Netgear GS110TP User's Manual
Contents
1. Step 5 Applying AC Power Before connecting the power cord select an AC outlet that is not controlled by a wall switch which can turn off power to the switch After selecting an appropriate outlet use the following procedure to apply AC power 1 Connect the end of the supplied IEC AC power adapter cable to the power receptacle on the back of the switch 2 Connect the AC power adapter cable into a power source such as a wall socket or power strip When applying power the Power LED on the switch s front panel illuminates If the Power LED does not go on check that the power cable is plugged in correctly and that the power source is good If this does not resolve the problem refer to Appendix A Step 6 Managing the Switch using a Web Browser or the PC Utility The GS110TP Smart PoE Switch contains software for viewing changing and monitoring the way it works This management software is not required for the switch to work The ports can be used without using the management software However the management software enables the setup of VLAN and Trunking features and also improves the efficiency of the switch which results in the improvement of its overall performance as well as the performance of the network After powering up the switch for the first time the Smart Switch can be configured using a Web browser or a program called Smart Control Center Utility For more information about managing the switch see the Gigabit Adv2. GS110TP Haraware Installation Guide Table 4 1 Site Requirements continued Power source Provide a power adapter included Power specifications for the switch are shown in Appendix A Ensure the AC outlet is not controlled by a wall switch which can accidentally turn off power to the outlet and the switch Environmental Temperature Install the switch in a dry area with ambient temperature between 0 and 50 C 32 and 122 F Keep the switch away from heat sources such as direct sunlight warm air exhausts hot air vents and heaters e Operating humidity The installation location should have a maximum relative humidity of 90 non condensing e Ventilation Do not restrict airflow by covering or obstructing air inlets on the sides of the switch Keep at least 2 inches 5 08 centimeters free on all sides for cooling Be sure there is adequate airflow in the room or wiring closet where the switch is installed Operating conditions Keep the switch at least 6 ft 1 83 m away from nearest source of electromagnetic noise such as a photocopy machine Step 2 Installing the Switch The GS110TP Smart PoE Switch can be used on a flat surface or mounted on the wall Installing the Switch on a Flat Surface The switch ships with four self adhesive rubber footpads Stick one rubber footpad on each of the four concave spaces on the bottom of the switch The rubber footpads cushion the switch against shock vibrations Wall
3. CISPR 22 55024 and 50082 1 VCCI Class B C Tick Safety UL cUL UL 1950 cUL IEC950 EN60950 CE includes EN60950 IEC950 CB Technical Specifications B 3 v1 0 March 2010 GS110TP Haraware Installation Guide B 4 v1 0 March 2010 Technical Specifications Numerics 1U 1 3 8 pin 2 3 A Applying AC Power 4 4 Auto Uplink 2 4 Auto negotiating 2 Autosensing 1 2 2 3 Backpressure 7 2 C Category 5 Unshielded Twisted Pair 2 Checking the Installation 4 3 Class of Service Connecting Devices to the Switch 4 3 Copper 1 1 Crossover 2 4 D Default IP Address 4 5 Default Reset Button 2 Desktop Switching 3 Device Hardware Interfaces 2 2 Duplex Mode 2 3 E Example of Desktop Switching 3 Index F Factory Default Button 2 4 Factory Defaults 2 Flat Surface 4 2 Full duplex 2 G Gigabit Ports H High speed Servers IEEE 802 31 2 IEEE 802 3x 1 2 IEEE Standards 2 IEEE compliant 2 Installation Guide 4 Installing the Switch 4 2 L LED Designations 2 2 Low Latency 1 2 MAC 1 2 Media Access Control 2 N Netgear Smart Control Center Utility Index 1 v1 0 March 2010 GS110TP Haraware Installation Guide O Operating Conditions 4 2 Operating Environment 4 Operating humidity 4 2 Overview P Package Contents 1 4 Pause Frame Flow Control 7 2 Port LEDs 2 2 Power cord 1 4 Preparing the Site 4 R Rack mount Kit 1
