Miele HG01 User's Manual
Contents
1. Installation Permanent Connection Hard Wiring For hard wiring the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher behind the toekick and service panel Pass the permanent power supply cable through the strain relief and secure it to the terminal box Connect L1 Black to L on terminal block N White to N on terminal block GRND To ground connector GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circult conductors and connected to the equipment grounding terminal or lead on the appliance Use copper conductors only Hardwiring the dishwasher should only be done if required by local electrical codes and then in accordance with those codes Do not cut the plug off the power supply cord and connect it directly to the house wiring 31 Installation 12 Test the unit Once the dishwasher is level and secured it should be tested m Remove all packing and literature from inside the unit The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dishwasher If not removed the key could become lodged in the circulation pump m Make sure the triple filter system in the base of the wash cabinet is locked in place Turn the handle clockwise to lock m Close the soap dispenser Do not add de2. Recommended temperature 120 F 49 C max 140 F 60 C Water pressure Must be between 5 145 psi 0 3 10 bar If the water pressure is too low the Intake Drain or Intake indicator may flash see Operating Instructions Frequently asked questions If the water pressure is too high a pressure reducer must be installed 26 New plumbing The water inlet hose comes equipped with a female hose thread con nector This can be directly connected to a shut off valve with MHT male hose thread ends Preferred Installation The hose assembly should be installed vertically so the hose exits from the bottom of the valve box not as shown If this is not possible it can be installed horizontally provided the hose exit remains beneath the main body of the valve box see illustration The valve box should also be installed so that it is at least 10 24 cm above the floor or base of the cabinet so that the excess coiled hose will remain lower than the valve box at all points Existing plumbing If the standard copper plumbing for a dishwasher already exists with a compression fitting and valve as pictured PCC OE m Cut the copper tubing after the valve m Install the compression to MHT Male Hose Thread adapter Supplied with the machine as illustrated m For any other size plumbing buy the correct size adapter from a hardware
3. small arrow Product and Cut out Dimensions G 600 Series Dishwashers Full size models G 643 G 663 Co D CO N l on LO N o z _ oO a oO Se al 323 46 34 8 gt Removing the leg extensions The black leg extensions can be removed to reduce the machine height to 32 33 819 838 mm see Inset A Black leg extension removable B White leg must be installed on machine m After removing the black leg extensions screw the white legs onto the dishwasher Machine heights of 33 34 845 864 mm are not possible using the supplied legs For this height range or for heights greater than 34 886 mm extended legs part 02 702 601 are necessary Contact the Miele Technical Service Department for the appropriate legs Product and Cut out Dimensions G 800 Series Dishwashers Full size models G 843 G 863 10 3215 4 6 35 i o l on NR N a3 N l vt D a a au NS Lo _l oN N Machine heights of 35 37 889 940 mm cannot be obtained using the supplied legs For this height range or for heights greater than 35 889 mm extended legs part 02 702 601 are necessary Contact the Miele Technical Service Department for the appropriate legs Installation 1 Install the steam deflector If the counter is made of different materials the steam deflector should be positioned so it cove
4. be located in the center of the panel at a height that will match the surrounding drawer handles Any screws used to attach the door handle must be countersunk so that the rear of the front panel remains flat Installation Attach the front panel to the dishwasher m Open the door 2 4 5 10 cm The T shaped hanger behind the door handle should fit easily into its respective hole m Place the lower mounting clips into the slots of the dishwasher door as Shown in the illustration m Seat the U shaped slots of the upper bracket onto their respective locator pins m Press the panel against the door and slide down so that all the brackets catch 21 Installation 7 Adjust and secure the front m Once this side of the panel lines up panel with the cabinets secure it by tightening the upper screw on the Once installed the panel can be raised edge of the dishwasher door or lowered up to 14e 2 mm to match the cabinet lines m Repeat the process with the other side of the panel m Close the door m Check the alignment Readjust if needed m Insert the supplied end caps into the four screw holes Adjust one side of the door panel at a time using a T20 Torx screwdriver Do not use a power screwdriver to adjust or secure the decorative panel to the dishwasher m f the upper screws on the edge of the door are not loose loosen them slightly m Ihe panel can be raised or lowered b
