Home

Netgear MVBR1210C User Guide

1. Turn UPnP On Advertisement Period in minutes 30 Advertisement Time To Live in hops 4 UPnP Portmap Table Active Protocol Int Port Ext Port IP Address 2 Fill in the settings on the UPnP screen 3 Turn UPnP On UPnP can be enabled or disabled The default setting for UPnP is enabled If this feature is disabled the router will not allow any device to automatically control the resources such as port forwarding mapping of the router Advertisement Period The advertisement period is how often the router advertises broadcasts its UPnP information This value can range from 1 to 1440 minutes The default period is 30 minutes Shorter durations ensure that control points have current device status at the expense of additional network traffic Longer durations might compromise the freshness of the device status but can significantly reduce network traffic Advertisement Time To Live The time to live for the advertisement is measured in hops for each UPnP packet sent Hops are the number of steps allowed to propagate for each UPnP advertisement before it disappears The number of hops can range from 1 to 255 The default value for the advertisement time to live is 4 hops which should be fine for most home networks If you notice that some devices are not being updated or reached correctly then it might be necessary to increase this value a little UPnP Portmap Table The UPnP Portmap Table displays the IP a
2. Available Folder Name Full path of the network folder Network Folders Volume name Volume name from the storage device either USB drive or HDD Total Free Shows the current utilization of the storage device Space Share Name e You can click the name shown or you can type it in the address field of your web browser e If Not Shared is shown then the default share has been deleted and no other share for the root folder exists Click the link to change this setting Read and Write Shows the network folder permissions and access controls Access All no password allows all users to access the network folder e admin uses the same password that you use to log in to the router main menu Edit button You can click the Edit button to edit the Available Network Folders settings See Edit a Network Folder on page 45 Safely Remove USB Device Click to safely remove the USB device attached to your router See button Unmount a USB Drive on page 48 Edit a Network Folder This process is the same from either the USB Storage Basic Settings screen or the USB Storage Advanced Settings screen Click the Edit button to open the USB Storage Advanced Settings screen USB Storage Basic Settings USB Storage Advanced Settings Network Device Name readyshare Workgroup Workgroup Access Method Link Network Device Name readyshare Available Network Folders Network Connection Weadyshare
3. Folder Name Volume Name sass ee Share Name Taas Space Space Access Vv l D HTTP via internet http 0 0 0 0 shares T r HTTP htto readyshare routerlogin net shares UA U Drive 982MB 856MB _ eadyshare SB Storage 0 password FTP fip readyshare routeriogin net shares FTP via internet ftp 0 0 0 0 shares Edit gt Available Network Folders Safely Remove USB Device Seca Sinai Read Wile nan a Tome Free Access Access Space Space Edit Create Network Folder Delete Apply Refresh You can use this screen to select a folder to change the share name or to change read access or write access from All no password to admin The password for admin is the same one that is used to log in to the router main menu By default it is password USB Storage 45 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Note You need to click Apply for your changes to take effect Configure USB Storage Advanced Settings To configure advanced USB settings from the router menu under USB select Advanced Settings The USB Storage Advanced Settings screen displays USB Storage Advanced Settings Network Device Name readyshare Workgroup Workgroup Access Method Link Port Network Connection weadyshare HTTP htto readyshare routerlogin net shares 80 HTTP via internet http 0 0 0 0 shares 80 FTP ftp readyshare routerlogin ne
4. 1 Log in to the router as described in Log In to Your Router on page 12 2 On the main menu select Block Sites to display the Block Sites screen Block Sites Keyword Blocking Never Block sites containing these keywords or domain names Delete Clear C Allow trusted IP address to visit blocked sites Trusted IP Address Never is selected by default 3 To enable keyword blocking select one of the following e Per Schedule Turn on keyword blocking according to the settings on the Schedule screen Always Turn on keyword blocking all the time independent of the setting in the Schedule screen 4 Enter a keyword or domain in the Keyword field click Add Keyword and then click Apply Some examples of keyword applications are shown in the following chart Keyword Result XXX Block the URL http www badstuf com xxx html com Only websites with other domain suffixes such as edu or gov can be viewed a period Block all Internet browsing access Content Filtering 58 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Up to 32 entries are supported in the Keyword list Note If you block sites you can set up the router to log attempts to access them See View Select and Save Logged Information on page 56 5 To delete a keyword or domain select it from the list click Delete Keyword and then click Apply 6 To specify a trusted user enter that comp
5. 1 Select the entry s radio button 2 Click the Delete button Advanced 91 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 3 Click Apply Dynamic DNS If your network has a permanently assigned IP address you can register a domain name and have that name linked with your IP address by public Domain Name Servers DNS However if your Internet account uses a dynamically assigned IP address you will not know in advance what your IP address will be and the address can change frequently In this case you can use a commercial Dynamic DNS service to register your domain to their IP address and forward traffic directed at your domain to your frequently changing IP address The router contains a client that can connect to a Dynamic DNS service provider To use this feature you need to select a service provider and obtain an account with them After you have configured your account information in the router whenever your ISP assigned IP address changes your router will automatically contact your Dynamic DNS service provider log in to your account and register your new IP address WARNING If your ISP assigns a private WAN IP address such as 192 168 x x or 10 x x x the Dynamic DNS service will not work because private addresses are not routed on the Internet To configure Dynamic DNS 7 From the main menu select Dynamic DNS to display the Dynamic DNS screen 2 Access the website of one of the Dyn
6. Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 3 Settings Fields and check boxes Description Internet Service Provider Select your Internet service provider from the drop down list Access Number The remote site s phone number PIN code Pin code of the SIM card where applicable APN Access point name PDP type Select the type of packet data protocol IP PDP IP PPP PPP IP Connect automatically at startup When this check box is selected the modem automatically connects to the network when powered up This should be selected after login information is provided Roaming automatically When this check box is selected the unit might roam to any available operator in range and might incur roaming charges Use internal antenna If this check box is selected the router will use the internal antenna rather than the external antenna Wireless Button Configuration Select the option to determine what happens when the WPS button on the front panel is pressed e Control Wi Fi Only Pressing the button toggles the WiFi function If WiFi is turned on pressing the button turns off the WiFi Pressing it again turns on the WiFi This function is available only if the WiFi function is enabled The wireless broadband function is unaffected e Control Both Wi Fi and Wireless Broadband Pressing the push button toggles both the WiFi function and wireless broadband
7. Router MAC Address Use Default Address O Use Computer MAC Address Use This MAC Address Apply Test Table 5 Ethernet broadband settings fields when login not required Fields and check boxes Description Account Name If Required This is also Known as the host name or system name For most users type your account name or user name in this field For example if your main mail account is JerAB ISP com then type JerAB in this field If your ISP has given you a specific host name then type it for example CCA7324 A Domain Name If Required For most users you can leave this field blank unless required by your ISP You can type the domain name of your ISP For example if your ISP s mail server is mail xxx yyy zzz you would type xxx yyy zzz as the domain name If you have a domain name given to you by your ISP type it in this field For example Earthlink Cable might require a host name of home and Comcast sometimes supplies a domain name If you have a cable modem this is usually the workgroup name Connecting to the Internet 22 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 5 Ethernet broadband settings fields when login not required continued Fields and check boxes Description Internet IP Address If you log in to your service or your ISP did not provide you with a fixed IP address the router finds an IP address for you automa
8. Type the MAC address of the computer or server Tip f the computer is on your network it is listed on the same screen for your convenience Selecting the radio button for each entry in the attached device list fills in the fields automatically with the computer s MAC address and name Click Apply to enter the reserved address into the table Note The reserved address will not be assigned until the next time the computer contacts the router s DHCP server Reboot the computer or access its IP configuration and force a DHCP release and renew gt To edit or delete a reserved address entry 1 Select the button next to the reserved address you want to edit or delete 2 Click Edit or Delete Advanced 87 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C QoS Setup QoS is an advanced feature that can be used to prioritize some Internet applications and online gaming and to minimize the impact when the bandwidth is busy From the main menu select QoS Setup to display the following screen QoS Setup Enable WMM Wi Fi multi media Settings Turn Internet Access QoS On L Turn Bandwidth Control On Uplink bandwidth Maximum 256 Kbps Automatically check Internet Uplink bandwidth QoS Priority Rule List Setup QoS Rule Field Description Enable WMM Wi Fi Multi media Settings WMM Wireless Multimedia is a subset of the 802 11e standard WMM allows wireless
9. e Make sure the power cord is correctly connected to your router and that the power supply adapter is correctly connected to a functioning power outlet e Check that you are using the power adapter supplied by NETGEAR for this product e If the error persists you might have a hardware problem and should contact technical support Power LED is amber There is a fault within the router Try to clear the fault as follows e Cycle the power to see if the router recovers e Clear the router s configuration to factory defaults This sets the router s IP address to 192 168 0 1 This procedure is explained in Restore the Default Configuration and Password on page 106 If the error persists you might have a hardware problem and should contact technical support Troubleshooting 99 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C LED Action Internet Port K Internet Port LED is off Be sure the SIM card you received is in the router SIM cards from other devices will not function in the router and this SIM card will not function in other devices Internet Port LED is amber The router cannot connect to the Internet Check the Internet connection option being used e For the mobile broadband connection option check the Signal Quality LEDs e For the Ethernet connection option check the WAN Port LED Internet Port LED is blinking amber and green The traffic
10. This week 2 0 00 0 00 0 00 0 00 Refresh Traffic Status Apply Cancel Set up traffic control to issue a warning message before the monthly limit of Mbytes or hours is reached You can select one of the following to occur when the limit is attained e The Internet Port LED flashes green or amber e The Internet connection is disconnected and disabled e Send an email See Enable Security Event Email Notification on page 62 Set up Internet traffic statistics to monitor the data traffic Click the Traffic Status button for a live update on Internet traffic status on your router 10 Click Apply to save your settings Advanced 97 Troubleshooting This chapter gives information about troubleshooting your Mobile Voice HSPA Broadband 11n Wireless Router After each problem description instructions are provided to help you diagnose and solve the problem For the common problems listed go to the section indicated e Is the router on Go to Basic Functioning on page 99 e Have connected the router correctly Go to Basic Functioning on page 99 e can t access the router s configuration with my browser Go to Troubleshoot Access to the Router Main Menu on page 101 e I ve configured the router but can t access the Internet Go to Troubleshoot the ISP Connection on page 102 e I ve configured the router but can t access my local network Go to Troubleshoot a TCP IP Network Using the Ping Utilityon page 104
11. e How do I set daylight savings time Go to Problems with Date and Time on page 105 e want to clear the configuration and start over again Go to Restore the Default Configuration and Password on page 106 98 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Basic Functioning After you turn on power to the router the following sequence of events should occur 71 When power is first applied verify that the Power LED is on 2 After approximately a minute verify that The Power LED is still solid green An amber light indicates the unit has failed its power on self test POST The Internet Port LED is lit The WiFi LED is lit The WiFi radio is on by default The LAN Ports LED is lit when any local ports are connected If a LAN Port LED on the back of the unit is lit a link has been established to the connected device If a LAN port is connected to a 100 Mbps device verify that the port s LED is green If the port is 10 Mbps the LED is amber a 9 The WAN Port LED is lit when the router is connected to a wired modem One of the Signal Quality LEDs is lit when the router has detected a mobile broadband signal e The blue 6 The blue e The blue o LED indicates excellent coverage LED indicates good coverage LED indicates marginal coverage If any of these conditions does not occur refer to the following table LED Action Power O Power LED is off
12. set it to 2 5 Click Apply to save your changes If you added a static route it is added to the Static Routes screen Advanced 94 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Enable Remote Management Using the Remote Management screen you can allow a user or users on the Internet to configure upgrade and check the status of your router Tip Be sure to change the router default password to a very secure password The ideal password should contain no dictionary words from any language and should be a mixture of letters both uppercase and lowercase numbers and symbols Your password can be up to 30 characters gt To configure remote management 7 Log in to the router Type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password 2 Under Advanced select Remote Management Remote Management 3 Select the Turn Remote Management On check box Remote Management Address 4 Specify which external addresses will be allowed f niostise 129 147 123 8080 to access the routers remote management Allow Remote Access By Turn Remote Management On Only This Computer For security restrict access to as few external IP addresses as practical IP Address Range From To e To allow access from any IP address on the everyone Internet select Everyone e To allow access from a range of
13. IP addresses on the Internet select IP Address Range Enter a beginning and ending IP address to define the allowed range e To allow access from a single IP address on the Internet select Only This Computer Enter the IP address that will be allowed access 5 Specify the number of the port that will be used for accessing the router menu Access normally uses the standard HTTP service port 80 For greater security you can enter a different port number Choose a number between 1024 and 65535 but do not use the number of any common service port The default is 8080 which is a common alternate for HTTP 6 Click Apply to have your changes take effect When accessing your router from the Internet type your router WAN IP address in your Internet browser address or location field followed by a colon and the custom port number For example if your external address is 134 177 0 123 and you use port number 8080 enter http 134 177 0 123 8080 Be sure to include http in the address Advanced 95 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Universal Plug and Play Universal Plug and Play UPnP helps devices such as Internet appliances and computers access the network and connect to other devices as needed UPnP devices can automatically discover the services from other registered UPnP devices on the network gt To configure UPnP 7 On the main menu select UPnP to display the UPnP screen UPnP
14. Vonage IP Phone application NetMeeting High NetMeeting application AIM High AIM application 0 0 0 o Google Talk Highest Google Talk application O O Netgear EVA Highest Netgear EVA application SSH High SSH application Telnet High Telnet application VPN High VPN application Normal FTP application Normal SMTP application www Normal WWW application DNS Normal DNS application OIO OO ICMP Normal ICMP application eMule eDonkey Low eMule eDonkey application Kazaa Low Kazaa application 0 0 O Gnutella Low Gnutella application BT Azureus Low BT Azureus application Counter Strike High On line gaming Counter Strike 0 0 O Ages of Empires High On line gaming Age of Empires a QO Everquest High On ine gaming Everquest Quake 2 High On line gaming Quake 2 Quake 3 High On line gaming Quake 3 Unreal Tourment High On line gaming Unreal Tourment 0 0 0 0 Warcraft High On line gaming Warcraft Edit JI Delete Delete All Add Priority Rule Advanced 89 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C QoS Priority Rules From the QoS Priority Rule List click Add Priority Rule to display the following screen QoS Priority rules Priority QoS Policy for Priority Category Applications 4 Applications Add a new Application Priority Normal Specified port range Connection Type TCP UDP Starting Port 1 65535 Ending Port ___ t 65535 For Application
15. Wireless Router MVBR1210C If you want to approve another USB device you need to first click the Safely Remove USB Device button to unmount the currently connected USB device Connect the other USB device and then repeat this process Connect to the USB Drive from a Remote Computer To connect to the USB drive from remote computers using a web browser you need to use the router s Internet port IP address Locate the Internet Port IP Address gt To view the Internet port IP address 1 Log in to the router 2 In the main menu under Maintenance select Router Status 3 Record the IP address that is listed for the Internet port This is the IP address you can use to connect to the router remotely Access the Router s USB Drive Remotely Using FTP gt To connect to the router s USB drive using a web browser 1 Connect to the router by typing ftp and the Internet port IP address in the address field of Internet Explorer or Netscape Navigator for example ftp 10 1 65 4 If you are using Dynamic DNS you can type the DNS name rather than the IP address 2 Type the account name and password that provide access rights to the USB drive 3 The directories of the USB drive that your account has access to display for example share partition1 directory1 You can now read and copy files from the USB directory Connect to the USB Drive with Microsoft Network Settings You can access the USB drive from local computers on
