N-Tron 400 Series User's Manual
Contents
1. IN TRON THE INDUSTRIAL NETWORK COMPANY 400 Series Industrial Ethernet Switches Installation Guide Rev 041008 IN TRON THE INDUSTRIAL NETWORK COMPANY Industrial Ethernet Switch Installation Guide 405TX 405FX SC 405FX ST 405FXE SC YY 405FXE ST YY Where YY 15 40 or 80 Rev 041008 CELLE N TRON 405FX Copyright N TRON Corp 2008 820 S University Blvd Suite 4E Mobile AL 36609 USA All rights reserved Reproduction adaptation or translation without prior written permission from N TRON Corp is prohibited except as allowed under copyright laws Ethernet is a registered trademark of Xerox Corporation All other product names company names logos or other designations mentioned herein are trademarks of their respective owners The information contained in this document is subject to change without notice N TRON Corp makes no watranty of any kind with regard to this material including but not limited to the implied warranties of merchantability or fitness for a particular purpose In no event shall N TRON Corp be liable for any incidental special indirect or consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions in this manual or the information contained herein Warning Do not perform any services on the unit unless qualified to do so Do not substitute unauthorized parts or make unauthorized modifications to the unit2. 4 Verify straight through cabling used between stations 5 Verify crossover cabling used between switches or repeaters non X Port only 6 Verify that cabling is Category 5 for LOOMbit Operation 7 Verify TX is connected to far end RX and vise versa 405FX FXE only SUPPORT Contact N TRON Corp at TEL 251 342 2164 FAX 251 342 6353 Wwww n tron com N TRON_ Support n tron com FCC STATEMENT This product complies with Part 15 of the FCC A Rules Operation is subject to the following conditions 1 This device may not cause harmful Interference 2 This device must accept any interference received including interference that may cause undesired operation Ous FE CE 65SN Rev 041008 13 KEY SPECIFICATIONS Physical Height 2 13 5 41 cm Width 5 00 12 70 cm Depth 3 00 7 62 cm Weight 1 2 lbs 0 6 kg Note can be mounted horizontally or vertically Electrical Input Voltage 10 30 VDC Regulated Input Current 220mA max 24VDC Steady State Inrush Current 14 0Amp 0 9ms max 24VDC Input Ripple Less than 100 mV Input Wire Size 16 28 AWG Environmental Operating Temperature 20 C to 70 C Storage Temperature 40 C to 85 C Operating Humidity 10 to 90 Non Condensing Operating Altitude O to 10 000 ft Network Media 10BaseT gt Cat 3 Cable 100BaseT gt Cat 5 Cable 100BaseFX Multimode 50 62 5 125um Fiber Singlemode 7 10 125um Fiber Fiber Transceiver
3. CHASSIS TO the power source should be limited to 3 meters or less in KNOWN GROUNDING POINT length OOOO As an alternate users can run a drain wire amp lug from any of the Din Rail screws or empty PEM nuts on the enclosure When using an unused PEM nut to connect a ground lug via a machine screw care should be taken to limit the penetration of the outer skin by less than 1 4 in Failure to do so f Eee COLE may cause irreversible damage to the internal components of the switch Lh Note Before applying power to the grounded switch you must use a volt DRAIN WIRE WITH LUGS CONNECTING SWITCH meter to verify there is no voltage difference between the power supply s e oc negative output terminal and the switch chassis grounding point GROUNDING POINT METALLIC DIN RAIL MOUNT If the use of shielded cables is required it 1s generally recommended to only connect the shield at one end to prevent ground loops and interfere with low level signals i e thermocouples RTD etc Cat5e cables manufactured to EIA 568A or 568B specifications are required for use with N Tron Switches METALLIC NONMETALLIC B l SHIELDED PATCH CABLE E STP STP Note Strain relief boots not shown for clarity purposes In the event all Cat5e patch cable distances are small i e All Ethernet devices are located the same local cabinet and or referenced to the same earth ground it is permissible
