MURO VISLIDER VL71-FLR User's Manual
Contents
1. loading The stopper block fixing cap screw when loosened too much can cause its head to protrude Pay due attention to it Life size 30 mm Factory setting is for 30mm type 4mm wrench 3Omm Tighten type K My N lLoosen ia Stopper block e Push rightward gt 22 mMm 4mm wrench Stopper block Pull leftward 4 Screw guide position adjustment Carry out the screw guide position adjustment according to the length of the screws used Factory setting is for 45mm screw length 4mm wrench Loosen bY i Adjustment SN Screw length 45 mm Screw length 55 mm Screw length 75 mm CS2845UKT CS2855UKT CS28 75UKT 5 Feeding screws Insert the VISROPE into the feeder block until it stops Push the main body by no less than 30mm and then pull it back When the screw is not fed to the center even after the above step was repeated several times carry out the guide cover adjustment by referring to 6 Adjustment of guide cover and then retry the screw feeding Feeder block It t l E Push the main bady by no less than 30m BO sert the VISROPE fi until it stops Stops before the center O gt P e o gt The screw is fed to the center 6 Adjustment of guide cover Improper guide cover play can affect screw feeding or screw driving Any time the VISROPE was replaced make sure to check the guide cover play and adjust it to the adequate level To adjust the play f2. 122 FAX 81 03 3704 2348 TEL 905 451 7667 FAX 905 451 7936 http www muro com VL71M01U 2002 9 9 Printed in Japan
3. MRO MURO CORPORATION YVL71 FLR V SLIDER Heavy Duty Auto Feeding Screwdriving Tool Instruction manual with warranty card Safety precautions Parts designation Specifications Assembling VISLIDER Loading VISROPE Driving screws Maintenance and inspection Safety precautions N WARNING Denotes risk of personal injury loss of life or damage to the tool In case of nonobservance of the instructions in this manual Before use be sure to carefully read the instructions Read the related Drill instruction manual too Be sure to wear protective goggles during work Be sure to wear a dust proof mask during work Depending on the work environment wear ear protectors hardhat working shoes and other safety gear Be sure to use the specified Adaptor Kit that is dedicated to your Drill model Be sure to use the specified VISROPE connecting screws Ensure solid footing and hold yourself in a safety first position Wear clothes proper for work Keep the workplace in order and well lit When working in an elevated place make sure there is nobody beneath Be very careful not to let this unit and screws fall Never direct this unit toward anybody Never keep your hands feet and head close to the tip screw outlet of the unit during work Keep the unit away from open fire and flame Do not use the unit near volatile flammable substances such as gasoline thinner gas paint and adhesive The unit may catch f
4. he next screw is made ready at the same time When the screw driving is finished the sound and vibrations due to clutch contact will be produced Go on using the tool if there is no problem in screw driving After performing several dozens of VISROPE driving an empty plastic strip comes out long Although the machine is usable even if this strip is untreated cut it with a nipper at a suitable interval lest it should be entangled with the screws outside the magazine and should disturb the operation Press the tool against the surface at the right angle Press the lock button Do not change the angle while driving While keeping the motor running While pulling the trigger 90 degree 5 Removal of VISROPE To remove the VISROPE pull out the VISROPE while the guide cover and the grip finger are open Push the main body 5mm or so to facilitate withdrawal of the VISROPE Open the Pull out grip finger the VISROPE 6 Bit replacement To remove the bit first pick up the bit as much as possible while pulling the sleeve Then while pulling back pressing down the top end pull out the whole bit To mount the bit insert the bit while pulling back pressing down the top end Then while pulling the sleeve insert the bit fully to its position and fix it by returning the sleeve After this make sure that the bit is fixed completely at its position by moving it up and down The bit is c
5. ire or explode Do not use the unit in rain or water splashed wet or humid area Do not leave the unit in rain either Keep the unit accessories and consumable parts without reach of children For after use handling refer to Maintenance and inspection Handle the unit with enough care Dropping or hitting may result in malfunction Keep these instructions in the safe place Parts designation Screw Guide i Dial Grip Finger Guide Cover 3 mm Wrench 4 mm Wrench Magazine Sleeve Main body Feeder Block Magazine Cover Handle Bar A Handle Rod Motor Electric Drill Standard Accessories D 13 mm Spanner Da 7 mm Spanner 6 mm Wrench 7 4 mm Wrench 3 mm Wrench Installed in the magazine Specifications Heavy Duty Auto Feeding Screwdriving Tool Overall length including the handle Approx 885 1 005 mm For 45 mm screw length Weight without the motor Max driving depth Applicable screw length Approx 5 4 kg Approx 8 mm 32 76 mm 1 1 4 to 3 Applicable screw head diameter DIA 10 13 mm Applicable screw nominal diameter DIAS 6 mm Electrical specifications See the motor instruction manual Assembling VISLIDER 1 Assembly and fitting of rod handle Remove the hexagon fitting bolt and the washer from the handle rod To the handle rod fit the handle bar the washer and the hexagon bolt in this order Tighten the hexagon fitting bol