16. and Faxes window Printers and Faxes File Edit View Favorites Tools Help wv J B a Search E Folders Ez Address 4y Printers and Faxes bp Photosmart C5200 series Printer Tasks i gt 4 Add a printer amp Set up faxing See Also 2 Troubleshoot printing Get help with printing Other Places This USB printer is ready The utility does not need to always hold the connection of this USB printer Once there is any print job for this printer the USB utility connects to this USB printer automatically then prints After the print job is done the printer status returns to the Paused state Scan with a Multifunction Printer You can use the scan feature of a multifunction printer 1 Make sure that the printer s status shows as Available 2 Click the Network Scanner button This activates the scanner window that is used to perform the scans USB Printer 54 Content Filtering This chapter describes how to use the basic firewall features of the router to protect your network View Select and Save Logged Information Block Sites and Keywords Block Services Schedule Blocking Enable Security Event Email Notification Note For information about the advanced content filtering features port forwarding and port triggering see Port Forwarding and Port Triggering on page 81 55 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C View Select and Save Logged Information
17. at the same time If WiFi is turned on pressing the button turns off the WiFi At the same time the wireless broadband connection is disconnected If you press the button again WiFi is turned on and the router attempts to reestablish the wireless broadband connection Depending on the coverage wireless broadband coverage might or might not be connected successfully Connection status Current WAN port status Connecting to the Internet 18 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Ethernet Broadband Settings gt To manually configure your Ethernet broadband Internet settings 1 Log in to the router as described in Log In to Your Router on page 12 2 From the main menu select Ethernet Broadband Settings The following question displays at the top of the screen Does Your Internet Connection Require A Login O Yes No Select the option based on the type of account you have with your ISP e If you need to enter login information every time you connect to the Internet or you have a PPPoE account with your ISP select Yes e Otherwise select No Then fill out the appropriate screen For details see one of the following e step a Login required e step b Login not required Note f you have installed PPP software such as WinPoET from Earthlink or Enternet from PacBell then you have PPPoE Select Yes After selecting Yes and configuring your router you do not n
18. encryption keys and data encryption for data security You can select 64 bit or 128 bit encryption See Configure WEP on page 28 WPA PSK TKIP Allow only computers configured with WPA to connect to the router See Configure WPA WPA2 or WPA WPA2 on page 30 WPA2 PSK AES Allow only computers configured with WPA2 to connect to the router See Configure WPA WPA2 or WPA WPA2 on page 30 WPA PSK TKIP WPA2 PSK AES Allow computers configured with either WPA PSK or WPA2 PSK security to connect to the router See Configure WPA WPA2 or WPA WPA2 on page 30 Configure WEP Note If you use a wireless computer to configure wireless security settings you will be disconnected when you click Apply Reconfigure your wireless computer to match the new settings or access the router from a wired computer to make further changes gt To configure WEP data encryption 1 Log in to the router as described in Log In to Your Router on page 12 2 From the main menu select Wireless Settings to display the Wireless Settings screen Wireless Network Configuration 28 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C In the Security Options section select the WEP Wired Equivalent Privacy radio button Security Opts Select the Authentication Type setting Automatic neig Open System or Shared Key The default is Open OwPsrskmori System WPA2 PSK AES WPA PSK TKIP WPA2 PSK
19. for a computer on the For more information see DHCP Settings LAN that computer receives the same IP address each time it on page 86 accesses the router s DHCP server Assign reserved IP addresses to servers that require permanent IP settings DHCP Settings By default the router functions as a Dynamic Host Configuration Protocol DHCP server allowing it to assign IP DNS server and default gateway addresses to all computers connected to the router s LAN The assigned default gateway address is the LAN address of the router IP addresses is assigned to the attached computers from a pool of addresses specified in this screen Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN For most applications the default DHCP and TCP IP settings of the router are satisfactory Use Router as DHCP Server If another device on your network will be the DHCP server or if you will manually configure the network settings of all of your computers clear the Use Router as DHCP Server check box on the LAN Setup screen Otherwise leave it selected Specify the pool of IP addresses to be assigned by filling in the Starting IP Address and Ending IP Address fields These addresses should be part of the same IP address subnet as the router s LAN IP address Using the default addressing scheme you should define a range between 192 168 0 2 and 192 168 0 254 although you might want to save part of the range
20. for this rule if you prefer 5 Click Apply For MAC Addresses gt To set up the priority for a specified computer using its MAC address 1 From the Priority Category list select MAC Address QoS Priority rules Priority QoS Policy for Priority Category MAC Address x MAC Device List QoS Policy Priority Device Name MAC Address Pri_MAC_2BDCF6 Normal ROGERSTECIAK 00 13 02 2B DC F6 Pri_MAC_12133F Normal MPAWLAN SPARE 00 13 02 12 13 3F MAC Address 4 4 A 4 4 Device Name Priority Normal Add Edit Delete Refresh 2 Click the Refresh button to update the list of computers already connected to the router 3 Select the entry s radio button 4 Modify the information in the MAC Address and Device Name fields 5 Select the priority level Highest High Normal or Low 6 You can also type the name in the QoS Policy field for this rule if you prefer 7 Click the Edit button Click Apply gt To add the priority for a specified computer using its MAC address 1 From the Priority Category list select MAC Address 2 Enter the MAC address for the computer for which you are specifying the priority 3 You can also type a name that is easy to remember in the Device Name field 4 Select the priority level Highest High Normal or Low 5 You can also type a name in the QoS Policy field for this rule if you prefer 6 Click the Add button 7 Click Apply gt To delete a priority rule entry
21. is selected 2 You can select a service or add a custom service e Selecta service from the Service Name drop down list and specify the computer s IP address e If you want to add a service that is not in the list click the Add Custom Service button Fill in the fields in the Add Custom Service screen The service displays in the list Advanced 81 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Port Triggering gt To set up port triggering 7 From the main menu under Advanced select Port Forwarding Port Triggering 2 Select the Port Triggering radio button to display the following screen Port Forwarding Port Triggering Please select the service type Port Forwarding Port Triggering Service Name Server IP Address Age of Empire v 192 268 0 Add a Service Name Start Port End Port Server iP Address 3 Click Add Service and fill in the fields in the Add Service screen The service displays in the list For more detailed information see the Port Forwarding Port Triggering help Advanced 82 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C WAN Setup To change broadband Internet connection settings use the Broadband Settings screen as described in Manually Configure Your Internet Settings on page 15 gt To view or change the WAN setup WAN Setup 7 From the main menu select WAN Setup to display the WAN Setup screen 2 Make the changes that you want
22. limit is reached e Download only The restriction is applied to incoming traffic only e Both Directions The restriction is applied to both incoming and outgoing traffic You can limit the amount of data traffic allowed per month by specifying e How many Mbytes per month are allowed e How many hours of traffic are allowed Set the traffic counter to begin at a specific time and date Traffic Meter Traffic Meter Options Show Traffic Meter options for Mobile Broadband Connection Show Traffic Meter options for Ethernet Connection T Enable Traffic Meter for Mobile Broadband Traffic volume control by Mo limit Monthly limit 0 Mbytes 0 Mbytes 0 hours Round up data volume for each connection by Connection time control Monthly limit Traffic Counter Restart traffic counter at p po am z On the ist day of each month Restart Counter Now Traffic Control Pop up a warning message 0 Mbytes Minutes before the monthly limit is reached I Email When the monthly limit is reached IF Turn the Internet LED to flashing green amber IF Disconnect and disable the Internet connection I Email Internet Traffic Statistics Start Date Time Wednesday 01 Jan 2003 00 00 Current Date Time Wednesday 01 Jan 2003 00 39 Traffic Volume Left No limit E Connection Time i Traffic Volume Mbytes hh mm Upload Avg Download Avg Total Ava Today 00 00 0 00 0 00 0 00 Yesterday Period
23. meter feature is enabled and the limit set has been reached WiFi Q WiFi LED is off The WiFi radio has been turned off If you want a WiFi connection with the router press the WiFi button to turn the WiFi radio back on WiFi LED is not If this LED does not blink when you are attempting to send data over the blinking WiFi link log in to the router menu using the Ethernet LAN connection and check your router s wireless WiFi configuration LAN Ports rs LAN Ports LED is off If this LED does not light when an Ethernet connection is made check the following Make sure that the Ethernet cable connections are secure at the router and at the hub or workstation e Make sure that power is turned on to the connected hub or workstation WAN Port Se WAN Port LED is off If this LED does not light when an Ethernet connection is made using the Ethernet connection option check the following Make sure that the Ethernet cable connections are secure at the router and at the modem e Make sure that power is turned on to the modem Signal Quality Signal Quality LEDs are off If these LEDs do not light when the mobile broadband connection option is used check the following e Check with your ISP to ensure that there is good coverage in the area e Ensure that your mobile broadband account is active Ensure that the SIM card is inserted correctly into the router e Locate
24. module vendor Upgrade files can be downloaded from the NETGEAR or module vendor website If the upgrade file is compressed a zip or exe file you need to first extract the binary cwe file before uploading it to the router NETGEAR recommends that you back up your configuration before doing a module firmware upgrade After the upgrade is complete you might need to restore your configuration settings To upgrade the module firmware 1 Download and unzip the new module firmware file from NETGEAR or the module vendor Managing Your Network 73 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C The web browser used to upload new module firmware into the router needs to support HTTP uploads NETGEAR recommends using Microsoft Internet Explorer 5 0 or later or Mozilla Firefox 2 0 or later Log in to the router Type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password From the main menu under Maintenance select Module Upgrade to display this screen Module upgrade Check for new version from the Internet Check Locate and select the upgrade file on your hard disk Choose File No file chosen Upload Cancel Click Browse to locate the binary cwe upgrade file Click Upload A WARNING When uploading module firmware to the router do not interrupt the web browser by closing the window clicking a link or l
25. or multiple IP subnets located on your network Static Route Example As an example of when a static route is needed consider the following case e Your primary Internet access is through a cable modem to an ISP e You have an ISDN router on your home network for connecting to the company where you are employed This router s address on your LAN is 192 168 0 100 e Your company s network is 134 177 0 0 When you first configured your router two implicit static routes were created A default route was created with your ISP as the router and a second static route was created to your local network for all 192 168 0 x addresses With this configuration if you attempt to access a device on the 134 177 0 0 network your router forwards your request to the ISP The ISP forwards your request to the company where you are employed and the request is likely to be denied by the company s firewall In this case you need to define a static route telling your router that 134 177 0 0 should be accessed through the ISDN router at 192 168 0 100 In this example e The Destination IP Address and IP Subnet Mask fields specify that this static route applies to all 134 177 x x addresses e The Gateway IP Address fields specify that all traffic for these addresses should be forwarded to the ISDN router at 192 168 0 100 e Inthe Metric field a value of 1 will work since the ISDN router is on the LAN This represents the number of routers between
26. specified period the log is automatically emailed to the specified email address After the log is sent itis cleared from the router s memory If the router cannot email the log file the log buffer might fill up In this case the router overwrites the log and discards its contents 4 Click Apply so that your changes take effect Content Filtering 62 Managing Your Network This chapter describes how to perform network management tasks with your Mobile Voice HSPA Broadband 11n Wireless Router Router Status View Attached Devices Back Up Restore or Erase Your Settings Protect Access to Your Router Run Diagnostic Utilities and Reboot the Router Upgrade the Router Firmware Upgrade the Module Firmware 63 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Router Status You can use the Router Status screen to view the status of the router to show statistics or to view the connection status gt To view the router status 1 From the main menu under Maintenance select Router Status to view this screen Router Status Active Connection Account Name Firmware Version Ethernet Port MAC Address IP Address Network Type IP Subnet Mask Gateway IP Address Domain Name Server Mobile Broadband Modem Modem Identity Modem SW version Modem driver version IMSI IMEI Operator Network mode Network band Wireless Broadband Port Connection Status IP Address Protocol IP Subnet M
27. te rn et x Control WiFi Only C Control Both WiFi and Wireless Broadband Connection Status Connected Connect Disconnect Apply Cancel Refresh Troubleshoot Internet Browsing If your router can obtain an IP address but your computer is unable to load any web pages from the Internet e The traffic meter is enabled and the limit might have been reached By configuring the traffic meter not to block you can resume Internet access If you have a usage limit your ISP might charge you for the overage e Your computer might not recognize any DNS server addresses A DNS server is a host on the Internet that translates Internet names such as www addresses to numeric IP addresses Typically your ISP provides the addresses of one or Troubleshooting 103 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C two DNS servers for your use If you entered a DNS address during the router s configuration reboot your computer and verify the DNS address Alternatively you can configure your computer manually with DNS addresses as explained in your operating system documentation Your computer might not have the router configured as its TCP IP router If your computer obtains its information from the router by DHCP reboot the computer and verify the router address Troubleshoot a TCP IP Network Using the Ping Utility Most TCP IP terminal devices and routers contain a ping utility that sends an echo request pack
28. triggering are advanced features that affect the behavior of the firewall in your router In the Port Forwarding Port Triggering screen you can make local computers or servers available to the Internet for different services for example FTP or HTTP to play Internet games like Quake III or to use Internet applications like CU SeeMe e Port forwarding is designed for FTP web server or other server based services Once port forwarding is set up requests from the Internet are forwarded to the correct server e Port triggering monitors outbound traffic When the router detects traffic on the specified outbound port it remembers the IP address of the computer that sent the data and triggers the incoming port Incoming traffic on the triggered port is then forwarded to the triggering computer Port triggering allows requests from the Internet only after a designated port is triggered Port triggering applies to chat and Internet games Port Forwarding gt To set up port forwarding 1 From the main menu under Advanced select Port Forwarding Port Triggering The following screen displays Port Forwarding Port Triggering Please select the service type Port Forwarding Port Triggering Service Name Server IP Address Age ofEmpire 192 z68 o Add a Service Name Start Port End Port Server IP Address Edit Senice Delete Serice Add Custom Semice By default the Port Forwarding radio button
29. your home or office network using Microsoft network settings You need to be running Microsoft Windows 2000 XP or older versions of Windows with Microsoft Networking enabled You can use normal Explorer operations such as dragging and dropping opening files or cutting and pasting files from e Microsoft Windows Start menu Run option e Windows Explorer e Network Neighborhood or My Network Place USB Storage 49 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Enable File and Printer Sharing Each computer s network properties need to be set to enable network communication with the USB drive File and Printer Sharing for Microsoft Networking needs to be enabled as described in the following sections Note In Windows 2000 and Windows XP File and Printer Sharing is enabled by default Configure Windows 98SE and Windows ME The easiest way to get to your network properties is to go to your desktop right click Network Neighborhood and then select Properties File and Printer Sharing for Microsoft Windows should be listed If it is not click Add and follow the installation prompts Note f you have any questions about File and Printer Sharing contact Microsoft for assistance Configure Windows 2000 and Windows XP Right click the network connection for your local area network File and Printer Sharing for Microsoft Windows should be listed If it is not click Install and follow the installation prompts
30. your network and the destination This is a direct connection so it is set to 1 e Private is selected only as a precautionary security measure in case RIP is activated Advanced 93 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C gt To configure static routes 1 From the main menu under Advanced select Static Routes to view the Static Routes screen Static Routes Active Name Destination Gateway Ea 2 Select the radio button of the static route you want to configure 3 Click Add or Edit to display the following screen Static Routes Route Name Private VI Active Destination IP Address IP Subnet Mask Gateway IP Address Metric 4 Fill in or change the fields e Route Name The route name is for identification purposes only e Private Select this check box if you want to limit access to the LAN only The static route will not be reported in RIP e Active Select this check box to make this route effective e Destination IP Address and IP Subnet Mask Type the destination IP address of the final destination If the destination is a single host type a subnet value of 255 255 255 255 e Gateway IP Address This needs to be a router on the same LAN segment as the router e Metric Type a number between 2 and 15 This represents the number of routers between your network and the destination Usually a setting of 2 or 3 works but if this is a direct connection
31. 1n Wireless Router MVBR1210C Advanced Wireless Settings From the main menu select Advanced Wireless Settings to display the following screen Advanced Wireless Settings Advanced Wireless Settings M Enable Wireless Router Radio M Enable SSID Broadcast Fragmentation Length 256 2346 2346 CTSIRTS Threshold 1 2347 pa Preamble Mode Long Preamble 7 WPS Settings Routers PIN 17785983 I Disable Routers PIN M Keep Existing Wireless Settings Wireless Card Access List Set Up Access List Apply Cancel Field Description Enable Wireless Router Radio Selected by default this setting enables the wireless radio which allows the router to work as a wireless access point Turning off the wireless radio can be helpful for configuration network tuning or troubleshooting Enable SSID Broadcast The router broadcasts its wireless network name SSID Fragmentation Length CTS RTS These should be left at their default settings Threshold and Preamble Mode Router s PIN The PIN number used for Push N Connect Disable Router s PIN By default this check box is cleared This allows the WPS clients to discover the router s PIN Keep Existing Wireless Settings By default this check box is cleared This allows the router to automatically generate the SSID and WPA WPA2 security settings when it implements WPS After WPS is implemented the router automatically selects the Keep Existing Wireless Setting
