Morphy Richards 28023 User's Manual
Contents
1. 5 The LED clock display will fast forward the minutes and hour segments Release the TIME button 2 when your desired time is set 4 The PM indicator 10 will illuminate to indicate 12 00 midday has been reached By holding the hour button down the hour will advance by 5 hours Note In this mode the unit will not be able to receive the automatic MSF signal Setting the alarm 1 time 1 Press the ALARM button 6 once in time mode AL 01 will display As the alarm button is released the previous alarm time will display 2 Repeatedly press the SNOOZE to select the desired type of alarm as follows Type of DAILY WEEKDAY WEEKEND Disabled alarm LED display dY17 dY15 dY67 ole Note The default type of alarm is daily dY17 P4 3 Press the HOUR MSF to adjust the alarm time by 1 hour press and hold HOUR MSF to adjust the alarm clock by 5hrs 0 5 seconds 4 Press the MINUTE button to adjust the alarm time by 1 minute press and hold the MINUTE button to adjust the alarm clock by 5 min 0 5 seconds 5 To exit the alarm setting press the TIME button once or wait for 15 seconds the display will revert back to the time The alarm will activate at the set alarm time The alarm will automatically turn off after 59 minutes Setting the alarm 2 time 1 Press the ALARM button twice in time mode AL 02 will display when alarm is pressed 2 Repeat the same procedure as used for alarm 1 Viewin2. by Morphy Richards Ltd Talbot Road Mexborough S64 8AJ Morphy Richards products are intended for household use only Morphy Richards has a policy of continuous improvement in product quality and design The company therefore reserves the right to change the specification of its models at any time
3. arm settings If the optional battery is not installed in case of the AC power failure when power is restored the clock will go through the automatic msf clock setting You will need to set the alarm Battery back up is designed to operate for a short period only If the unit is not to be used for a prolonged period remove the battery to avoid battery leakage In the interests of environmental safety dispose of batteries safely P3 Illustration ooo oe ef co HOUR MSF MINUTE 11 Location of controls 1 Speaker 7 LED clock display 2 Time button 8 Alarm 1 indicator 3 Hour MSF button 9 Alarm 2 indicator 4 Snooze button 10 PMindicator 5 Minute button 11 Battery compartment 6 Alarm button located underneath unit P2 Switching on and setting the clock time Before you start using your alarm clock you must start by setting the clock to the correct time 1 Place the unit on a flat surface Plug the mains plug into the wall socket and switch on the wall socket Automatic MSF clock setting 2 The LED clock display will count up from 00 to 59 several times and will then set the time automatically using the MSF signal that it receives from the national physical laboratory at Rugby Manual clock setting 3 If you wish to set the time manually press and release the TIME button 2 to change the mode Press and hold theTIME button and simultaneously hold down the HOUR MSF button 3 or the MINUTE button
4. ck will return to time mode out Reviewing the day of the week 1 Press and hold the TIME button for 3 seconds in time mode the current year is displayed 2 Press the SNOOZE button twice to review the day of the week the day will appear on the display dAY1 dAY7 will be displayed which stands for Monday to Sunday respectively The day of the week cannot be changed but it is already set according to the date 3 Press the TIME button to return to time mode If you do not press any buttons for 15 seconds the clock will return to time mode MSF Signal 1 This mode starts when the HOUR MSF has been pressed in time mode 0 0 displays 2 If you want to review the current time when receiving MSF signal press the TIME button 3 Press the HOUR MSF to alternate between MSF on mode and off 4 When the MSF signal is detected the two digit counter will count up steadily from 00 to 59 until the clock is synchronised Note If the two digit counter is not counting up then it is not receiving the MSF signal change the position of the unit for the best reception 5 When the TIME button is pressed or when a valid MSF signal has been received the clock will return to time mode 6 The unit will automatically synchronize at 12 00am and 3 00am everyday To stop the alarm tone Alarm 1 and 2 have individual alarm tones The alarm is programmed to run for 59 minutes 1 To stop the alarm press the ALARM button 6 The alarm will stop an
