Mobi Technologies MOBICAM 70062 User's Manual
Contents
1. Internet Kit item 70168 sold separately with such features as motion triggered email or text alerts and time stamped recording to your PC Look for these accessories at your favorite retailer or online at www getmobi com2. 19 Link Code Key 20 DC Power Input 21 Night Light Mode Switch 22 Voice Activation VOX Switch Important Safety Instructions Please read this instruction manual before using your MobiCam Digital Wire less Monitor When using electrical appliances basic safety precautions should always be followed Please keep this information for future reference J N CAUTION This product cannot replace responsible adult supervision e Periodically examine this product for damage to the cord housing or other parts that may result in the risk of fire electric shock or injury Do not operate any product with a damaged cord or plug If your MobiCam Digital System malfunctions or is damaged in any manner return it to an authorized service facility for examination and repair to avoid a hazard e Never use transmitter and receiver near water 1 e bathtub sink etc VAN To prevent electric shock do not immerse in water wipe clean with damp cloth e The AC adaptors are not toys Please keep units out of reach of children A N DANGER To prevent strangulation with power cord never place transmitter within reach of child e Always use transmitter and receiver where there is adequate ventilation To prevent overheating keep away from heat sources such as radiators heat reg isters stoves or other appliances that produce heat e Use only a dry cotton cloth to keep the Camera and Monitor units free of dust Do no
3. or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the affected equipment and the Colour Wire less Monitor e Connect the equipment into an outlet on a main circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help In order to maintain compliance with FCC special shielded cables are used within this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio or TV reception You are advised that changes and modifications made to the equipment without the approval of manufacturer could void your authority to operate this equipment Monitor Features amp Controls Monitor Unit Front 1 2 4 Color LCD Screen 2 Volume Control 3 Brightness Control 4 Power ON LED Indicator 5 LCD and Power ON OFF 6 AV Output 7 DC Power input oe t Monitor Unit Rear 8 Speaker 9 Tilt Screen Release 10 Antenna 11 Channel Selector Scan Mode 11 12 Battery Door 9 12 Camera Features amp Controls Camera Unit Front 13 Night Light 14 IR Night Vision LED s 15 Lens 16 Microphone 17 Light Sensor 18 Power ON OFF with LED Camera Unit Bottom
4. time during the warranty period Mobi Technologies Inc will at its option either replace or repair it without charge After the warranty period a service charge will be applied for replacement of parts or labor for repair To obtain warranty ser vice please return the product to Mobi along with a dated sales receipt from the place of purchase Purchaser is responsible for shipping the product to Mobi Technologies Inc at the address indicated below and for all associ ated freight and insurance cost This warranty does not cover damage caused by accident misuse abuse improper maintenance or unauthorized modifica tion A charge will be made for repair of such damage This warranty ex cludes all incidental or consequential damages and any liability other than what is stated above Mobi Technologies Inc 5913 Blackwelder St Culver City CA 90232 www getmobi com 2009 Mobi Technologies Inc All Rights Reserved Mobi Technologies Inc Please register your product at www getmobi com registerproduct php 13 Expand Your Monitoring Possibilities The available MobiCam Digital Additional Camera 70063 sold separately can be added to your system for a total of 2 or 3 so you can switch between them either automatically or at the touch of a button CAM 3 And you can monitor picture and sound remotely on your computer or other Internet device from any where in the world with the avail able MobiCam
5. Oy Mobi Cam Uk igi ital Wireless Monitoring System Instruction Manual me Table of Contents Package Contents Features FCC Regulation Monitor Features amp Controls Camera Features amp Controls Important Safety Instructions Battery Installation amp Set Up Camera Operation amp Installation Monitor Operation amp Installation Troubleshooting Warranty 12 13 Introduction Congratulations on the purchase of the MobiCam Digital Wireless Video Moni toring System which incorporates the latest in wireless technology We are sure that you will be pleased with the quality and features of this product We recom mend that you read these instructions carefully before use The MobiCam Digital Wireless Video Monitor enables you to transmit picture and sound wirelessly which is ideal for many situations such as monitoring babies young children pets or the elderly It can also be used for household security or as an office or warehouse surveillance system Package Contents e x Camera Unit additional cameras item 70063 sold separately e 1 x Monitor Unit e 2 x AC DC adaptors e x Li ion Rechargeable Batteries e x Instruction Manual e x Troubleshooting guide e 1 x AV cable Note If you find any of the above items are missing or need to order replace ment parts please contact the manufacturer or visit www getmobi com Features DigiLock Wireless with FHSS t