4. 802 1D Spanning Tree Protocol IEEE 802 1 w Rapid Spanning Tree Protocol IEEE 802 1X Port Security IEEE 802 3AB LLDP SNMP vI v2c and v3 HTTP and HTTPS Port Mirroring RX TX and Both IGMP Snooping v1 v2 IEEE 802 1p Class of Service CoS SNTP Simple Network Time Protocol 2 servers Disabled by default Jumbo Frame Support Technical Specifications B 1 v1 0 March 2010 GS110TP Haraware Installation Guide Interface Eight RJ 45 connectors for 10BASE T 100BASE TX and 1000BASE T Auto Uplink on all ports Two SFP slots for SFP modules LEDs Per RJ 45 port Speed Link Activity Per SFP port SFP indicator Performance Specifications Forwarding modes Store and forward Bandwidth 20 Gbps Address database size 4K media access control MAC addresses per system Mean Time Between Failure MTBF 157 004 hours Power Supply 48V 1 25A 60W external power adapter Physical Specifications Dimensions H x W x D 236 x 101 6 x 27 mm 9 3 x 4 x 1 07 in Weight 0 7 1 55 kg Ibs Environmental Specifications Operating temperature 0 C to 50 C 32 to 122 F Operating humidity 10 to 90 maximum relative humidity noncondensing Storage temperature 20 C to 70 C 4 to 158 F Storage humidity 5 to 95 maximum relative humidity noncondensing B 2 Technical Specifications v1 0 March 2010 GS110TP Hardware Installation Guide Electromagnetic Emissions FCC Class B CE Class B Includes EN55022
5. Mounting the Switch To mount the switch on a wall optional install the two provided screws in positions that correspond to the slots on the bottom side of the GS110TP then mount the switch 4 2 Installation v1 0 March 2010 GS110TP Hardware Installation Guide Step 3 Checking the Installation Before applying power to the switch perform the following e Inspect the equipment thoroughly e Verify that all cables are installed correctly e Check cable routing to make sure cables are not damaged or creating a safety hazard e Ensure all equipment is mounted properly and securely Step 4 Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch s RJ 45 ports The GS110TP Smart PoE Switch contains Auto Uplink technology which allows the attaching of devices using either straight through or crossover cables Desktop PC Desktop PC Figure 4 1 Installation 4 3 v1 0 March 2010 GS110TP Haraware Installation Guide Connect each PC to an RJ 45 network port on the Switch front panel Figure 4 1 Use Category 5 Cat5 Unshielded Twisted Pair UTP cable terminated with an RJ 45 connector to make these connections mj Note Ethernet specifications limit the cable length between the switch and the attached device to 100 m 328 ft
6. Table 2 1 Port LEDs Speed Link Activity e Off No link is established on the port Left LED on each RJ 45 port Solid Green A valid 1000 Mbps link is established on the port e Flashing Green Packet transmission or reception is occurring on the port at 1000 Mbps e Solid Yellow A valid 10 100 Mbps link is established on the port e Flashing Yellow Packet transmission or reception is occurring on the port at 10 100 Mbps 2 2 Physical Description v1 0 March 2010 GS110TP Hardware Installation Guide Table 2 1 Port LEDs continued PoE Status e Off No PoE powered device PD connected Right LED on each RJ 45 port e Solid Green The PoE PD is connected and the port is supplying power successfully e Flashing Yellow One of the following failures resulted in stopping power to that port Short circuit on PoE power circuit PoE power demand exceeds power available PoE current exceeds PD s classification Out of proper voltage band 44 57 VDC SFP Port Indicate LED Off No link is established on the port e Solid Green A valid link is established on the port e Flashing Green Packet transmission or reception is occurring on the port System LEDs The following table describes the system LED designations Table 2 2 System LEDs Power Status LED Solid Green Power is supplied to the switch and the switch is operating normally e Solid Yellow The switch is booting Off P
7. a file server With full duplex enabled the switch port connected to the server or PC can provide 2000 Mbps throughput Internet Server N Q hu Firewall S Fe A Si SS SP S Desktop PCs Figure 3 1 3 1 v1 0 March 2010 GS110TP Haraware Installation Guide 3 2 v1 0 March 2010 Applications Chapter 4 Installation This chapter describes the installation procedures for your NETGEAR GS110TP Smart PoE Switch Switch installation involves the following steps Step 1 Preparing the Site Step 2 Installing the Switch Step 3 Checking the Installation Step 4 Connecting Devices to the Switch Step 5 Applying AC Power Step 6 Managing the Switch using a Web Browser or the PC Utility Step 1 Preparing the Site Before you install the switch ensure the operating environment meets the site requirements in the following table Table 4 1 Site Requirements Mounting e Desktop installations Provide a flat table or shelf surface Wall mount installations Wall mount select a location You also need the mounting screws supplied with your switch Access Locate the switch in a position that allows access to the front panel RJ 45 ports view the front panel LEDs and access the power connector 4 1 v1 0 March 2010