6. irst loosen the hexagon nut using the 7mm spanner and then adjust the cap screw using the 3mm wrench After this tighten the hexagon nut using the 7mm spanner to fix the cap screw Proper play Hexagon nut mm spanner Smm wrench is 1 2mm r Cap screw o gt Suie Cover Q Driving screws 1 Adjustment of rod handle length 2 Adjustment of screw driving depth To adjust the rod handle length loosen the knob Turn the dial to adjust the screw driving depth and press it with force to disengage the inside fixing tab After this adjust the length and tighten the knob to fix Adjust the length Kag f N Lani A A Knob Tighten 3 Direction of bit rotation Direction of bit rotation can be reversed using the motor forward reverse rotation switch Use the forward clockwise rotation to drive tighten the screw and the reverse counterclockwise rotation to loosen remove the screw Refer to the relative instruction manual of the motor on how to operate the forward reverse rotation switch 4 Driving screws First depress the lock button while pulling the trigger of the motor in order to keep the motor running Next hold the handle bar of VL71 FLR and press the tool against the material at the right angle to drive the screw When the screw has been driven completely to the preset depth the clutch sound can be heard Then reduce the pressing force and pull back the handle bar The screw driving is now finished and t
7. onsumable Worn out bit may cause poor tightening or damage the screw head Replace the bit with a new one before it is worn out _Removing the bit Mounting er i a R mi a j l hei i Maintenance and inspection 1 The tool may malfunction if it is used continuously without removing the adhered sawdust plasterboard particles iron powder or dusts Be sure to clean the tool after every use 2 To wipe the unit clean use dry cloth or neutral detergent soaked cloth Do not use gasoline thinner or the like which would damage the unit Never wash the unit in water which would get it rusty or malfunctioning 3 The bit of the specific adaptor kit is consumable If its both heads have worn out immediately replace it with new one Worn out bit may cause poor tightening or damage the screw head Store the unit in a dry cool place Keep it without reach of children Avoid any unstable spot to store the unit on 5 Do not disassemble and repair the unit yourself For repairs contact your dealer VL71 FLR Warranty Card Model VL71 FLR Warranty period 6 month after date of purchase Date of purchase Address Phone Address Name Phone Make sure that the above form is filled out This warranty shall be invalid if the marked information is missing O D t O 3 D om D D D s l If within the warranty period the unit fails due to defect in material or workmanship the manufacturer will repair the uni
8. t free of charge 2 To ask for free repair within the warranty period please take the unit and this warranty card with you to your dealer 3 Even within the warranty period the following cases are not covered by this warranty a Troubles or damages due to wrong handling and use or through tampering with the unit b Troubles or damages due to dropping or rough handling during moving or transport c Troubles or damages due to fire earthquake flood lightning and other natural disasters and pollution d Troubles or damages due to poor storage and negligence in maintenance e Loss or missing of this warranty card h No date of purchase customer s names and address or dealer s name and address entered in this warranty card Or forged document 4 If you want an engineer sent to you for repairing this product you will be charged for his or her travel expenses and labor 5 This warranty card will never be reissued Keep it in a safe place This warranty covers free repairs within the written warranty period and under the condition of proper use This card is not intended to restrict the user s legal rights For repairs after the warranty period contact your dealer or the Customers Services of MURO NORTH AMERICA INC or MURO CORPORATION Manufacturer Please ask to MURO CORPORATION MURO NORTH AMERICA INC 1 4 10 Kaminoge Setagaya ku Tokyo JAPAN 158 0093 7 Tilbury Crt Brampton Ontario CANADA L6T 3T4 TEL 81 03 3703 4
9. t using the 13mm spanner 13mm spanner Hexagon fitting bolt Washer Handle rod 2 Fitting and removal of magazine To fit the magazine insert the magazine holder into the bracket at top end of the main body until it clicks Bracket Magazine Mount the assembled rod handle on the rear of the main body Tighten the two fitting screws using the 6mm wrench screws 6mm wrench To remove the magazine withdraw it while pulling the magazine stopper with fingers g Withdraw Magazine Loading VISROPE 1 Setting VISROPE Open the magazine cover while pulling the Set the VISROPE to the magazine as shown magazine lever below Remove the rubber band from the VISROPE p a Magazine cover Open VISROPE 2 Switching magazine inner lid Lift the inner lid while holding the inner lid stopper on the magazine cover Insert the inner lid until it snaps in the orientation corresponding to the screw length Inner lid stopper Screw length Screw length 45 5 mm 32 43 mm Magazine cover 3 VISROPE types and stopper block adjustment Two types are available in the VISROPE for VL71 FLR 30mm type and 22mm type Depending on the type the position of the guide differs and the stopper block needs to be adjusted to fit for the screws used The first VISROPE has an extended plastic strip as shown below which is needed to drive the first screw Please confirm the presence of this extension when
Download Pdf Manuals
Related Search