National Instruments VXI-MXI-Express Series User's Manual
Contents
1. Installing Your NI ExpressCard 8360 ExpressCard MXI Interface Complete the following steps to install the ExpressCard interface card 1 Power off your computer ay Note You may want to connect one end of the x1 MXI Express cable to the ExpressCard 8360 prior to installing it into the host computer 2 Insert the ExpressCard 8360 in any available ExpressCard 34 or ExpressCard 54 slot Connecting Cables Connect the x1 MXI Express cable to the VXI MXI Express Series controller and then to the x1 MXI Express host adapter in the host computer Figure 2 shows a system that includes a PCI Express based host computer and a VXI MXI I Express Series controller aE 1 Host Computer 3 VXI MXI Express Series Controller in Slot 0 2 VXI Mainframe 4 Host Cable Figure 2 Host System with VXI MXI Express Series Controller VXI MXI Express Series Installation Guide 6 ni com For information on connecting cables to TRIG CLK PORT A B on the NI VXI 8360T refer to the Connecting The Cables section of Appendix D VXI 8360T Hardware Configuration Settings in the VXI MXI Express Series User Manual Powering Up the MXI Express System Complete the following steps to power up the system 3 Notes All VXI expansion chassis must be fully powered before turning on the host computer otherwise the expansion chassis will not be detected by the host There are no requirements on how VXI MXI Express based expansion cha2. VXI 2 Click the Next button at the Welcome screen to start the installation and accept the license agreement 3 Note Ifyou have a previous version of the NI VXI software installed Setup installs the new version over the previous version VXI MXI Express Series Installation Guide 2 ni com 3 Select the installation features from the Features screen Tip For more information about the NI VXI API refer to Chapter 3 Developing Your Application in the VXI MXI Express Series User Manual 4 Click the Next button After reading the license agreement s confirm your acceptance 5 Click the Next button Confirm that you are ready to install and click Next again to begin the installation 6 Setup now copies the necessary files to your hard drive and creates program icons Completing the Software Installation 3 Review the information in any README files that Setup prompts you to read When the installation process completes reboot the system for the changes to take effect If you backed up the manufacturer and model name files restore them to the TBL subdirectory of your NI VXI directory before running MAX Note Ifyou save and restore the TBL files from an older version of NI VXI the software will use TBL files that do not have the latest updates from National Instruments and may not include recent hardware releases If you added additional manufacturer or model names to your TBL files we recommend merging tho
3. amp play compatible software now and in the future The NI VISA software in this kit is compatible with the WINNT GWINNT framework With NI VISA installed on your computer you can run any VXIplug amp play software that is compatible with this framework This includes instrument drivers and executable soft front panel software included with VXIplug amp play compatible instruments from a variety of vendors Installing the NI VXI and NI VISA Software This section describes how to install the NI VXI and NI VISA software Carefully read these directions along with any messages on the screen before making your selections You can quit the Setup program at any time by clicking the Cancel button UN Caution To keep the manufacturer model name tables or the VME device configuration from a previous installation be sure to back them up before starting Setup They are in the TBL subdirectory of your NI VXI directory usually Program Files National Instruments VXI Setup is an interactive self guiding program that installs the NI VXI and NI VISA software and configures your system to use the software with the VXI MXI Express Complete the following steps to perform the installation 1 Insert the CD When prompted select Install NI VXI from the menu If no menu appears when the CD is inserted a Select Start Run and enter the following text where Xis your CD drive usually D X setup exe b Click the OK button to begin installing NI
4. ea INSTALLATION GUIDE VXI MXI Express Series This document describes how to set up and configure the VXI MXI Express Series controller What You Need to Get Started To set up and use the VXI MXI Express Series controller interface kit you need the following items UO A host computer with an available PCI Express slot running the Windows 2000 or Windows XP operating system A PCI Express or ExpressCard to MXI Express interface card A VXIbus mainframe A VXI MXI Express Series controller A x1 MXI Express cable The National Instruments NI VXI driver software CD DO ODODO This document Installing the Software Use the Setup program that came with your NI VXI NI VISA software to install the entire software package or a software update or to reinstall software in the event that your files were accidentally erased Some of the utilities rely on the LabWindows CVI Run Time Engine This software is installed if necessary during the NI VXI NI VISA installation Depending on the type of installation you choose you may need up to 500 MB of free space on your hard drive to accommodate the NI VXI and NI VISA software 1 Some x16 slots may not work correctly with MXI Express adapters 7 NATIONAL p INSTRUMENTS To be compliant with VXIplug amp play specifications a VXI controller must provide the VISA I O driver library standardized by VXIplug amp play VISA ensures that your controller can run all VXIplug