32. 33 E0 82 78 Wireless Repeater Repeater IP Address Disable Wireless Client Association Base Station MAC Address Wireless Base Station Disable Wireless Client Association Repeater MAC Address 1 Repeater MAC Address 2 Repeater MAC Address 3 Repeater MAC Address 4 Field Description Enable Wireless Repeating Function Enable this if you wish to use either bridge mode or repeater mode and then select the mode you want for your environment e Wireless Repeater In this mode the MVBR1210C will communicate only with another Base Station mode wireless station You need to enter the MAC address physical address of the other base station mode wireless station in the field provided WEP WPA PSK TKIP can and should be used to protect this communication e Wireless Base Station Select this only if this MVBR1210C is the master for a group of repeater mode wireless stations The other repeater mode wireless stations need to be set to wireless repeater mode using this MVBR1210C s MAC address They then send all traffic to this master rather than communicating directly with each other WEP WPA PSK TKIP can and should be used to protect this traffic If this option is selected you need to enter the MAC addresses of the other access points in the fields provided Advanced 80 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Port Forwarding and Port Triggering Port forwarding and port
33. 5 0 RIP direction None RIP version Disabled RIP authentication None DHCP server Enabled DHCP starting IP address 192 168 0 2 DHCP ending IP address 192 168 0 254 DMZ Disabled Time zone PST for North America Daylight savings time adjustment Enabled Firewall Inbound communication from the Disabled except traffic on port 80 the HTTP port Internet Outbound communication to the Enabled all Internet Source MAC filtering Disabled Supplemental Information 108 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Feature continued Default behavior continued Mobile Internet service provider Bell Mobility broadband APN inet bell ca Access Number 99 PDP Type IP User Name None required WiFi Wireless communication Enabled SSID name See label on the bottom of router Security WPA PSK WPA2 PSK mixed mode Broadcast SSID Enabled Transmission speed Auto Maximum wireless signal rate derived from IEEE Standard 802 11 specifications Actual throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Country region Canada RF channel Auto Operating mode Up to 145 Mbps Data rate Best Output power Full Access point Enabled Authentication type Open system Wireless Card A
34. 64 hex digits wireless connectivity Apply Cancel Set up your wireless computers with the same SSID and wireless security settings as your router Check that they have a wireless link and are able to obtain an IP address by DHCP from the router If there is interference adjust the channel Table 6 Wireless settings Settings Description Wireless Network Name SSID The SSID is also known as the wireless network name Enter a 32 character maximum name in this field This field is case sensitive When there is more than one wireless network SSIDs provide a means for separating the traffic To join a network a wireless computer or device needs to use the SSID Region The location where the router is used Channel The wireless channel used by the gateway The default is Auto Do not change the channel unless you experience interference shown by lost connections or slow data transfers If this happens you might need to try different channels to see which works best Mode The default is Up to 145 Mbps Wireless Network Configuration 27 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 6 Wireless settings continued Settings Security Options Description None Use this setting to establish wireless connectivity before implementing wireless security NETGEAR strongly recommends that you implement wireless security WEP Use
35. AES Note The authentication is separate from the _ Securit Encrypton wer data encryption You can select authentication S that requires a shared key but still leaves data transmissions unencrypted Security is stronger TETT if you use both the Shared Key and WEP kne encryption settings ey2 1 Encryption Strength 64 bit Security Encryption WEP Key Select the Encryption Strength setting Kars e 64 bit Enter 10 hexadecimal digits any Apply Cancer combination of 0 9 a f or A F e 128 bit Enter 26 hexadecimal digits any combination of 0 9 a f or A F Enter the encryption keys You can manually or automatically program the four data encryption keys These values need to be identical on all computers and access points in your network e Passphrase To use a passphrase to generate the keys enter a passphrase and click Generate This automatically creates the keys Wireless stations need to use the passphrase or keys to access the router Note Not all wireless adapters support passphrase key generation e Key 1 Key4 These values are not case sensitive You can manually enter the four data encryption keys These values need to be identical on all computers and access points in your network Enter 10 hexadecimal digits any combination of 0 9 a f or A F Select which of the four keys will be the default Data transmissions are always encrypted using the default key The other keys c
36. Attached Devices MAC Address 00 14 68 5D 8F 19 IP Address 192 168 0 2 Refresh For each device the table shows the IP address device name if available and the Ethernet MAC address If the router is rebooted this data is lost until the router rediscovers the devices To force the router to look for attached devices click the Refresh button Managing Your Network 68 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Back Up Restore or Erase Your Settings The configuration settings of the router are stored in a configuration file in the router This file can be backed up to your computer restored or reverted to factory default settings The procedures in the following sections explain how to do these tasks Back Up the Configuration to a File gt To back up the configuration 1 3 4 Log in to the router Type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password Under Maintenance on the main menu select Backup Settings to display the Backup Settings screen Backup Settings Save a copy of current settings Save Restore saved settings from a file Browse Restore Revert to factory default settings Erase Click Save to save a copy of the current settings Store the cfg file on a computer on your network Restore the Configuration from a File gt To restore the config
37. Broadband 11n Wireless Router MVBR1210C Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet Test the Path from Your Computer to a Remote Device After verifying that the LAN path works correctly test the path from your computer to a remote device gt To test the path 1 From the Windows toolbar click the Start button and select Run 2 In the Windows Run window type ping n 10 P address where P address is the IP address of a remote device such as your ISP s DNS server If the path is functioning correctly replies as in the previous section are displayed If you do not receive replies e Check that your computer has the IP address of your router listed as the default router If the IP configuration of your computer is assigned by DHCP this information is not visible in your computer s Network Control Panel Verify that the IP address of the router is listed as the default router e Make sure that the network address of your computer the portion of the IP address specified by the netmask is different from the network address of the remote device e Check that your cable or DSL modem is connected and functioning e lf your ISP assigned a host name to your computer enter that host name as the account name in the Basic Settings screen e Your ISP could be rejecting the Ethernet MAC addresses of all but one of your computers Many broadband ISPs
38. Connecting to the Internet 9 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 1 LED descriptions continued LED Activity Description Signal Quality Solid blue Excellent coverage has been detected tl All Signal Quality LEDs No coverage has been detected w are off Signal Quality Solid blue Good coverage has been detected C All Signal Quality LEDs No coverage has been detected are off Signal Quality Solid blue Marginal coverage has been detected ae Quality LEDs No coverage has been detected Router Back Panel The back panel of the router contains port connections Connector for optional external antenna WAN port Ethernet LAN ports Phone port USB port Slot for SIM card if required by ISP Power On Off button Power adapter input Connecting to the Internet 10 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Router Label The label on the left side of the router shows the router s MAC address serial number security PIN IMEI or ESN number and factory default login information It also contains the SSID and passphrase that is unique to each router Direction of SIM card insertion Optional USB Power Power Antenna Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C WiFi Network Name SSID Restore Factory Settings user name admin Designed by NETG AR in California WPA WPA2 F SK Passphr
39. IP address to 192 168 0 1 You can erase the current configuration and restore factory defaults in two ways e Use the Erase feature see Erase the Configuration on page 70 e Press the Restore Factory Settings button on the bottom of the router for 6 seconds Use this method for cases when the administration password or IP address is not known The factory default settings are shown in Factory Default Settings on page 108 Troubleshooting 106 Supplemental Information This appendix provides the following information e Factory Default Settings e Technical Specifications 107 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Factory Default Settings Use the Restore Factory Settings button located on the bottom of your router to reset all settings to their original factory default settings This is called a hard reset To perform a hard reset press and hold the Restore Factory Settings button for 6 seconds Your router will return to the factory configuration settings that are shown in the following table Feature Default behavior Router User login URL http www routerlogin net or http www routerlogin com a User name case sensitive admin Login password case sensitive password Internet WAN MAC address Use default address connection WAN MTU size 1500 Port speed AutoSense Local LAN IP 192 168 0 1 network LAN Subnet mask 255 255 25
40. NETGEAR Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C User Manual Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at httos my netgear com You must register your product before you can use NETGEAR telephone support NETGEAR recommends registering your product through the NETGEAR website For product updates and web support visit http support netgear com Phone US amp Canada only 1 888 NETGEAR Phone Other Countries Check the list of phone numbers at http support netgear com general contact default aspx Trademarks NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject to change without notice NETGEAR Inc All rights reserved Table of Contents Chapter 1 Connecting to the Internet Fisttiware Features oodua aaier daian Cea ed Ch eds arenes Ree ea 7 POE GIANG sc cc od pe mc tad ween rE ESARET EENALLE RINKA 7 Router Front Panel ois 64 ccan ected deeded oa awk CMe RRA LR eb RS 8 Revie BaCk Panel scene kgk ics eee niet heereee aden enadaand 10 Former aD te hae wad dada Lat ho edb KAAE AO RE Sao a s 11 LOS ter Your ROU cna che a dd are ade ed ede eae 12 Access th
41. S lookup to find the IP address Display View the internal routing table Typically this information is used only by save siagnostics information technical support Reboot Shut down and restart the router Display the Routing Table Reboot the Router Module data If you reboot the router you will lose your connection To access the router you will need to log in again after it has finished rebooting Save Save the diagnostic information Open View the module data Upgrade the Router Firmware Note This section deals with upgrading the router firmware For information about upgrading the mobile broadband modem firmware see Upgrade the Module Firmware on page 73 The router firmware is stored in flash memory and can be upgraded as new firmware is released by NETGEAR Upgrade files can be downloaded from the NETGEAR website If the upgrade file is compressed a zip file you need to first extract the binary bin or img file before uploading it to the router NETGEAR recommends that you back up your configuration before doing a router firmware upgrade After the upgrade is complete you might need to restore your configuration settings gt To upgrade the router firmware 1 Download and unzip the new router firmware file from NETGEAR The web browser used to upload new router firmware into the router needs to support HTTP uploads NETGEAR recommends using Microsoft Internet Explorer 5 0 or later or Moz
42. Sshaimg SCONANGS rreri aaae EEA E EE EEA 41 Share Photos with Friends and Family 20 0000000 42 Store Files in a Central Location for Printing 0005 42 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Share Large Files with Colleagues 0 0 0c cece eens 42 USB Storage Basic Settings 0 0 eee eee ee 44 Edit a Network Folder sse 6604 4 cc0eceb ewe dearcaaanebheo ena ned 45 Configure USB Storage Advanced SettingS 00 eee eee 46 Create a Network Folder 0 0 0 ccc c eee 47 Unmount a USB Drive 6 ou acak cade eaten k ka inke ek hee ek wae 48 Specify Approved USB Devices in cccikccace cc dee awane a wena was 48 Connect to the USB Drive from a Remote Computer 49 Locate the Internet Port IP Address 00 0c cece eee eee 49 Access the Router s USB Drive Remotely Using FTP 49 Connect to the USB Drive with Microsoft Network Settings 49 Enable File and Printer Sharing 00000c cece cence 50 Chapter 5 USB Printer USB Printer Contellocacceces edie Raw edad OREM SEER KERR S OA 52 Control Center Conmmguraion lt 5 cactapecedeaeadeenmaeenens aes 53 LSE Pie pid y crewed Gye ae de RUNG SORE YER 0 ee os 53 Scan with a Multifunction Printer 0 0 0 000 54 Chapter 6 Content Filtering View Select and Save Logged Information 000005 56 Loy Message Examples 25 lt s ccientada
43. The router logs security related events such as denied incoming service requests hacker probes and administrator logins If you enabled content filtering in the Block Sites screen the Logs screen can show you when someone on your network tries to access a blocked site On the main menu under Content Filtering select Logs to display this screen Current Time Wednesday Jan 01 2003 00 17 53 Remote login from source Remote login from source DHCP IP 192 168 0 2 to MAC address 70 F3 95 B1 E0 SA Remote login from source Initialized firmware version Vi 2 0 9BM manu Remote login from source Remote login from source DHCP IP 192 168 0 2 to MAC address 70 F3 95 B1 E0 SA Initialized firmware version Vi 2 0 95BM manu Refresh Clear Log Send Log Figure 4 Note You can enable email notification to receive these logs in an email message See Enable Security Event Email Notification on page 62 Log entries and action buttons are described in the following table Field or button Description Current time The date and time the log entry was recorded Description or action The type of event and what action was taken if any Source IP The IP address of the initiating device for this log entry Source port and interface The service port number of the initiating device and whether it originated from the LAN or WAN Destination The name or IP address of the destination d
44. USB Storage 50 USB Printer This chapter describes how to access and configure a USB printer attached to your router This chapter includes the following sections e USB Printer Control 51 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C USB Printer Control The USB Control Center utility allows you to control a shared USB device from your computer that is connected to the USB port on your router The utility allows you to control a printer The utility has to be installed on each computer on your network from which you want to control the device You can download this utility at www netgear com landing en us readyshare aspx When you launch the USB Control Center utility a screen similar to the following displays I NETGEAR USB Control Center DAR System Tools About Device Status DA This is the main screen which shows a device icon the description for this USB device and its status Available The device is available from the computer that you are using Waiting to Connect You need to connect to this device from the computer that you are using If this is the first time you are connecting you might be prompted to install the device driver The following menu selections are available e System Exit the utility e Tools Access the Control Center Configuration to set up your shared USB device See the following section Control Center Configuration e About View details about th
45. VoIP applications do not work well with SIP ALG Selecting this check box might help your VoIP devices create or accept a call through the router Advanced 83 secured O Open Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Set Up a Default DMZ Server A WARNING For security reasons you should avoid using the default DMZ server feature When a computer is designated as the default DMZ server it loses much of the protection of the firewall and is exposed to many exploits from the Internet If compromised the computer can be used to attack your network The default DMZ server feature is helpful when you are using some online games and videoconferencing applications that are incompatible with NAT The router is programmed to recognize some of these applications and to work correctly with them but there are other applications that might not function well In some cases one local computer can run the application correctly if that computer s IP address is entered as the default DMZ server Incoming traffic from the Internet is normally discarded by the router unless the traffic is a response to one of your local computers or a service that you have configured in the Port Forwarding Port Triggering screen Instead of discarding this traffic you can have it forwarded to one computer on your network This computer is called the default DMZ server gt To assign a computer or server to be a default DMZ server 1 G
46. WPA2 PSK e WPA PSK TKIP WPA2 PSK AES Wi Fi Protected Access WPA uses a pre shared key to perform authentication and generate the initial data encryption keys The very strong authentication along with dynamic per frame rekeying of WPA makes it virtually impossible to compromise Wireless Network Configuration 26 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Manually Configure Your Wireless Settings Note If you use a wireless computer to change the wireless network name SSID or wireless security you will be disconnected when you click Apply To avoid this occurrence connect your computer directly to the router with an Ethernet cable while you are making changes gt To view or manually configure the wireless settings 1 Log in to the router as described in Log In to Your Router on page 12 2 Select Wireless Settings from the main Wireless Settings menu Wireless Network The settings for this screen are Name SSID Bero Region Canada explained in Table 6 anal sis 3 Select the region in which the router will wei ee operate Security Options None 4 For initial configuration and test leave the wer other settings unchanged 5 To save your changes click Apply WPA PSK TKIP TKIP WPA2 PSK AES WPA PSK TKIP WPA2 PSK AES Security Options WPA PSK WPA2 PSK 6 Configure and test your computers for Passphrase 340702FDD7 8 63 characters or
47. a the operating channel and region need to be set correctly To configure the wireless network you can either specify the wireless settings or you can use Wi Fi Protected Setup WPS to automatically set the SSID and implement WPA WPA2 security e To manually configure the wireless settings you need to know the following SSID The default SSID for the router is NETGEAR 3G The wireless mode 802 11n 802 119 or 802 11b that each wireless adapter supports Wireless security option To successfully implement wireless security check each wireless adapter to determine which wireless security option it supports See Manually Configure Your Wireless Settings on page 27 e Push N Connect WPS implements WPA WPA2 wireless security on the router and your wireless computer or device at the same time The wireless computer or device needs to be compatible with WPS See Use Push N Connect WPS to Configure Your Wireless Network on page 31 Wireless Placement and Range Guidelines The range of your wireless connection can vary significantly based on the physical placement of the router The latency data throughput performance and notebook power consumption of wireless adapters also vary depending on your configuration choices For best results place your router according to the following guidelines e Near the center of the area in which your computers will operate e In an elevated location such as a high shelf where the wir