5. electrical connection 0 0 0 ee 30 U2 d ee hee oe ee oe eae hee nee cac es 32 os JINGla Te TOCKICK 4 da oaounheeeonebueaeseatenn 3a IMPORTANT SAFETY INSTRUCTIONS Installation Installation maintenance and repair work should be by a Miele authorized service technician Work by unqualified persons could be a hazard and may void the warranty This equipment is not designed for maritime use or for use in mobile installations such as caravans or aircraft However under certain conditions it may be possible for an installation in these applications Please contact the nearest Miele dealer or the Miele Technical Service Department with specific requirements Inspect the dishwasher for transport damage Do not install or use a damaged unit Contact the place of purchase This dishwasher must be installed under a continuous countertop secured to adjacent cabinetry Do not install this dishwasher beneath a cooking surface or oven Do not under any circumstances cut the intake hose or submerge in liquid This hose contains electrical components that could cause injury or property damage if cut or submerged If there is any doubt concerning installation contact the Technical Service Department USA 1 800 999 1360 techserv mieleusa com CDN 1 800 565 6435 service miele ca During the installation process please be careful of sharp edges that can cause harm IMPORTANT SAFETY INSTRUCTIONS Ele
6. reflector m Remove the black plastic reflector holder and the tape holding it in place from the steam deflector m With the reflector cut out left and frontward align the steam deflector with the front edge of the counter Trace the outline of the reflector onto the underside of the counter with a pencil Note For rounded countertops make the tracing closer to the counter s edge so the optic reflection will be visible m Adhere the double sided sticker to the back of the optic indicator reflector m Remove the backing from the other side of the sticker Installation m Line up the black reflector holder with the tracing and press into place e lt lt m Press the optic indicator reflector into the reflector holder The Extended drying feature can be activated to further protect the counter from condensation See the Operating instructions Additional features 13 Installation 2 Install the mounting brackets To ensure stability this dishwasher should be securely attached to the countertop with the two mounting brackets included m Insert the tab of each bracket into the guide holes on top Stone or marble counterops Do not install these mounting brackets if the counter is made of an extremely hard material The securing screws for the mounting brackets are not suitable for such materials 14 3 Install the slide skis Two slide skis are included and sho
7. the dishwasher before it can be safely operated A single large panel or a two piece panel separated at the drawer line can be used Panel size is determined in the following manner Integrated Dishwasher C E O A A T Panel Height HTC TKH HTC Height to the underside of countertop TKH loe Kick Height Installation Panel Dimensions Width oauan boas as 23 C0 Cm Range of panel height G 800 series OT e80 1 eea unease eons 699 768 mm G 600 series 25 28 7 a a 648 718 mm Thickness At least 18 mm where the mounting bracket is to be screwed in position Maximum panel weight G 800 series 21 Ibs 9 5 kg G 600 series 16 5 Ibs 7 5 kg Installation The door panel is attached to the dishwasher using the mounting bracket that comes secured to the front of the unit To remove the bracket m Open the door 2 4 5 10 cm m Loosen the bracket retaining screw black arrow located on each side of the machine door m Pull the bracket up until the upper section of the bracket disengages from the locator pins then remove the bracket 18 Install the bracket on the rear of the custom door panel m Make sure the dishwasher is level m Measure the distance X between the round hole in the machine outer door panel shown in inset and the lower edge of the adjoining cabinet door m Place the do
8. cabinet and cut off the power cord INSTRUCTIONS IMPORTANTES SUR LA SECURITE Installation L installation et les travaux de r pa ration et d entretien doivent tre ef fectu s par un technicien de service autoris Miele Les travaux effectu s par des personnes non qualifi es pourraient tre dangereux et faire annu ler la garantie Cet quipement n a pas t con u pour usage maritime ou pour les installations mobiles telles que les rou lottes ou les avions Toutefois il peut tre parfois possible de faire l installation de ces applications sous certaines conditions Veuillez contacter le Concessionnaire Miele le plus pr s de chez vous ou le D partement du service technique Miele pour leur don ner vos exigences pr cises Inspecter le lave vaisselle pour voir sila t endommag lors de l exp dition Ne pas installer ou utiliser un appareil endommag Veuillez contacter le point d achat Ce lave vaisselle doit tre install sous un comptoir continu bien fix aux armoires adjacentes Ne pas installer ce lave vaisselle SOUS une surface de cuisson o un four Ne jamais sous aucunes circons tances couper le boyau de prise ou submerger dans un liquide Ce boyau contient des l ments lectri ques qui pourraient causer des blessu res o des d g ts mat riels s ils sont coup s o submerg s Si vous avez des doutes au sujet de l installation contactez le D partement du service t