5. puter from electrical hazards your computer should remain off until you finish installing the NI PCle 8361 NI PCle 8362 2 Open the host computer or remove the top cover to gain access to the host computer PCIe expansion slots VXI MXI Express Series Installation Guide 4 ni com 3 Select any available PCI Express expansion slot aye Note The BIOS or motherboard may not support the NI PClIe 8361 NI PCle 8362 in a slot intended for a graphics card 4 Locate the slot Remove any slot and back panel covers and hardware for example screws 5 Touch the metal part of the power supply case inside the computer to discharge any static electricity that might be on your clothes or body 6 Line up the NI PClIe 8361 NI PClIe 8362 with the slot on the back panel Slowly push down on the top of the NI PCle 8361 NI PClIe 8362 until its card edge connector is resting on the expansion slot receptacle Using slow evenly distributed pressure press the NI PCIe 8361 NI PClIe 8362 straight down until it seats completely in the expansion slot as shown in Figure 1 7 Reinstall the bracket retaining mechanism to secure the NI PCIe 8361 NI PCle 8362 to the back panel rail 8 Replace the computer cover 1 NI PCle 8361 NI PCle 8362 Card 3 PCI Express Slot 2 PCI Express Card Edge Connector Figure 1 Installing the NI PCle 8361 NI PCle 8362 National Instruments Corporation 5 VXI MXI Express Series Installation Guide
6. s purpose Also ensure that no other VXI devices in your system are manually configured for the same logical address as your controller The default shipping configuration is that the card auto detects if it is in Slot 0 To install the VXI MXI Express Series controller in Slot 0 of your VXI chassis complete the following steps 1 Power off the chassis 2 Verify that the backplane connector is intact and that there are no bent or missing pins on the controller 3 Insert the VXI MXI Express Series controller into the chassis in Slot 0 as shown in Figure 2 4 Firmly press the VXI MXI Express Series controller into the mating connectors to ensure the module is fully inserted and seated in the connector 5 Tighten the two ejector handle screws 6 Power on the chassis The VXI system controllers operate certain VXI lines as required for VXI systems Verify that any other VXI devices with system controller capability that are in the same chassis are not configured as system controller Installing Your NI PCle 8361 NI PCle 8362 x1 PCI Express to MXI Express Interface Card To install your NI PCle 8361 NI PCle 8362 x1 PCI Express to MXI Express module complete the following steps 1 Power off your computer but leave it plugged in while installing the NI PClIe 8361 NI PCle 8362 The power cord grounds the chassis and protects it from electrical damage while you install the card Caution To protect both yourself and the com
7. se changes with the latest updates included with this version of NI VXI so that all your devices are properly identified Installing the Hardware A This section summarizes how to install your VXI MXI Express Series controller hardware Caution To guard against electrostatic discharge touch the antistatic plastic packages to a metal part of your computer or chassis before removing the boards from their packages Your computer or chassis should be plugged in but powered off Installing Your VXI MXI Express Series Controller 3 Note Although the VXI MXI Express Series controllers are typically installed in Slot 0 of the VXI chassis they may operate in other slots of the chassis If you choose to install the controller in a slot other than Slot 0 the automatic detection circuitry on the controller will detect the slot and configure the controller appropriately if the J2 jumper is set to Auto detect National Instruments Corporation 3 VXI MXI Express Series Installation Guide UN Cautions Having more than one device configured as system controller can damage the VXI system For VXI systems that include VME devices ensure that the VME devices are not configured in the upper 16 KB starting from 0xC000 of the A16 address space This region is reserved for VXI device configuration registers which are used for initializing configuring and interacting with VXI devices The VXI MXI Express Series controller also uses this region for thi
8. ssis are powered up relative to each other as long as they are all on before the host computer is powered on 1 Power on all of the VXI expansion chassis in any order you choose 2 Power on the host computer Powering Down the MXI Express System Because operating systems and drivers commonly make the assumption that PCI devices will be present in the system from power up to power down it is important not to power off the expansion chassis until after the host PC is powered off Powering off the expansion chassis while the host is still on can cause crashes or hangs The order in which expansion chassis are powered off relative to each other is not important Software Configuration and Verification Complete the following steps to configure the software and verify the configuration 1 Run MAX You must run the Resource Manager Resman every time the chassis or computer power is cycled so that your application can access devices in the VXI chassis You can also configure MAX to run Resman automatically at every computer startup by selecting Tools NI VXI VXI Options from the menu and selecting the appropriate checkbox National Instruments Corporation 7 VXI MXI Express Series Installation Guide 2 You can also use MAX to interactively configure the National Instruments hardware in your system Use the right click help for information about the various configuration options After you finish configuring the system thro
9. ugh MAX verify the configuration through the interactive control utility VISAIC Start Programs National Instruments VISA VISA Interactive Control as described in Chapter 3 Developing Your Application in the VXI MXI Express Series User Manual Note If you are using extenders such as MXI 2 to create a multichassis system you may need to run Resman before configuring some of your devices National Instruments NI ni com and LabVIEW are trademarks of National Instruments Corporation Refer to the Terms of Use section on ni com 1legal for more information about National Instruments trademarks Other product and company names mentioned herein are trademarks or trade names of their respective companies For patents covering National Instruments products refer to the appropriate location Help Patents in your software the patents txt file on your CD or ni com patents 2007 National Instruments Corporation All rights reserved 372449A 01 Dec07
Download Pdf Manuals
Related Search