Miele KWT 1603 Vi Operating and Installation Instructions
Contents
1. Preparing the installation niche N Keep the appliance door closed until it is securely fastened in the niche Tipping hazard Because of the size and weight of the appliance it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging Several plastic bags are included which are numbered alphabetically The bag needed for each step will be marked with its respective letter Anti tip brackets The anti tip brackets D keep the appliance safely secured in the installation niche 2 and prevent it from tipping x lt 0 4 lt 10mm Risk of tipping The installation niche must be securely attached to the wall behind it This is the only way the appliance which is later secured in the niche can be prevented from tipping Two anti tip brackets are recommended for each appliance For side by side installations 4 brackets are recommended 49 Installation In a cabinet with a back wall m Position the anti tip brackets on the left and right in the installation niche so that there is no more than 3 8 10 mm of space between the brackets and the side walls m Mark the drill holes in the anti tip brackets on the back wall and on the ceiling of the installation niche m Set2. Tip Wine bottles should stand upright for at least two hours before serving or better still whole day long to enable sediment to settle to the bottom of the bottle Setting the humidity level The unit comes factory pre set to high humidity If you would like to use the wine unit for long term storage it is recommended that you select the higher humidity The interior climate will then correspond with the conditions in a wine cellar Humidity is raised or lowered for all temperature zones simultaneously be m Touch the access button 8 so it turns yellow N d m Tap the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button is visible m Place one finger on the position of the V button and hold the V button will not be visible Optimum temperature and air quality m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds V L m Tap the V button until 2 appears in the display m Touch the access button J to confirm m By touching the V button you can either increase or decrease the humidity inside the unit B B lower humidity B 1 higher humidity B return to menu m Touch the access button 8 to confirm the setting m Tap the
3. Do not remove them or parts may be damaged m Check the appliance for damage in transit Do not install the appliance if it is visibly damaged If in doubt contact Miele m Loosen the bracket that holds the appliance to the pallet N Caution The appliance is no longer secured and may be unstable 46 m From the rear of the appliance carefully lift it from the pallet Once the appliance is on the ground it can be rolled around RemoteVision module installation optional accessory Always disconnect the appliance from the power supply when performing installation maintenance or service work Install the RemoteVision module before placing the appliance in its installation niche Once connected the RemoteVision module will increase the energy consumption of the appliance The slot for the RemoteVision module is located in the lower area of the back of your appliance m Unscrew the screws on the cover 2 and pull off the sticker m Remove the cover Installation m Push the module into the slot until it locks into place m Connect the appliance to the power supply and turn it on After several seconds the indicator light will come on The indicator light will display different colors one after the other any control light at the end indicates that the module was correctly installed If the indicator light does not come on installation of the module was unsuccessful In
4. Firefox 1 5 or higher Please note that each wireless router manufacturer supplies their own device drivers and setup programs Due to the differences in manufacturers exact router setup instructions are not included in this manual Wording and instructions may vary RemoteVision optional accessory Accessing the RemoteVision control panel m Touch the access button 8 so it turns yellow Nd m Touch the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v LL A Access to the Custom settings mode is now active for approximately 10 seconds m Tap the V button until appears in the display m Touch the access button J to confirm See the table on the following page for a description of each setting in the display m Use the A or V buttons to select the RemoteVision options The module has been connected to the network when r appears in the display If does not appear refer to the Network options section of the XKM 2000 Installation Instruction manual m Press an
5. on both sides of the the custom door appliance are applied to the outermost spaces only m Attach the light switch cover m Screw the brackets onto both sides of the appliance to hold the cover strip 59 Installation Attaching the toe kick cover m Attach the toe kick cover to the plinth The maximum height of the toe kick cover is 4 102 mm from the top of Attaching the cover strips the floor Do not cover ventilation slits in the plinth Risk of damage to the appliance m If required cut the toe kick cover to the required length and height If the frame width is narrow the cover strip side piece may need to be shortened To determine the required length of the side piece one test piece is enclosed with the cover strip place m Remove the foil from the adhesive strips 60 Installation m Cut the cover strips long for the sides of the door to the required length X m Push the cover strips on the into the gap between the furniture door and glass pane m Cut the cover strips short for the top and bottom of the door to the required length Y m Push the cover strips into the gap between the furniture door and glass pane Mounting the air separator The air separator keeps the supply and exhaust air separate This prevents warm exhaust air from flowing into the machine optimizing
6. 50 F 10 C to 90 F 32 C N 60 F 16 C to 90 F 32 C ST 60 F 16 C to 100 F 38 C T 60 F 16 C to 110 F 43 C Operating in a room which is too cold will cause the compressor to switch off for too long causing the internal temperature in the appliance to rise with the risk of food deteriorating and going off 35 Installation Installation site The appliance should be installed in a dry well ventilated room Do not install the appliance outdoors in an environment with dripping water in rooms which are at risk of frost The installation location should not be exposed to direct sunlight nor near a heat source such as an oven radiator etc The ambient temperature should not drop below 55 F 13 C or rise above 110 F 43 C otherwise malfunctions may occur If installation next to a heat source is unavoidable observe the following minimum distances from the heat source 1 14 8 cm from an electric cooktop or electric oven 12 30 cm from a gas or oil cooktop range or oven The following should also be taken into consideration The electrical outlet must be easily accessible in case of an emergency not concealed behind the appliance The plug and cord must not touch the rear of the appliance as they could be damaged by vibrations from the appliance 36 Do not plug in other devices behind this appliance Do not