8. eliminating concern about whether to use crossover or straight through cables when attaching devices Reset Button The Smart Switch has a Reset button on the front panel to allow you to manually reboot the switch This action is equivalent to powering the unit off and back on The last saved configuration is loaded into the switch as it resets To operate the Reset button insert a device such as a paper clip into the opening to press the recessed button The front panel LEDs should extinguish and light again as the switch performs its Power On Self Test POST Factory Defaults Button The Smart Switch has a Factory Defaults button on the front panel so that you can remove the current configuration and return the device to its factory settings When you enable the Factory Defaults button all settings including the password VLAN settings and port configurations are removed To operate the Factory Defaults button insert a device such as a paper clip into the opening to press the recessed button for two seconds 2 4 Physical Description v1 0 March 2010 Chapter 3 Applications Your NETGEAR GS110TP Smart PoE Switch is designed to provide flexibility in configuring your network connections It can be used as a stand alone device or with 10 Mbps 100 Mbps and 1000 Mbps hubs and switches Desktop Switching The GS110TP Smart PoE Switch can be used as a desktop switch to build a small network that enables users to have 1000 Mbps access to
9. in a malfunction or damage to the equipment v1 0 March 2010 GS110TP Haraware Installation Guide Danger This is a safety warning Failure to take heed of this notice may result in personal injury or death e Scope This manual is written for the GS110TP Smart PoE Switch according to these specifications Product Version GS110TP Smart PoE Switch Manual Publication Date March 2010 Note Product updates are available on the NETGEAR Inc website at http kbserver netgear com products GS110TP asp How to Print this Manual To print this manual use the Complete PDF Manual link at the top left of any page Click the Complete PDF Manual link at the top left of any page in the manual The PDF version of the complete manual opens in a browser window Click the print icon in the upper left of the window Tip If your printer supports printing two pages on a single sheet of paper you can save paper and printer ink by selecting this feature Revision History Part Number verelen Date Description Number 202 10596 01 1 0 March 2010 Initial release vi About This Manual v1 0 March 2010 Chapter 1 Introduction Congratulations on the purchase of your NETGEAR GS110TP Smart PoE Switch The GS110TP Smart PoE Switch is a supplement to the Gigabit Advanced Smart Switch family Available as a desktop or wall mountable switch the GS110TP Smart PoE Switch is not intended to be rack mountable The GS
10. 110TP is a PoE supportable low port switch with two fiber uplinks included This chapter serves as an introduction to the GS110TP Smart PoE Switch and provides the following information e Overview e Features e Package Contents Overview This Installation Guide is for the NETGEAR GS110TP Smart PoE Switch This product offers support for eight 10 100 1000 Mbps autosensing and two 1000M SFP Gigabit Ethernet switching ports Using Gigabit ports high speed connections can be made to a server or network backbone For example e Linking to high speed servers e Providing 10 100 1000 Mbps copper connectivity The GS110TP Smart PoE Switch also provides the benefit of administrative management with a complete package of features for the observation configuration and control of the network With a Web based Graphical User Interface GUI the switch s many capabilities can be viewed and used in a simple and intuitive manner The switch s management features include configuration for port and switch information VLAN for traffic control port trunking for increased bandwidth and Class of Service CoS for traffic prioritization These features provide better understanding and control of the network Initial discovery of the switch on the network requires the Netgear Smart Control Center program a utility that runs on a PC v1 0 March 2010 GS110TP Haraware Installation Guide The GSIIOTP Smart PoE Switch is a free standing switch It is
11. 4 Reset Button 2 RJ 45 1 2 RJ 45 Ports 2 2 Rubber footpads 4 4 2 S Site Requirements 4 1 Smart Switch Resource CD 1 4 Straight through 2 4 System LEDs 2 3 T Temperature 4 2 Traffic Control 7 1 Troubleshooting Chart A 17 U User Intervention 2 4 User s Manual 4 UTP 4 4 Index 2 V Ventilation 4 2 VLAN W Web based Graphical User Interface 7 7 v1 0 March 2010