48. a SMS message over email For multitarget messages you can send a message to multiple phone numbers Each phone number has to be separated by a comma 3 In the Content field enter the content of the SMS message The length of the message is shown at the bottom of the content box 4 Click Send to send the SMS message Alternatively you can also take one of the following actions e Click Clear to remove the information in the To and Content fields e Click Save to save message to Draft e Click Cancel to return to the Inbox without sending the message Voice and Messaging Services 39 USB Storage This chapter describes how to access and configure a USB storage drive attached to your router This chapter includes the following sections e USB Drive Requirements e File Sharing Scenarios e USB Storage Basic Settings e Configure USB Storage Advanced Settings 40 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Unmount a USB Drive Specify Approved USB Devices Connect to the USB Drive from a Remote Computer Connect to the USB Drive with Microsoft Network Settings USB Drive Requirements The router works with 1 0 and 1 1 USB full speed and 2 0 USB high speed standards The approximate USB bus speeds are shown in the following table Bus Data rate USB 1 1 12 Mbits USB 2 0 480 Mbits Actual bus speeds can vary depending on the CPU speed memory speed of the networ
49. aid d Peed ASR AHEM ELAS Spe etaKeeksy Advanced Wireless SettingS 00 cece eee eee eee eee Wireless Station Access Control 00000 cee een eeeee Restrict Access by MAC Address 00 000 cece eee ena Wireless Repeating Function 0 000 e eee eee Port Forwarding and Port Triggering 20200 eee Port FORAN 2 6 ccccctebateeCattbtw ee ehodee a tee dae ewes PO O O A oc aca Soe aves Ate ea he Resale wr A A el WAN SEUD ee eee ee deed Sede RSS ee RRR Code eee we Set Up a Default DMZ Server 000000 LAN SEMP anigadcoraneecastuiuas pawedeed senadideaeseteeaeeks DHOP SES icc ocak Seed a see dd eee ea ERED ORR ERR ED a Messed IP AOC SGR8 2g ncunebere desea RRR RE od RREw RARER Cie ship atu ticaciwiee a detereed a isestaeeua sateen de reeds Gos Priority Rule List occ cccccegs cegdeadgdenncdeacare nance 6S Priory RUES is pueda ne ddaeeddiale eek ae OR ae oR ake Doamne DI i sieaa Dipa dekalb akan wale k ii cas iene adr ek Use Sialic ROUES i ic ceuvende taotud atrio nte dawn bee ede Statie Route ESAT E cis ae do atin Se cena A hak ele hd Geek Reel dea BAD Enable Remote Management 00 00 eee eee Universal Flug and PIS ols ed ee he oe elie ee Red ie ends Thali MGtGF soc dene ce eh ac ee wd eeew deed eee ed CEE Med ew ew eRe we Chapter 9 Troubleshooting Basle PUCK archaea dae heir arden eae O ees Troubleshoot Access to the Router Main Menu Troubleshoot the ISP Connec
50. amic DNS service providers whose names appear in the Service Provider drop down list and register for an account Dynamic DNS Use a Dynamic DNS Service Service Provider www DynDNS org Host Name User Name Password For example for dyndns org go to www dyndns org Cluse Wildcards Apply Cancel Show Status 3 Select the Use a Dynamic DNS Service check box 4 Select the name of your Dynamic DNS service provider 5 Fill in the Host Name User Name and Password fields The Dynamic DNS service provider might call the host name a domain name If your URL is myName dyndns org then your host name is myName The password can be a key for your Dynamic DNS account If your Dynamic DNS provider allows the use of wildcards in resolving your URL you can select the Use wildcards check box to activate this feature For example the wildcard feature will cause yourhost dyndns org to be aliased to the same IP address as yourhost dyndns org Advanced 92 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 6 Click Apply to save your configuration Use Static Routes Static routes provide additional routing information to your router Under normal circumstances the router has adequate routing information after it has been configured for Internet access and you do not need to configure additional static routes You need to configure static routes only for unusual cases such as multiple routers
51. an be used only to decrypt received data The four entries are disabled if WPA PSK or WPA authentication is selected Click Apply to save your settings Wireless Network Configuration 29 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Configure WPA WPA2 or WPA WPA2 Both WPA and WPA2 provide strong data security WPA with TKIP is a software implementation that can be used on Windows systems with Service Pack 2 or later WPA2 with AES is a hardware implementation see your device documentation before implementing it Consult the product documentation for your wireless adapter for instructions for configuring WPA settings Note If you use a wireless computer to configure wireless security settings you will be disconnected when you click Apply If this happens reconfigure your wireless computer to match the new settings or access the router from a wired computer to make further changes To configure WPA or WPA2 in the router 1 2 3 Log in to the router as described in Log In to Your Router on page 12 Select Wireless Settings from the main menu On the Wireless Setting screen select the radio button for the WPA or WPA2 option of your choice For WPA PSK or WPA2 PSK enter the passphrase 5 To save your settings click Apply Wireless Network Configuration 30 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Use Push N Connect WPS to Configure Your Wireless Network For you t
52. and then click Apply Disable Port Scan and DoS Protection C Defaut DMZ Server 192 168 0 o m Respond to Ping on Internet Port to save the settings MTU Size in bytes 1500 NAT Fittering O Disable SIP ALG The WAN Setup fields are described in the following table Setting Description Disable Port Scan and DoS Protection This check box is usually cleared so that the firewall protects your LAN against port scans and denial of service attacks This check box should be selected only in special circumstances Default DMZ Server This feature is sometimes helpful when you are using some online games and videoconferencing Be careful when using this feature because it makes the firewall security less effective See Set Up a Default DMZ Server on page 84 Respond to Ping on Internet Port If you want the router to respond to a ping from the Internet select this check box This should be used only as a diagnostic tool since it allows your router to be discovered Do not select this check box unless you have a specific reason to do so MTU Size Maximum Transmit Unit MTU value For most Ethernet networks this is 1500 bytes or 1492 bytes for PPPoE connections or 1436 bytes for PPTP connections NAT Filtering This is set to Secured to provide a secure firewall to protect computers on the LAN from attacks from the Internet The Open setting is less secure Disable SIP ALG Some
53. anually Configure Your Wireless Settings on page 27 Because WPA randomly creates the SSID and WPA WPA2 keys they might be difficult to type or remember that is one reason why the network is so secure You can change the wireless settings so that they are easier for you to remember If you do that then you will need to set up the WPS compatible computers again Note Making these changes will cause all wireless computers to be disconnected from network You will then have to set them up with the new wireless settings gt To change wireless settings for the network 1 Use an Ethernet cable to connect a computer to the router That way you will not get disconnected when you change the wireless settings 2 Log in to the router and select Wireless Settings see Manually Configure Your Wireless Settings on page 27 3 Make the following changes e Change the wireless network name SSID to a meaningful name e Onthe WPA PSK WPA2 PSK screen select a passphrase e Make sure that the Keep Wireless Settings check box is selected in the Advanced Wireless Settings screen so that your new settings will not be erased if you use WPS 4 Click Apply so that your changes take effect Write down your settings All existing wireless clients are disassociated and disconnected from the router Wireless Network Configuration 33 5 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C For the non WPS devices that you want to con
54. ase Mad SERIAL Router label Restore with unique Router information Factory SSID and Default access address Settings passphrase Default user name and password Press for WPS PIN 6 seconds IMEI or ESN number Serial number MAC address Note Restore Factory Settings Locate the small hole outlined in red on the back of the router Insert a paper clip into the hole and push for 6 seconds Pressing the Restore Factory Settings button causes the LED to blink briefly After the button is held down for more than 6 seconds the LED flashes AMBER and then turns green as the router resets to the factory defaults Connecting to the Internet 11 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Log In to Your Router When you first connect to your router during installation a Setup Wizard displays After the initial configuration you can use your web browser to log in to the router to view or change its settings Links to Knowledge Base and documentation are also available on the router main menu Note Your computer needs to be configured for DHCP For help configuring DHCP refer to the documentation that came with your computer When you have logged in if you do not click Logout after 5 minutes of no activity the router automatically logs you out To log in to the router 1 Type http www routerlogin net in the address field of your browser and then press Enter or Return to display the login w
55. ask Domain Name Server LAN Port MAC Address IP Address DHCP IP Subnet Mask Wireless Port Name SSID Region Channel Wireless AP Broadcast Name Mobile Broadband MVBR1210C V1 2 0 12BM 00 1E 2A 09 4F D5 0 0 0 0 DHCPClient 0 0 0 0 0 0 0 0 MC8704 T2_0_2_1BAP R439 CNSZXD00000128 2011 09 19 17 26 58 v1 7 310410379243026 357597040039806 WCDMA 1900 Connecting 0 0 0 0 PPP 0 0 0 0 0 0 0 0 00 1E 24 09 4F D4 192 168 0 1 ON 255 255 255 0 Bell4FD4 Canada Auto 11 On On Connection Status Refresh Show Statistics You can use the Router Status screen to check the current settings and statistics for your router This screen shows you the current settings If something needs to be changed you will have to change it on the relevant screen e Active Connection This is the current WAN interface the router is using e Router Information Account Name This is the current hardware the router is using Firmware Version This is the current software the router is using This will change if you upgrade your router Ethernet Port These are the current settings that you set in the Setup Wizard or Broadband Account Settings screens Managing Your Network 64 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C MAC Address The physical address of the Router as seen from the Ethernet WAN IP Address Current Internet IP address If assigned dynamically and no Internet conn
56. ccess List All wireless stations allowed Supplemental Information 109 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Technical Specifications Technical specifications Network protocol and standards compatibility TCP IP DHCP Power adapter e North America 120V AC 60 Hz input e 12V DC 2 5A output Physical specifications e Dimensions 6 8 in x 5 03 in x 1 28 in 173 mm x 128 mm x 33 mm e Weight 0 65 lbs without the stand 0 29 kg Environmental specifications e Operating temperature 0 to 40 C 32 to 104 F e Operating humidity 90 maximum relative humidity noncondensing Electromagnetic emissions FCC Part 15 Class B IC EN 55 022 CISPR 22 Class B Interface specifications e LAN 10BASE T or 100BASE Tx RJ 45 e WAN 10BASE T or 100BASE TX RJ 45 Antenna connection optional e SMA connector Supplemental Information 110 Compliance Notification NETGEAR Wireless Routers Gateways APs Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices Failure of the end user to comply with the applicable requirements may result in unlawful operation and adverse action against the end user by the applicable National regulatory authority This product s firmware limits operation to onl
57. ddress of each UPnP device that is currently accessing the router and which ports internal and external that device has opened To save or cancel your changes or refresh the table Click Apply to save the new settings to the router Click Cancel to disregard any unsaved changes Click Refresh to update the portmap table and to show the active ports that are currently opened by UPnP devices Advanced 96 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Traffic Meter Traffic metering allows you to monitor the volume of Internet traffic passing through your router s Internet port With the traffic meter utility you can set limits for traffic volume set a monthly limit and get a live update of traffic usage You enable separate traffic meters for the mobile broadband connection and the Ethernet connection gt To monitor traffic on your router 1 2 8 9 Under Advanced on the router menu select Traffic Meter Select the appropriate Show Traffic Meter Application for radio button for the type of Internet connection mobile broadband or Ethernet you are setting up To enable the traffic meter select the Enable Traffic Meter check box If you would like to record and restrict the volume of Internet traffic select the Traffic volume control by radio button You can select one of the following options for controlling the traffic volume e No Limit No restriction is applied when the traffic
58. display the Wireless Card Access List screen Wireless Card Access List Wireless Station Access List Setup Access List I Turn Access Control On I Device Name MAC Address Add Edit Delete Apply Cancel Adjust the list as needed for your network You can add devices to the Trusted Wireless Stations list Click Add to display the following screen Wireless Card Access List Available Wireless Cards Device Name MAC Ahhess Wireless Card Entry Device Name MAC Address Add Cancel Refresh You can add devices to the list using either of the following methods e If the computer is in the Available Wireless Cards table select its radio button to capture its MAC address e Use the Wireless Card Entry fields to enter the MAC address of the device to be added The MAC address can usually be found on the bottom of the wireless device e If no device name displays when you enter the MAC address you can type a descriptive name for the computer that you are adding Click Apply to save these settings Now only devices on this list will be allowed to wirelessly connect to the router Advanced 79 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Wireless Repeating Function From the main menu select Wireless Repeating Function to display the following screen Wireless Repeating Function Enable Wireless Repeating Function Wireless MAC of this router 00 1F
59. do so now 2 Wireless broadband coverage is available where the unit is located 3 Access the router main menu to verify that the broadband settings are correct Check with your ISP if you are unsure 4 Check the location of the router a Move the router closer to a window for better access to the Internet signal e The blue Signal Quality LED indicates excellent coverage e The blue Signal Quality LED indicates good coverage e The blue Signal Quality LED indicates marginal coverage e No lighted Signal Quality LED indicates no coverage b Maintain recommended minimum distances between NETGEAR equipment and household appliances to reduce interference Troubleshooting 102 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 5 Use an external antenna for improved signal strength lt _ Connector on back panel for optional external antenna UNNI a Install an external antenna The external antenna is an optional accessory that you can purchase Mobile Broadband Settings User Name lt none gt Password lt none gt Country Canada Internet Service Provider Bell Mobility gt _ 6 lt ae b Clear the Use internal antenna APN Fea check box on the Mobile POP Type Broadband Settings screen ee ee and then click Apply G Roaming automatically Use internal antenna c Click Connect to connect to the Wireless Button Configuration n
60. e Setup Wizard after Installation 0000 14 Manually Configure Your Internet Settings 000 000s 15 Broadband Sounds conc cire rie ai Been Chee AE edad ee ewes ks 15 Mobile Broadband Settings 0 0c eee 17 Ethernet Broadband SettingS 0 000 cece eee eee ee 19 Chapter 2 Wireless Network Configuration Plan Your Wireless Network 000000 cece e eee eee eee 25 Wireless Placement and Range Guidelines 0 25 Wireless Security ODUONS cc acu gasdrayetadeuvedsauneeeaGane ae 26 Manually Configure Your Wireless SettingS 000 cea 27 Oe WEP cc canccadenedeeadarceeasaee and eeeaeee wcee ka 28 Configure WPA WPA2 or WPA WPA2 00 0 eee eee 30 Use Push N Connect WPS to Configure Your Wireless Network 31 WPS BUON sesrriiocrs eeri took OER o rie PEro eO EAn Phew 31 WPG PIN EWY s ack Sarna Rk hot dN ay is ai a a ad 32 Add Wireless Computers That Do Not Support WPS 33 SIM Card PIO irik a wee a ieee em ae ad seme anne hn ww al 34 SIM Card Modem Unlock Code 0 0 0 0 00 ccc ees 35 Chapter 3 Voice and Messaging Services eeoa a o E e E AEE es ETT ETET TEET 36 Messaging ServiceS u oro crninituna cedia natu iaaa ka aaa ka 97 View SMS Messages 0 unauna aaa 37 Send SMS Messages coscccsacnreise idista siedasiawav ares 39 Chapter 4 USB Storage USB Drive Requirements 000 cece ee eee 41 File
61. e USB Control Center software USB Printer 52 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Control Center Configuration Select Tools gt Configuration to display the following screen Control Center Configuration Basic Automatically execute when logging on Windows Timeout 30 minute 1 600 Language a Deutsch Francais Italiano Espa ol Danske Note Language setting will take effect on next execution Automatically execute when logging on Windows Select this checkbox to have the utility start automatically when you are logged in to Windows Timeout Specify the time out value for holding the USB resource when it is not in use Language Select the display language for this utility USB Printer The first time you use a printer you need to click Connect You might be asked to install the driver for this printer After the driver is installed the printer status changes to Available Note Some USB printers for example HP and Lexmark printer request that you do not connect the USB cable until you are prompted by the installation software If the USB printer is detected and connected automatically you need to disconnect the printer and then wait for the prompt asking you to click Connect USB Printer 53 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Once the printer shows Available status the grayed out Paused state no longer displays in the Windows Printers
62. e router main menu By default it is password 3 Click Apply so that your changes take effect USB Storage 47 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Unmount a USB Drive A WARNING Unmount the USB drive first before physically unplugging it from the router If the USB disk is removed or a cable is pulled while data is being written to the disk it could result in file or disk corruption To unmount a USB disk drive so that no users can access it from the USB Settings screen click the Safely Remove USB button This takes the drive offline Specify Approved USB Devices You can specify which USB devices are approved for use when connected to the router gt To specify approved USB devices 1 On the router main menu under Advanced select USB Settings USB Settings Enable any USB Device connected tothe USB port Yes ONo Approved Devices Apply 2 Click Approved Devices USB Drive Approved Devices C Allow only approved devices Approved USB Devices Volume Name Device Name UNKNOWN Flash Disk Delete Available USB Devices Volume Name Device Name UNKNOWN Flash Disk Add Apply Retresh 3 On the USB Drive Approved Devices screen select the USB device from the Available USB Devices list 4 Click Add 5 Select the Allow only approved devices check box 6 Click Apply so that your change takes effect USB Storage 48 Mobile Voice HSPA Broadband 11n