9. ction or break down grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be inserteded in an appropriate outlet installed and grounded in according to local codes and ordinances WARNING An improper connection of the equipment grounding conductor can result in electric shock Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician If there is any question about the proper electrical connection or grounding of this appliance to the power supply please consult a licensed electrician or call Miele s Technical Service Department USA 1 800 999 1360 CDN 1 800 565 6435 30 Specifications The dishwasher comes equipped with a 4 ft 1 2 m power cord with a molded plug for connection to 120 V 60 Hz 15 A grounded receptacle Rated load 12 5 A 1500 W Voltage 120 VAC Frequency 60 Hz Circuit breaker 15 A Power outlet The power outlet for the appliance must be installed within a cabinet on a wall adjacent to the undercounter space in which the dishwasher is located An opening through the partition between the compartments of 1 3 to 4 cm can be made to allow the plug to pass through
10. ctrical safety Before installation make sure the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system lt is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician The manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective grounding system Before installation or service disconnect the power supply to the work area by manually tripping the circuit breaker unplugging the unit or removing the fuse Do not use an extension cord to connect the unit to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating Child safety Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation If the appliance is removed from its installation and will not be used the door to the wash cabinet should be removed to prevent children from being locked in the machine When discarding an old dishwasher unplug it from the power outlet remove the door to the wash
11. d insert the Caps 24 Installation 9 Adjust the door springs m Open the dishwasher door halfway If the door remains in this position when released the springs are adjusted correctly If the door drops the tension on the springs needs to be increased If it closes on Its own the tension on the springs need to be decreased m 10 adjust the door springs use a 120 Torx or a small slotted screwdriver and turn the screw located behind the door in the upper front strip on the left hand side of the dishwasher Do not use a power screwdriver turn clockwise to Increase the tension turn counterclockwise to decrease the tension Note If the door springs can not be adjusted enough the door falls the custom door panel is too heavy Call your Miele dealer or the Technical service Department for advice on stronger door springs 29 Installation 10 Make the plumbing connections An air gap is built into the water inlet system to prevent potable water from mixing with waste water The dishwasher can heat its own water to the temperatures required by the wash program This allows the option of connecting the machine to either a hot or cold water source m For lowest energy consumption connect the dishwasher to a cold water source m For fastest possible wash times with slightly higher energy consumption connect the dishwasher to a hot water source Hot water supply specifications
12. d snap off the excess otherwise trim the toekick along the line using a Saw m Screw the toekick back onto the brackets with the cut edge at the bottom After installation carefully open the dishwasher door to check that the front panel does not hit the toekick If it does remove the toekick and trim it accordingly 36 3 38 39 When contacting the Technical Service please quote the model and serial number of your appliance Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 Alterations rights reserved MVi60 3304 Miele Limited National Headquarters 55G East Beaver Creek Road Richmond Hill ON L4B 1E5 Phone 800 643 5381 905 707 1171 Fax 905 707 0177 www miele ca info miele ca general enquiries professional miele ca commercial enquiries Mielecare National Service Phone 800 565 6435 905 850 7456 Fax 905 850 6651 service miele ca Tech Service M Nr 05 620 662 01 This bio friendly paper was bleached without the use of chlorine