5. d will operate again 24 hours later 2 To stop the alarm temporarily press the SNOOZE button 4 The alarm will sound again 9 minutes later 3 To switch the alarm setting off press the ALARM button once and release Then press the snooze four times until the display reads Repeat if necessary for alarm 2 Neither indicator 8 or 9 should be illuminated P6 Guarantee Morphy Richards products are manufactured to internationally accepted quality standards In addition to your statutory rights Morphy Richards guarantee your product to be free from manufacturing and component defects for a period of TWO YEARS from date of purchase If your product proves to be defective within 28 days of purchase your Morphy Richards dealer from whom the product was purchased will be pleased to replace it free of charge Should your product develop a defect within the guarantee period but after the replacement period please return the product to the following address together with the proof of purchase brief details of the symptoms and your own name and address Morphy Richards Limited Talbot Road Mexborough South Yorkshire S64 8AJ Your post office will provide a certificate of posting The product will be repaired and returned to you promptly If you need any further advice please call our Helpline UK local rate on 08450 777700 Mon Fri Morphy Richards Website www morphyrichards co uk CE 446 8001 75 Rev2 Imported
6. g the previous alarm type 1 Press the ALARM button to select the setting for alarm 1 or alarm 2 2 Press and hold the SNOOZE button the previous alarm type displays Note Do not press the SNOOZE button again otherwise the type of alarm will be changed 3 Press the TIME button to exit the alarm setting mode The alarm mode will also exit if no buttons are pressed for 15 seconds Reviewing setting the year 1 Press and hold the TIME button for 3 seconds in time mode the current year will be displayed 2 Press the MINUTE button once to change the year in the following sequence 1999 2000 2048 2049 1950 1951 1999 2000 3 Press the HOUR MSF to change the setting by 10 years 4 If an incorrect date is entered after advancing the year by one like Feb 29th 2001 the date will be set to the maximum day of that month which is 28th Feb 2001 automatically 5 Press the TIME button to return to time mode If you do not press any buttons for 15 seconds the clock will return to time mode Reviewing setting the date 1 Press and hold the TIME button for 3 seconds in time mode the current year will be displayed 2 Press the SNOOZE button once for review setting the date mode 3 The date will display in ddmm format P5 Snooze function Once you have activated the snooze the alarm will sound again after 9 minutes 1 Press the SNOOZE button 4 after 9 minutes the alarm buzzer will sound again Maintenance Do
7. morphy richards MSF radio controlled alarm clock 28023 OPERATING INSTRUCTIONS Electrical requirements Check that the voltage on the rating plate of your alarm clock corresponds with your house electricity supply which must be A C Alternating current For alarm clocks with fitted plug If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted IMPORTANT THE PLUG REMOVED FROM THE MAINS LEAD IF SEVERED MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362 fuse must be fitted The socket outlet should be installed near the equipment and shall be easily accessible Battery back up facility unit will work without batteries being fitted Your alarm clock is equipped with a battery back up facility 1 Remove the battery compartment cover located underneath the unit by pushing in the clip and lifting off 2 Insert 3 x AA size 1 5V batteries and connect to terminals Ensure the batteries are inserted correctly 3 Replace the battery compartment cover Batteries not supplied Should a power interruption occur the clock will continue to run however time keeping will not be accurate The display will be extinguished to conserve battery life but the memory will retain details of the clock time and al
8. not expose your clock to extremes of temperature The product should be kept in a warm environment free from dust and damp For external cleaning use only a soft clean damp cloth Use of detergents may damage the finish Technical specification 230v AC 50Hz 4 5V DC type 3 x AA not included AC Power supply Battery back up Warning labels WARNING to reduce the risk of electric shock do not expose this appliance to rain or moisture ATTENTION To reduce the risk of electric shock do CAUTION i RISK OF ELECTRIC SHOCK not remove the cover There are no user DO NOT OPEN serviceable parts inside the unit Refer any servicing to qualified personnel The lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of dangerous voltage inside the unit The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product gt gt To prevent fire or shock hazard do not expose this apparatus to dripping and splashing P7 To advance the day setting by 1 press the HOUR MSF button once To advance the month setting by 1 press the MINUTE button once If an incorrect date is entered after advancing the month like Apr 31st 2001 the date will be set to the maximum day of that month which is Apr 30th 2001 automatically 7 Press the TIME button to return to time mode If you do not press any buttons for 15 seconds the clo
Download Pdf Manuals
Related Search