63. ected O WPS OPIN Number button 3 Either click the onscreen button or press the WPS button on the front of the router The router tries to communicate with the client the computer that wants to join the network for 2 minutes 4 Go to the client wireless computer and run a WPS configuration utility Follow the utility s instructions to click a WPS button 5 Go back to the router screen to check for a message Wireless Network Configuration 31 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C A message displays confirming that the client was added to the wireless network The router generates an SSID and iii t SS implements WPA WPA2 wireless Security Erbie wireless Router Radio v Enable SSID Broadcast The router will keep these wireless Advanced Wireless Settings Fragmentation Threshold 256 2346 2346 settings unless you change them or you CTSIRTS Threshold 1 2347 2347 clear the Keep Existing Wireless dare Loo Peann Settings check box in the Advanced WPS Settings Routers PIN 83529955 Disable Routers PIN v Keep Existing Wireless Settings Wireless Settings screen 6 Note the new SSID and WPA WPA2 a an ea password for the wireless network You can SSS cussccssstst view these settings in the Wireless Settings screen See Manually Configure Your See See Wireless Settings on page 27 To access the Internet from a
64. ection exists this will be blank or 0 0 0 0 Network Type Type of network client IP Subnet Mask The subnet mask associated with the Internet IP address Gateway IP Address Gateway IP address of the Router Domain Name Server Displays the address of the current DNS Wireless Broadband Modem These are the current settings of mobile broadband device Modem Identity Identity of this USB modem device Modem SW version Software Firmware version of this USB modem device Modem driver version Kernel driver version IMSI International Mobile Subscriber Identity IMEI International Mobile station Equipment Identity Operator The internet service provider name which has connected Network mode Current access technology Network band Current access technology Wireless Broadband Port These are the current settings of mobile broadband WAN Connection Status The current state of the Mobile broadband connection to your cellular ISP IP Address Mobile broadband IP address of the Router Protocol Protocol of the mobile broadband port IP Subnet Mask Subnet mask associated with the mobile broadband IP address Domain Name Server Displays the address of the current DNS LAN Port These are the current settings as set in the LAN IP Setup page MAC Address The physical address of the Router as seen from the local LAN IP Address LAN IP address of the Router DHCP Indicates if the Route
65. eed to run the PPP software on your computer to connect to the Internet a Login required Adjust the settings as needed based on your Internet connection The fields in this screen are described in Table 4 Connecting to the Internet 19 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Ethernet Broadband Settings Does Your Internet Connection Require A Login Yes No Internet Service Provider Login Password Service Name If Required Connection Mode Idie Timeout In Minutes Internet IP Address Get Dynamically From ISP O Use Static IP Address Domain Name Server DNS Address Get Automatically From ISP Use These DNS Servers Primary ONS Secondary DNS Apply Cancel Test Table 4 Ethernet broadband settings when login required Fields and check boxes Description Internet Service Provider Select the service provided by your ISP Other PPPoE is the most common e PPTP is used in Austria and other European countries Telstra BigPond is for Australia only Login This is usually the name that you use in your email address For example if your main mail account is JerAB ISP com then type JerAB in this field Some ISPs such as Mindspring Earthlink and T DSL require that you use your full email address when you log in If your ISP requires your full email address then type it in the Login field Password Type the password that you use to log i
66. elessly connected computers have line of sight access even if through walls e Away from sources of interference such as microwave ovens and 2 4 GHz cordless phones e Away from large metal surfaces e Put the antenna in a vertical position to provide the best side to side coverage Put the antenna in a horizontal position to provide the best up and down coverage e If using multiple access points it is better if adjacent access points use different radio frequency channels to reduce interference The recommended channel spacing between adjacent access points is 5 channels for example use Channels 1 and 6 or 6 and 11 The time it takes to establish a wireless connection can vary depending on both your security settings and placement WEP connections can take slightly longer to establish Also WEP encryption can consume more battery power on a notebook computer Wireless Network Configuration 25 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Wireless Security Options Indoors computers can connect over 802 11n wireless networks at a maximum range of up to 300 feet Such distances can allow others outside your immediate area to access your network Unlike wired network data your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter For this reason use the security features of your wireless equipment The Mobile Voice HSPA Broadband 11n Wireless Router p
67. er s configuration to factory defaults This will set the router s IP address to 192 168 0 1 This procedure is explained in Restore the Default Configuration and Password on page 106 Make sure that your browser has Java JavaScript or ActiveX enabled If you are using Internet Explorer click Refresh to be sure that the Java applet is loaded Try quitting the browser and launching it again Make sure that you are using the correct login information The factory default login name is admin and the password is password Make sure that Caps Lock is off when entering this information If the router does not save changes you have made in the web management interface check the following When entering configuration settings be sure to click the Apply button before moving to another screen or tab or your changes are lost Click the Refresh or Reload button in the web browser The changes might have occurred but the web browser might be caching the old configuration Troubleshooting 101 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Troubleshoot the ISP Connection Check these possible sources of trouble if you are having difficulty connecting to or browsing the Internet Connect to the Internet If unable to connect to Internet check the following 1 The Internet account is active If your ISP has provided you with a SIM card and you have not inserted it into the SIM card slot on the back of the router yet
68. er access to the USB drive in the router 2 She copies the photos from the Mac to the router USB drive 3 The mother uses a web browser or Microsoft Networking to transfer the files from the USB drive to her computer Then she prints the files Share Large Files with Colleagues Sending files larger than 5 MB can pose a problem for many email systems The router allows you to share very large files such as PowerPoint presentations or zip files with colleagues at another site Rather than tying up their mail systems will large files your colleagues can use FTP to easily download shared files from the router gt To share files with a remote colleague 1 To protect your network set up security Create a user name and password for the colleague with appropriate access 2 If you want to limit USB drive access to read only access from the router USB Storage Basic Settings screen click Edit a Network folder In the Write Access field select admin and then click Apply USB Storage 42 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Note The password for admin is the same one that you use to access the router By default it is password 3 Enable FTP via Internet in the USB Storage Advanced Settings screen See Configure USB Storage Advanced Settings on page 46 USB Storage 43 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C USB Storage Basic Settings You can view or edit basic settings
69. et to the designated device The device then responds with an echo reply You can easily troubleshoot a TCP IP network by using the ping utility in your computer Test the LAN Path to Your Router You can ping the router from your computer to verify that the LAN path to your router is set up correctly gt To ping the router from a PC running Windows 95 or later 1 2 3 From the Windows toolbar click the Start button and select Run In the field provided type ping followed by the IP address of the router as in this example ping 192 168 0 1 Click OK You should see a message like this one Pinging lt IP address gt with 32 bytes of data If the path is working you see this message Reply from lt IP address gt bytes 32 time NN ms TTL xxx If the path is not working you see this message Request timed out If the path is not working correctly you could have one of the following problems e Wrong physical connections Make sure that the LAN Ports LED is on If the LED is off follow the instructions in Connect to the Internet on page 102 Check that the corresponding link LEDs are on for your network interface card and for the hub ports if any that are connected to your workstation and router e Wrong network configuration Verify that the Ethernet card driver software and TCP IP software are both installed and configured on your computer or workstation Troubleshooting 104 Mobile Voice HSPA
70. evice or website Destination port and interface The service port number of the destination device and whether it is on the LAN or WAN Refresh button Refresh the log screen Clear Log button Clear the log entries Content Filtering 56 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Field or button Description Send Log button Email the log immediately Apply button Apply the current settings Cancel button Clear the current settings Log Message Examples Following are examples of log messages In all cases the log entry shows the time stamp as Day Year Month Date Hour Minute Second Activation and Administration This entry indicates a power up or reboot with initial time entry Tue 2002 05 21 18 48 39 NETGEAR activated This entry shows an administrator logging in to and out from IP address 192 168 0 2 Tue 2002 05 21 18 55 00 Administrator login successful IP 192 168 0 2 Thu 2002 05 21 18 56 58 Administrator logout IP 192 168 0 2 This entry shows a time out of the administrator login Tue 2002 05 21 19 00 06 Login screen timed out IP 192 168 0 2 This entry shows when the log was emailed Wed 2002 05 22 22 00 19 Log emailed Dropped Packets These entries show an inbound FTP port 21 packet User Datagram Protocol UDP packet port 6970 and Internet Control Message Protocol ICMP packet port 0 being dropped as a
71. f day 105 time zone 61 time out 71 time stamping 61 trademarks 2 traffic counter 97 traffic meter 97 traffic status 97 troubleshooting 98 trusted host 59 U Universal Plug and Play UPnP 96 unmounting USB drive 48 updating firmware 13 USB devices approved 48 USB drive requirements 41 USB drive unmounting 48 USB storage advanced settings 46 basic settings 44 connecting 49 creating network folder 47 editing network folder 45 file sharing scenarios 41 W WAN Port LED 9 WAN setup 83 websites blocking 57 WEP 26 28 WiFi LED 9 WINS 87 wireless access control 77 wireless networks configuring 24 27 wireless repeat function 80 wireless security 26 WPA 26 30 WPA WPA2 30 WPA2 26 30 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C WPS 8 31 PIN entry 32 unsupported 33 116
72. for devices with fixed addresses The router delivers the following parameters to any LAN device that requests DHCP e An IP address from the range you have defined Advanced 86 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Subnet mask Gateway IP address is the router s LAN IP address Primary DNS server if you entered a primary DNS address in the Basic Settings screen otherwise the router s LAN IP address Secondary DNS server if you entered a secondary DNS address in the Basic Settings screen WINS server Windows Internet Naming Service server determines the IP address associated with a particular Windows computer A WINS server records and reports a list of names and IP address of Windows PCs on its local network If you connect to a remote network that contains a WINS server enter the server s IP address here This allows your PCs to browse the network using the Network Neighborhood feature of Windows Reserved IP Addresses When you specify a reserved IP address for a computer on the LAN that computer always receives the same IP address each time it access the router s DHCP server Reserved IP addresses should be assigned to servers that require permanent IP settings gt To reserve an IP address 1 2 3 Click the Add button In the IP Address field type the IP address to assign to the computer or server Choose an IP address from the router s LAN subnet such as 192 168 0 x
73. for the USB storage device attached to your router On the router main menu under USB select Basic Settings The following screen displays USB Storage Basic Settings Network Device Name readyshare Available Network Folders Folder Name Volume Name Total ee Share Name Read Write Space Space Access Access UA U Drive 982 MB 856 MB readyshareUSB Storage Las wel ll ni password password Safely Remove USB Device By default the USB storage device is available to all computers on your local area network LAN To access your USB device from this screen you can click the network or device name or the share name Network or device name p 325s 1 ireadyshare vie readyshare 7 Ge USB_Storage Share name 5S E2 readyshare USB_Storage v Go readyshare USB_Storage Music col Photos You can also type readyshare in the address field of your web browser If you logged in to the router before you connected your USB device you might not see your USB device in the router screens until you log out and then log in again Table 8 USB Storage Basic Settings Fields and buttons Description Network Device Name The default is readyshare This is the name used to access the USB device connected to the router USB Storage 44 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 8 USB Storage Basic Settings continued Fields and buttons Description
74. ge 46 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 9 USB Storage Advanced Settings continued Fields Description Available Share Name e You can click the name shown or you can type it into the address field of Network Folders your web browser e If Not Shared is shown then the default share has been deleted and no other share for the root folder exists Click the link to change this setting Read and Write Shows the permissions and access controls on the network folder Access All no password allows all users to access the network folder admin prompts you to enter the same password that you use to log in to the router main menu Folder Name Full path of the used by the network folder Volume name Volume name from the storage device either USB drive or HDD Total Free The current utilization of the storage device Space Create a Network Folder gt To create a network folder 1 From the USB Storage Advanced Settings screen click the Create Network Folder button to open the Create Network Folder screen Create Network Folder USB Device Ew v Folder Share Name Read Access All no password Write Access All no password 2 Create a folder e You can specify the folder s share name and change read access and write access from All no password to admin e The password for admin is the same one that is used to log in to th
75. gering screen you can set up a schedule for when blocking occurs or when access is not restricted gt To schedule firewall services 1 Log in to the router as described in Log In to Your Router on page 12 2 On the main menu select Schedule The Schedule screen displays 3 To block Internet services based on a schedule select Every Day or select one or more days If you want to limit access completely for the selected days select All Day Otherwise to limit access during certain times for the selected days fill in the Start Blocking and End Blocking fields 4 Enter the values in 24 hour time format For example 10 30 a m would be 10 hours and 30 minutes and 10 30 p m would be 22 hours and 30 minutes If you set the start time after the end time the schedule will be effective through midnight the next day 5 Click Apply to save your changes Content Filtering 61 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Enable Security Event Email Notification To set up the router so that you can receive logs and alerts by email select Email from the router menu to display the following screen gt To receive alerts and logs by email 1 Select the Turn E mail Notification On check box Fill in the fields to send alerts and logs through email 2 E mail Turn E mail Notification On Send alerts and logs thi ough e mail Your Outgoing Mail Server Send to This E mail Address My mail server
76. hange this password to a more secure password The ideal password should contain no dictionary words from any language and should be a mixture of both uppercase and lowercase letters numbers and symbols Your password can be up to 30 characters Change the Built In Password gt To change the password 1 To log in to the router type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password Note If you changed the password and do not remember what it is you can reset the router to its factory default settings See Restore the Default Configuration and Password on page 106 Managing Your Network 70 2 3 4 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C From the main menu under Maintenance select Set Password Set Password Old Password New Password Repeat New Password Administrator login times out after idle for 5 minutes Cancel To change the password first enter the old password and then enter the new password twice Click Apply to save your changes Note After changing the password you need to log in again to continue the configuration If you have backed up the router settings previously you should do a new backup so that the saved settings file includes the new password Change the Administrator Login Time Out For security the administrator login to the router configuration
77. he Service Table on the Block Services screen 7 Click Apply to save your settings Content Filtering 60 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Schedule Blocking The router uses Network Time Protocol NTP to obtain the current time and date from one of several network time servers on the Internet Set Your Time Zone To localize the time for your log entries you need to specify your time zone gt To set the time zone 1 Log in to the router as described in Log In to Your Router on page 12 2 On the main menu under Content Filtering select Schedule 3 Select your time zone This setting will be used for the blocking schedule according to your local time zone and for time stamping log entries If your time zone is currently in daylight savings time select the Automatically adjust for daylight savings time check box 4 Click Apply to save your settings Schedule Firewall Services Schedule Days to Block MeEver Da Sunda Monga Tuesday Wednesday Thursday Frida Saturday Time of day to block use 24 hour clock E Aids Start Blocking Hour Minute End Blocking Hour Minute Time Zone GMT 08 00 Pacific Time US amp Canada Tijuana xv C utomatically adjust for daylight savings time Current Time Wednesday 01 Jan 2003 00 00 24 Apply Cancel If you enabled service blocking in the Block Services screen or port forwarding in the Port Forwarding Port Trig
78. his clear the Enable SSID Broadcast check box on the Advanced Wireless Settings screen and then click Apply Wireless devices will not see your router You need to configure your wireless devices to match the wireless network name SSID of the router Note The SSID of any wireless access adapters needs to match the SSID you configure in the router If they do not match you will not get a wireless connection to the router Restrict Access by MAC Address For increased security you can restrict access to the wireless network to allow only specific computers based on their MAC addresses You can restrict access to only trusted computers so that unknown computers cannot wirelessly connect to the Mobile Voice HSPA Broadband 11n Wireless Router MAC address filtering adds an obstacle against unwanted access to your network but the data broadcast over the wireless link is fully exposed Note f you configure the router from a wireless computer add your computer s MAC address to the access list Otherwise you will lose your wireless connection when you click Apply You need to then access the router from a wired computer or from a wireless computer that is on the access control list to make any further changes Advanced 78 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C gt To restrict access based on MAC addresses 1 From the main menu under Advanced select Wireless Settings Click Set Up Access List to