13. echnique Miele USA 1 800 999 1360 techserv mieleusa com CDN 1 800 565 6435 service miele ca N Durant le processus d installation veuillez faire attention aux rebords coupants qui peuvent blesser INSTRUCTIONS IMPORTANTES SUR LA SECURITE Securite electrique Avant l installation s assurer que la tension et la fr quence num r es sur la plaque signal tique correspon dent la source d lectricit de la r si dence Ces donn es doivent corres pondre afin d viter de vous blesser et d endommager l appareil Consulter un lectricien qualifi si vous avez des doutes Pour garantir la s curit lectrique de cet appareil il doit y avoir conti nuit entre l appareil et un syst me effi cace de mise la terre Ce crit re de s curit doit absolument tre respect Si vous avez des doutes faire v rifier le syst me lectrique de votre maison par un lectricien qualifi Le fabricant ne peut pas tre tenu responsable des dommages caus s par un syst me de mise la terre efficace manquant ou inad quat D brancher le courant de la zone de travail avant l installation en d branchant l appareil retirant le fusible ou en faisant sauter le disjoncteur Ne pas utiliser de rallonge pour brancher l appareil Les rallonges ne garantissent pas la s curit requise pour l appareil par ex danger de sur chauffage S curit des enfants S assurer de disposer de tous les embal
14. eee LEGO Installation instructions Integrated dishwasher To prevent accidents and machine damage read these instructions before installation or use M Nr 05 620 662 Contents IMPORTANT SAFETY INSTRUCTIONS d INSTRUCTIONS IMPORTANTES SUR LA S CURIT J Caring for the environment 0 0 00 00 00 en 7 Disposal of the packing material 22 7 DISCOS sO aol MGC se ee ewe ak a 7 Opening the door a 224 ne a de cd os da tes 8 Opening the door without a panel in place nanana aaa ee 8 Without the mounting bracket in place 8 Product and Cut out Dimensions 9 Installation ee sue SEES DREGE H SSG OURO amende 11 1 Install the steam deflector 11 2 metaline mMmo ning Drack e aeai aaa e er a e e E E a 14 3 Install ihe slide SRI de do or sr duree 14 4 Install the dishwasher under the countertop 16 5 Level the legs 1 ne eee eee ee eens 16 6 Install the custom door panel 17 7 Adjust and secure the front panel 22 8 Secure the dishwasher 23 w PONS 16 door opn SPP a aeae Gee ewe 25 10 Make the plumbing connections 26 11 Make the
15. ith the flange pointing toward the center of the machine m Push the mounting brackets in as far as possible by releasing the tension on the spring clip see illustration 34 m Insert the mounting bracket with the flange pointing toward the outside of the machine m Push the mounting brackets in as far as possible by releasing the tension on the spring clip see illustration The included toekick will fit without modification if the machine is set to its maximum height and the toekick is recessed as far as possible 4 10 cm If the machine height is less than maximum or if the toekick is not recessed 4 10 cm the toekick must be shortened The rear of the toekick has two cutting lines Installation m Screw the toekick onto the installed brackets with the cutting lines towards the top and pull out evenly and slowly until it aligns with the toekick of the adjoining cabinets The toekick can not be pushed back in once it has been extended It must be unscrewed so that the tension on the spring clips can be released The brackets can then be pushed in and the toekick reattached 35 Installation m Carefully open the dishwasher door until it hits the toekick m Using the front lower edge of the door panel as a guide draw a line across the toekick m Unscrew and remove the toekick m f one of the cutting lines is close to the line just drawn score the front of the toekick an
16. lages de plastique sacs etc et de les garder hors de la port des b b s et jeunes enfants Danger de suffocation Si l appareil est retir de son instal lation et que vous ne I utilisez pas vous devez retirer la porte du meuble de lavage pour emp cher les enfants de s enfermer dans l appareil Pour disposer d un ancien lave vaisselle le d brancher de la prise enlever la porte du meuble de la vage et couper le cordon lectrique Disposal of the packing material The cardboard box and packaging protect the appliance during shipping These materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation Caring for the environment Disposal of an old machine Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibilty of recycling these materials Ensure that the appliance presents no danger to children while being stored for disposal Before discarding an old appliance unplug it from the outlet and cut off its power cord and remove any doors to prevent hazards Opening the door Opening the door without a Without the mounting bracket in panel in place place m Gently pull on the upper portion of m Grip the T shaped opening with a the mounting bracket until the door finger and pull the door open latch releases
17. or panel on a flat Surface good side face down being careful not to scratch the surface Make certain that the bottom of the panel is towards you Installation m Using a pencil lightly draw a vertical centerline on the panel See illustration on the next page m Draw a horizontal line X inches up from the bottom edge of the panel For two piece panels Two piece panels should be made so that any joining hardware is flush with the back of the panel Failure to do this may impede proper operation of the dishwasher In certain instances you may be able to use the mounting bracket supplied with the machine to secure both pieces to the dishwasher Consult your cabinet supplier maker for the best method of joining the panels When mounting the two pieces make sure that the desired finished panel height is maintained Installation m Place the bracket on the door panel so the notches cross the previously drawn centerline and the bottom of the bracket lines up with the horizontal X line m Mark and drill pilot holes for the screws using a 35 2 5 mm drill bit m Attach the bracket to the back of the panel using the 14 screws provided The top four pair of holes only need to be secured once per pair 20 m Double check the location of the bracket before mounting the panel to the dishwasher The door handle must be installed on the panel before it is attached to the machine It should