7. Optimum temperature and air quality Insulation panels for thermal separation The unit has two fixed insulation panels to divide the interior into the three different temperature zones This allows you to store three different types of wine such as red wine white wine and champagne The correct serving temperature is crucial for the taste and therefore your enjoyment of the wine The following temperatures are recommended for the different types of wine Red wine 57 F to 64 F 14 C to 18 C Ros 50 F to 54 F 10 C to 12 C White wine 46 F to 54 F 8 C to 12 C 45 F to 48 F 7 C to 9 C Sparkling wine 41 F to 45 F EGTC Champagne Temperature display The temperature display on the control panel always shows the required temperature The temperature display will flash if the temperature in one of the zones is too high or too cold Tap the V and A sensor buttons to raise lower the temperature 1 or hold them down to move through the temperature range more quickly Optimum temperature and air quality Temperature unit Fahrenheit Celsius The temperature can be displayed in degrees Fahrenheit F or Celsius C be m Touch the access button 8 so it turns yellow e d m Touch the sensor button for any temperature zone so that it turns yellow m Note the position of the V button but do not touch m Touch th
8. This makes the compressor run for longer causing the temperature in the appliance to fall automatically What if the compressor kicks on very frequently and for too long The ventilation slits in the plinth and in the top of the appliance are covered or dusty Clean with a vacuum or brush The door has been opened too frequently Once the appliance returns to the set temperature the compressor will turn off The door is not closed Check that the door has been closed properly 28 Frequently asked questions What if the alarm is ringing Possible fault Solution The appliance door has been open for longer than 5 minutes Close the door What if the alarm is ringing and the alarm indicator is lit The door is not closed One of these conditions has caused the The ventilation slits are covered temperature in the appliance to become too warm A large amount of wine was stored at once Once the alarm condition has been corrected the alarm will turn off and the There has been a power failure alarm indicator will stop flashing What if a fault message with _F appears in the temperature display A fault has occurred Contact Miele Technical Service What if the display lighting is not working The display lighting turns off automatically depending on the time set See Display lighting If the display lighting sti
9. V button until a c appears in the display m Touch the access button J You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated 20 If you have selected a higher humidity setting the fans will cut in This is to ensure that the humidity is uniformly distributed throughout the interior Whenever the unit door is opened the fans will automatically switch off temporarily Air filtering with an active charcoal filter External air passes through the filter before entering the unit The active charcoal filter ensures that only clean odor free air enters the unit creating additional protection against odor contamination The filter will need to be changed periodically or when odors are present in the unit See Cleaning and Care Active charcoal filter for more information Storing wine Storage tips Always unpack bottles do not store wine in crates or boxes Always lay bottles on their side for storage This keeps the corks moist from the inside preventing air from entering Store similar wine varieties beside each other on the same shelf to avoid restacking and the need to disturbed other bottles Before serving ros and red wine bottles should spend at least two hours upright and open to reach optimal drinking temperature Sparkling wine and champagnes sho
10. come on The access button will light in the control panel The preset temperatures factory settings are reached after a few hours Turning off the appliance with the main switch does not safely isolate it from the power supply Settings Using the settings This appliance is operated with the use of touch keys activated by a finger An available button will appear white Aselected button will appear yellow be m Touch the access button so it turns yellow A On the control panel you will now see the sensor buttons of the three temperature zones The factory default settings for the temperature zones are as follows upper temperature zone red temper middle temperature zone white temper lower temperature zone wine storage 10 display light m To turn the display lighting on or off when the door is closed touch the display light sensor button N ou m To change the settings touch the sensor button for the temperature zone you wish to set The selected sensor button appears yellow You can now select from the following settings for the selected zone s or change the pre set temperature s as desired wine white red storage temper temper For more information on setting the temperature see Optimum temperature and air quality Settings m To de select a temperature zone touch the sensor button for that particular zone so that it turns wh
11. min 90 gt 10 mm The dimensions of the door fronts and handles will vary according to each individual kitchen 3 g 10 mm A B C KWT 16X3 Vi 26 5 4 677 mm Door front max 1 1 gt 38 mm Door handle Door dimensions open min 115 The dimensions of the door fronts and handles will vary according to each individual kitchen A B C D KWT 16X3 Vi 26 Door front max Door 11 3 4 677 mm 1 1 4 38 mmy handle 299 mm 40 Dimensions Niche dimensions 84 2134 mm 41 Dimensions Power supply 515 6 150 mm 1 Power supply A KWT 16X3 Vi 12 305 mm Power bars or extension cords are not safe risk of fire Do not use them to connect the appliance to the power supply UEM E 42 Dimensions Door front dimensions 17 la 18 439 473 mm ai 63 I 1623mm H 10 14 257 mm Sy 102 mm 43 Installation Before you begin Read these instructions completely and carefully Have the appliance installed by a qualified technician according to the enclosed installation instructions To reduce the risk of injury or damage to the product two people should be used for installation These installation instructions are intended for use by qualified installers In addition to these instructions the applianc
12. mm The guide dimension of 1 1 4 32 mm is Hire related to a niche height of 84 AO 4 mm x 15 mm EDT O m Screw the attachment plate lugs to the overhead furniture fixtures m Align the custom doors with a level Note When unscrewing the height adjustable feet proceed gradually alternating between left and right f using a wooden beam as an alternative anti tip device rotate the appliance all the way toward the wooden beam 54 Installation If there is no way to attach the top of the appliance it can be attached to the sides of the installation niche m Pull out the plate side lugs 2 m Secure the attachment plate side lugs If there is a fairly large gap above the appliance cut a wooden beam to fit exactly and place it in the gap m lf necessary shorten the filler strip to the required height m Place the 2 strips on top of each other m Insert the filler strip until you hear it click into place 9 For a side by side combination the filler strips from both appliances are put together to form one long filler strip m Take the peg from the side by side merging kit and insert it halfway into the filler strip rail on the left side appliance m Place the second filler strip on the peg and press both filler strips together m Insert both filler strips into the installation space above the appliance