12. GS110TP Hardware Installation Guide NETGEAR NETGEAR Inc 350 East Plumeria Drive San Jose California 95134 USA 202 10596 01 March 2010 v1 0 2010 by NETGEAR Inc All rights reserved Trademarks NETGEAR the NETGEAR logo and Auto Uplink are trademarks or registered trademarks of NETGEAR Inc Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation Other brand and product names are registered trademarks or trademarks of their respective holders Portions of this document are copyright Intoto Inc Statement of Conditions In the interest of improving internal design operational function and or reliability NETGEAR reserves the right to make changes to the products described in this document without notice NETGEAR does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Certificate of the Manufacturer Importer It is hereby certified that the GS110TP Smart PoE Switch has been suppressed in accordance with the conditions set out in the BMPT AmtsblVfg 243 1991 and Vfg 46 1992 The operation of some equipment for example test transmitters in accordance with the regulations may however be subject to certain restrictions Please refer to the notes in the operating instructions The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the r
13. IEEE compliant and offers low latency for high speed networking All ports can automatically negotiate to the highest speed This capability makes the switch ideal for environments that have a mix of Ethernet Fast Ethernet or Gigabit Ethernet devices In addition all RJ 45 ports operate in half duplex or full duplex mode The maximum segment length is 328 feet 100 meters over Category 5 Unshielded Twisted Pair UTP cable Features The following list identifies the key features of the GS110TP Smart PoE Switch Eight RJ 45 10 100 1000 Mbps autosensing Gigabit Ethernet switching ports Two 1000M SFP Gigabit Ethernet switching ports Full NETGEAR Smart Switch functionality Full compatibility with IEEE standards e IEEE 802 3 CSMA CD e JEEE 802 31 LOBASE T e IEEE 802 3u 100BASE TX e IEEE 802 3x Full duplex flow control e IEEE 802 3ab LOOOBASE T e IEEE 802 3z 1000BASE x e IEEE 802 3af DTE power via MDI Autosensing and auto negotiating capabilities for all ports Auto Uplink on all ports to make the right connection Automatic address learning function to build the packet forwarding information table The table contains up to 4K Media Access Control MAC addresses Store and Forward transmission to remove bad packets from the network Full duplex IEEE 802 3x pause frame flow control Active flow control to minimize packet loss and frame drops Half duplex backpressure control Per port LEDs power LED Intro
14. anced Smart Switch Series Software Administration Manual on the Smart Switch Resource CD 4 4 Installation v1 0 March 2010 GS110TP Hardware Installation Guide Note When the device powers up there is a default IP address already configured on the device The default IP address is 192 168 0 239 and subnet mask 255 255 255 0 Installation 4 5 v1 0 March 2010 GS110TP Haraware Installation Guide 4 6 v1 0 March 2010 Installation Appendix A Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch Topics include the following e Troubleshooting Chart e Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms causes and solutions of possible problems Table A 1 Troubleshooting Chart Symptom Power LED is off No power is received Check the power cord connections the ON OFF switch and the connected device Ensure all cables used are correct and comply with Ethernet specifications Link LED is off or Port connection is not Check the crimp on the connectors and make sure intermittent working that the plug is properly inserted and locked into the port at both the switch and the connecting device Ensure all cables used are correct and comply with Ethernet specifications Check for a defective PC adapter card cable or port by testing them in an alternate environment where all products are functioning File transfer is