18. rs the edge where the materials are joined Countertops with wood or laminate edging should be tacked through the rear holes of the steam deflector A stainless steel steam deflector is supplied to protect the countertop from steam and condesation when the dishwasher is opened If the countertop is made of Corian granite marble or other solid waterproof material the steam deflector is not required The steam deflector has an indicator m Remove the protective film from the reflector to show when the dishwasher deflector iS running m Squeeze the supplied silicone sealant along the groove of the deflector The left side of the reflector and the optic indicator in the the control panel must line up for the reflector to work 11 Installation m Center the steam deflector in the m Press the optic indicator reflector in opening for the dishwasher and align place with the lower front edge of the countertop Note For rounded countertops it may be necessary to pull the steam deflector closer to the counter s edge so the optic reflector will be visible m Secure the deflector in place using the supplied nails m Wipe of any excess silicone with a solution of liquid dish soap and warm water 12 Stone or marble countertops The steam deflector is not required for countertops made of solid waterproof material But it is needed for determining the correct position of the optic indicator
19. s to pass through Installation m Make certain that there are no rough edges that could damage the power cord or hoses If metal cabinets are used place the supplied rubber grommet around the edge of the opening before passing the cable through m Slide the machine into the opening making sure the electrical cable and hoses can reach their connection points without kinking The left side of the optic indicator reflector and the optic indicator must align The drain hose connection at the rear of the dishwasher can be turned to allow the hose to be angled to the right or left m Exercise care when sliding the dishwasher in or out to prevent damaging the power cord or hoses Installation 5 Level the legs m The rear leveling legs can be m Adjust the front leveling legs by adjusted with a 120 Torx screwdriver pushing on the feet with a slotted by turning the screws at the front of screwdriver the slide skis m Tipping the machine slightly backwards If posssible will make adjusting the front legs easier Make sure the machine is level when adjustments are complete To raise the machine turn clockwise To lower the machine turn counter clockwise Several turns may be needed to set the correct height Do not use a power The dishwasher should be raised screwdriver until it just touches the underside of the countertop 16 6 Install the custom door panel A custom door panel must be installed on
20. store m Connect the inlet hose to the existing valve adapter assembly Installation WARNING Elcetrical Hazard Do not cut the intake hose If the hose is cut the dishwasher will not work There will be a water leak and you could be injured If the hose is too long coil it neatly and place it behind the machine Electrical wiring and components should not come into contact with any plumbing fixtures or hoses 2 Installation Drainage system specifications The machine comes equipped with A 5dft long 1 5 m flexible drain hose with an internal diameter of 22 mm Drain hose extensions can be ordered from Miele s Technical Service Department A built in swivel connector allowing the drain hose to be routed in any direction A built in mechanical non return valve on the discharge side to prevent waste water from flowing back into the dishwasher A built in odor trap on the discharge side to prevent odors from entering the kitchen Maximum drain height 39 1 m Maximum drain hose length 12 ft 3 041 Do not shorten the drain hose Do not connect the drain hose to anything but a genuine Miele hose Other hoses may melt or collapse 28 Connect the supplied drain hose to the drain pipe of the kitchen sink either above the P trap using the clamp provided or to the dishwasher connector of the garbage disposal When connecting the drain hose