79. illa Firefox 2 0 or later Managing Your Network 72 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Log in to the router Type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password From the main menu under Maintenance select Router Upgrade to display this screen Router Upgrade Check for new version from the Internet check for new version upon login Locate and select the upgrade file on your hard disk Browse Upload Cancel Click Browse to locate the binary bin or img upgrade file Click Upload A WARNING When uploading firmware to the router do not interrupt the web browser by closing the window clicking a link or loading a new page If the browser is interrupted it might corrupt the firmware causing router to be unworkable and inaccessible When the upload is complete your router will automatically restart The upgrade process typically takes about 1 minute In some cases you might need to clear the configuration and reconfigure the router after upgrading Upgrade the Module Firmware Note This section deals with upgrading the mobile broadband modem firmware For information about upgrading the router firmware see Upgrade the Router Firmware on page 72 The module firmware is stored in flash memory and can be upgraded as new module firmware is released by NETGEAR or the
80. indow User name admin v Password eoescece C Remember my password 2 Enter admin for the user name and your password or the default password 3 For information about how to change the password see Change the Built In Password on page 70 Note f you do not remember your password you can restore the router to its factory default settings which will reset the password See Factory Default Settings on page 108 If the router has not been configured the Smart Wizard screen displays After the router has been configured one of the following screens displays Connecting to the Internet 12 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Firmware Upgrade Assistant screen After initial setup the Firmware Upgrade Assistant screen displays unless the Check for Updated Firmware Upon Log in check box is cleared Note You can disable this automatic checking and updating feature during future log ins by clearing the Check for Updated Firmware Upon Log in check box but NETGEAR recommends that you keep this feature enabled to ensure that your router is using the latest updated firmware Firmware Upgrade Assistant The router is checking the NETGEAR server to see if updated firmware available for your router This could take up to 90 seconds please wait v Check for Updated Firmware Upon Log in Cancel e Router Status screen The Router Status screen displays the cur
81. ing 42 interference 25 internet port LED 9 Internet traffic statistics 97 IP addresses auto generated 101 connecting to USB drive 49 K keywords blocking 57 L label product 11 LAN setup 85 large files sharing 42 LED descriptions 8 log messages 57 logging in and out 12 login not required 21 login required 19 logs 56 logs sending 62 MAC address 105 location of 79 restricting access 26 manual configuration 15 Message Waiting LED 9 114 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C metric static route 94 mobile broadband settings 17 modem unlock code 35 N network folder creating 47 editing 45 network management 63 Network Time Protocol NTP 61 105 P password changing 70 restoring 106 Phone Port LED 9 placement guidelines 25 port forwarding 81 port triggering 81 ports 9 Power LED 9 Push N Connect 31 Q Quality of Service QoS 88 R range guidelines 25 remote management 49 95 removing USB drive 48 reserved IP addresses 87 restoring factory defaults 11 70 restricted access 78 router assembly 7 router status 64 router accessing 70 S sharing files 41 showing statistics 66 signal quality 10 SIM modem unlock 35 PIN code 34 settings 76 SMS Short Message Service configuring 39 SMS LED 9 SMTP 62 static routes 93 status LEDs 8 99 storage drive See USB storage T TCP IP network troubleshooting 104 technical support 2 time o
82. ink detection Failover after 30 In Seconds 3 Adjust the settings as needed based on your Internet connection The fields in this screen are described in Table 2 4 The following buttons are available e Apply Apply the changes that you made e Cancel Discard changes Connecting to the Internet 15 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 2 Internet connection settings Fields and check boxes Description Internet Connection Mode The choices are Always use an Ethernet connection default e Use Ethernet first and if fail use mobile broadband connection e Always use mobile broadband connection Failover Detection Method Select the failover method and enter the related information e DNS lookup using WAN DNS Server e Perform a DNS lookup by a hostname e Ping this IP address Retry Interval is Enter the retry interval Failover after Enter how many retry attempts to make before failing over Resume after Enter how long to wait for the primary link to be stabilized before resuming use of the primary link Enable Hardware link detection When selected the hardware detects when the Ethernet link is dropped Enter when to failover when the Ethernet link is dropped This is independent of the DNS and Ping detection methods 1 This field is available only when the Internet connection mode is Use Ethernet first and if fail use br
83. ion Status The link status Note that LAN2 LAN3 and LAN4 are guest networks TxPkts The number of packets transmitted on this port since reset or manual clear RxPkts The number of packets received on this port since reset or manual clear Collisions The number of collisions on this port since reset or manual clear Tx B s The average egress line utilization for this port Rx B s The average ingress line utilization for this port Up Time The time elapsed since the last power cycle or reset Managing Your Network 66 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Connection Status Click the Connection Status button on the Router Status screen Mobile broadband Status Connection Status Received Signal Quality in dbm Bytes Transmitted Bytes Received Tx Bis Rx Bis System Uptime Connection Status Connection Time Connecting to Server Negotiation Authentication Getting IP Address Getting Network Mask Connected 93 28192417 40438051 7803 3600 00 42 01 00 40 11 ON ON ON 166 129 82 85 255 255 255 255 Poll 5 Interval secs Set Interval Stop Close Window This screen shows the following statistics Field Description Mobile Broadband Status Connection Status The status of the Internet connection e Scanning The modem is scanning for broadband wireless networks in your area e Connected The router is connected to the In
84. k and other variables The router should work with USB 2 0 compliant or 1 1 compliant external flash and hard drives For the most up to date list of USB drives supported by the router go to http kb netgear com app answers detail a_id 12345 When selecting a USB device bear in mind the following The USB port on the router can be used with one USB hard drive at a time Do not attempt to use a USB hub attached to the USB port According to the USB 2 0 specification the maximum available power is 5V at 0 5A Some USB devices might exceed this requirement in which case the device might not function or might function erratically Check the documentation for your USB device to be sure The router supports FAT FAT32 NTFS read and write and Linux file systems File Sharing Scenarios You can share files on the USB drive for a wide variety of business and recreational purposes The files can be any Windows Mac or Linux file type including text Word PowerPoint Excel MP3 picture and multimedia files USB drive applications include Sharing multimedia with friends and family You can share MP3 files pictures and other multimedia with local and remote users Sharing resources on your network Store files in a central location so that you do not have to power up a computer to perform local sharing In addition you can share files between Macintosh Linux and Windows computers by using the USB drive as a go between Sharing file
85. n the user is encouraged to try to correct the interference by one or more of the following methods e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Caution e Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment e This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation e For product available in the USA market only channel 1 11 can be operated Selection of other channels is not possible e This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter Canadian Department of Communications Radio Interference Regulations This digital apparatus Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications This Class B digital apparatus c
86. n to your ISP Service Name If Required If your ISP provided a service name enter it here Otherwise this can be left blank Connecting to the Internet 20 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 4 Ethernet broadband settings when login required continued Fields and check boxes Description Connection Mode Set the connection mode to Dial on Demand Always On or Manually Connect e With the default setting Dial on Demand a PPPoE connection automatically starts when there is outbound traffic to the Internet and it automatically terminates if the connection is idle based on the value in the Idle Timeout field e When the connection mode is set to Always On the PPPoE connection automatically starts when the computer boots up but the connection does not time out The router keeps trying to bring up the connection if it is disconnected for some reason If you select Manually Connect you need to go to the Router Status screen and click the Connect button to connect to the Internet The manual connection does not time out and you have to click the Disconnect button on the Router Status screen to disconnect it Idle Timeout In Minutes An idle Internet connection is terminated after this time period If this value is zero 0 then the router keeps the connection alive by reconnecting immediately whenever the connection is lost Internet IP Address If you l
87. nect open the networking utility and follow the utility s instructions to enter the security settings that you selected in Step 3 the SSID WPA PSK WPA2 PSK security method and passphrase For the WPS devices that you want to connect follow the procedure in WPS Button on page 31 or WPS PIN Entry on page 32 The settings that you configured in Step 3 are broadcast to the WPS devices so that they can connect to the router SIM Card PIN Code Some SIM cards might have a PIN code associated with them Without the PIN code you will not be able to access the Internet This status appears when a PIN is required but has not yet been entered No Internet Connection Available gt To enter the PIN code 1 2 3 Log in to the router and on the main menu under Advanced select Mobile Broadband Settings Enter the PIN code Check with your service provider if you do not know the modem unlock code Mobile Broadband Settings User Name lt none gt Password lt none gt Country Canada ba Internet Service Provider Bell Mobility PIN Code Access Number 998 h APN inet bell ca PDP Type IP X M Connect automatically at startup T Roaming automatically M Use internal antenna Wireless Button Configuration Control Both WiFi and Wireless Control WiFi Only Sapa Connection Status PIN Required Click Apply Wireless Network Configuration 34 Mobile Voice HSPA Broadband 11n Wireless R
88. ngs Internet Connection Mode _Use Ethernetfirst and iffail use mobile broadband connection v b Click Next c Select your country and then your Internet service provider d Click Done Connecting to the Internet 14 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Manually Configure Your Internet Settings For you to connect to the network an active broadband service account is required Contact your ISP for your user name password and the network name You also need to configure some or all of the settings described in the following sections depending on how you have chosen to connect to the Internet e Broadband Settings on page 15 e Mobile Broadband Settings on page 17 not required if using Ethernet connection only e Ethernet Broadband Settings on page 19 not required if using mobile broadband connection only Broadband Settings gt To manually configure your broadband Internet settings 7 Log in to the router as described in Log In to Your Router on page 12 2 From the main menu select Broadband Settings Broadband Settings Internet Connection Mode Use Ethernet connection first and if fail use mobile broadband connection v Failover Detection Method DNS lookup using WAN DNS Server Perform a DNS lookup by a hostname Ping this IP address gt y o _ o Retry Interval is 30 kin Seconds Failover after 4 In Intervals Resume after 60 In Seconds M Enable Hardware l
89. nstalled and operated with minimum distance of 20 cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter FCC Declaration of Conformity We NETGEAR Inc 350 East Plumeria Drive San Jose CA 95134 declare under our sole responsibility that the Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C complies with Part 15 Subpart B of FCC CFR47 Rules Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation 111 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C FCC Radio Frequency Interference Warnings amp Instructions This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and o
90. ny computer connected to your router launch a browser such as Microsoft Internet Explorer or Mozilla Firefox You should see the router s Internet Port LED blink indicating communication to the ISP Note If no WPS capable client devices are located during the 2 minute time frame the SSID does not change and no security is set up WPS PIN Entry Any wireless computer or device that will connect to the router wirelessly is a client The client needs to support a WPS PIN and needs to have a WPS configuration utility such as the NETGEAR Smart Wizard or Atheros Jumpstart The first time you add a WPS client make sure that the Keep Existing Wireless Settings check box on the Advanced Wireless Settings screen is cleared This is the default setting for the router and allows it to generate the SSID and WPA WPA2 security settings when it implements WPS After WPS is implemented the router automatically selects this check box so that your SSID and wireless security settings stay the same if other WPS devices are added later gt To use a PIN to add a WPS client 1 Log in to the router as described in Log In to Your Router on page 12 2 On the router main menu select Add WPS Client computers that will connect wirelessly to the router are clients and then click Next The Add WPS Client screen displays 3 Select the PIN Number radio button Add WPS Client Select a setup method Push Button recommended PIN Numbe
91. o to the WAN Setup screen as described in the previous section 2 Select the Default DMZ Server check box 3 Type the IP address for that server 4 Click Apply to save your changes Advanced 84 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C LAN Setup The LAN Setup screen allows configuration of LAN IP services such as DHCP and RIP These features can be found under Advanced in the router main menu The router is shipped preconfigured to use private IP addresses on the LAN side and to act as a DHCP server The router default LAN IP configuration is e LAN IP address 192 168 0 1 e Subnet mask 255 255 255 0 These addresses are part of the Internet Engineering Task Force IETF designated private address range for use in private networks and should be suitable in most applications If your network has a requirement to use a different IP addressing scheme you can make those changes in this screen Tip If you change the LAN IP address of the router while connected through the browser you will be disconnected and so will others connected to the router To connect to the router you need to open a new connection to the new IP address and log in again Others using the router need to restart their computers to connect to the router again gt To view or change the LAN setup 1 Select LAN IP to display the LAN Setup screen LAN Setup Device Name IMVBR1210C LAN TCP IP Setup IP Address fusz fase fo f
92. o use Push N Connect your wireless computers or devices need to support Wi Fi Protected Setup WPS Compatible equipment usually has the Ey WPS symbol on it WPS can configure the network name SSID and set up WPA WPA2 wireless security for the router and the wireless computer or device at the same time Here are some considerations to consider when planning on using WPS to configure your wireless network e NETGEAR s Push N Connect feature is based on the WPS standard All other WiFi certified and WPS capable products should be compatible with NETGEAR products that implement Push N Connect e If your wireless network will include a combination of WPS capable devices and non WPS capable devices NETGEAR suggests that you set up your wireless network and security settings manually first and use WPS only for adding WPS capable devices WPS Button Any wireless computer or wireless adapter that will connect to the router wirelessly is a client The client needs to support a WPS button and needs to have a WPS configuration utility such as the NETGEAR Smart Wizard or Atheros Jumpstart gt To use the router WPS button to add a WPS client 1 Log in to the router as described in Log In to Your Router on page 12 2 On the router main menu select Add Mansa WPS Client and then click Next By default the Push Button on reco mme nded radio butto n is ae the Push Button physically on the router or press the Button below sel
93. oadband connection Connecting to the Internet 16 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Mobile Broadband Settings gt To manually configure your mobile broadband Internet settings 1 Log in to the router as described in Log In to Your Router on page 12 2 From the main menu select Mobile Broadband Settings Mobile Broadband Settings User Name lt none gt Password lt none gt Country Canada gt Internet Service Provider Bell Mobility gt Access Number 99 1 gt APN finetbell ca PDP Type IP ha M Connect automatically at startup E Roaming automatically M Use internal antenna Wireless Button Configuration Control WiFi Only Control Both WiFi and Wireless Broadband Connection Status Connected Connect Disconnect Apply Cancel Refresh 3 Adjust the settings as needed based on your Internet connection The fields in this screen are described in Table 3 4 Available buttons are e Connect Manually connect to the network e Disconnect Disconnect from the current network e Apply Apply the changes that you made e Cancel Discard changes e Refresh Update the connection status Table 3 Settings Fields and check boxes Description User Name Internet account login user name Password Internet account password for authentication Country Select your country from the drop down list Connecting to the Internet 17
94. oading a new page If the browser is interrupted it might corrupt the firmware causing router to be unworkable and inaccessible When the upload is complete your router will automatically restart The upgrade process typically takes about 1 minute In some cases you might need to clear the configuration and reconfigure the router after upgrading Managing Your Network 74 Advanced This chapter describes how to configure the advanced features of your Mobile Voice HSPA Broadband 11n Wireless Router e SIM Settings e Advanced Wireless Settings e Wireless Repeating Function Port Forwarding and Port Triggering e WAN Setup e LAN Setup e QoS Setup e Dynamic DNS e Use Static Routes e Enable Remote Management e Universal Plug and Play e Traffic Meter 75 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C SIM Settings From the main menu select SIM Settings to display the following screen SIM Settings Enabling or Disabling the PIN Code Disable O Enable Current PIN Code Changing the PIN Code Current PIN Code New PIN Code Confirm new PIN Code SIM status Field Description Enabling or Disabling the PIN Code Controls whether the PIN code on the SIM card will be used to connect to the network Changing the PIN Code Changes the PIN code on the SIM card SIM status Current SIM card access status Advanced 76 Mobile Voice HSPA Broadband 1