4. Do not operate the unit with the top cover removed as this could create a shock or fire hazard Do not block the air vents on the sides or the top of the unit Do not operate the equipment in the presence of flammable gasses or fumes Operating electrical equipment in such an environment constitutes a definite safety hazard Rev 041008 Safety Warnings ELECTRICAL SAFETY WARNING Do not disconnect while circuit is live unless area is known to be non hazardous WARNING Disconnect the power cable before removing the enclosure top WARNING Do not operate the unit with the top cover removed WARNING Do not work on equipment or cables during periods of lightning activity WARNING Do not perform any services on the unit unless qualified to do so WARNING Do not block the air vents WARNING Observe proper DC Voltage polarity when installing power input cables Reversing voltage polarity can cause permanent damage to the unit and void the warranty Power must be supplied by an isolating source and a 0 5 A max rated UL recognized fuse must be installed immediately before the unit LASER SAFETY 405FXE Only WARNING CLASS 1 Laser Product Do not stare into the Laser Beam Rev 041008 405FX 405FXE amp 405TX Industrial Ethernet Switches The 405TX and 405FX Unmanaged Industrial Ethernet Switches support high speed layer 2 switching between ports The 405TX is an affordable 5 port unmanaged switch that is capable
5. limited in their application to you When the implied warranties are not allowed to be excluded in their entirety they will be limited to the duration of the applicable written warranty This warranty gives you specific legal rights which may vary depending on local law GOVERNING LAW This Limited Warranty shall be governed by the laws of the State of Alabama U S A Rev 041008 16
6. to use fully shielded cables terminated to chassis ground at both ends in systems void of low level analog signals Rev 041008 11 RJ45 CONNECTOR CRIMP SPECIFICATIONS Please reference the illustration below for your Cat5 cable specifications 0 232 0 005 5 69401 27 CATSe CABLE O 237 40 005 6 024011 3 EIA 568B CATSe CABLE Rev 041008 CONNECTING THE UNIT For 405FX amp 405FXE units remove the dust cap from the fiber optic connectors and connect the fiber optic cables The TX port on the 405FX should be connected to the RX port of the far end station The RX port on the 405FX should be connected to the TX port of the far end station For 10 100 Base TX ports plug a Category 5 twisted pair cable into the RJ45 connector Connect the other end to the far end station Verify that the LNK LED s are ON once the connection has been completed For Switch to Switch or Switch to Repeater connections use the X port and a standard Category 5 cable To connect any other port other than the X Port to another Switch or Repeater use a standard Category 5 crossover cable Warning Creating a port to port connection on the same switch 1 e loop is an illegal operation and will create a broadcast storm which will crash the network TROUBLESHOOTING 1 Make sure the O Power LED is ON 2 Make sure the Error LED remains OFF 3 seconds after initial power up 3 Verify that Link LED s are ON for connected ports
7. Characteristics TX Power Min Max 19dBm l4dBm 15dBm 7dBm 5dBm 0dBm 5dBm 0dBm RX Sensitivity Max 32dBm 34dBm 34dBm 34dBm Wavelength 1310nm 1310nm 1310nm 1550nm Multimode Singlemode Connectors LO 100BaseT 5 five RJ45 UTP Ports 405TX 4 four RJ45 UTP Ports 405FX FXE 100BaseFX SC or ST Duplex Port 405FX FXE Recommended Minimum Wiring Clearance Front 2 5 08 cm 405TX 5 12 7 cm 405FX FXE Side 1 2 54 cm Rev 041008 14 Regulatory Approvals Safety UL 1604 US and Canada Hazardous Locations Class I Zone 2 Group IIC T4A EMI EN55022 Class A FCC Part 15 Class A EMS EN55024 1998 EN61000 4 2 1995 EN61000 4 3 1997 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 GOST R Certified Warranty Effective January 1 2008 all N TRON products carry a 3 year limited warranty from the date of purchase Rev 041008 N TRON Limited Warranty N TRON Corp warrants to the end user that this hardware product will be free from defects in workmanship and materials under normal use and service for the applicable warranty period from the date of purchase from N TRON or its authorized reseller If a product does not operate as warranted during the applicable warranty period N TRON shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the
8. P N 900 PM may be used to securely mount our 100 200 300 400 500 or 900 Series products to a panel or other flat surface Our Rack Mount Assembly P N 900 RM may be used to mount our products to standard 19 racks Rev 041008 FRONT PANEL TT TE TE aaan N TRON 405FX From Left to Right LNK Link LED for Fiber Optic Port 405FX FXE only TX Fiber Optic Transmit Port 405FX FXE Only RX Fiber Optic Receive Port 405FX FXE Only ACT Activity LED for Fiber Optic Port 405FX FXE only X RJ45 Crossover Uplink Port 405TX Only RJ45 Ports Auto sensing 10 100BaseT Connections Red LED indicates controller error Green LED lights when Power is connected NOTE Each RJ45 data port has two LED s located at the top of each connector The left LED indicates LINK status and the right LED indicates ACTIVITY Rev 041008 LED s The table below describes the operating modes Color Description GREEN Power is Applied OFF Power is OFF RED Controller HW Error OFF No Errors Normal Operation GREEN Link between ports established OFF No Link between ports GREEN Data is active between ports OFF Data 1s inactive between ports APPLYING POWER Side View S d En ud ind gt vv Pevi Unscrew amp Remove the DC Voltage Input Plug s from the side header Install the DC Power Cables into the Plug s observing polarity Plug the Voltage Input Plug s back into the side header Tightening tor
9. THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO OPEN REPAIR OR MODIFY THE PRODUCT OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING POWER CUTS OR OUTAGES OTHER HAZARDS OR ACTS OF GOD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW N TRON ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATA OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF N TRON OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT N TRON S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE DISCLAIMER Some countries states or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers or the limitation of liability for personal injury so the above limitations and exclusions may be
10. defective product All products that are replaced will become the property of N TRON Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day watranty or the remainder of the initial warranty period whichever is longer N TRON shall not be responsible for any custom software or firmware configuration information or memory data of customer contained in stored on or integrated with any products returned to N TRON pursuant to any warranty OBTAINING WARRANTY SERVICE Customer must contact N TRON within the applicable warranty period to obtain watranty service authorization Dated proof of purchase from N TRON or its authorized reseller may be required Products returned to N TRON must be pre authorized by N TRON with a Return Material Authorization RMA number marked on the outside of the package and sent prepaid and packaged appropriately for safe shipment Responsibility for loss or damage does not transfer to N TRON until the returned item is received by N TRON The repaired or replaced item will be shipped to the customer at N TRON s expense not later than thirty 30 days after N TRON receives the product N TRON shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to N TRON for repair whether under warranty or not ADVANCE REPLACEMENT OPTION Upon registration this product qualifies
11. for advance replacement A replacement product will be shipped within three 3 days after verification by N TRON that the product is considered defective The shipment of advance replacement products is subject to local legal requirements and may not be available in all locations When an advance replacement is provided and customer fails to return the original product to N TRON within fifteen 15 days after shipment of the replacement N TRON will charge customer for the replacement product at list price WARRANTIES EXCLUSIVE IF AN N TRON PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT N TRON S OPTION TO THE FULL EXTENT ALLOWED BY LAW THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES TERMS OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES TERMS OR CONDITIONS OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE SATISFACTORY QUALITY CORRESPONDENCE WITH DESCRIPTION AND NON INFRINGEMENT ALL OF WHICH ARE EXPRESSLY DISCLAIMED N TRON NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS N TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN
12. n the ProductCD and our web site http n tron com nview zip Once N ViewOPC is installed you should view the Ports Counter page to remotely monitor each connected port You may find it helpful to Copy Alt PrintScreen the Port Counter information for each port and Paste Control V into a Windows document for further review Please consult your N View OPC Server Manual for additional information Rev 041008 DIN Rail Mounting Install the unit in a standard DIN Rail Recess the unit to allow at least 5 of horizontal clearance for fiber optic cable bend radius 2 for TX models Note This unit may be mounted horizontally or vertically To install the unit to 35mm industrial DIN Rail Place the top edge of the included mounting bracket on the back of the unit against the top flange of the DIN Rail at a 15 angle Rotate the bottom of the unit to the back away from you until it snaps into place To remove the unit from the 35mm industrial DIN Rail apply downward force to the unit until it disengages from the bottom of the unit from the DIN Rail Then rotate the unit approximately 15 upward and towards you to completely remove the unit Optional Mounting With the exception of the 524TX and 526FX2 all N Tron products are designed to be mounted on industry standard 35mm DIN Rail However DIN Rail mounting may not be suitable for all applications We offer two alternative mounting solutions Our 900 Panel Mount Assembly
