Mobi Technologies 70061 User's Manual
Contents
1. Ds 17 Channel Selection Switch 18 Voice Activation Action Selection Switch 19 Analog Audio Video Input Jack 20 Light Sensor for Automatic Night Vision 21 Power On Off Switch 22 Power On Off Indicator 23 Jack 24 25 Child Safe Battery Door Screw 26 Battery Door SAFETY TIPS For proper setup and use please read all instructions Please keep this manual for future reference e This Product is not intended be used as a medical monitor and its use should not replace adult supervision CAUTION This product cannot replace responsible adult supervision e Periodically examine this product for damage to the cord housing or other parts that may result in the risk of fire electric shock or injury Never use transmitter and receiver near water i e bathtub sink etc e The AC adaptor is not a toy WARNING To prevent strangulation with power cord never place transmitter within reach of child Always use transmitter and receiver where there is adequate ventilation To prevent overheating keep away from heat sources such as radiators heat registers stoves or other ances that produce heat e Always remember that you are using public airways when using your monitor e Use only a dry cotton cloth to keep the Camera and Monitor units free of dust Do not use a dampened cloth water or liquid cleaner of any kind DANGER To prevent electr2. Model 70061 Wireless Audio Video Monitoring System Additional Camera LUSER S MANUAL TABLE OF CONTENTS INTRODUCTION PACKAGE CONTENT FEATURES amp COMPONENTS SAFETY TIPS INSTALLATION amp SET UP CAMERA OPERATION amp INSTALLATION POWER ON OFF CHANNEL SELECTION VOICE ACTIVATION VOX AUTOMATIC INFRARED NIGIT VISION PROBLEMS amp SOLUTIONS FCC REGULATION LIMITED WARRANTY ON NN NN OO BW DN INTRODUCTION Thank you for purchasing the Additional Camera for the Mobi Cam AV Wireless Audio Video Monitoring System The 900 MHz MobiCam AV incorporates the latest in advanced technology enabling you to transmit picture and sound wirelessly We highly recommend you read the entire Instruction Manual before use PACKAGE CONTENTS Please note the package should include the following a 1 x Camera Unit b 1x AC Adaptor Instruction Manual MONITOR UNIT FEATURES amp COMPONENTS Monitor sold separately but shown as reference 1 TFT LCD Display 2 Channel Indicator LEDs 3 Channel Selection Switch 4 Speaker 5 Automatic Channel Scan Indicator 6 Power On Off Indicator 7 Power On Off Switch amp Volume Control 8 LCD On Off Switch 9 DC Jack 10 Belt Clip 11 Brightness Controls 12 Battery Door 13 Audio Video Output 14 Child Safe Battery Door Screw CAMERA UNIT FEATURES amp COMPONENTS 15 Camera Lens 16 Channel Indicator LE
3. e made for repair of such damage This warranty excludes all incidental or consequential damages and any liability other than what is stated above Mobi Technologies Inc 5913 Blackwelder St Culver City CA 90232 Toll Free Number 877 662 4462 www getmobi com Mobi and MobiCam are registered trademarks of Mobi Technologies Inc 2009 Mobi Technologies Inc All Rights Reserved 10
4. eiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation with non approved equipment or unshielded cables is likely to result in interference to radio or TV reception The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment LIMITED WARRANTY Mobi Technologies Inc warrants this product to be free from defects in material and workmanship for a period of ninety 90 days from the date of purchase Should this product prove to be defective at any time during the warranty period Mobi Tech nologies Inc will at its option either replace or repair it without charge After the warranty period a service charge will be applied for replacement of parts or labor for repair To obtain warranty service please return the product to Mobi along with a dated sales receipt from the place of purchase Purchaser is responsible for shipping the product to Mobi Technologies Inc at the address indicated below and for all associated freight and insurance cost This warranty does not cover damage caused by accident misuse abuse improper maintenance unauthorized modification or connection to an improper power supply A charge will b
5. ic shock do not immerse in water wipe clean with damp cloth Always remove batteries from the Camera and Monitor unplug the AC adaptors from wall outlets during long periods of non use e Replace only with the same or equivalent type Please dispose of old defective batteries in an environmentally friendly manner in accordance with the relevant legislation INSTALLATION amp SET UP Installing Batteries Your MobiCam AV can be powered by either using the supplied AC power adaptors or batteries Using Batteries a Remove the battery door 12 26 at the bottom back of each unit by loosening the child safe screw 14 25 and sliding the cover downward to release b Both units use 1 5 volt AA size batteries Always use batteries of the same brand and age alkaline recommended Insert 4 AA batteries into the camera and 6 AA batteries into the monitor c Replace the covers by aligning the tabs with the tab holes and tightening the child safe screws CAUTION Remove batteries immediately once they run out of power and dispose of them properly Do not use batteries while using the AC adaptor for extended periods of time as this might cause battery leakage Using AC Adaptors a Insert the AC adaptor into the DC Jack 9 23 of either unit The AC adaptors are the same for both the Camera and Monitor b Plug the AC adaptor plug into a standard AC power outlet CAMERA amp INSTALLATION Po
6. ignal Unit does not turn on Solution e Battery Levels check Led indicator Full Power Green Low Power Orange e The camera may not be set to Camera Mode e Wrong Channel Please note the monitor will return to Channel A automatically after power off e Camera has switched to Infrared Night Version mode e Check to see if the scanning feature is enabled e Check to see if Camera is in VOX mode Make sure both cameras not the same channel Each camera should be set to its own channel to ensure your unit is monitoring two rooms e AC Adapter has not been connected e Unit has not been switched e AC Adapter is plugged into AV jack Make sure to connect the power plug to the DC jack FCC REGULATION These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio commu nications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the rec
7. wer ON OFF Use the Power ON OFF sliding switch to turn ON OFF the unit see 21 on page 3 Channel Selection Press the Channel Selection Switch fig 17 on the Camera to choose which channel you want the unit to transmit on The chan nel indicator LED fig 16 will illuminate which channel the Camera is set to A or B Make sure to set the additional camera to a differ ent channel than the first camera For instance if the fist Camera is set to Channel A then the additional should be set to Channel B Voice Activation To Activate Select the VOX setting on the Function Activation Switch 18 on the left side of the Camera unit When the sound level within the area surrounding the unit reaches a preset level the Camera will begin transmitting the image and sound to the Monitor NOTE The LCD on the Monitor unit will automatically switch to standby mode if no signal is received from the Camera To Deacti vate Select the CAMERA setting on the Function Activation Switch of your camera Automatic Infra Red Night Vision The infra red night vision feature will switch on automatically during darkness or periods of very low levels of light and a black and white image will be displayed on the monitor Once the feature is activated objects must be within 6 ft 2 m of the camera to be seen on the monitor 7 PROBLEMS amp SOLUTIONS Problem Poor reception Only Black amp White picture displayed Units Continually Loses S
Download Pdf Manuals
Related Search