13. of the house checked by a qualified electrician P Only connect power to the appliance when all installation work is complete IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top heavy and must be secured to prevent the possibility of tipping forward Keep the door closed until the appliance is completely installed and secured per installation instructions P This appliance must be installed and connected in compliance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty P Do not operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner Contact Miele s Technical Ser vice Department P This appliance must not be used in a non stationary location e g on a ship P Do not install the appliance in a room with too low an ambient temperature e g a garage as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature Use P This appliance is not designed for commercial use It is intended for use in domestic households and in similar working and residential environments such as shops offices and similar work environments by customers in hotels motels Bed amp Breakfasts or similar residential environments P T
14. plug in other devices behind this appliance If the room is too cold it will cause the cooling system in the appliance to remain off for too long This can cause the temperature in the appliance to rise resulting in damage Base A fully loaded appliance is very heavy The load bearing capacity of your floor must meet the following requirements KWT 16x3 Vi 704 Ibs 319 kg To ensure that the appliance is installed securely and functions properly the base must be flat level and made of a hard rigid material If in doubt contact Miele Furniture fixtures The new appliance will be mounted securely to adjacent and overhead furniture fixtures For this reason it is essential that all attachable furniture fixtures are connected securely to the base or the wall by suitable means Ventilation The air intake and outlet must not be blocked or covered in any way They also need to be dusted cleaned on a regular basis Installation Installation niche To ensure safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation dimensions See Niche dimensions The side walls of the installation cavity must be plumb The minimum thickness of the side walls and the top wall must be 5 8 16 mm The minimum thickness of the toe kick panel must be 1 2 13 mm A thickness of 3 4 19 mm is recomme
15. rack so that they touch the wooden guide rail CD Maximum capacity m To remove the display rack pullitup The unit can hold approx 102 bottles and out then attach it to the rear 0 75 I position on the wooden rack The bottles can now be stored on the wooden rack in the usual manner Additional display racks are available from Miele 22 Storing wine Display lighting The display lighting can be turned on if you wish the bottles to be lit up even when the door is closed be m Touch the access button J so it turns yellow Turning on display light m Touch the Display light sensor button so that it turns yellow The display lighting will now remain on in the 2 lower temperature zones even when the door is closed When the door is open the interior lighting also comes on in all three temperature zones Turning off m Touch the Display light sensor button so that it turns white The display lighting is now turned off When the door is closed the interior is dark and when the door is opened the interior lighting comes on Duration of the display lighting The display lighting is factory pre set to 30 minutes display light m To change this time setting press and hold the Display light sensor button for 2 seconds The set time in minutes appears in the display Use the V and buttons next to the display to change the duration of the lighting in increments of 15 minute
16. that case repeat the process If that does not correct the problem contact Miele m Pull the antenna 9 straight out m Guide the cover 2 over the antenna and screw on the cover m Angle the antenna so that it faces to the right or left m f necessary disconnect the power supply and continue installing the appliance If you would like to connect your appliance to the Home Security System proceed now see Home Security System 47 Installation Home Security System HSS If desired the wine storage unit can be connected to the security system of your house via a switching contact If connected you will be immediately informed of rising temperatures in the wine cooler The Home security system connection must be hooked up before the unit is installed Contact a qualified electrician or authorized agent from alarm company to connect your home s security system to the wine cellar Always disconnect the appliance from the power supply before performing installation maintenance or service work m Remove the toe kick panel from the appliance 48 m Choose the desired switching contact and connect according to alarm system requirements Output of the Home Security System on the electronic board NC NO Com NC normally closed Com common NO normally open Switching capacity 120 V 250mA 30 V 1A m Continue with the appliance installation Installation
17. the brackets aside they will be needed again later Screws are supplied with the appliance for various applications materials m screw the back wall of the cabinet in several places directly to the wall behind it For this use suitable plugs screws depending on the type of wall If the anti tip brackets cannot be attached securely with the screws supplied an alternative anti tip device can be used Assure that there are no electrical wires or plumbing in the area which the screws could penetrate risk of injury and damage m Now attach the installation niche to the wall The built in cabinet must be secured to the wall behind it with several screws 50 Installation In a cabinet without a back wall Securing an alternative anti tip device If the anti tip brackets cannot be attached securely an alternative anti tip device can be used Ensure that there is no give between the appliance and the anti tip device If possible always screw the wooden beam to existing studs m screw the cabinet to the wall behind it in several places using suitable mounting brackets For this use suitable plugs screws depending on the type of wall ni Cut a wooden beam cross section min 3 x 4 75 mm x 100 mm to the required length The length is equal to the width of the installation niche If the installation cavity is deeper than the appliance select a beam w
18. until they click into place 55 Installation m Open the appliance door Preparing the custom door i m Open the appliance door m Unscrew the installation supports 42 from the appliance door m Loosen the remaining screws from A the strips 13 on each side of the door then remove m Screw the attachment plate lugs to the adjacent furniture fixtures m Set aside the screws and side strips M you will need them again later With side by side combinations only the external side of the appliances can i Take off the light switch cover be secured to the niche m Close the appliance door 56 Installation m Measure the distance X between the bracket and the overhead furniture fixtures m Loosen the two nuts Set aside the nuts you will need them again later m With the inside facing up lay the custom door on a stable surface to avoid scratch marks place some plastic or a cloth on the surface e m Mark the distance X on the back side of the custom door m Also calculate and mark the center of the custom door Y m Remove the mounting frame from the appliance door and position it according to the markings on the custom door m Pre drill the holes m lightly screw on the bracket using the pre drilled holes Attach the bracket to each attachment point with at least one screw m Attach the bracket at the top with at le