13. of auto negotiating 10 100 Mb and half full duplex communications The N TRON 405TX is housed in a ruggedized steel enclosure and provides 5 Category 5 compliant 10 100 BaseT connections for high performance network design and hub repeater upgrades The 405FX is a 5 port unmanaged switch that has 4 ports identical to the 405TX plus an additional multimode fiber optic up link port capable of 2 Kilometers of 100 Mb communications without the use of repeaters The 405FXE is a 5 port unmanaged switch that is similar to the 405FX but with extended range The N TRON 405FXE utilizes a singlemode fiber transceiver that is capable of 15 Kilometers of 100 Mb communications Both the 405FX and 405FXE utilize the IEEE compliant SC or ST duplex connector for fiber optic communications The 4 10 100Base TX ports utilize the RJ45 shielded connector All N TRON switches come housed in a steel ruggedized Din Rail enclosure designed to withstand the most demanding industrial applications and have been fully tested and certified at industrial environmental extremes Al 405 Units operate on 10 30VDC 0 2A Key Features e Full IEEE 802 3 amp LOOBASE FX Compliance e Extended Environmental Specifications e Support for Full Half Duplex Operation e LED Link Activity Status Indication e Auto Sensing Speed and Flow Control e Upto 1 0 Gb s Maximum Throughput e Industry Standard DIN Rail Enclosure Rev 041008 PACKAGE CONTENTS Please make sure the E
14. que for the terminal block power plug is 0 22 Nm 0 162 Pound Foot All LED s will flash ON Momentarily including the Error LED Verify the Power LED stays ON GREEN Verify the Error LED is OFF after a few seconds Note Only 1 plug is required to be connected to power input for minimal operation For redundant power operation V and V2 plugs must be connected to separate DC Voltage sources Use wire sizes 16 28 gauge Recommended 24V DC Power Supplies similar to LOOVAC 240VAC N Tron s NTPS 24 1 3 DC 24V 1 3A Rev 041008 10 N TRON SWITCH GROUNDING TECHNIQUES The grounding philosophy of any control system is an integral part of the design N Tron switches are designed to be grounded but the user has been given the flexibility to float the switch when required The best noise immunity and emissions i e CE are obtained when the N Tron switch chassis is connected to earth ground via a drain wire Some N Tron switches have metal din rail brackets that can ground the switch if the din rail is grounded In some cases N Tron switches with metal brackets can be supplied with optional plastic brackets if isolation 1s required NONMETALLIC pin raz Both V legs of the power input connector are connected to O chassis internally on the PCB Connecting a drain wire to Todi hen COM earth ground from one of the V terminal plugs as shown here ottano CONNEC E will ground the switch and the chassis The power leads from a SWITCH
15. thernet Switch package contains the following items 1 405FX 405FXE 405TX Ethernet Switch 2 This Installation Guide Contact your carrier if any items are damaged INSTALLATION Read the following warning before beginning the installation WARNING The 405FXE unit contains a Class 1 Laser Do not stare into the laser beam fiber optic connector when installing or operating the product Never install or work on electrical equipment or cabling during periods of lightning activity Disconnect the power cable before removing the enclosure top Do not operate the unit with the top cover removed UNPACKING Remove all the equipment from the packaging and store the packaging in a safe place File any damage claims with the carrier Rev 041008 405FX 405FXE HALF DUPLEX SETUP While all RJ45 ports are Autosensing the 405FX 405FXE Fiber Optic Port is factory configured for full duplex operation In the event half duplex operation is desired follow these steps Remove the Voltage Input Power Plugs Remove the top cover 8 screws Remove the jumper plug JP1 from pins and 2 Replace the top cover Proceed with the installation ee Full Duplex Pins 1 and 2 shorted Half Duplex Remove jumper In order to verify the jumper settings have been set correctly for units which have the N View option turned on you should install N ViewOPC Server software on a PC connected to the LAN The software is freely distributed o
Download Pdf Manuals
Related Search