95. odes are One beep feature not active Two beeps feature active Messaging Services Short Message Service SMS is a text messaging service for communication systems The SMS screens enable you to perform the tasks that are explained in the following sections e View SMS Messages e Send SMS Messages View SMS Messages New SMS messages are available when the SMS SMS LED on the front panel is solid green gt To view new SMS messages 1 On the main menu under Advanced select SMS Messages and then select Inbox from the drop down list to display the SMS Message screen SMS Message Inbox 7 Messages used allowed SIM card unknow New Forward Reply Delete Refresh Delete All 2 Click a particular message to view it Voice and Messaging Services 37 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C e Click Forward or Reply to forward or reply to the specified message e Click Delete to delete the specified SMS message 3 Otherwise do one of the following e Click Refresh to redisplay all SMS messages from the SIM card e Click Delete All to delete all SMS messages from the SIM card e Click New to open a new message See Send SMS Messages on page 39 for more information gt To view sent SMS messages 7 On the main menu under Advanced select SMS Settings and then select Sent from the drop down list to display the SMS Message screen SMS Message Sent Message
96. og in to your service or your ISP did not provide you with a fixed IP address the router finds an IP address for you automatically when you connect Select Get Dynamically from ISP If you have a fixed static permanent IP address your ISP has provided you with an IP address Select Use Static IP Address and type the IP address Domain Name Server DNS Address The DNS server is used to look up site addresses based on their names e If your ISP gave you one or two DNS addresses select Use These DNS Servers and type the primary and secondary addresses e Otherwise select Get Automatically From ISP Note If you get Address not found errors when you go to a website it is likely that your DNS servers are not set up correctly You should contact your ISP to get DNS server addresses b Login not required Adjust the settings as needed based on your Internet connection The fields in this screen are described in Table 5 Connecting to the Internet 21 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Ethernet Broadband Settings Does Your Internet Connection Require A Login Yes No Account Name if Required Domain Name If Required internet IP Address Get Dynamically From ISP Use Static IP Address IP Address IP Subnet Mask Gateway IP Address Domain Name Server DNS Address Get Automatically From ISP O Use These DNS Servers Primary DNS Secondary DNS
97. omplies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Industry Canada This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Caution Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage regu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Compliance Notification 112 Mobile Voice HSPA Broadband 11n Wireless Ro
98. once a value has already been set in the Use This MAC Address selection 3 The following buttons are available Apply Apply the changes that you made Cancel Discard changes Test Connect to the NETGEAR website If you connect successfully your settings work and you can click Logout to exit these screens Connecting to the Internet 23 Wireless Network Configuration For a wireless connection the SSID also known as the wireless network name and the wireless security settings need to be the same for the router and wireless computers or wireless adapters NETGEAR strongly recommends that you use wireless security The router is preconfigured with WPA PSK WPA2 PSK mixed mode and uses a unique SSID and passphrase This information is printed on the label on the bottom of the router Use this information to setup your WiFi computer and devices This chapter incudes the following sections Plan Your Wireless Network Manually Configure Your Wireless Settings Use Push N Connect WPS to Configure Your Wireless Network SIM Card PIN Code SIM Card Modem Unlock Code Note Computers can connect wirelessly at a range of several hundred feet If you do not use wireless security this can allow others outside your immediate area to access your network 24 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Plan Your Wireless Network For compliance and compatibility between similar products in your are
99. outer MVBR1210C SIM Card Modem Unlock Code If you have a SIM card that is not provided by the company where you got the router you might get an error indicating that the modem is locked To proceed you need to enter an unlock code No Internet Connection Avaliable dem U k Code Required gt To enter the modem unlock code 1 Log in to the router and on the main menu under Advanced select Mobile Broadband Settings 2 Enter the modem unlock code The modem unlock code can be obtained from your service provider Mobile Broadband Settings User Name lt none gt Password lt none gt Country Canada X Internet Service Provider Bell Mobility Modem unlock code Access Number 99 x APN inet_bell ca PDP Type IP Connect automatically at startup T Roaming automatically Use internal antenna Wireless Button Configuration c wi Control WiFi Only Control Both WiFi and Wireless Broadband Connection Status Modem Unlock Code Required 3 Click Apply Wireless Network Configuration 35 Voice and Messaging Services The Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C provides voice and messaging services This chapter covers the following topics e Voice Services e Messaging Services Note The voice and messaging services are available only when the SIM card is inserted and the router is connected to the mobile broadband service Voice Services Voice services use the follo
100. r Ifyour Adapter supports WPS please click on Generate a client Security Pin to input on the AP Router Gateway and put the generated client PIN number here Enter Client s PIN Next Wireless Network Configuration 32 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 4 Go to the client wireless computer Run a WPS configuration utility Follow the utility s instructions to generate a PIN Take note of the client PIN 5 Inthe router Add WPS Client screen enter the client PIN number and then click Next e The router tries to communicate with the client for 4 minutes If no WPS clients connect during this time the router wireless settings do not change e The router WPS screen confirms that the client was added to the wireless network The router generates an SSID and implements WPA WPA2 wireless security 6 Note the new SSID and WPA WPA2 password for the wireless network You can view these settings in the Wireless Settings screen See Manually Configure Your Wireless Settings on page 27 To access the Internet from any computer connected to your router launch an Internet browser such as Mozilla Firefox You should see the router s Internet LED blink Add Wireless Computers That Do Not Support WPS If you set up your network with WPS and now you want to add a computer that does not support WPS you need to manually configure that computer For information about how to view the wireless settings for the router see M
101. r is acting as a DHCP Server for devices on your LAN IP Subnet Mask Subnet mask associated with the LAN IP address Wireless Port These are the current settings as set in the Wireless Settings page Name SSID SSID of the Router Region The location country Channel The current channel in use Wireless AP Indicates if the Access Point feature of the Router is enabled or not If not enabled the Wireless LED on the front panel will be off Broadcast Name Indicates if the Router is broadcasting its SSID Managing Your Network 65 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 2 Click Show Statistics to see router performance statistics such as the number of packets sent and number of packets received for each port See Showing Statistics on page 66 for information about statistics 3 Click Connection Status to see information about your current connection For information about the Internet connection see Connection Status on page 67 Showing Statistics Click the Show Statistics button on the Router Status screen to display router usage statistics System Up Time 00 10 53 Port Status TxPkts RxPkts Collisions Tx B s Rx Bis Up Time WAN PPP 150 33 0 0 0 00 10 09 LAN1 10M 100M 00 10 53 LAN2 Link Down LAN3 Link Down LAN4 Link Down WLAN 300M 1041 827 Poll Interval 5 Set Interval The following table explains the statistic fields Field Descript
102. rent router connection status See Router Status on page 64 4 You can use different methods to configure your router e Select Setup Wizard from the router menu to set up your Internet connection and wireless network configuration See Access the Setup Wizard after Installation on page 14 e You can manually configure the router settings See Manually Configure Your Internet Settings on page 15 Connecting to the Internet 13 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Access the Setup Wizard after Installation gt To access the Setup Wizard 7 Log in to the router as described in Log In to Your Router on page 12 The Setup Wizard opens You are now connected to the NETGEAR Ethernet Mobile Broadband Wireless Router This Setup Wizard will guide you through m Setting up Ethernet WAN internet access m Setting up Mobile broadband internet access m Setting up a secure Wi Fi network Before you begin please ensure your mobile broadband account is active To upgrade your device download the firmware then click Upgrade To configure your router settings manually click Exit Upgrade Exit 2 Click Next The Setup Wizard prompts you to set up your Internet connection and wireless network a Select your Internet connection mode e Use Ethernet first and if fail use mobile broadband connection e Always use mobile broadband connection e Always use Ethernet connection Broadband Setti
103. requires authentication User Name Password Send Alert inmediately When someone attempts to visit a blocked site Your Outgoing Mail Server Enter the name or IP address of the outgoing SMTP mail server of your ISP Such as mail mylSP com Send to This Email Address Enter the email address where you want to send the alerts and logs Use a full email address such as ChrisXY mylISP com My mail server requires authentication Select this check box if you need to log in to your SMTP server to send email If you select this feature you need to enter the user name and password for the mail server Send logs according to this schedule Day Time am pm Apply Cancel Tip f you cannot remember this information check the settings in your email program Specify when you want the alerts and logs to be sent Send alert immediately Select this check box if you would like immediate notification of a significant security event such as a known attack port scan or attempted access to a blocked site Send logs according to this schedule Specifies how often to send the logs Hourly Daily Weekly or When Full Day for sending log Specifies which day of the week to send the log Relevant when the log is sent weekly Time for sending log Specifies the time of day to send the log Relevant when the log is sent daily or weekly If the Weekly Daily or Hourly option is selected and the log fills up before the
104. restrict access by allowing only traffic from the MAC address of your broadband modem but some ISPs additionally restrict access to the MAC address of a single computer connected to that modem If this is the case you need to configure your router to clone or spoof the MAC address from the authorized computer Problems with Date and Time The Email screen displays the current date and time of day The Mobile Voice HSPA Broadband 11n Wireless Router uses the Network Time Protocol NTP to obtain the current time from one of several network time servers on the Internet Each entry in the log is stamped with the date and time of day Problems with the date and time function can include the following e Date shown is January 1 2000 Cause The router has not yet successfully reached a network time server Check that your Internet access settings are configured correctly If you have just completed configuring the router wait at least 5 minutes and check the date and time again Troubleshooting 105 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C e Time is off by one hour Cause The router does not automatically sense daylight savings time On the E mail screen select or clear the Automatically adjust for Daylight Savings Time check box Restore the Default Configuration and Password This section explains how to restore the factory default configuration settings changing the router s admin password to password and the
105. result of the default inbound rule which states that all inbound packets are denied Wed 2002 05 22 07 15 15 TCP packet dropped Source 64 12 47 28 4787 WAN Destination 134 177 0 11 21 LAN Inbound Default rule match Sun 2002 05 22 12 50 33 UDP packet dropped Source 64 12 47 28 10714 WAN Destination 134 177 0 11 6970 LAN Inbound Default rule match Sun 2002 05 22 21 02 53 ICMP packet dropped Source 64 12 47 28 0 WAN Destination 134 177 0 11 0 LAN Inbound Default rule match Block Sites and Keywords The router provides a variety of options for blocking Internet based content and communications services With its content filtering feature the router prevents objectionable content from reaching your computers You can control access to Internet content by screening for keywords within web addresses Content filtering options include Content Filtering 57 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C e Keyword blocking of HTTP traffic e Outbound service blocking Limits access from your LAN to Internet locations or services that you specify as off limits e Denial of service DoS protection Detects and thwarts DoS attacks such as Ping of Death SYN flood LAND attack and IP spoofing e Blocking unwanted traffic from the Internet to your LAN The router allows you to restrict access to Internet content based on web addresses and web address keywords To block sites and keywords
106. rovides highly effective security features which are covered in detail in this chapter Deploy the security features appropriate to your needs Each router is preconfigured for WPA PSK WPA2 PSK mixed mode and comes with a unique SSID and passphrase There are several ways you can enhance the security of your wireless network Wireless Data Security Options Range up to 300 feet radius 1 Open system easy but no security 2 MAC access list no data security MVBR1210C 3 WEP security but some performance impact 4 WPA PSK strong security 5 WPA2 PSK very strong security Figure 3 Wireless security e Restrict access based on MAC address You can allow only trusted computers to connect so that unknown computers cannot wirelessly connect to the router Restricting access by MAC address adds an obstacle against unwanted access to your network but the data broadcast over the wireless link is fully exposed e Turn off the broadcast of the wireless network name SSID If you disable broadcast of the SSID only devices that have the correct SSID can connect This nullifies wireless network discovery feature of some products such as Windows XP but the data is still exposed e WEP Wired Equivalent Privacy WEP data encryption provides data security WEP Shared Key authentication and WEP data encryption block all but the most determined eavesdropper This data encryption mode has been superseded by WPA PSK and
107. rsiceva deedaa dewbae 4A 57 Block Sites and KeyWords bic ad bade eh eda aa das Bf BGK SENGES 6 coca cheer hehe deel uapucadeneardedsl del eshewae 60 peme dule BIGGIE c3 janx toes ikea ee eee bad 61 Set Your Tine ZOB oo 2card enki ie eat ouad bee hapa dines x 61 Schedule Firewall Services 0 0c cee eas 61 Enable Security Event Email Notification 0000000 62 Chapter 7 Managing Your Network Ge Led gee f 1 Cae ee ee me ee re rn ar er era vane a eer ee 64 SHOW Slas eE 2320 ei ees evens bode RESKG ET SOS Hekate aed 2s 66 Connection Status 4 256 2dkka RARER KEK RRRES RAE AG ERRORS CREWS 4 67 View Attached Devices 000 cece eee eee 68 Back Up Restore or Erase Your Settings 20 00 000ee 69 Back Up the Configuration to a File 2 2 0 0 000 cee eee eae 69 Restore the Configuration from a File 2 0 0 0 000 c cee eee 69 Erase he COntquration ncccaccceenvsteeeGaunew cere aana 70 Protect Access to Your Router aaaaaaa doce ak a ieee a 70 Change the Built In Password 0 000 e ene eas 70 Change the Administrator Login Time Out 00005 71 Run Diagnostic Utilities and Reboot the Router 71 Upgrade the Router Firmware 00 cece eee eee eee 72 Upgrade the Module Firmware 000 cece eee eee 73 Chapter 8 Advanced Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C I GUIS 1 eed ae Rid
108. s check box so that your SSID and wireless security settings remain the same if other WPS enabled devices are added later Set Up Access List Access control is disabled by default so that any computer configured with the correct SSID can connect See Restrict Access by MAC Address on page 78 Wireless Station Access Control By default any wireless computer configured with the correct SSID and wireless security settings is allowed access to your wireless network You can use wireless access point settings in the Wireless Settings screen to further restrict wireless access to your network Advanced 77 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C e Turn off wireless connectivity completely You can completely turn off the wireless portion of the router For example if you use your notebook computer to wirelessly connect to your router and you take a business trip you can turn off the wireless portion of the router while you are traveling Other members of your household who use computers connected to the router through Ethernet cables can still use the router To do this clear the Enable Wireless Router Radio check box on the Advanced Wireless Settings screen and then click Apply e Hide your wireless network name SSID By default the router is set to broadcast its wireless network name SSID You can restrict wireless access to your network by not broadcasting the wireless network name SSID To do t
109. s or Online Gaming gt To set up the priority for an application or online gaming 1 From the Priority Category list select Applications or On line Gaming QoS Priority rules QoS Priority rules Priority Priority QoS Policy for QoS Policy for Priority Category Applications E Priority Category Onine Gaming Applications Add a new Application Applications Add a new Game Priority Normal x Priority Normal Specified port range i Specified port range Connection Type TCP UDP Connection Type TCP UDP Starting Port 1 65535 Starting Port 1 65535 Ending Port 1 65535 Ending Port 1 65535 2 Select the Internet application or game for which you want to set the priority from the relevant list 3 Select the priority level Highest High Normal or Low 4 You can also type the name in the QoS Policy field for this rule if you prefer 5 Click Apply For Ethernet LAN Ports gt To set up the priority for a LAN port 1 From the Priority Category list select Ethernet LAN Port QoS Priority rules Priority QoS Policy for LAN Port 1 Priority Category LAN port Priority Normal Advanced 90 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 2 Select the number of LAN ports for which you want to specify the priority level for those computers connecting on this LAN port 3 Select the priority level Highest High Normal or Low 4 You can also type the name in the QoS Policy field
110. s used allowed 0 30 New Forward Resend Delete 2 Click a particular message to display it e Click Forward to forward the specified SMS message e Click Resend to resend the specified SMS message e Click Delete to delete the specified SMS message 3 Click New to open a new message See Send SMS Messages on page 39 for more information gt To view draft SMS messages 7 On the main menu under Advanced select SMS Settings and then select Draft from the drop down list to display the SMS Message screen SMS Message Draft Message used allowed 0 30 New Edit Send Delete Voice and Messaging Services 38 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C 2 Click a particular message to display it e Click Edit to edit the specified SMS message e Click Send to send the specified SMS message e Click Delete to delete the specified SMS message 3 Click New to open a new message See Send SMS Messages on page 39 for more information Send SMS Messages You can create a new SMS message or send an SMS message over email gt To send SMS messages 1 From either the SMS Message Inbox or Sent screen click New to display the SMS Message Compose screen SMS Message Compose Page To 0 160 using 7 bit alphabet Send Clear Save Cancel 2 Inthe To field enter the phone number that you want to send your SMS message to or the email address to send