21. tergent m Run the dishwasher through the Rinse amp Hold program See the m Check for any leaks odd noises and flashing lit fault indicators on the control panel See the Operating Instructions Frequently asked questions if there is a problem operating instructions for information on operation and program selection 32 13 Install the toekick For installations using a continuous toekick or a cabinet matching toekick Before installing the toekick measurements must be taken to ensure that the toekick will not interfere with the complete opening of the dishwasher door The door panel overhang P and toekick depth of recess R determine the maximum dishwasher toekick height H If H is equal to or less than the toekick height of the adjoining cabinets no interference will exist provided that R is at least 19 mm Installation If the door panel hits the toekick when the dishwasher door is opened the toekick must be cut shorter or recessed deeper Note If a decorative or flush mount toekick is desired and R is less than 3 4 19 mm other modifications such as beveling the top rear edge of the toekick may be necessary It is extremely important that the toekick is removable in case service IS needed 33 Installation For installations using the included plastic toekick G 600 Series dishwasher G 800 Series dishwasher m Insert the mounting bracket w
22. to the garbage disposal make sure to remove the knockout from the connection nipple See the disposal manufacturer s instructions for this procedure Installation Venting the drainage system Additional note If the dishwasher drain hose is since all Miele dishwashers are connected to a floor drain or toa equipped with an odor trap and non drain pipe that is less than 8 20 cm return valve the drain hose can be above the floor the drain must be connected directly to the drain pipe as vented Otherwise the water inside the illustrated dishwasher may siphon out during the If plumbing codes require an external wash program air gap on the discharge side of the dishwasher the following requirements To vent the drain must be met m Open the dishwasher door and No part of the drain hose should be remove the lower basket higher than 39 1 m If installed horizontally the drain hose can be up to 12 ft 3 5 m long If the drain hose is angled upwards in any way it cannot be longer than VS The drain connection should be made as close as possible to the dishwasher The internal diameter or 22 mm of the drain hose should not be reduced at any point m Cut off the vent cap located at the right rear of the triple filter system as illustrated 20 Installation 11 Make the electrical connection GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED In the event of a malfun
23. uld be installed on the feet of the dishwasher before the machine is pushed under the countertop This will allow the machine to slide easier protect the floor and allow adjustment of the rear leveling legs from the front of the unit m First adjust the height of the legs so that the top of the dishwasher is roughly 3 mm below the countertop Tipping the machine slightly to the rear if possible will make adjusting the front legs easier Make sure the machine is level when adjustments are complete m Place the skis with the ratchet at the rear under the dishwasher legs 4 Install the dishwasher under the countertop The dishwasher must be installed so that the water and electricity supplies can be accessed through an adjacent cabinet The supplies must not be located behind the machine WARNING Fire hazard Do not cover or crush the plug of an electric appliance Ensure that the cabinet opening for the dishwasher provides ample space for the plug Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which may cause overheating The floor of the cut out where the dishwasher will be installed should be even in height with the surrounding kitchen floor Plywood can be secured to the floor to make the two areas even m Make a 2 x 4 5 x 10 cm cut out in the side or bottom of the cabinet adjoining the dishwasher This cut out is necessary for connection
24. y turning the lower screw on each side of the dishwasher door To raise the panel turn clockwise To lower the panel turn counterclockwise 22 Installation 8 Secure the dishwasher Make certain that the white rubber seal located at the top outer edge of the dishwasher is tight against the bottom of the countertop Do not drill any additional holes through the wash cabinet If in doubt on how to secure the dishwasher please call Miele s Technical Service Department m Open the dishwasher door If the steam deflector is installed the mounting bracket holes must align with the slots in the steam deflector m Using flat head screws secure the dishwasher to the countertop by screwing through both the mounting bracket and the steam deflector 23 Installation For openings exactly 23 60 cm wide N The side mounting holes should only be used for securing the dishwasher if the opening is exactly 7 23 60 cm wide Use of this method on larger 7 openings can damage the machine Weed OS ie and cause leaks Be careful not to ACCEL screw into an adjacent appliance Vy m Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet m Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings A bushing must be placed over the screw before inserting it into its mounting hole m lighten the screws an
Download Pdf Manuals
Related Search