19. 15 P plug ready for connection to a 120 V 60 Hz supply The fuse rating is 15 amps The appliance requires a 3 wire receptacle The receptacle must be installed by a licensed electrician only In the case of side by side installations a separate outlet must be used for each appliance Ideally the power outlet should be next to the appliance and easily accessible Do not connect the appliance to the power supply by an extension cord Extension cords do not guarantee the required safety of the appliance danger of overheating If any changes are needed to the household wiring or power supply this work must be performed by a qualified electrician 63 RemoteVision optional accessory Miele s RemoteVision Wi Fi technology creates a virtual link between your appliance and our monitoring center If a fault occurs Miele s client service center will be notified and contact you or another trusted individual identified on your call roster in order to gain access to your appliance to fix the problem For information on set up and installation of the RemoteVision module see the Installation section of this manual 64 Be sure your wireless system meets the following requirements A wireless router that supports an IEEE 802 11b g protocol Windows XP or newer operating system Mac OS X 10 3 or higher Cable or DSL modem Microsoft Internet Explorer 6 or higher Safari 2 0 or higher
20. a Miele Operating and Installation Instructions Wine Storage Unit To prevent accidents and appliance damage read these instructions before installation or use en US CA M Nr 09 920 680 Contents IMPORTANT SAFETY INSTRUCTIONS 220020055 4 Guide to the wine storage unit 7 Before USC sucesor yea dope EE EEG e S a oce 9 Before using for the first time 9 Turning the appliance On Off ea e cers liliis ses 9 Settings css eo baa a ot 10 USING tlie Settlngss se mde qe REG e Ree ded geredet ina 10 Custom sSeNlllgss s dei ia ier T Edere ete er Pepe dubie edet 11 Turning the button sound On Off liiis ee 12 Turning off for longer periods of time 13 Allarmi voro gan bp SESE EX CD X HEC NES Oed Sad x P deo abb os 14 Temperature alam iaia ete x cox ae EA I ende REOR dee aa ol ee ode 14 DooraemMez reina 14 Optimum temperature and air quality 15 Setting the temperature 15 unie ape lago iaia iii Pa na 19 Storing WINE ei ici peer ed Pe eee 21 WoodertreckKs sas a dca yd RN i Pal a ate oed ia e 21 Bottle display Tac Kus ig aot ci ar e dem d AR eR afe 22 Maximum capacity 22 Display lighting sace aret roe Rene ata eta ia dure 23 Detrosting es iaeaea ree Seo det Aue ESO NE RIA Eo ut YU AR daw bus 24 Cleaning and care 25 Cleaning the interiori sx x etra rac e EZ pen e 26 VentllatiOnislits ersi oc d RERO uo De xu patte t ere OR a ob d at n OE Ru aede E 26 POIS c oriali a 26 Active charcoal filter
21. a magnet can cause damage Disposal of your old appliance P Before disposing of an old appliance first make the door latch or lock unusable P Take off the door P Leave the shelves in place so that children may not easily climb inside P Consult with your municipal policy on recycling P Be careful not to damage any part of the pipework while awaiting disposal by puncturing the refrigerant channels in the evaporator bending any pipework scratching the surface coating Splashes of refrigerant can damage the eyes 6 P Your old refrigerator may have a cooling system that used CFCs chlorofluorocarbons CFCs are believed to harm stratospheric ozone If you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislation Make sure the CFC refrigerant is removed and disposed of by a qualified technician SAVE THESE INSTRUCTIONS Guide to the wine storage unit Circulation fans Active charcoal filter 2 Wooden racks Insulation panel to separate the upper and middle temperature zones 4 Bottle display rack 8 Control panel Insulation panel to separate the middle and lower temperature zones Main switch to turn the appliance On Off Glass door with UV filter 8 Connection behind the ventilation gap for
22. ast 6 screws The bracket includes a variety of holes for the various design options of custom doors When performing any work on the custom door always observe the following Always select the best load bearing surface of the custom door as the location for screws Select a screw length that is shorter than the thickness of the door front m Secure the door handle to the front of the appliance from the inside 57 Installation Attaching and aligning the custom door front m Open the door and hang the custom door with the mounting frame over the threaded bolts 44 m Put the side strips 13 back into place and screw them completely down on both sides of the appliance door Bag E contains spare screws for this purpose m Screw the nuts 9 a few turns onto the threaded bolts 44 Do not tighten the nuts completely m Close the appliance door and check the distance to doors of adjacent furniture fixtures 58 m Align the custom door height with the threaded bolts m Now tighten the nuts 45 on top This secures the appliance door Installation Attaching the covers m Insert the cover strip into the space between the appliance and the side m To mount the cover strips on both sides of the door click them into panel mE place from bottom to top into the For side by side combinations the gap between the appliance door and cover strips
23. cidents and machine damage This appliance is intended for residential use only Use only as described in this Operating manual Only use the appliance for its intended purpose This appliance complies with current safety requirements Improper use of the appliance can lead to personal injury and material damage Keep these operating instructions in a safe place and pass them on to any future user Warning At an altitude of more than 8200 ft 2500 m the glass door can break Danger of injuries Electrical safety P Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt P Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse P Do not use an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding System It is imperative that this basic safety requirement be met If there is any doubt have the electrical system
24. d hold the access button for 2 seconds to confirm the change m To return to the main menu tap the V button until a solid r appears in the display m Press the access button 8 to confirm m Tap the V button until a c appears in the display m Touch the access button J You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated 65 RemoteVision optional accessory MasterCool control panel options for RemoteVision Status indicators Description of function Flashing r Module booting phase Flashing r Not connected to network Flashing r Connection to network established no IP address assigned Solid FS Connected to network Flashing r In Ad Hoc Mode not connected Flashing r In Ad Hoc Mode connected Selectable Description of function options re Back re Reboot the module r3 Reset to factory settings rH Enter Ad Hoc Mode Note If you cannot select any option other than r Back the module has not been installed correctly 66 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nati
25. desired temperature zone so that it turns yellow wine white red storage temper temper m Select the preferred temperature setting so that the sensor button turns yellow The setting white temper is not available in the lower temperature zone Optimum temperature and air quality Temperatures can be independently set in all three zones The unit comes factory pre set for white wine red wine and wine storage The temperatures can be changed as desired Nd m Select the temperature zone you would like to change the temperature in dtc y Jap Use the V and A buttons next to the temperature display to set the temperature warmer or colder The temperature will change in 1 increments Hold the button down to change the value continuously When the lowest or highest temperature is reached the corresponding arrow will no longer appear in the display The factory suggested temperature for the selected zone appears in yellow 16 Once you have adjusted the temperature check the temperature after a few hours It will take this long for the appliance to reach the temperature If after this time the temperature is still too high or too low it should be adjusted again Temperature ranges upper temperature zone 3 C to 18 C or 37 F to 64 F middle temperature zone 3 C to 18 C or 37 F to 64 F lower temperature zone 8 C to 18 C or 46 C to 64 F
26. e appliance The side panels of the housing must be even The housing unit panels must be at least 5 8 16 mm thick The plinth facing must be at least 1 2 13 mm thick preferably 3 4 19 mm Check the installation niche To ensure a safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation requirements m Check the base see Installation m Check the dimensions of the cavity m Check that the cavity is square m Check the location of the power outlet m Check that all furniture parts in the vicinity of the appliance are securely connected to the wall m Check that the adjacent furniture fixtures do not collide with the open door Before installation Caution the appliance is very heavy Use caution when unpacking and opening the door danger of tipping m To protect the base from damage during installation attach a hard board linoleum etc to the floor in front of the intended installation location m Remove any cable clips from the back of the appliance m Take the supplied accessories out of the protective packaging 45 Installation m Do not remove the installation supports from the appliance doors They will be used later in the installation niche There are transportation safety devices inside the appliance to protect the shelves until installation is complete
27. e access button f again so it turns white Only the access button 8 is visible m Place one finger on the position of the V button and hold the V button will not be visible 18 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v C A m Tap the V button until appears in the display m Touch the access button J to confirm m By touching the V button you can select either Fahrenheit or Celsius for the temperature display B Fahrenheit 1 Celsius return to menu m Touch the access button J to confirm the setting m Tap the V button until a c appears in the display m Touch the access button J You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Optimum temperature and air quality Humidity In a conventional refrigerator the humidity levels are too low for storing wines High humidity levels 60 70 are very important for the storage of wine so that the corks remain moist Under low humidity the corks dry out from the outside and can no longer seal the bottles properly This is why wine bottles should always be stored lying down so that the wine can keep the corks moistened from within If air enters the bottle a wine will inevitably spoil
28. e must be installed in accordance with all local codes In the absence of a local code the following should be used Inthe USA the National Electric Code ANSI NFPA 70 latest edition State and Municipal codes and or local codes In Canada the Canadian Electric code C22 1 latest edition Provincial and Municipal codes and or local codes Tools needed for installation Cordless screwdriver Torx screwdriver Hammer drill Wood drills in different sizes Hammer Rachet 5 16 8 mm Adhesive tape 44 Multi grip pliers Level Tape measure Square When fastening the cabinet to the wall behind it see Installing the appliance use suitable plugs screws depending on the type of wall several mounting brackets if required Other Stepladder Dolly hand truck Wooden beam cross section min 3 x 4 75 mm x 100 mm as an alternative tilt protection length depends on the width of the installation cavity Wood screws in different sizes Optional accessories Merging Kit for side by side installation RemoteVision module for wireless installation Installation Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance The unit corners must be at right angles as otherwise the furniture door will not align correctly with the 4 corners of th
29. hich has a larger cross section or attach two beams 51 Installation The beam must cover the appliance by at least 2 50 8 mm m Mark the installation height lower edge of the beam on the rear wall of the niche m Select screws according to the thickness of the wooden beam Example 3 2 89 mm screw for 2x4 beam m Determine the number of screws based on the cavity width to ensure that the beam will be attached securely m Locate wall studs near the rear wall of the cavity and mark drill holes in the beam m Pre drill the wooden beam m Attach the wooden beam to the rear wall of the niche 52 Sliding the appliance into the installation niche If a side by side installation is desired connect the two appliances together See the Installation Manual included with the Merging Kit m To protect the corners of the installation space attach edge protectors where needed not included Installation m Plug the appliance into the power outlet The plug of the appliance should be easily accessible after installation If the plug is not accessible after the appliance has been installed disconnection from the power supply should be completed via the circuit breaker In the case of side by side installations a separate outlet must be used for each appliance m To prevent the power cord from becoming caught Tie a piece of
30. his appliance is not intended for outdoor use P Persons who lack physical sensory or mental abilities or experience with the machine should not use it without supervision or instruction by a responsible person P To reduce the risk of injury do not allow children to play in on or near the appliance especially in the door hinge area P Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance P Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous with time P Do not block the ventilation gaps in the plinth or the top of the appliance housing unit as this would impair the efficiency of the appliance increase the electricity consumption and could cause damage to the appliance IMPORTANT SAFETY INSTRUCTIONS P Never use a steam cleaner to clean the appliance Pressurized steam could damage electrical components and cause a short circuit P Do not use any electrical equipment inside the appliance Danger of injury The following applies to stainless steel appliances P Do not use sticky notes transparent adhesive tape masking tape or other types of adhesive on the coated surface of the appliance door These will damage the surface causing it to lose its soil resistant protective coating P The high quality surface coating of the appliance door is susceptible to scratches Even
31. ickness of the partition is f 16 mm d If there is a partition with a thickness from g 16 mm to 6 5 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included The Merging Kit will also be needed The Merging Kit is available from Miele Installation with partition without using the Merging Kit If there is a partition with a thickness of more than 6 g 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included the Merging Kit is not necessary Side panels If one side of the appliance is visible a side panel must be used The side panel must be firmly secured to the wall the floor and the overhead furniture fixtures before the appliance is placed in the cavity The dimensions of the side panel are taken from the opposite wall of the installation space During installation ensure that the cavity is square and the measurements are correct Adjusting the door opening angle optional accessory Depending on the installation site it may be necessary to adjust the door opening angle to 90 m Open the door m Insert the banking pin through the holes and drive in with a hammer The door opening angle is now limited to 90 39 Dimensions Door dimensions open
32. ining soda ammonia thinners or chlorides cleaners containing descaling agents or lime removers abrasive cleaners stainless steel cleaners dishwasher soap powder caustic oven cleaners scouring pads steel wool hard brushes glass cleaners with the exception of the glass door front metal scrapers eraser sponges steam cleaning products Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly 25 Cleaning and care Before cleaning m Use the main switch to turn the appliance off completely The main switch is located on the right side underneath the control panel m Unplug the power cord m Remove any bottles from the appliance and store it in a cool place m Take out any removable parts e g shelves Cleaning the interior m lt is recommended to clean the interior once a month m Use a mild solution of warm water and liquid dish soap m Clean the wooden racks with a damp cloth Do not allow the racks to become too wet m After washing wipe down the interior and accessories with a clean wet cloth then dry with a soft cloth Leave the appliance doors open for a short time so the moisture can evaporate 26 Ventilation slits m Check the ventilation slits regularly Remove any dirt dust with a vacuum cleaner or brush Clean as needed Door seals Do not use a
33. ite or select another sensor button be m To leave the settings menu touch the access button so it turns white The last settings entered are stored The sensor buttons for the three temperature zones disappear from the control panel Even if you do not touch the access button the electronics will switch back to normal after about 1 min Custom settings In the custom settings mode you can select and change functions The function possibilities are described in the respective chapters of this manual mode Function Display text Temperature F 9c m F RemoteVision r Module settings optional accessory Button sound on off Exit Custom Settings Humidity settings Settings Turning the button sound On Off If you prefer the buttons to be silent when touched the button sound can be turned off m Touch the access button 8 so it turns yellow Sew d m Touch the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible 12 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds m Tap the V butto
34. less expressly approved in writing by the Miele Ser vice department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at http mieleusa com mielecare 31 32 ii Installation Instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information To prevent accidents and machine damage read these instructions before installation or use Caring for the environment Disposing of the packaging materials The packaging is designed to protect the appliance from damage during transportation The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Return the packaging to your dealer 34 Disposal of your old appliance Old appliances may contain materials that can be recycled Please contract your local recycling authority about the possibility of recycling these materials Instead please co
35. ll does not turn on after 15 minutes with the door closed contact Miele Technical Ser vice A white coating has formed around the wine corks The corks are made of a material which has caused a chemical reaction oxidation The white coating can be removed with a dry cloth The coating has no effect on the quality of the wine Mildew is beginning to form on the wine bottle labels Depending on the type of adhesive used mildew may begin to form on the labels Wash the wine bottles and remove any adhesive residue 29 Causes of noises Normal noises What causes them Brrrrr A humming noise is made by the motor compressor This noise can get louder for brief periods when the motor switches on Blub blub A gurgling noise can be heard when the coolant circulates through the pipes Click Clicking sounds occur whenever the thermostat switches the motor on or off Sssrrrrr In multi section and frost free appliances the movement of air circulating through the appliance can sometimes just barely be heard In appliances with a water tank a humming noise can be heard when the water pump is running Crack A cracking noise can be heard when the appliance materials expand Please bear in min d that a certain amount of noise is unavoidable from the compressor and the coolant circulating through the system Noises that yo
36. n until 6 appears in the display m Touch the access button J to confirm m By touching the V button you can choose between b U Button sound is off b 1 Button sound is on 5 Return to menu m Touch the access button J to confirm the setting m Tap the V button until you see c in the display m Touch the access button J You have now left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time for example during a vacation some precautions should be taken m Turn the appliance off at the main switch m Unplug the appliance m Clean the interior m Leave the doors open to prevent odors Alarm The appliance is equipped with an alarm system to ensure that the temperature does not rise unnoticed because of energy loss or an open door The alarm system is always operational it does not need to be turned on Temperature alarm If the temperature becomes too warm an alarm sounds the alarm indicator turns red and flashes At the same time the affected zone flashes in the display If you use the Home Security System a temperature alarm will also trigger your security alarm Once the temperature alarm is turned off the security alarm will also shut off The ala
37. nded Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry The total weight of the decorative panel s must not exceed the following KWT 16x3 Vi 137 lbs 62 kg Do not install a solid custom door panel onto the front of the appliance Condensation will form between the glass and custom door 37 Installation Installation options There are many different installation options You are limited only by the design of the kitchen The door hinge cannot be exchanged Single column The appliance can be installed at any preferred location in the kitchen However be sure the door will open and close properly in the chosen location 38 Side by side This appliance can be installed side by side with another fridge freezer using a Merging Kit The Merging Kit is available from Miele Contact Miele or your dealer for specific information about which combinations will work with your appliance For instructions on how to attach the appliances and install the heating mat please refer to the instructions included with the Merging Kit available from Miele Appliances attached together using the Merging Kit If the appliances are installed directly next to each other without a partition they need to be attached together using the Merging Kit Installation Installation with partition using the Merging Kit The minimum th
38. ntact your municipality s waste collection center to return and recycle electric and electronic appliances Please take care not to damage the pipework while the appliance is being stored for transport to a waste disposal facility By protecting the pipework you help keep the coolants and compressor oil from contaminating the environment Before discarding an old appliance disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard Installation NIn areas with a tropical climate over 100 F 38 C and more than 70 air humidity the wine cooler must only be operated in air conditioned locations Otherwise the function of the machine cannot be guaranteed Have the appliance installed by a qualified technician according to the enclosed installation instructions NWARNING This appliance is top heavy and must be secured to prevent the possibility of tipping forward Anti tip protection is required Keep the door closed until the appliance is completely installed and secured as per the installation instructions Empty weight of your machine KWT 16X3 Vi 337 Ibs 153 kg Climate Range The appliance is designed for use within certain climate ranges ambient temperatures and should not be used outside this range The climate range of this appliance is stated on the data plate inside the appliance Climate Ambient room temperature range SN
39. ny oils or grease on the door seals as these will cause the seals to deteriorate and become porous over time m Clean the door seal with water only and dry thoroughly Active charcoal filters Replacement filters are available from Miele x m Remove the cover over the filter use a screwariver if necessary m Remove the old filter 2 and replace with a new active charcoal filter m Replace the cover over the new filter After cleaning m Return all bottles to the appliance m Insert the plug into the power outlet and turn on the appliance at the main switch Cleaning and care Changing the light bulbs Never touch a halogen bulb with Do not remove the light covers for bare fingers the display lighting Should the When inserting a glass halogen lighting covers be damaged or need bulb always hold with a soft cloth to be removed due to damage do not look directly or with an optical instrument at the lighting Interior lighting The lighting automatically switches off after the door has been open for approx 5 minutes This is not a fault After the bulb has cooled for a short time it will turn on again m Pull the defective light bulb from the If the light does not come on when the Boeken door is opened briefly the light bulb m Place the new bulb in the socket should be changed Halogen bulb type m Use the main switch to turn the SASSO SE appliance off m Pu
40. onwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Miele www miele shop com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 Fax 905 532 2290 www miele ca professionalQmiele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercareQmiele ca general and technical enquries 67 KWT 1603 Vi KWT 1613 Vi en US CA M Nr 09 920 680 00
41. rage conditions for your wine Temperature Wine can be stored at temperatures between 41 F and 64 F 5 18 C If you would like to store red and white wines together choose a temperature between 50 F and 54 F 10 12 C Most white wines are palatable at this temperature It is best to take red wine out of the appliance about 2 hours before drinking Open the wine to allow it to breathe and to develop its aroma After 2 hours red wine will be at the correct temperature for drinking Storage temperatures above 72 F 22 C will cause wines to mature too quickly By contrast wine should not be stored below 41 F 5 C since it will not mature fully at this low temperature Fluctuations in temperature put wine under stress and interrupt the maturing process Therefore it is important to maintain a constant temperature Setting the temperature The factory default settings for the temperature zones are as follows The upper temperature zone is set for optimal red wine storage Red temper 61 F 16 C The middle temperature zone is set for optimal white wine storage White temper 50 F 10 C The lower temperature zone is intended for wine storage in general Wine storage 52 F 11 C You can change the purpose of the zones as you wish For example you can store white wine in the upper temperature zone as long as you adjust the temperature accordingly EN x m Tap the sensor button for the
42. rm will sound and the display will flash if too much warm air flows into the appliance for example when bottles are being loaded re arranged or unloaded a large number of bottles are being stored for the first time the power fails As soon as the alarm condition is corrected the alarm signal turns off and the affected zone stops flashing in the display The alarm indicator goes out 14 Turning the temperature alarm Off dare m To turn the alarm off early press the alarm sensor button The alarm signal turns off The alarm indicator remains red and the corresponding appliance zone continues to flash until the alarm condition is corrected Door alarm If the appliance door is left open for over 5 minutes an alarm signal will sound and the alarm indicator will light up Once the door is shut again the alarm will stop and the alarm indicator will go out Turning the door alarm Off MESS m To turn the alarm off early press the alarm sensor button The alarm indicator and signal will turn off Optimum temperature and air quality Wine will continue to mature depending on the surrounding conditions The length of time which wine can be kept in good condition will therefore depend not only on the temperature but also on the air quality The wine storage unit provides a constant temperature increased humidity and an odor free environment creating the best possible sto
43. s You can set the lighting to last for 15 30 45 60 75 or 90 minutes m To confirm the setting touch the access button 8 until all the displays go out If the door is closed before the set time is completed the lighting duration starts over again from the beginning 23 Defrosting During normal operation condensate and frost can form on the rear wall of the refrigerator and drawers You do not need to remove this build up it will defrost and evaporate automatically with the heat generated by the appliance 24 Cleaning and care To reduce the risk of electrical shock disconnect the appliance from the power supply by shutting off the power main tripping the circuit breaker or unplugging the power cord before maintenance Never use cleaning agents containing abrasive substances such as sand soda acids chlorides or chemical solvents Non abrasive cleaning agents are also unsuitable as they can cause matte areas to appear Avoid getting water on the solid wood facing or the shelves Do not use a steam cleaner to clean this appliance Pressurized steam could penetrate electrical components and cause a short circuit Do not allow water to get into the electronic unit or lights The data plate located inside the appliance must not be removed It contains information which is required in the event of a service call To better maintain your appliance avoid the following cleaners conta
44. s 26 Changing the light bulbs LL 27 Frequently asked questions 28 Causes of noises ili eee 30 After sales service 31 Caring for the environment 0 00 i sse 34 Contents Installation 2o ebd ilaele 35 Climate Ranges ude ned eet adore dera pera CR BOR d JUR eod dde s 35 Installation site isses I n 36 Scie MM 36 Errilt re fiXtUl 68 23 2 24 nae t putare o a e m Ee patr de i 36 Custom door panels asa ados ves ee dee RR oan Eee hee e een 37 Installation options x vere Yo Y ex Ree ek dee X POE ERE ONE eR god 38 Adjusting the door opening angle optional accessory 0 39 DIM NSIONS 62544504 Hee RR oed Red E REOR HY ERO RE e en d YES 40 Installation iilii iilii I 44 Before you DEgin Li 44 RemoteVision module installation o 46 Home Security System HSS neri Peso wade pee FETRXGGE GU eu 48 Preparing the installation niche 0 49 Sliding the appliance into the installation niche 52 Aligning the appliance 53 Attaching the appliance to the installation niche L 0 54 Preparing the custom door 56 Attaching and aligning the custom door front 58 Electrical connection 63 RemoteVision optional accessory 00000 c eee 64 Accessing the RemoteVision control panel 65 Contact details 67 IMPORTANT SAFETY INSTRUCTIONS When using the appliance follow basic safety precautions including the following Read all instructions before installation and use to prevent ac