15. ck Panel Configuration e LED Designations e Device Hardware Interfaces GS110TP Front and Back Panel Configuration The GS110TP Smart PoE Switch has eight 10 100 1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports Each RJ 45 port is capable of sensing the line speed and negotiating the duplex mode with the link partner automatically Figure 2 1 illustrates the front panel of the NETGEAR GS110TP Smart PoE Switch Link Speed ACT LEDs left PoE Status LEDs right Power Status LED PoE Max LED Ld 10 100 1000 Mbps Ethernet Ports 1000M SFP Ports Figure 2 1 The front panel contains the following e Eight RJ 45 connectors for 10 100 1000 Mbps autosensing Gigabit Ethernet switching ports e Two 1000M SFP Gigabit Ethernet switching ports e Reset button to restart the device e Recessed default reset button to restore the device back to the factory defaults e Link Speed and Activity LEDs for each port 2 1 v1 0 March 2010 GS110TP Haraware Installation Guide e Power and Status LED e PoE Max LED Figure 2 2 illustrates the NETGEAR GS110TP Smart PoE Switch back panel f cin a a Power Connector Figure 2 2 The back panel contains the following e A DC input for the supplied 48V 1 25A external power adapter LED Designations Port LEDs The following table describes the RJ 45 and SFP port LED designations There are two LEDs for each RJ 45 port Each SFP port has its own indication LED
16. duction v1 0 March 2010 GS110TP Hardware Installation Guide e Standard NETGEAR Ixx series chassis e NETGEAR Green product features e External 48V 1 25A PA PoE Features The GS110TP Smart PoE Switch supports IEEE 802 3af PSE features e Ports 1 through 8 support IEEE 802 3af Alternative A MDI X e PoE is enabled by default Green Features The GS110TP Smart PoE Switch supports the following power saving features e The power consumption automatically adjusts based on the RJ 45 cable length e Each port is configured to power down automatically when the port link is down Introduction 1 3 v1 0 March 2010 GS110TP Haraware Installation Guide Package Contents Figure 1 1 shows the package contents of the NETGEAR GS110TP Smart PoE Switch i hia al ra Smart Switch da Resource CD Wall neounting Screws installation Guide Warranty Support Infarmation Card Figure 1 1 Verify that the package contains the following e NETGEAR GS110TP Smart PoE Switch e Rubber footpads for tabletop installation e Wall mounting screws 2 e External power adapter e Installation guide e Smart Switch Resource CD with Netgear Smart Control Center and User s manual If any item is missing or damaged contact the place of purchase immediately 1 4 v1 0 March 2010 Chapter 2 Physical Description This chapter describes the NETGEAR GS110TP Smart PoE Switch hardware features Topics include e GS110TP Front and Ba
17. h cccccssssscceeeceessseeeeeceesseeeeeesasseeeeeeseansees 4 3 Ap Apn AG PO lai ira 4 4 Step 6 Managing the Switch using a Web Browser or the PC Utility 4 4 Appendix A Troubleshooting Wet ct PR ZE T E E A A 1 Additional Troubleshooting Suggestions iiii A 2 Network Adapter Cards cccccccccssssssceceeeeeeseeceeeeeeeeeeeeeseeeseceesssueeeeeeeessuaaeeeeeesaaas A 2 CI A 2 SEA ARR E I CR TATE A 2 MERI paia A 3 Appendix B Technical Specifications Index iv Contents v1 0 March 2010 About This Manual The NETGEAR ProSafe GS110TP Hardware Installation Guide describes how to install and power on the GS11OTP Smart PoE Switch The information in this manual is intended for readers with intermediate computer and Internet skills Conventions Formats and Scope The conventions formats and scope of this manual are described in the following paragraphs e Typographical Conventions This manual uses the following typographical conventions Emphasis books CDs file and server names extensions User input IP addresses GUI screen text Command prompt CLI text code e Formats This manual uses the following formats to highlight special messages Note This format is used to highlight information of importance or special interest Tip This format is used to highlight a procedure that will save time or resources Warning Ignoring this type of note may result
18. ight to test the series for compliance with the regulations Product and Publication Details Model Number Publication Date GS110TP March 2010 Product Family Gigabit Advanced Smart Switch Product Name Home or Business Product Language Publication Part Number Publication Version Number GS110TP Smart PoE Switch Business English 202 10596 01 1 0 v1 0 March 2010 Contents GS110TP Hardware Installation Guide About This Manual Conventions Formats and Scope le V ROW TO PIN DS Nana acri vi Ei A E DE O E E O vi Chapter 1 Introduction EL RR RE A seta pantie aap laonnaeens 1 1 Flea 1 2 POE FO OS eci eolico 1 3 1 3 Polla 1 4 Chapter 2 Physical Description GS110TP Front and Back Panel Configuration irc 2 1 LED A te NIG sciseaninavoidenencenetentute veins imniaoanapaandvananipnigiandaianceastiisndialerialiemaniaisiamnanen 2 2 PEED Giai 2 2 SCIE Ae ESE IZ 2 3 Device Hardware Interfaces ii 2 3 el lai 2 3 Fre POND cilea 2 4 Factory Defaults Button sicinsicnctrpsaivarssinsiveiiduanndeinsanirutnidusiainseddesiniatn oieiaieinsadeiadnindns 2 4 Chapter 3 Applications DoR E ani 3 1 v1 0 March 2010 Chapter 4 Installation Pella ae 4 1 SOI RR aE anainn ES Anian 4 2 Installing the Switch on a Flat Surface u li 4 2 Wall Mounting the Switi PR RE 4 2 Step 3 Checking the Installation ei 4 3 Step 4 Connecting Devices to the Switc