6. e will return with a clear picture whenever the switch is moved to the ON position Channel Selection Mode The monitor allows you to monitor up to 3 cameras additional cameras sold separately Select the desired channel either A B or C 11 Both the Moni tor and Camera will be initially set to channel A Your monitor will display the selected channel at the top left corner of the screen NOTE If the picture continues to switch between cameras the Automatic Chan nel Scan mode is activated Automatic Channel Scan This option allows the Monitor unit to scan through all 3 channels automatically and stops at each channel for about 5 7 seconds Slide the Channel Selector switch 11 to the SCAN position to activate this feature The receiver will automatically skip channels that are not linked to a camera Channel Matching Pairing amp Un pairing This product is designed to allow monitoring different areas with up to 3 cam eras Channel A B or C The Monitor and Camera will be initially set on chan nel A If you need to use another Camera for monitoring you need to pair the new camera with a new Channel on the monitor You can disable this feature by selecting only the camera you want to use by using the Channel Selector 11 To Pair A New Camera e Turn OFF both the Monitor and the NEW Camera Place them not more than 10 feet apart e Turn ON the NEW Camera Press the hidden PAIRING button through the
7. echnology for private and secure noise free performance No installation needed ready to use out of the box Compact design for easy portability Transmission range up to 900 ft outdoors and 450 ft indoors Note Actual range can vary depending on the environment Automatic Night Vision mode with 30 ft range for viewing in total darkness Extra wide camera viewing angle lets you see more of the room Expandable up to 3 cameras with automatic camera scanning option Voice activated picture amp sound VOX with Auto Mute allowing better sleep Audio only mode Audio Video output for connection to TV recorder or optional Internet Kit 8 hr built in rechargeable Lithium Ion battery in monitor Ideal for nursery home or office Built in Night Light on camera unit with automatic or manual modes 2 4 inch high resolution color TFT LCD display LCD screen tilts for versatile viewing FCC Regulation This equipment has been tested and found to comply with the requirements of the FCC These requirements are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio
8. hing Back and Forth NORMAL SOLUTIONS The VOX mode is selected on the camera when there is no noise detected by the camera it stops transmitting to save power To turn off select OFF under the VOX settings switch Unit has not been switched on AC DC adaptor has not been connected Adjust the position of the Camera or Monitor No Battery Power check LED indicator The transmitter may not be transmitting either not powered on or in VOX mode Wrong Channel is selected on Monitor Check if the LCD on off switch Low Power Check the LED indicator Check to make sure units are linked properly Check if transmitter has switched to night vision mode AC DC adaptor has not been connected Non rechargeable battery has been used Only special designed rechargeable batteries can be recharged Please contact the manufac turer if you have any questions Unit has not been switched on AC DC adaptor has not been connected Check to make sure you are making contact with the link button Check to make sure you are selecting the cor rect channel Check to make sure you are not in scan mode To stop this feature use the channel selection switch on the monitor and select the desired channel 12 Limited Warranty Mobi Technologies Inc warrants this product to be free from defects in material and workmanship for a period of ninety 90 days from the date of purchase Should this product prove to be defective at any
9. ion Mode Automatic The infrared night vision mode will switch on automatically during darkness or periods of low light levels In this mode only monochromatic images will be displayed on the monitor Nightlight Mode The camera features a handy glowing nightlight around the front edge To chose the preferred nightlight setting slide the Nightlight Mode Switch 21 on the camera bottom to the desired indicator ON The Nightlight will be turned on and remain on continuously AUTO The Nightlight will be set to turn on automatically whenever the cam era senses low levels of light The Nightlight will automatically turn off when the camera again senses sufficient light in the area OFF The Nightlight will always remain off Note When the nightlight is set to AUTO the automatic Night Vision light level feature determines when the nightlight switchs on and off 8 Monitor Operation amp Installation NOTE For best performance it is recommended to keep units at least 7 8 feet away from other wireless devices Power ON OFF To turn on the monitor unit slide the LCD Power On Off switch 5 located on the right side of the monitor to the ON position LCD Off When the LCD Power On Off switch 5 is set to the center LCD OFF position the unit can be used as an audio only monitor This feature enables the monitor to use less power and remain operational but without using the LCD screen The monitor screen imag
