Miele T1570C User's Manual
Contents
1. The vent duct is blocked Before restarting the program proceed as follows Release the ON OFF button Clean the affected part of the machine Turn on the machine again Reselect the terminated program Press the Start button If the drum door opens again the Miele Service Dept should be contacted drops of the water appear along the upper edge of the drum door This may not be a problem A dual filter system with two seals is used to prevent lint from becoming deposited in the heat exchanger These two seals may occasionally cause condensed water to form on the door Laundry coming into contact with these drops of water will dry within in a few minutes after cleaning the heat exchanger water leaks from the machine Check that the heat exchanger door has been replaced correctly If necessary remove and replace it the interior drum light fails to function see next page you have to open the door in the event of a power failure see next page 19 Problem solving guide The interior drum light fails to func tion The bulb may be defective Replace it as follows Turn off the machine or disconnect it from the power supply m Open the door m Use a 3 4 wrench to unscrew the plastic bulb cover located inside the drum and above the door see illus tration The light bulb must not exceed the maximu2. 85 cm adjustable 82 cm 59 5 cm without lid 56 with lid 60 55 kg 103 5 kg dry laundry 2 85 kW 15 A minimum or 30 A 29 30 31 Miele Limited Canadian Head Office 55G East Beaver Creek Road Richmond Hill Ontario L4B 1E5 Phone 905 707 1171 Fax 905 707 0177 Toll Free 1 800 565 6435 Internet www miele ca E Mail info miele ca general enquiries E Mail service miele ca technical service BC Regional Sales Office 3731 North Fraser Way Unit 200 Burnaby British Columbia V5J 5J2 Phone 604 434 1300 Fax 604 434 1309 All rights reserved 002 4503 This paper is made from 100 chlorine free bleached cellulose and therefore protects the environment
3. or injury will automatically enter the anti to persons read the IMPORT crease cycle for 60 minutes This en ANT SAFETY INSTRUCTIONS tails the drum being rotated at short bef tina thi li intervals in order to reduce the forma AS ES tion of creases m Load the laundry loosely into the Once the laundry has been Cru removed check that the drum is m Duvet covers and pillowcases empty Any items left in the drum should be fastened before drying in could be damaged through over order to prevent small items from roll drying during the next program ing inside of them m Clean the lint filter after each drying cycle to prevent excessive energy consumption longer program times and the risk of fire m he door should always be closed after use Important Check that laundry can not be trapped by the door as this may cause damage to the fabric Before drying check the instructions on the fabric care label The following fabrics should not be dried in a tumble dryer Woollens and wool blends These fabrics tend to become matted and shrink ltems filled with down The fine fabric interior tends to shrink depending on the quality of the item involved Pure linen These items should only be machine dried if specified as suitable by the manufacturer on the textile care label The surface of the fabric may other wise tend to become rough Miele dryers have been designed to dry laundry fre
4. Miele NOVOTRONIC Operations Manual for the T 1570 C Condenser Dryer In order to protect yourself and avoid damage to your machine it is absolutely necessary to read the operating instructions prior to installation and operation M Nr 03 719 540 Contents Guide to the machine a ee eee eee eens 3 IMPORTANT SAFETY INSTRUCTIONS 5 Your contribution to the environment vi OPERATING INSTRUCTIONS Logangihe MaC sat ot aw aiie i ee A 8 Unloading Ihe MaACHING 2 s 5 sai A eae eho ee 8 NOLES ONMIGUNONY Cal Ct osm oars tees okt Bhs ooh aoe Bek oe Et Bele BS 4 BS 9 Program selection acd td baie haw bcos bad ded eh bs bot dane boa ok oie Coe ol 10 rodas ceras Uo Sass eae ete area pod rra ot Gos wae 12 13 USER MAINTENANCE INSTRUCTIONS Emptying the condensed water container 0 0 0 ce ee 14 Cleaning and Dates oe Ce AAA e E E E a 15 ProblenrsoNvng QUISE ssia a id ss ri de 18 ARNES al SSIVICS cae cal Paris Dan amp Baer ees 21 INSTALLATION INSTRUCTIONS Grounding and Electrical CONNECTION 0 0 0 ooo os 22 INStalatlOM da ci y E A eee ee 23 Connecting to an external 0Orall o o ooooooo ooo o o o 26 CU os A O TN A 28 WC ia NALES lt a ana dp E E haat Ati ee AE 29 Guide to the machine 1 Supply cable with plug 2 Condensed water container 3 Drum door 4 Control panel 5 Drain hose for condensed water 6 Four height adjustable legs Guide to the machine P
5. ROGRAM SETTING PROGRAM SEQUENCE PERMANENT E Finish COTTONS Empty out container O On Normal e O Drying T RA ie 1 O Cooling down haan O Anti crease Finish Hand iron e DRYING STAGE REACHED 20 mins warm Aa Machine o Hand gt Normal O 15 mins cool air iron iron MADE IN GERMANY TIMED DRYING Pushbuttons Door This button is used to open the door does not stay pushed in ON GOFF When the machine is turned on the On indicator will light up if the door is closed If the door is open the drum light will be on Buzzer Allows the buzzer to sound as the drum rotates during the anti crease cycle Low temp Lower drying temperatures for deli cate fabrics e g acrylics nylon Start starts the selected program it does not stay pushed in Indicator lamps Empty out container The water container should be emp tied PROGRAM SEQUENCE The program sequence indicator lamps show the current status of the drying program DRYING STAGE REACHED These indicator lamps show which drying stage the program has reached For program stages Nor mal and Extra dry the indicator lamp remains at the Normal posi tion PROGRAM SETTING SELECTOR Set the required program by turning the knob either clockwise or counterclock wise COTTONS PERMANENT PRESS TIMED DRYING ltems can be either dried for 20 minutes incl a cooling down phase or cool ai
6. and iron program Permanent press fabrics tend to crease more as the size of the load increases This is particularly true of very delicate fabrics The load should be reduced to 1 5 kg or if necessary to 1 kg Do not dry new dark colored fabrics together with light colored items as they may discolor Program selection Functional description An electronic sensor system monitors the moisture content of the laundry Once the required degree of dryness is reached cold air then enters the drum to cool the laundry The drying program is then terminated Function of the pushbuttons Low Door as EU T Start MADE IN GERMANY Door This button is used to open the door ON OFF When the machine is turned on the On indicator lamp illuminates when the door is closed When the door is open the drum is illuminated Buzzer When activated the buzzer will sound as the drum rotates during the anti crease cycle 10 Low temp Uses lower drying temperatures for delicate fabrics e g acrylic fibers To gently dry delicate fabrics press this button before starting the cycle Start Starts the selected program PROGRAM SEQUENCE indicator The program sequence indicator lamps show the current status of the drying program DRYING STAGE REACHED indicator This indicator shows which drying stage the program has reached PROGRAM SETTING selector There is a range
7. anent press shirts table cloths bedding etc made of blended woven or knitted fabrics e g cotton synthetic 2 5 kg Hand iron Permanent press shirts table cloths pillowcases etc cotton synthetics which are still to pressed 2 5 kg Special instructions With blended fabrics consisting of wool and synthetics consult the manufacturer s instructions as the wool component may cause the fabric to become matted and shrink This is the program that should be tested according to the EN 61121 A11 Standard TIMED DRYING Type of laundry fabric Max load Special instructions warm Individual items e g This setting will run the full comforters or very small length of time regardless loads if the item Is dry beforehand cool Items which are only to be 5 kg aired 13 USER MAINTENANCE INSTRUCTIONS Emptying the condensed water container Depending on your type of installation the condensed water will either be pumped to a drain or collected in the condensed water container located in the upper left corner of the machine The container should be emptied after each drying program Should the container be full when the tumble dryer is started or if it becomes full during normal operation The Empty out container indicator lamp will light The buzzer will sound The drying program will stop The machine will enter the cool
8. d to dry laundry without static cling How ever should fabric softener be re quired use liquid fabric softener in the wash cycle Clean lint filter mesh monthly by wash ing scrubbing with hot soap and water 19 Do not place items exposed to oils in your dryer Items contaimed with oils may contribute to a chemical reaction that could cause a load to catch fire SAVE THESE INSTRUCTIONS For grounding and electrical connection instructions refer to the electrical connection section This dryer is only intended for residential use Your contribution to the environment Disposal of the packing ma terial The transport and protective packing is mostly manufactured from the following recycled or re useable materials corrugated paper cardboard polystyrene CFC free polyethylene foil transparent untreated wood fiber board Please check local environmental regu lations before disposing of packing ma terials and discarding the appliance Disposal of your old machine Old machines contain materials which can be recycled Please contact your recycling center or scrap merchant and render the machine inoperative as per the Important Safety Instructions before disposing of the appliance OPERATING INSTRUCTIONS Loading the machine Unloading the machine m l the wash is not removed at the end WARNING To reduce the risk of the drying program the machine of fire electric shock
9. e Program Selection section The ON OFF button is depressed The door is properly closed The machine is plugged in and the fuse or circuit breaker has not tripped the laundry is not sufficiently dry The load consisted of dissimilar items size and fabrics select a longer drying program Small loads or individual items may cause the program to terminate prematurely Small loads can be time dried the drying times are too long The lint filter is clogged Clean the lint filter in the door The laundry was not spun in the water for a sufficient time Make sure that the laundry is thoroughly spun before drying the anti crease indicator lamp in the sequence indicator display starts flashing Turn the program selector to finish Turn the machine off and then on again Select a program Press the Start button If the indicator lamp starts flashing again this indicates a fault in the machine Please contact the Miele service Dept 18 Correcting minor faults Problem solving guide What to do if Cause Remedy the drum door opens during the drying cycle The machine has overheated The temperature limiter opened the drum door and caused the machine to turn off automatically Possible reasons for overheating The lint filter in the door is clogged
10. e of static cling without the use of dryer softener sheets or simi lar products The dryer continuously monitors the moisture content of the laundry and automatically shuts off the heat when the selected degree of dry ness is reached Through the use of a cool down period where the machine operates without heat cool static free laundry is the end result Dryer softener sheets perform the same function by depositing a chemical residue on both the clothes and the interior of the dryer Over time this coating may lead to per formance reductions in the dryer If fabric softening is desired it is more convenient economical and beneficial to the clothing if a liquid softener is auto matically dispensed while the clothes are in the washing machine Please see the washing machine operating instructions for directions on how to automatically dis pense a liquid softener Notes on laundry care Notes Knitted fabrics and flannel sheets tend to shrink when washed for the first time and also when dried They should not be overdried Extra dry starched laundry can also be dried in the tumble dryer Permanent press items should be briefly spun in the washing machine be fore drying Items which are prone to creasing should not be dried in the PERMANENT PRESS Normal Pro gram Drip dry shirts made of pure cotton may tend to crease depending on the quality of their finish These items should be dried in a H
11. follow necessary ing the manufacturer s instructions Do not hose down the machine or use abrasive cleaners 15 Cleaning and care Cleaning the heat exchanger m Ihe heat exchanger should be cleaned once or twice a year m Open the door m urn the lever so that it is vertical m Turn both levers on the heat ex changer so that they are vertical 16 Cleaning and care m Pull out the heat exchanger and along the two long sides stand the heat exchanger lengthwise on a towel until it dries Replace the heat exchanger in the reverse order Make certain the heat exchanger is pushed in all the way and that the cover is firmly closed Otherwise water may leak from the machine ie m Clean the heat exchanger at both ends front and back 17 Problem solving guide Electrical appliances should only be repaired by qualified personnel Incor rectly repaired machines may put the user at risk There are however minor problems which can be corrected without contacting the Service Department What to do if 7 the tumble dryer fails to start when turned on Cause Check whether the On indicator lights up If so failure to start may be due to an incorrect program selection procedure If the On indicator lamp does not illuminate check that Remedy Repeat the switch on procedure in the correct sequence as outlined in th
12. if dryer has been set up for external drainage of con densed water Programs COTTONS Type of laundry fabric Max load Special instructions Extra dry Multi layer fabrics mixed 5 kg The Extra dry program load of cotton fabrics should not be selected for e g jeans towels jersey wear items sweatsuits Normal Homogeneous loads of 5 kg Should items still be cotton fabrics e g flannel damp select the Extra items underwear socks dry program Normal Knitted cotton fabrics 5 kg Should items still be particularly suspectible to damp select the Normal shrinkage e g jersey program wear or lightweight cotton fabrics Hand iron Cotton or linen fabrics 5 kg Moisture can be e g linens bedding increased or decreased starched items left damp by using Hand iron 44 for easier ironing or Hand iron A respectively Machine iron Cotton or linen fabrics 5 kg The laundry can be rolled including starched laundry for the rotary iron B865E up to prevent It from drying out until it can be ironed These are the programs that should be tested according to the EN 61121 A11 Standard 12 Programs PERMANENT PRESS Permanent press items Normal Type of laundry fabric made of synthetic or blended fabrics e g pullovers dresses pants etc which are not dried adequately in the Normal program Max load 2 5 kg Normal Perm
13. ing down cycle To empty the container m Pull out the container with both hands 14 m Hold the cap open while emptying the container m When the container is empty push it into its recess until it clicks into place Do not drink the condensed water Note The water collected in the container has been distilled by evaporation and can be used in a steam iron or humidi fier for example The following points should be remembered m AS a precautionary measure the water should be passed through a fine sieve or coffee filter in order to strain out any small particles of lint which might otherwise cause dam age Cleaning and care Cleaning the lint filters The lint is collected by the lint filter in the door Clean the filter after every program m Dry the filters before putting them back in place if they were rinsed Before cleaning the tumble dryer disconnect the machine from the m Grip the filter by the recessed power supply handle and pull up to remove Any remaining lint in the hollow part Cleaning the dryer of the door can be removed through y The dryer can be cleaned using the gap at the bottom soapy water or a mild non abrasive detergent not scouring powder and dried with a soft cloth m Remove any accumulated lint from the filters in the door opening l l m he drum may be cleaned using a All filters can be rinsed with water if suitable stainless steel cleaner
14. k Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician 22 Electrical connection This installation should be done by an experienced and qualified person in most cases a licensed electrician in ac cordance with local codes and regula tions This dryer is supplied with a 1 5 m power cord with a 3 pole 4 wire grounding plug 14 30P regular Canadian dryer plug This plug has to be plugged into a 3 pole 4 wire grounding receptacle 14 30R regular Canadian dryer receptacle The receptacle has to be connected to Line 1 Line 2 Neutral and Ground wires The voltage is 120 240 V AC or 120 208 V AC EASY INSTALLATION KIT If you do not have a designated line 4 wire 120 240 V 15 or 30 Amps for this appliance but you have the 4 wire 120 208 240 V 30 Amp Canadian dryer wall receptacle 14 30 R you can use the Miele Double Receptacle Box This consists of two standard recep tacles 14 30 R 4 fuses box and plug cord which allows you to use that single dryer wall receptacle to supply power to a Miele washer and Miele dryer Both machines may operate at the same time because each uses maximum about 15 A current For more information on the electrical connection on the Miele Double Recep tacle Box p
15. lease contact your Miele dealer the nearest Miele Service Depart ment Installation The grill below the drum door should never be blocked as this will prevent a sufficient intake of cold air Where to install the machine Installation It is possible to install this appliance under a continuous countertop The ma chine lid can be removed if necessary The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation n appropriate The machine should be perfectly level stacking kit to match your washing to ensure safe and proper operation machine is required Minor discrepancies do not however have an adverse effect on operation These items are available from the Miele Parts Dept m Ihe machine can be leveled by turn ing the legs clockwise or counter clocwise as necessary m Turn the counternuts up and tighten against the bottom 23 Installation Changing the decor panel Note The door should be closed when installing the decor panel m On the door lock side remove the 4 screws 3 on the side and 1 under neath and the door strip m Loosen the remaining 7 screws on the lower and side decor strips until the decor panel can be bowed slightly and taken out m Reassemble in the reverse order and tighten the screws 24 Decor panel dimensions Values in bracket demote tolerances in mm Width 587 mm 1 Height 602 mm 1 5 Thick
16. m wattage quoted on the data plate m Replace the bulb and the plastic cover The cover must be correctly installed and tightened otherwise moisture may seep in and cause the socket to cor rode 20 This is a temperature resistant bulb and should only be ordered from your Miele Service Dept To open the door in the event of a power failure m Pull forward on the un hinged side of the door After sales service In the event of problems which cannot be solved please contact Your Miele Dealer The nearest Miele Service Depart ment see back cover for the adress When contacting the Service Depart ment please quote the Model and Se rial numbers of your appliance both of which can be found on the right side after the door is opened Specimen Miele vaDe in GERMANY 21 INSTALLATION INSTRUCTIONS Grounding and Electrical connection Grounding instructions This appliance must be grounded In the event of a malfunction ground ing will reduce the risk of electric shock by providing a path of least resistance for the electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and or dinances Warning Improper connection of the equip ment grounding conductor can re sult in a risk of electric shoc
17. ness 1 mm 0 5 Panels which are thicker than 1 5 mm require a 4 mm adapter strip available from Miele specialist dealers or the Miele Spares Dept Note When using the adapter strip the height of the panel should not exceed 596 5 mm 1 5 Installation Fitting a toekick panel The appliance toekick below the door can be concealed using a toekick panel The height and depth of the appliance toekick cannot be altered A cut out must be made in the toekick panel around the ventilation slots as otherwise the airflow to the appliance will be blocked and the machine will nat dry efficiently 25 Installation Connecting to an external drain The condensed water can be drained directly if the machine is installed near a sink or drain outlet The machine is equipped with a non re turn valve as standard to prevent water from flowing back into the machine eg if the machine is connected to a siphon Max drain hose length 3 0 m 10 ft Max drain height 1 0 m 4 ft Accessories supplied 2 m 6 ft drain hose Hose clamp Hose elbow m Loosen the hose clamp from the drain outlet at the lower left rear of the machine and remove the rubber plug m Remove the clamp from the plug and place it over the drain hose 26 Push the drain hose onto the drain outlet Make sure that the hose Is firmly secured by the hose clamp and not kinked Installation m Close the water inlet po
18. of settings for both Cottons and Permanent Press In addition items can be either dried for 20 minutes incl a cooling down phase lasting 8 mins or fluffed in a cool air cycle for 15 minutes To select a program m A program can only be selected when the machine is turned on m Set the desired program by turning the program selector either clock wise or counterclockwise m Press the Start button The program status will be stored for 30 minutes in the event of a power failure The program is cancelled if There is a power failure lasting more than 30 minutes The program has already reached the Cooling down or Anti crease stage Program selection To change a program during drying m Set the program selector to the desired program The new program will start from the be ginning The tables following on the next two pages list the range of applications for the different programs Correct procedure O Press the On Off button O Press the Door button and load the drum Close the door with a firm swing do not push it shut O Select Low temp and Buzzer if so desired O Select a program O Press the Start button After the program has finished O Set the program selector to Finish O Remove the laundry Clean the lint filter O Turn off the machine O Empty the condensed water con tainer Omit this step
19. or explosive substances They give off vapors that could ignite or explode 9 Do not allow children to play on or in the appliance Close supervision of children is necessary when the ap pliance is used near children 10 Always close the door after use to prevent children from leaning on the door and causing the dryer to tilt 11 Do not drink the condensed water 12 Keep the area around the air intake toekick and Surrounding areas free from lint dust and dirt IMPORTANT SAFETY INSTRUCTIONS 13 The interior of the machine should be cleaned periodically by qualified per sonnel 14 Do not reach into the dryer if the drum is moving 15 Do not tamper with the controls 16 Do not repair or replace any part of the appliance or attempt any servic ing unless specifically recom mended in this operations manual Repairs to electrical appliances should only carried out by qualified personnel Incorrectly repaired machines may pose a considerable risk to the user 17 Lint is principally the result of friction caused by items being worn and washed Machine drying causes insignificant amounts of lint to form and as has been established by research in stitutes has no detrimental effect on the lifetime of fabrics 18 Warning Do not use fabric sof tener anti static dryer sheets Residues from these products block up clog the lint filter causing prema ture failure of the dryer Miele dryers are designe
20. r fluffed in for 15 minutes IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using your appliance follow basic precautions including the follow Ing 1 For your own safety and for the pro tection of your machine read these operating instructions carefully be fore using your dryer for the first time Remember to remove the door when disposing of an old machine to pre vent children from accidently locking themselves in Do not install or store this appliance where it will be exposed to the weather Do not install your dryer in rooms where freezing temperatures may occur The reliability of the electronic control system may be impaired This machine should only be used for drying the following fabrics ltems which can be machine dried as specified by the laundry care label ltems which have been washed in water 6 The following fabrics pose a fire ha Zard Items which contain foam rubber rubber or rubberlike components ltems which have been treated with flammable cleaning agents such as gasoline or dry cleaning solvents ltems containing hair lacquer hair spray nail polish remover or similar substances 7 Clean the lint filter before and after each load 8 Do not dry articles that have been previously cleaned washed soaked in or Spotted with gasoline dry cleaning solvents or other flamm able
21. rt above the condensed water container with the bottom part of the rubber plug The plug must face towards the interior of the machine so that the con densed water container can easily be inserted m Attach the elbow to the hose and se cure it to the sink or drain pipe If room is available it can be inserted into the stamp pipe used by the washing machine The water will now be drained automati cally and the container will not need to be emptied 21 Consumption data load Final spin speed Electrical Drying time incl in washer consumption cooling down time kg rom kwh mins Cottons Extra dry 5 1200 3 44 87 1400 3 28 83 1550 Slit 81 Normal 5 1200 3 17 81 1400 3 02 77 1550 2 91 75 Normal 5 800 3 60 92 1200 2 82 74 1400 2 68 71 1550 2 58 69 Hand iron 5 800 2 80 74 1200 2 05 56 1400 1 91 53 1550 1 82 51 Machine iron 5 1200 1 65 47 1400 Tal 43 1550 1 41 41 Permanent Press Normal 2 5 1000 1 68 50 Normal 2 0 1000 1 38 45 Hand iron 2 5 1000 1 21 37 The specified program running times and electrical consumption values were established under standard conditions EN 61121 A11 Different types of fabrics load size and residual moisture after spinning may effect the specified values These values apply if the laundry is spun in a Miele washing machine before drying 28 Capacity Rated load Fuse rating Technical data
Download Pdf Manuals
Related Search