your point of sale rep resentative M 2 i R M 3 3 6 N A st 0
Download Pdf Manuals
Related Search