111. s with offsite coworkers Share files such as Word documents PowerPoint presentations and text files with remote users USB Storage 41 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C A few common uses are described in the following sections Share Photos with Friends and Family You can create your own central storage location for photos and multimedia This eliminates the need to log in to and pay for an external photo sharing site gt To share files with your friends and family 7 Insert your USB drive into the USB port on the router either directly or with a USB cable Computers on your local area network LAN can access this USB drive using a web browser or Microsoft Networking 2 lf you want to specify read only access or to allow access from the Internet see Configure USB Storage Advanced Settings on page 46 Store Files in a Central Location for Printing This scenario is for a family that has one high quality color printer directly attached to a computer but not shared on the local area network LAN This family does not have a print server e The family s color printer is directly attached to the mother s computer e The daughter has some photos on her Macintosh computer that she wants to print e Their computers are not visible to each other on the network gt To print her photos on the color printer 1 The daughter types readyshare in the address field of her web browser This gives h
112. t shares 21 FTP via internet ftp 0 0 0 0 shares 21 Available Network Folders Share Name Read Write Folder Name Access Access Total Free Volume Name Space Space Edit Create Network Folder Delete Apply Refresh You can use this screen to specify access to the USB storage device The following table explains the fields and buttons in the USB Storage Advanced Settings screen Table 9 USB Storage Advanced Settings Fields Description Network Device Name The default is readyshare This is the name used to access the USB device connected to the router from your computer Workgroup If you are using a Windows workgroup rather than a domain the workgroup name is displayed here Access Method Network Connection Enabled by default this allows all users on the LAN to have access to the USB drive HTTP Disabled by default If you enable this setting you can type http kbserver netgear com products MVBR1210C 1BMCNS asp to access the USB drive HTTP via Internet Disabled by default If you enable this setting remote users can type http kbserver netgear com products MVBR1210C 1BMCNS asp to access the USB drive over the Internet FTP Disabled by default FTP via Internet Disabled by default If you enable this setting remote users can access the USB drive through FTP over the Internet USB Stora
113. ted or received over the WiFi link re Solid blue The WiFi local port is initialized Off The wireless access point is turned off Power Solid green The router is turned on and operating normally O Solid amber POST power on self test is in progress Off Power is not supplied to the router Internet Port Solid green There is an Internet session K Solid amber Traffic meter limit has been reached traffic is blocked Blinking green Data is being transmitted over the Internet connection Blinking amber Traffic meter limit has been reached but traffic is not blocked Blinking green and amber Failover occurred from WAN to mobile broadband Off No Internet connection is detected USB Solid green A USB port has detected a USB device oS Off No link is detected on this port LAN Ports Solid green The local Ethernet ports have detected wired links with computers ry Blinking Data is being transmitted or received Off No link is detected on these ports WAN Port Solid green The Ethernet WAN port has detected an active link Te Blinking Data is being transmitted or received Off No link is detected on these ports Phone Port Solid green The phone is off hook J Off The phone is on hook Message Blinking green Voice mail is waiting Waiting 5 Off There is no unread voice mail DA SMS Message Solid green SMS messages are waiting 2 Off There are no unread SMS messages
114. ternet e No USB Device Attached The router does not detect a USB modem connected to its USB port Either the modem is disconnected or it is not correctly seated To correct the problem remove the modem and reinsert it into the port Received Signal Quality in dBm Modem radio reception A small negative number indicates good signal quality Bytes Transmitted The number of bytes transmitted in the most recent connection session Bytes Received The number of bytes received in the most recent connection session Tx B s The transmission rate Rx B s The receiving rate System Uptime Time elapsed since the last reboot Managing Your Network 67 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Field Description Connection Status Connection Time The time elapsed since the last connection to the Internet through the broadband port Connecting to Server The connection status Negotiation Success or Failed Authentication Success or Failed Getting IP Address The IP address assigned to the WAN port by the ADSL Internet service provider Getting Network Mask The network mask assigned to the WAN port by the ADSL Internet service provider View Attached Devices The Attached Devices screen shows all IP devices that the router discovered on the local network From the main menu under Maintenance select Attached Devices
115. the router near the window or other area of the building Make sure that one of the Signal Quality LEDs is lit indicating that there is mobile broadband coverage with the router e Log in to the router menu and check the Internet configuration Check that the user name password and APN with ISP are set correctly If you use a PIN to connect to the Internet make sure it is entered correctly Troubleshooting 100 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Troubleshoot Access to the Router Main Menu If you are unable to access the router main menu from a computer on your local network check the following If you are using an Ethernet connected computer check the Ethernet connection between the computer and the router as described in the previous section Make sure your computer s IP address is on the same subnet as the router If you are using the recommended addressing scheme your computer s address should be in the range of 192 168 0 2 to 192 168 0 254 Note If your computer s IP address is shown as 169 254 x x Recent versions of Windows and MacOS generate and assign an IP address if the computer cannot reach a DHCP server These autogenerated addresses are in the range of 169 254 x x If your IP address is in this range check the connection from the computer to the router and reboot your computer If your router s IP address was changed and you do not know the current IP address clear the rout
116. the slot on the bottom of your router 2 Place your router near an AC power outlet in a location where you can connect the cables you need for your home network The router needs to be located where you can receive a strong mobile broadband signal while indoors if you are planning to connect to the Internet using mobile broadband Figure 1 Connecting to the Internet 7 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Router Front Panel The router front panel contains control buttons and status LEDs Use the LEDs to verify status and connections WPS WiFi Power Internet USB LAN WAN Phone Voice Mail SMS Message Signal Quality Excellent Signal Quality Good Signal Quality Poor Figure 2 Table 1 describes each LED and button located on the front panel of the router Table 1 LED descriptions LED Activity Description Solid green WiFi has security enabled Blinking green WPS is running Press the WPS button to open a 2 minute window for the router to connect with other WPS enabled devices For more information about this function see Use Push N Connect WPS to Configure Your Wireless Network on page 31 Connecting to the Internet 8 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 1 LED descriptions continued LED Activity Description WiFi Blinking blue Data is being transmit
117. tically when you connect Select Get Dynamically From ISP If you have a fixed or static IP address your ISP has provided you with the required information Select Use Static IP Address and type the IP address subnet mask and gateway IP address in the correct fields For example e IP Address 24 218 156 183 e Subnet Mask 255 255 255 0 e Gateway IP Address 24 218 156 1 Domain Name Server DNS Address The DNS server is used to look up site addresses based on their names e If your ISP gave you one or two DNS addresses select Use These DNS Servers and type the primary and secondary addresses e Otherwise select Get Automatically From ISP Note If you get Address not found errors when you go to a website it is likely that your DNS servers are not set up correctly You should contact your ISP to get DNS server addresses Router MAC Address Your computer s local address is its unique address on your network This is also referred to as the computer s MAC Media Access Control address e Usually select Use Default MAC Address e If your ISP requires MAC authentication then select either Use Computer MAC Address to disguise the router s MAC address with the computer s own MAC address or select Use This MAC Address and manually type the MAC address for a different computer The format for the MAC address is XX XX XX XX XX XX This value might be changed if Use Computer MAC Address is selected
118. times out after a period of inactivity gt To change the time out 1 In the Set Password screen type a number in the Administrator login times out field The suggested default value is 5 minutes 2 Click Apply to save your changes or click Cancel to keep the current period Run Diagnostic Utilities and Reboot the Router The router has a diagnostics feature You can use the Diagnostics screen to perform the following functions from the router Ping an IP address to test connectivity to see if you can reach a remote host If Ping VPN is enabled the ping packet always goes through the VPN if the VPN tunnel is enabled and working Perform a DNS lookup to test if an Internet name resolves to an IP address to verify that the DNS server configuration is working Display the routing table to identify what other routers the router is communicating with Reboot the router to enable new network configurations to take effect or to clear problems with the router s network connection Managing Your Network 71 From the main menu under Maintenance select Diagnostics Click the following buttons to perform the diagnostic tests alent Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Diagnostics Ping Type an IP address Lookup A Domain Name Server DNS Internet Name converts the Internet name such as Ae www netgear com to an IP address If you need the IP address of a server on the Internet you can do a DN
119. tion 00 0c eee eee eae Connect to the Internet oii n 4 bac ed ea Ra Re aH ed Troubleshoot Intemiet Browsing sic ccacendsaciaarecaddeewa reer Troubleshoot a TCP IP Network Using the Ping Utility Test the LAN Path to Your Router 0000 0c cues Test the Path from Your Computer to a Remote Device Problems with Date and Time 2 0 0 0 000 wae ee eee ee ee Restore the Default Configuration and Password 00 Appendix A Supplemental Information Factory Default SeUINGS cccordesecanee bende bene den A ss Technical Specifications 66 ce ce ee eee Appendix B Compliance Notification Index Connecting to the Internet This chapter describes how to configure your Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Internet connection e Hardware Features e Log in to Your Router e Access the Setup Wizard after Installation e Manually Configure Your Internet Settings Note For more information about the topics covered in this manual visit the support website at htto support netgear com Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Hardware Features This section outlines the physical aspects of your Mobile Voice HSPA Broadband 11n Wireless Router Router Stand Since the Mobile Voice HSPA Broadband 11n Wireless Router is a vertical only device use the stand to position your router upright 7 Insert the tabs on the stand into
120. traffic to have a range of priorities depending on the kind of data Time dependent information such as video or audio has a higher priority than normal traffic For WMM to function correctly wireless clients also need to support WMM Turn Internet Access QoS On If you enable QoS the QoS function works to prioritize Internet access traffic Turn Bandwidth Control On To set up the total maximum uplink bandwidth click the Check button to detect current uplink bandwidth that will help you to determinate the maximum bandwidth setting QoS Priority Rule List For the applications that already exist in the drop down list for example On line Gaming Ethernet LAN Port or a specified MAC address see QoS Priority Rule List on page 89 you can modify the priority level by clicking the Edit button or clicking the Delete button to erase the priority rule Otherwise you can also define the priority policy for online gaming an application a LAN port or the computer s MAC address by clicking the Setup QoS Rule button Advanced 88 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C QoS Priority Rule List From the QoS Setup screen click Setup QoS Rule to display the following screen QoS Priority Rule List QoS Policy Priority Description MSN Messenger High MSN Messenger application Yahoo Messenger High Yahoo Messenger application IP Phone Highest IP Phone application Vonage IP Phone Highest
121. uration 1 9 Log in to the router Type http www routerlogin net in the address field of your Internet browser Enter admin for the user name and your password or the default password Under Maintenance on the main menu select Backup Settings Enter the full path to the file on your network or click Browse to locate the file When you have located the cfg file click Restore to upload the file to the router The router reboots Managing Your Network 69 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Erase the Configuration You can use the Erase feature to erase the configuration settings and restore the router to the factory default settings gt To erase the configuration 7 Under Maintenance on the main menu select Backup Settings 2 Click Erase The router reboots After an erase the router password is password the LAN IP address is 192 168 0 1 and the router DHCP client is enabled Note To restore the factory default settings when you do not know the login password or IP address press the Restore Factory Settings button on the bottom of the router for 6 seconds Protect Access to Your Router For security reasons the router has its own user name and password Also after a period of inactivity the router automatically logs itself out The user name and password are not the same as a user name or password you might use to log in to your Internet connection NETGEAR recommends that you c
122. uter MVBR1210C Interference Reduction Table The table below shows the recommended minimum distance between NETGEAR equipment and household appliances to reduce interference in feet and meters Household Appliance Recommended Minimum Distance in feet and meters Microwave ovens 30 feet 9 meters Baby Monitor Analog 20 feet 6 meters Baby Monitor Digital 40 feet 12 meters Cordless phone Analog 20 feet 6 meters Cordless phone Digital 30 feet 9 meters Bluetooth devices 20 feet 6 meters ZigBee 20 feet 6 meters Compliance Notification 113 Index A access 70 protecting 70 restricting by MAC address 26 78 access control 77 administrator login 71 approved USB devices 48 attached devices 68 auto detect connection 14 back panel 10 blocking keywords and sites 57 services 60 broadband settings 15 17 19 C compliance adapters 111 configuration backup 69 connecting USB drive 49 connection mode 14 connection status 67 control buttons 8 D date and time 105 daylight savings time 61 106 denial of service DoS 58 DHCP 12 86 diagnostics 71 disconnecting USB drive 48 DMZ server 84 Dynamic DNS configure 92 E email notification 56 62 Ethernet broadband settings 19 F factory defaults 11 70 file and printer sharing 50 file sharing 41 Firmware Upgrade Assistant 13 flash memory 72 73 front panel 8 99 FTP sharing files us
123. uter s IP address in the Trusted IP Address field and then click Apply You can specify one trusted user which is a computer that will be exempt from blocking and logging Since the trusted user will be identified by an IP address you should configure that computer with a fixed IP address 7 Click Apply to save your settings Content Filtering 59 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Block Services gt To block services 7 Log in to the router as described in Log In to Your Router on page 12 2 Inthe main menu under Content Filtering select Block Services to display this screen Block Services Services Blocking Never O Per Schedule O Always Service Table ld Service Type Port Ip Delete Never is selected by default 3 Select one of the following e Per Schedule Turn on keyword blocking according to the settings in the Schedule screen e Always Turn on keyword blocking all the time independent of the Schedule screen 4 Click Add and the following screen displays Block Services Setup Service Type v Protocol Starting Port 1 865534 Ending Port 1 565534 Service Type User Defined Filter Services For Only This IP Address 192 168 OIP Address Range All IP Addresses Cancel 5 Either select a service from the Service Type drop down list or use the Service Type User Defined field to create a custom service 6 Click Add and the service is listed in t
124. wing LEDs on the front panel e The Phone Port J LED is solid green when the phone is off hook e New voice mail is available when the Message Waiting ft LED is blinking green Table 7 lists the available phone functions Table 7 Phone functions Call features Using your feature Activation code Deactivation code Status code Message Centre Dial 98 to access Answer Transfer number gt Voicemail messages Call Waiting Flash Link or hang 43 43 434 up during call Call Display Blocking Per each outgoing 31 lt 10 digit phone per call call number gt Call Forwarding All 21 lt 10 digit phone 21 21 Calls number gt Call Forwarding No 61 lt 10 digit phone 61 61 36 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C Table 7 Phone functions continued Call features Using your feature Activation code Deactivation code Status code Call Forwarding Busy 67 lt 10 digit phone 67 67 Transfer number gt Call Forwarding 62 lt 10 digit phone 62 62 Unreachable number gt Directory Assistance Dial 411 Emergency Call Dial 911 Client Care Dial 611 Collect Calls Collect calls cannot be received on your Turbo Hub However you can make an outgoing collect call 1 The responses to the status c
125. y the channels allowed in a particular Region or Country Therefore all options described in this user s guide may not be available in your version of the product Europe EU Declaration of Conformity Products bearing the GE marking comply with the following EU directives e EMC Directive 2004 108 EC e Low Voltage Directive 2006 95 EC If this product has telecommunications functionality it also complies with the requirements of the following EU Directive e R amp TTE Directive 1999 5 EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity Intended for indoor use only in all EU member states EFTA states and Switzerland This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed information the end user should contact the national spectrum authority in France FCC Requirements for Operation in the United States FCC Information to User This product does not contain any user serviceable components and is to be used with approved antennas only Any product changes or modifications will invalidate all applicable regulatory certifications and approvals FCC Guidelines for Human Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be i
126. z IP Subnet Mask fess fess ass fo RIP Direction Both za RIP Version Disabled 7 I Use Router as DHCP Server Starting IP Address Ending IP Address Address Reservation IP Address Device Name MAC Address Edit Delete Apply Cancel 2 Change the settings For more information see DHCP Settings on page 86 or Reserved IP Addresses on page 87 3 Click Apply to save the changes Advanced 85 Mobile Voice HSPA Broadband 11n Wireless Router MVBR1210C The LAN TCP IP Setup parameters are explained in the following table Settings Description Device Name LAN TCP IP IP Address The LAN IP address of the router Setup IP Subnet Mask The LAN subnet mask of the router Combined with the IP address the IP subnet mask allows a device to know which other addresses are local to it and which needs to be reached through a gateway or router DHCP Server Use Router as a DHCP This check box is usually selected so that the router functions as a For more Server Dynamic Host Configuration Protocol DHCP server See DHCP information see Settings on page 86 DHCP Settings f on page 86 Starting IP Address Specify the start of the range for the pool of IP addresses in the same subnet as the router Ending IP Address Specify the end of the range for the pool of IP addresses in the same subnet as the router Address Reservation When you specify a reserved IP address

Netgear MVBR1210C User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents