Home

Miele KFNS 37692 iDE Operating and Installation Instructions

1. m while holding the adjusting bolts in m Drill holes in the door panel and fit place with a screwdriver tighten the screws 43 Make sure the two metal nuts on the appliance doors with a edges are aligned Symbol mene m Close the appliance door and the m Cover strip must be completely cabinet door hidden in the niche and must not protrude Adjusting the position of the door Depth adjustment Z m Loosen screws at the top of the appliance door and screw 44 on the mounting bracket at the bottom By moving the cabinet door create a gap of 1 16 2 mm between the cabinet door and the housing unit 107 Installing the appliance m Tighten all the screws again The following confirms that the appliance is correctly installed The doors close properly The doors do not touch the housing unit The seal at the upper corner of the side with the handle contacts tightly m Replace top cover 49 and click it into place m Replace side covers 4 making sure you hear them click into place 108 109 110 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888
2. settings being adjusted by mistake it is only possible to deactivate the lock Activating and deactivating the safety lock m Tap the settings button b All symbols available for selection will appear in the display and the amp symbol flashes m Tap the OK button to confirm your selection The last selected setting flashes in the display and the lights up 29 Making additional settings aN m By touching the V or A button you can now select whether the safety lock is activated or deactivated G the safety lock is deactivated i the safety lock is activated m Tap the OK button to confirm your selection The selected setting will be adopted and the symbol will flash NA m Tap the settings button to leave the settings mode Otherwise the appliance exits the settings mode automatically after approximately one minute gt The G symbol will appear in the display when the safety lock is activated 30 Temperature unit Celsius or Fahrenheit The temperature can be displayed in either Fahrenheit F or Celsius C The factory default is Fahrenheit F Setting the temperature display to Celsius e m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes f m Touch the buttons for setting the temperature V or A repeatedly until C and F flash in the display m Touch the OK button to confirm your
3. To save energy the SuperCool function can be switched off once a constant temperature of O F 18 C is reached inside the freezer section Check the temperature inside the appliance m Touch the sensor button for the freezer section The freezer section symbol will light up yellow 26 m Touch the SuperCool button so that it is no longer highlighted in yellow The appliance now continues running at normal cooling capacity Temperature and door alarm Your appliance is equipped with a warning system to ensure that temperature increases in the freezer section do not go unnoticed and also prevents energy from being wasted when a door is left open Temperature alarm If the freezer temperature becomes too warm the sensor button of the freezer zone will flash and the alarm symbol Z in the display will flash simultaneously An alarm will also sound The point in time at which the appliance detects a temperature range as too warm depends on the selected temperature The audio and visual signalsare triggered for example when the appliance is turned on and the temperature in a temperature zone deviates greatly from the set temperature when too much warm air flows into the appliance for example when food is being re arranged or taken out when freezing large amounts of food at once when there is a loss of power when the appliance is defective Once the set temperature h
4. Before connecting the water hose for the ice cube maker ensure the water supply is completely turned off The water being used should meet the drinking water standards of the country where the machine is used All devices used for connecting the appliance to the water supply must comply with the current national and local safety regulations in the country in which the appliance is being installed All units and systems used to supply water to the appliance must also comply with the applicable requirements of the respective country The appliance must be connected to a cold water line that is directly connected to the fresh water supply in order to ensure a circulation of the water in the cold water line Avoid using a water line in which the water is allowed to pool This can affect the taste of water and ice cubes withstands the operating pressure fulfills the hygiene regulations The water pressure must be between 22 and 87 psi 1 5 and 6 bar A shut off valve must be provided between the water line and the water supply of the building to ensure that the water supply can be cut off if necessary The water supply should be easily accessible after the machine has been built in Before commissioning the water line needs to be vented by a qualified technician 81 Plumbing The water connection can be found at the back of the appliance The solenoid valve 2 has a 3 4 connection t
5. Caution Risk of damage to the ice cube maker During the operation of the ice cube maker do not interrupt the water supply 83 Electrical connection N Failure to follow these instructions can result in death fire or electrical shock Improper connection of the equipment grounding conductor may result in electric shock If you are in any doubt as to whether the appliance has been properly grounded have the appliance checked by a qualified electrician or service technician Installation repairs and other work by unqualified persons could be dangerous The manufacturer will not be held responsible for damage or injury arising from unauthorized work Before installing the appliance verify that the voltage load and circuit rating information found on the data plate match the household electrical supply To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician 84 N This appliance is equipped with a three prong grounding plug to prevent shock hazards It should be plugged directly into a properly grounded outlet Do not cut or remove the grounding prong from the plug If the plug does not fit the outlet have the proper outlet installed by a licensed electrician Do not
6. amp Ice cube maker is turned off I Ice cube maker is turned on 2 Set the water quantity 3 Set cleaning position for the ice cube tray 4 Rinse the ice cube maker m Touch the OK button to confirm your selection The selected setting is saved and you will hear the ice cube tray moving into a slanted position m Wait until the rotation has stopped before continuing The ice cube maker will then switch off The symbol for the ice cube maker ag will disappear from the display 56 m Remove and clean the ice cube drawer The ice cube tray is not removable and can only be cleaned when in place m Clean the ice cube tray As soon as the ice cube maker is turned on the ice cube tray rotates back to its original position Cleaning and care Before cleaning the appliance m Turn off the appliance The display goes out and cooling is turned off If this does not happen then the safety lock is still activated see Selecting additional settings Deactivating the lock m Unplug the appliance or trip the circuit breaker m Take any food out of the appliance and store it in a cool place m Remove the door shelf bottle shelf from the door m Remove the PerfectFresh Pro zone drawers and the respective drawer lid see Adjusting the interior fittings PerfectFresh Pro zone compartments m Remove the glass plate from the divider panel m Take all removable parts out for cle
7. approx 24 hours if the appliance is full before checking the temperature display as it will take this long for the appliance to reach the temperature If after this amount of time the temperature is too high or too low adjust it again 22 Possible setting values for the temperature The temperature can be selected within the following ranges from 37 F 3 C to 48 F 9 C in the refrigerator section from 5 F 15 C to 15 F 26 C in the freezer section The right temperature Adjusting the temperature in the PerfectFresh Pro zone In the PerfectFresh Pro zone the temperature is maintained between 32 F 0 C and 37 F 3 C However if you would like it to be warmer or colder e g when storing fish you can adjust the temperature slightly The preset temperature in the PerfectFresh Pro zone is 5 lf a setting of between 7 and 4 is selected minus temperatures may be reached thus resulting in food freezing Adjusting the temperature m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes ANG m Touch the buttons for setting the temperature V or A repeatedly until the 1 symbol flashes in the display m Touch the OK button to confirm your selection The last selected setting flashes in the display and the lights up m You can now adjust the temperature in the PerfectFresh Pro zone by touching the
8. The rear stopping bar must be raised to prevent the bottles touching the rear wall The bottle rack has stoppers at the sides to prevent the rack being pulled out unintentionally PerfectFresh Pro zone compartments The compartments in the PerfectFresh Pro zone are on telescopic rails and can be removed for filling emptying or cleaning purposes To make it easier to pull out the drawers remove the bottle shelf from the appliance door m Pull out the drawer as far as it will go m Hold the drawer at the sides towards the back lift it slightly and then pull it out Push the runners back in again to avoid damaging them m Carefully pull out the lid between the compartments slightly and lift it down and out 43 Adjusting the interior fittings Take care when cleaning the appliance that you do not wash the special lubricant out of the telescopic runners Wipe them with a well wrung out damp cloth m To refit the drawer insert the compartment lid from beneath into the holders and push it back into place To replace the drawer m Place the drawer on the fully extended telescopic runners m Push the drawer in until it clicks into place 44 Freezing and storing food Always follow USDA guidelines on food safety WARNING Danger of fire Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended
9. Slide the clips from the back into the ventilation grill until the hooks connect with the plinth m Install the plinth with the inserted ventilation grill Installation information Before installation m Before installation remove the accessories bag containing installation components and accessories from the appliance and remove the sealing strip from the appliance door m Do not remove the following from the back of the appliance The spacers depending on model These ensure the gap required between the back of the appliance and the wall is maintained Depending on model the pouches located in the metal grille heat exchanger They are required for the correct functioning of the appliance The contents are not poisonous or dangerous m Remove any cable clips from the back of the appliance m Check that all parts at the back of the appliance are unhindered Carefully remove any hindrance m Open the appliance door and remove the red safety catch depending on model Spacers on the back If the depth of the unit is less than 21 3 4 553 mm remove the spacers on the back of the appliance in order to be able to push the appliance completely into the recess Removing the spacers may cause the appliance to use mor energy as this reduces the ventilation cross section m Undo the
10. by the manufacturer Maximum freezing capacity To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible the maximum freezing capacity must not be exceeded The maximum freezing capacity for freezing within a 24 hour period is given on the data plate Freezing capacity lbs 24 hrs What happens when you freeze fresh food Fresh food should be frozen as quickly as possible so that the nutritional value of the food its vitamin content appearance and flavor are maintained The longer food is frozen the more water is loses from each individual cell in to the intermediate spaces The cells then shrink During the defrosting process only some of this water is reabsorbed by the cells In practical terms this means that the food loses a substantial amount of liquid which can be seen by the fact that a large pool of water collects around it If food is frozen quickly the cells have less time to lose moisture so they shrink less As there is not so much moisture loss it is easier for the food to reabsorb it during the defrosting process and very little water collects around the defrosted food Storing frozen food When buying frozen food to store in your freezer make sure to check that the packaging is not damaged the expiration date and the temperature at which the frozen food is being stored in the shop The length of time it can be kept is reduced
11. food is being frozen at once m See Freezing and storing food The SuperCool function for the refrigerator is still turned on It will turn itself off automatically after approx 12 hours To save energy you can turn SuperCool off yourself m Press the SuperCool button The SuperCool function for the freezer is still turned on It will turn itself off automatically after approx 30 65 hours You can turn off the SuperCool function earlier to save energy m Press the SuperCool button The compressor runs continuously To save energy the compressor runs at a lower speed but for longer when less cooling is required In this way the running time of the compressor is extended None 62 Frequently asked questions Problem Possible cause Solution The compressor is turning on more frequently and for longer periods The ventilation slits in the cabinetry have been covered or become too dusty m Do not block the ventilation slits m Clean the ventilation slits on a regular basis The doors have been opened too frequently or a large amount of fresh food has been put in at once for storage or freezing m Only open the door when necessary and for as short a time as possible After a while the temperature will return to normal by itself The appliance doors are not closed properly A thick layer of ice may have developed in the f
12. if it has been stored at a temperature warmer than 0 F 18 C m Buy frozen food at the very end of your shopping trip m Place frozen food in the freezer im mediately upon returning home Never re freeze partially or fully defrosted food Defrosted food may only be re frozen after it has been cooked 45 Freezing and storing food Before placing food in the freezer m When freezing more than 4 5 lbs 2 kg of fresh food turn on the SuperCool function some time before placing food in the freezer see Using SuperCool This helps food which is already stored in the freezer to remain frozen Placing food in the freezer The following maximum loading weights must not be exceeded Freezer drawer 55 Ibs 25 kg Glass plate 77 Ibs 35 kg Unfrozen food should not touch frozen food as this will cause frozen food to begin to thaw m When placing items in the freezer ensure that the packaging and containers are dry to prevent them from sticking together when frozen Freezing small amounts of food Place the food in the upper freezer drawers m Place the food flat in the bottom of the freezer drawer so that it freezes through to the core as quickly as possible 46 When removing the upper freezer drawers please note The bottom drawer must always remain in the appliance When placing food in the drawers make sure that you do not block the ventilation cross sections in the back wall
13. is plugged in and turned on AN m Touch the On Off button The power supply symbol disappears and the appliance starts to cool The sensor buttons for cooling zones that can be selected appear in the control panel op ee Refrigerator The refrigerator section sensor button is highlighted yellow and the current temperature in this section appears in the display Freezer When the refrigerator door is opened the interior lighting comes on and the LED lighting on the adjustable shelves becomes brighter until it reaches its maximum brightness When the freezer section is turned on for the first time the sensor button for this section and the alarm symbol A flash until the set temperature is reached The button lights up constantly and the alarm symbol goes out when the temperature set for the freezer section is reached To enable the temperature to get sufficiently cold inside the appliance allow the appliance to run for a few hours before placing food in it Do not place food in the freezer section until the temperature is cold enough at least O F 18 C Turning the appliance on and off Individual settings can be set for each cooling zone m Touch the sensor button for the zone in which you want to adjust the settings The selected sensor button appears yellow The SuperCool function can be selected or the temperature can be adjusted for the refrigerator or freezer
14. light illuminates on the ice cube maker An ice cube tray where ice cubes are produced is integrated in the ice cube maker The ice cube tray automatically empties into the drawer as soon as ice cubes are produced 48 Rinse the ice cube maker along with the water pipes before installation if the ice cube maker has not been used for a longer period of time during regular daily use at least once a month to remove ice residues from the system this will avoid a blockage in the water pipes and before the ice cube maker is to be turned off for a long time See Cleaning and care Rinse the ice cube maker on how to select this function Ensure the ice cube drawer is empty before turning on the ice cube maker Making ice cubes Turning the ice cube maker On Off m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes m Touch the buttons for setting the temperature V or A repeatedly until the symbol for the ice cube maker ag flashes in the display m Touch the OK button to confirm your selection m Touch the V and A buttons to set the ice cube maker 0 Ice cube maker is turned off i Ice cube maker is turned on m Touch the OK button to confirm your selection The selected setting will be adopted m Touch the settings button to leave settings mode or m close the appliance door The electronics
15. no oil or grease leaks onto the plastic parts of the appliance This can cause the plastic to crack and break Food must not touch the back wall of the appliance as it may freeze to wall To allow air to circulate efficiently do not pack food too closely together in the refrigerator Make sure that the fan at the back of the appliance is not covered This is important for the refrigerator s cooling capacity 37 Storing food in the PerfectFresh Pro zone Due to the optimum storage conditions in the PerfectFresh Pro zone for fruit vegetables fish meat and dairy products food remains fresh for longer and flavor and vitamins are retained The optimum storage temperature for fresh food which is not sensitive to the cold is 82 37 F 0 3 C This is the temperature range which is automatically maintained in the PerfectFresh Pro zone Food which is not sensitive to cold can be stored in the PerfectFresh Pro zone at this temperature without loss of freshness for considerably longer than in a stan dard refrigerator as the deterioration process is decelerated at this temperature The humidity level in the PerfectFresh Pro zone can also be regulated to provide the correct conditions for food stored inside it An increase in the humidity level ensures that food retains its own moisture and does not dry out so quickly Therefore such food will remain firm and fresh for longer Remember that food has to be in go
16. removable items are jiggling or are stuck and refit them correctly Bottles or containers are Separate them touching The transport cord clips are Remove the cord clips still hanging on the back of the appliance 73 Lead free certificate j This product is tested and certified by WQA against ORDO902 for California lead free compliance Miele amp Cie KG Carl Miele Strake 29 D 33332 G tersloh 74 Service Warranty In the event of a fault which you cannot correct yourself please contact your Miele dealer or Miele Technical Service See back cover of the this manual contact details When contacting Miele Technical Ser vice please quote the model and serial number of your appliance This information is given on the data plate inside your appliance Warranty For additional information please refer to your warranty booklet See the end of these operating and installation instructions for this telephone number 75 Information for dealers showrooms Demo mode I This appliance can be presented in retails stores and in showrooms with the help of the Demo mode The controls and lighting will still work but the compressor will not operate Switching on the Demo mode AN m Switch the appliance off by tapping the On Off button If this does not work the safety lock is still activated The temperature will go out and the mains
17. rinsing the ice cube maker There are unsealed packages in the freezer section Ice can absorb the taste and smell of unsealed food m Store only sealed food in the freezer section The ice cube drawer is dirty m f necessary clean the ice cube drawer 72 Noises Normal noises What causes them Brrrrr This noise may get louder for brief periods when the motor kicks on Blub blub A gurgling noise can be heard when the refrigerant circulates through the pipes Click Clicking sounds occur whenever the thermostat turns the motor on or off Sssrrrrr In multi section and frost free appliances the movement of air circulating through the appliance can sometimes just barely be heard In appliances with a water tank a humming noise can be heard when the water pump is running Crack A cracking noise can be heard when the appliance materials expand Keep in mind that a certain amount of noise is unavoidable from the compressor and the refrigerant circulating through the system Noises that you Possible cause Solution can easily eliminate Rattling clinking The appliance is not level Realign the appliance using a level by raising or lowering the screw feet underneath the appliance The appliance is touching Move it away another appliance or piece of furniture Drawers baskets or shelves Check all
18. screw and remove the spacers 89 Installation dimensions E 378 2200em 21978 2500 mm lt K 1 40 mm iS 3 N V o N co Vl Leg y 278 2 gt 200 ml i Before installation ensure the building in niche is the correct size The specified ventilation cross sections must be adhered to in order to ensure the correct functioning of the appliance Niche height mm Freezer section mm A B KFNS 37692 iDE 69 3 4 70 3 8 27 3 8 1772 1788 mm 695 mm 90 Adjusting the door hinge The door hinges are factory set so that the door can be opened wide However if the opening angle of the door needs to be limited for any reason the hinge can be adjusted to accommodate this If for instance when it is opened the appliance door would hit an adjacent wall you should limit the opening angle of the appliance door to 90 m Insert the limit pins provided into the hinges from above This will limit the opening angle of the appliance door to 90 91 Changing the door hinging m Open both appliance doors Always change the door hinging with the he ees ot anaiher Seer m Remove the shelves bottle shelf from the appliance door The appliance is supplied right hand hinged If left hand hinging is required the hinges must be changed You will need the following tools for
19. section Please refer to the relevant section in the manual for more information If another cooling zone is selected the settings for the previously selected zone will remain as they were 18 Turning the appliance off AN m Touch the On Off button If this does not work the safety lock is activated The temperature will go out and the power supply symbol will appear The interior lighting goes out and the cooling is turned off Turning off the refrigerator section separately The refrigerator section can be turned off without having to turn off the freezer section This is useful e g while on hol iday Cxxx m Touch the sensor button for the refrigerator section until it is no longer illuminated Dashes will temporarily appear in the display Turning the appliance on and off Turning the refrigerator section back on again The refrigerator section can be turned on separately gt D Cix m Touch the button for the refrigerator section until it lights up yellow again The temperature display for the refrigerator section lights up The refrigerator section starts to cool and the interior lighting comes on when the door is opened Turning the appliance off when in Sabbath mode You can turn the appliance off at any time AN m Touch the On Off button The temperature display goes out and the amp symbol electrical connection appears The interior light goes out and
20. section is too high m Select a lower temperature The a9 symbol flashes and the indicator light on the ice cube maker flashes when the ice cube maker is turned on The water supply line is not open m Open the water intake The a9 and A symbols flash The indicator light on the ice cube maker also flashes The is a fault with the ice cube maker m Contact Miele Technical Service 71 Frequently asked questions Problems with the ice cube maker Problem Possible cause Solution The ice cube maker is producing only small ice cubes The size of ice cubes produced depends on the water pressure and water intake time set on the ice cube maker In this case the water pressure is low m To make larger ice cubes the incoming water volume of the ice cube maker must be extended The ice cubes have an unpleasant odor or flavor The ice cube maker has been on for a long time and needs to be cleaned regularly m Rinse the ice cube maker and water supply regularly see Cleaning and care rinsing the ice cube maker The ice cube maker is seldom used If you do not use it very often ice cubes that are stored for a long period can absorb the taste and smell of other items m Empty the ice cube drawer if you are not going to use the ice cube maker for a long time Rinse the ice cube maker and water supply regularly see Cleaning and care
21. surface m Secure the side cover to the bracket on the opposite side of the hinge m Turn the door over and attach the handle if required m Using a pencil lightly mark a line down the center of the inside of the panel m Hang the fixing bracket with the fitting aids onto the inside of the cabinet door Align the bracket centrally m Attach the mounting bracket securely using at least 6 short particle board screws Drill holes in the cabinet door if necessary m Pull the installation aids upwards to remove them Turn them around and fit them into the middle slots on the bracket for safe keeping 105 Installing the appliance m Open the appliance door Adjusting the position of the door 3mm 1 8 13mm 1 2 lt lt m Hang the door panel on the threaded Side adjustments X bolts m Adjust the door panel m Screw the nuts loosely onto bolts Height adjustment Y m Close the door and check the distance between the door and neighboring cabinet doors The gaps should be even m Tighten the nuts with a wrench A gap of 3 8 8 mm is factory set between the appliance door and the bracket This must only be adjusted within its permitted range 106 Installing the appliance
22. the Temperature PerfectFresh Pro zone Mi Sabbath Mode For turning Sabbath mode on and off G Power Supply Confirms that the appliance is connected to the electricity supply when it is not turned on flashes when there is a power cut A Alarm Illuminates when the door alarm is activated flashes in case of a temperature alarm power failure and additional fault messages ja Demo Mode For turning off Demo mode only visible when Demo mode is active Guide to the appliance 12 Control panel Fan 3 Egg tray Door shelf Shelf Shelf with lighting FlexiLight Bottle shelf PerfectFresh Pro zone interior lighting PerfectFresh Pro zone dry compartment Condensate channel and drain hole 0 Moisture level control in the humidity controlled compartment 4 PerfectFresh Pro zone humidity controlled compartment Ice cube drawer with automatic ice cube maker a3 Freezer drawers Guide to the appliance Optional accessories Stainless steel maintenance Each application of the Miele stainless steel conditioner forms a water and dirt repellent protective coating It gently removes water marks fingerprints and other dirt for a un
23. the cooling is turned off When you turn the appliance back on the Sabbath mode is off Turning off for longer periods of time If the appliance is not needed for a longer period of time m turn the appliance off m unplug the power cord or trip the circuit breaker m empty the ice cube drawer m close the water shut off valve If you are not using the appliance or refrigerator section if it has been turned off separately for an extended period of time m clean the appliance refrigerator section and m leave the appliance doors refrigerator door slightly ajar to avoid the build up of odors If during a long absence the the appliance refrigerator section is turned off but not cleaned out and the doors are left shut there is a danger of mold and odors building up inside the appliance The right temperature It is very important to set the correct temperature for storing food in the appliance Bacteria will cause food which is not stored at the correct temperature to deteriorate rapidly The temperature in the appliance will rise for the following reasons if you open the door frequently or keep it open too long if you put too much food in it if you put food in it that is too warm if the room temperature is too high The appliance is designed for use within a certain climate range room temperature range and should not be used outside this range n the refrigerator sect
24. the audio alarm If the audio alarm bothers you it can be silenced m Touch the button to turn off the door alarm The audio alarm will stop The alarm symbolA will continue to be displayed until the door is closed Making additional settings Certain appliance settings can only be selected in the settings mode While you are in settings mode the door alarm and any other fault messages are suppressed automatically but the alarm symbol Z lights up in the display Available settings Q Activating and deactivating the safety lock c Select the temperature unit F Celsius or Fahrenheit Switching ice cube maker on off set amount of water rinse ice cube maker set ice cube tray cleaning position dS Switching acoustic signals on off Changing the brightness of the display F Adjusting the temperature in the PerfectFresh Pro zone oe oe Switching Sabbath mode on off All setting options for the ice cube maker are described in Making ice cubes and Cleaning and care Adjusting the temperature in the PerfectFresh Pro zone is described in The correct temperature chapter All other setting options are described below Safety lock amp The safety lock can be activated to prevent the appliance being switched off by mistake the temperature being changed by mistake unwanted selection of SuperCool and SuperFreeze
25. use extension cords or ungrounded two prong adapters Connect this appliance to a 110 120 VAC 60 Hz and 15 amp 20 amp for side by side circuit with a circuit breaker or fuse This appliance must be grounded according to local or national codes Electrical connection The appliance must be connected to an electrical outlet that is properly grounded The electrical installation must comply with the applicable electrical code The plug must be easily accessible and not concealed behind the appliance so that the appliance can quickly be disconnected from the electricity supply in an emergency In addition no other appliances should be plugged into a socket located directly behind this appliance The power cord must not come into contact with the back of the appliance as they could be damaged by vibrations from the appliance This may result in a short circuit Do not use an extension cord to connect the appliance to the power supply Extension cords do not guarantee the required safety of the appliance e g they pose a danger of overheating Do not connect the appliance to stand alone inverters such as those used with an autonomous energy source e g solar power systems Otherwise when the appliance is switched on peak loads in the system can cause the safety shutdown mechanism to be triggered This can damage electronic units In addition the appliance must not be used with energy saving devices w
26. 0 0 eee 91 Changing the door hinging 0 0 0c cee 92 Installing the appliance 0 0 00 00 ee 96 Installing the custom door front s sssaaa 103 Adjusting the position of the door 2 aaa aaa 106 Contact details 0000 00 2 ee 114 IMPORTANT SAFETY INSTRUCTIONS When using the appliance follow basic safety precautions including the following Read all instructions before installation and use to prevent accidents and machine damage This appliance conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property They contain important notes on installation safety use and maintenance Miele cannot be held iable for non compliance with these instructions Keep these instructions in a safe place and pass them on to any future owner Correct use B This appliance is intended for use in domestic households and similar residential environments This appliance is not intended for outdoor use P Use this appliance only under normal household conditions for cooling and storage of food storage of frozen foods for freezing fresh foods and for preparation of ice Any other usage is at the owner s risk and could be dangerous gt This appliance is not suitable for storing and keeping cool medicines blood plasma laboratory preparations or other such materials or products Incorrect use of the appliance for su
27. 586 8056 TechnicalService mieleusa com Miele www miele shop com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 Fax 905 532 2290 www miele ca professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercare miele ca general and technical enquries ea KFNS 37692 iDE CE en US CA M Nr 10 160 250 00
28. K button to confirm your selection The selected setting will be adopted m Touch the settings button to leave settings mode or m close the appliance door The electronics will otherwise switch to normal operation after one minute Making ice cubes Turning the ice cube maker On Off with the On Off button m Open the ice cube drawer slightly V m Press and hold the On Off button on the ice cube maker until the indicator light comes on The symbol for the ice cube maker a9 will appear in the display The ice cube maker is now on until the indicator light goes out The symbol for the ice cube maker g9 will disappear from the display The ice cube maker is now off m Close the ice cube drawer 51 Automatic defrosting WARNING Risk of injury and damage Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer Refrigerator section and PerfectFresh Pro zone The refrigerator section and the PerfectFresh Pro zone defrost automatically Condensate and frost can build up on Freezer section The appliance is equipped with a NoFrost system for automatic defrosting as needed The moisture generated in the appliance collects on the condenser and is automatically defrosted and evaporates periodically This automatic defrosting system enables the freezer to remain permanently ice free but the foo
29. This may in turn cause the compressor to be damaged Air at the back of the appliance gets warm The appliance housing unit must be constructed to allow sufficient space for ventilation see Installation dimensions Air intake occurs via the plinth at the bottom of the appliance and the air escapes at the top at the rear of the housing unit A ventilation gap of at least 1 5 8 40 mm depth must be provided behind the appliance for air to circulate The ventilation grilles in the plinth housing unit and above the appliance must amount to at least 78 3 4 to ensure that air can circulate without obstruction Important The appliance uses less energy the larger the ventilation grille The ventilation grilles must not be blocked or covered in any way They also need to be dusted cleaned on a regular basis 87 Installation information Top ventilation grille The ventilation grille at the top of the appliance can be constructed in different ways directly above the appliance with a ventilation grille free airflow of at least 78 3 4 in between the housing unit and the ceiling 3 through a suspended ceiling 88 Ventilation grill During construction the ventilation grill can be built in m Cut an opening into the plinth as shown in the illustration above m Place the ventilation grill into the cut out m
30. V or A button You can choose from settings 7 to 9 i lowest temperature 3 highest temperature m Touch the OK button to confirm your selection The selected setting will be adopted and the t symbol will flash w m Touch the settings button to leave the settings mode Otherwise the appliance will exit the settings mode automatically after approximately one minute gt The newly set temperature for the PerfectFresh Pro zone will gradually be reached 23 SuperCool The SuperCool function inthe Turning off SuperCool refrigerator The SuperCool function turns off The SuperCool function can be used to automatically after approx 12 hours rapidly reduce the temperature in the The appliance then operates at normal refrigerator section to its lowest setting Cooling capacity depending on the room temperature To save energy the SuperCool function can be turned off once food and drinks Turning on SuperCool are sufficiently chilled SuperCool is particularly recommended for the fast chilling of large amounts of PT xX fresh food or drink GD a m Select the sensor button for the refrigerator zone The refrigerator section symbol will m Select the sensor button for the light up yellow refrigerator zone The refrigerator section symbol will light up yellow m Touch the SuperCool button so that it is no longer highlighted yellow The appliance now continues m Touch the SuperCoo but
31. aL Miele Z l miir For turning the entire appliance on and off Optical interface for Service use only For selecting the refrigerator or freezer section On Off button for the SuperCool functions 10 OK A i i if T For setting the temperature V for colder selection button in settings mode For confirming a selection OK button For setting the temperature A for warmer selection button in setting mode For accessing or leaving settings mode For turning the temperature and door alarms off Display with temperature and symbols symbols only visible in settings mode in the event of an alarm message see table for explanation of symbols Guide to the appliance Explanation of symbols Symbol Meaning Function a Safety Lock Prevents the user from unintentionally turning off the appliance adjusting the temperature turning on the SuperCool functions or entering settings a9 Ice Cube Maker Turning the ice cube maker on and off setting the water quantity rinsing the ice cube maker setting the cleaning position of the ice cube tray flashes when there is a fault with the ice cube maker ds Acoustic Signals Selection options for the keypad tone and the door and temperature alarm tones Display Brightness For adjusting the brightness of the display Settings Et PerfectFresh Pro Adjusting the temperature in