45. string to the middle of the power cord and feed it forward under the appliance When sliding the appliance in pull the cable forward 2 m Carefully slide the appliance into the space If resistance is felt when attempting to slide the appliance into the installation niche for example because the floor is uneven m Turn the rear adjustable wheels slightly outward see Aligning the appliance then push the appliance in Be careful not to damage the power cord attached to the floor m Remove the edge protectors Aligning the appliance m Align the appliance with the custom front 6 4 38mm lin I 3 4 19mm lt a G M a 11 4 32mm The installation aids 3 on the appliance door have been designed for custom door thicknesses of 3 4 19 mm and 1 1 2 38 mm The height adjustable feet at the front and rear can all be adjusted from the front Front feet Adjust with a rachet 5 16 8 mm Rear feet Adjust with a cordless screwdriver and or a rachet 5 16 8 mm for fine adjustment m Use a level to align the installation aids 9 on the door 53 Installation Attaching the appliance to the Important installation niche When unscrewing the height adjustable feet proceed gradually alternating between left and right m Unscrew the height adjustable feet until the mark on the base has reached the indicated guide dimension 1 1 4 82
46. t the light cover back on and turn clockwise into place To reduce the risk of electric shock disconnect the appliance from the power supply by unplugging or tripping the circuit breaker Restore power to the appliance Y m Turn the light cover counterclockwise and pull out 27 Frequently asked questions With the aid of the following guide minor problems can be corrected without a ser vice call Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage and may void the warranty What if the appliance does not get cold Possible fault Solution The machine is not turned on Check whether the appliance is switched on at the main switch The machine is not plugged in Check that the plug is correctly inserted in the power outlet Check that the fuse has not tripped Reset the circuit breaker If the breaker trips again the appliance or the outlet may be defective Contact Miele or a qualified electrician The temperature is set incorrectly Check the display What if the temperature is too low Select a warmer temperature See Setting the temperature The door is not closed Check that the door has been closed properly A large amount of bottles has been put in the appliance at the same time
47. the Home Security System HSS Guide to the wine storage unit Control panel wine white red display alm i Storage temper temper light pp EY Access button Long term wine storage 2 Upper temperature zone Short term storage of white wine at a Middle temperature zone moderate temperature 8 Short term storage of red wine at a moderate temperature On Off sensor button for the display 2 Lower temperature zone 8 Temperature display Allows you to set the temperature V colder warmer lighting and 19 Off sensor button for the temperature set the duration of the display and or door alarm lighting V shorter longer only visibly when the relevant function is activated Before use Before using for the first time m Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap Dry with a soft cloth If the appliance was transported or laid horizontally for any reason allow it to stand vertical for at least 8 hours before turning it on Failure to do so will affect the functioning of the appliance Turning the appliance On Off m Open the appliance door m Turn the appliance On Off with the main switch The main switch is located on the right side underneath the control panel All three zones are switched on or off together Once on the appliance begins cooling When the door is open the interior lights
48. the energy performance of the unit c amp t e m f necessary shorten the three parts of the air separator m Insert the foam pieces back into the sides 61 Installation m Position the air separator in the center of the appliance door m From below screw the air separator firmly onto the door with the 2 Screws 62 Electrical connection VAN Avoid the risk of electrical shock Plug into a grounded 3 prong outlet Do not move the ground plug Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Improper connection of the equipment grounding conductor may result in electric shock If you are in any doubt as to whether the appliance has been properly grounded have the appliance checked by a qualified electrician or service technician Installation repairs and other work by unqualified persons could be dangerous Before installing the appliance verify that the voltage load and circuit rating information found on the data plate match the household electrical supply If there are any questions regarding the electrical connection of this appliance to the power supply please consult a licensed electrician or call the Miele Technical Service 853 1 800 999 1360 1 800 565 6435 The appliance is supplied with a UL listed 3 wire power cord and NEMA 5
49. u can easily eliminate Possible cause Remedy Rattling clinking The appliance is not level Realign the appliance using a spirit level by raising or lowering the screw feet underneath the appliance The appliance is touching another appliance or piece of furniture Move it away Check all removable items and refit them correctly Drawers baskets or shelves are jiggling or are stuck Bottles or containers are touching Separate them The transport cable clips are still hanging on the back of the appliance Remove the cable clips 30 After sales service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet When contacting the Technical Service department please quote the model and serial number of your appliance given on the data plate inside the appliance MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that un
50. uld be chilled briefly in the refrigerator before serving Remember that wine should always be cooled to slightly lower than the ideal serving temperature as the temperature increases by 1 to 2 as soon as it is poured into a glass Wooden racks For convenient removal and addition of bottles the wooden racks can be pulled out on rails The wooden racks can also be completely removed m Pull out the empty wooden rack along with the rails as far as the stop then lift it up and out m Toreplace the racks set them on the extended rails so that they click into place Be sure that the ventilation slits at the rear of the unit are not blocked They are essential for the unit to operate properly 21 Storing wine Bottle display rack The display rack can only be attached to wooden racks with wide cross ties In the upper temperature zone these are found in the lower position In the lower temperature zones they are found in both the upper and lower position The display rack allows you to display selected bottles so they can be seen even with the door closed It is recommended that the wooden racks always be left in the pre set positions This makes optimal use of the interior space Never stack bottles on the wooden racks Only the bottom most level in each temperature zone can support a stack of bottles remove the m Lay the wine bottles in the display wooden rack
Download Pdf Manuals
Related Search