10. recommend that you charge battery for 5 6 hours to fully charge Battery will last approximately 4 4 5 hours when unit is constantly on In VOX mode unit will last approximately 8 10 hours WARNING The monitor of your MobiCam Digital Wireless System has a built in recharging circuit Before plugging in either AC adaptors please make sure only the approved rechargeable Li ion batteries or no batteries are inside the battery compartment Camera Operation amp Installation Power ON OFF To turn ON the camera unit press the ON OFF button located at the front of the camera 18 for about second or until back lighting of the switch is turned on CAMERA MODES Voice Activation Mode VOX Voice Activation VOX mode allows your camera to go to sleep when there is no sound in the room The monitor will automatically turn on when the camera detects noise subject to the preset sound level This feature allows you to con serve battery power NOTE The Monitor will automatically display NoLink VOX on screen if no signal is received from the Camera To Activate slide the VOX switch 22 to the ON position on the Camera When the sound level reaches the preset level within the surrounding area the Camera will begin transmitting the image and sound to the Monitor To Deactivate slide the VOX switch 22 to the OFF position on the Camera The camera will then transmit picture and sound continuously Infrared Night Vis
11. small hole at the bottom of the Camera by using a pin 19 The Night Light will start blinking rapidly to indicate pairing mode 9 e Slide the channel selection switch 11 to select the desired Channel A B C e Press and hold the brightness button marked B 3 and turn the monitor ON 5 simultaneously e The monitor will display the word PAIRED e Turn off both the Camera and Monitor then turn both units back on and the pairing process is completed e Repeat the same process to pair a new camera To Disconnect the Paired Camera e Turn the monitor OFF e Select the Channel Camera you want to de link on the monitor 11 e Press and hold the on the brightness control button 3 and ALSO the on the volume control button 2 while simultaneously turning the unit ON e The LCD will display the word DONE when the units are successfully unpaired e Turn OFF both the camera and the monitor to complete the process Audio Video Output Link The Audio Video Output Link allows you to link the monitor to a TV computer DVR or other video recording device so you can capture video and sound from the camera transmission The A V Output Jack 6 is located on the right side of the monitor Simply connect the supplied AV Connector Cord to the jack and connect the other ends three RCA connectors to the Audio and Video input jacks on your TV VCR or other AV device and select the appropriate input on
12. use a dampened cloth water or liquid cleaner of any kind 6 e Remove the battery from the Monitor during long periods of non use e Unplug the AC adaptors from the Monitor and Camera during periods of non use To disconnect from the power supply grip the transformer and pull from the power socket Never pull by the cord e Replace battery with the same equivalent type Please dispose of old defective batteries in an environmentally friendly manner in accordance with the rel evant legislation e Only use the Monitoring System with the supplied power adaptors Battery Installation amp Setup The MobiCam Digital Wireless Monitor is designed to be powered by either batteries or the provided AC DC adaptor Reconnect the monitor to the adaptor whenever possible to maintain battery life The LED power indicator 4 on the monitor will be illuminated when the monitor is turned on Note We recommend that you charge the Monitor for at least 8 hours before operating your Color Wireless Monitor Using AC DC Adaptor e Check that only the approved Li ion rechargeable battery is installed in the monitor e Plug the connector of the AC adaptor to the socket on the unit 7 amp 20 e Plug the adaptor into a household electrical socket e Switch on the power switch of the unit Battery Charge Remaining when not connected to a charger e GREEN fully charged 4 e AMBER low battery recharge for continuous operation 4 We
13. your device The monitor screen will automatically turn off once you plug in the AV cord to the monitor Please refer to your device manual for input selection amp operation Tilt Screen The monitor screen can be set at an angle for improved viewing To angle the monitor press the release button 9 located on the base of the monitor and gen tly lift the screen forward to the desired angle DO NOT force the screen as this may cause the screen to be damaged The screen does not move beyond 90 NOTE Do not press directly on the LCD screen To close gently push the framed edge of the screen until it latches Only when latched will the release button pop the screen out in order to angle it further from there 10 Brightness Control amp Volume Control The brightness control of the LCD can be adjusted by pressing the Brightness Control Button B located on the front of the Monitor 3 Press the to increase and to decrease the brightness of the LCD The volume control of the LCD can be adjusted by pressing the Volume Control Button V located on the front of the Monitor 2 Press the to increase and to decrease the volume on your monitor 11 Troubleshooting PROBLEM Screen turns on and off No reception at Monitor No picture display but can hear sound Only Black amp White picture displayed Batteries cannot be recharged Camera will not link Channels Keep Switc
Download Pdf Manuals
Related Search