19. ower is disconnected PoE MAX LED e Off There is at least 7W of PoE power available for another device e Solid Yellow Less than 7W of PoE power is available e Flashing Yellow The PoE MAX LED was active in the previous two minutes Device Hardware Interfaces RJ 45 Ports RJ 45 ports are autosensing ports When inserting a cable into an RJ 45 port the switch automatically ascertains the maximum speed 10 100 or 1000 Mbps and duplex mode half duplex or full duplex of the attached device All ports support only unshielded twisted pair UTP cable terminated with an 8 pin RJ 45 plug Physical Description 2 3 v1 0 March 2010 GS110TP Haraware Installation Guide To simplify the procedure for attaching devices all RJ 45 ports support Auto Uplink This technology allows attaching devices to the RJ 45 ports with either straight through or crossover cables When inserting a cable into the switch s RJ 45 port the switch automatically e Senses whether the cable is a straight through or crossover cable e Determines whether the link to the attached device requires a normal connection such as when connecting the port to a PC or an uplink connection such as when connecting the port to a router switch or hub e Configures the RJ 45 port to enable communications with the attached device without requiring user intervention In this way the Auto Uplink technology compensates for setting uplink connections while
20. slow or Half duplex or full duplex Make sure the attached device is set to auto performance degradation setting on the switch and negotiate is a problem the connected device are not the same Troubleshooting A 1 v1 0 March 2010 GS110TP Haraware Installation Guide Table A 1 Troubleshooting Chart Symptom A segment or device is One or more devices are Verify that the cabling is correct Ensure all not recognized as part of not properly connected connectors are securely positioned in the required the network or cabling does not meet ports Equipment may have been accidentally Ethernet guidelines disconnected ACT LED is flashing A network loop Break the loop by ensuring that there is only one continuously on all redundant path has path from any networked device to any other connected ports and the been created networked device network is disabled Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem refer to the troubleshooting suggestions in this section Network Adapter Cards Ensure the network adapter cards installed in the PCs are in working condition and the software driver has been installed Configuration If problems occur after altering the network configuration restore the original connections and determine the problem by implementing the new changes one step at a time Ensure that cable distances repeater limits and other ph
21. ysical aspects of the installation do not exceed the Ethernet limitations Switch Integrity If required verify the integrity of the switch by resetting the switch To reset the switch remove the AC power from the switch and then reapply AC power If the problem continues contact NETGEAR technical support In North America call 1 888 NETGEAR If you are outside of North America please refer to the support information card included with your product A 2 Troubleshooting v1 0 March 2010 GS110TP Hardware Installation Guide Auto Negotiation The RJ 45 ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto negotiation If the device does not support auto negotiation the switch only determines the speed correctly and the duplex mode defaults to half duplex The gigabit port on the Gigabit module negotiates speed duplex mode and flow control provided that the attached device supports auto negotiation Troubleshooting A 3 v1 0 March 2010 GS110TP Haraware Installation Guide A 4 v1 0 March 2010 Troubleshooting Appendix B Technical Specifications Network Protocol and Standards Compatibility IEEE 802 31 10BASE T IEEE 802 3u 100BASE TX IEEE 802 3ab 1000BASE T IEEE 802 3x flow control IEEE 802 3z 1000BASE X IEEE 802 3af DTE Power via MDI Management Windows 2000 XP Vista Microsoft Explorer 6 0 or higher IEEE 802 10 VLAN IEEE 802 3ad Link Aggregation IEEE
Download Pdf Manuals
Related Search