32. account when making sure there is a gap all round of 1 5 8 42 mm m Pull the appliance forward the appropriate amount to suit the installed dimensions The hinges and covers will now be positioned to suit the dimensions Tip Remove the door fittings This will ensure that the door is flush with the surrounding kitchen unit cabinet doors m 48 Align the appliance on both sides by altering the adjustable feet using the wrench supplied If the all round gap of 1 5 8 42 mm is not maintained between the appliance housing and the front edge of the housing unit side wall the door may not shut properly This can cause ice to build up condensate to accumulate and lead to faults in the appliance These can all lead to increased energy consumption Installing the appliance Securing the appliance in the niche m Push the hinged side of the appliance to the cabinet wall m Screw the particleboard screws through the hinge plates at the top bottom and then in the middle to secure the appliance to the housing unit m Push the loose bracket against the cabinet wall Secure mounting bracket to the housing unit side wall with screw 49 Drill holes in the housing unit side walls if necessary Secure bracket to the housing unit side walls using screws 9 Drill holes in the housing unit side walls if necessary Attention Push the protruding bracket using yo
33. aker the ice cube maker and the water pipes will automatically be rinsed The ice cube tray will turn to the cleaning position so that it can be dried by hand The water is collected in the ice cube drawer 54 Ensure the ice cube drawer is empty before selecting the Rinse the ice cube maker setting The water will otherwise flow onto the contents of the drawer Rinse the ice cube maker can only be selected when the ice cube maker is switched on gt ANS m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes m Touch the buttons for setting the temperature V or A repeatedly until the symbol for the ice cube maker ag flashes in the display m Touch the OK button to confirm your selection m The required setting can be selected by touching the X and Y buttons 0 Ice cube maker is switched off i Ice cube maker is switched on 2 Set the water quantity 3 Set cleaning position for the ice cube tray 4 Rinse the ice cube maker Cleaning and care m Touch the OK button to confirm your selection The selected setting will be saved The ice cube maker symbol g9 will flash in the display and the indicator light will flash on the ice cube maker as long as the ice cube maker is being rinsed You will hear the ice cube tray turning to a slanted position m Wait until the rotation has stopped before continuing T
34. aning Adjustable shelf Adjustable shelf with lighting The stainless steel strio with LED lighting and the stainless steel strips on the shelves are not dishwasher safe The stainless steel strio with LED lighting on the shelf must not be immersed in water Proceed as follows to remove the stainless steel strio with LED lighting or the stainless steel strip and rear protective strip m Place the shelf on a soft surface e g towel with the top side facing downwards Stainless steel strip with LED lighting Attention Always loosen the side without the contacts metal discs for the LED lighting first 57 Cleaning and care m Take hold of the rear part of the plastic edging on the left hand side of the stainless steel trim 1 Remove the plastic edging from the adjustable shelf and 2 remove the trim at the same time The opposite side will now also come loose m 3 Remove the protective strip at the back m After cleaning reattach the stainless steel strip and the protective strip in reverse order 58 Door shelves and bottle shelves The stainless steel facia panels on the door shelves and bottle shelves are not dishwasher safe To remove the stainless steel plinths proceed as follows m Place the door bottle shelf with the front side on the work surface m Remove one end of the plinth and pull it off the shelf Then remove the entire stainless steel plinth from the shelf
35. as been reached in the freezer section the alarm turns off and the alarm symbol N disappears The freezer section button is once again constantly illuminated However if the temperature in the freezer remains above O F 18 C for a long time check that the frozen food has not started to defrost If it has check that the food is safe to use and if it is then use it as soon as possible or cook it before freezing it again Turning off the audio alarm If the audio alarm bothers you it can be silenced m Touch the button to turn off the temperature alarm The audio alarm is silenced Both the freezer zone button on the control panel and the N symbol in the display will continue to flash until the alarm status is ended 27 Temperature and door alarm Door alarm An alarm will sound if the door is left open for too long The alarm symbol Z will light up The amount of time until the door alarm is triggered depends on the setting selected and can be either 2 minutes factory default or 4 minutes However the door alarm can also be switched off see Additional settings Acoustic signals As soon as the door is closed the audio alarm is silenced and the alarm symbol Z will disappear from the display If no audio alarm sounds even though a door alarm is available then the audio alarm has been turned off in settings mode see Additional settings Acoustic signals 28 Turning off
36. ch purposes can cause deterioration of the items stored The appliance is not suitable for use in areas where there is a risk of explosion Miele will not be held liable for damage resulting from incorrect or improper use or operation P gt Persons who lack physical sensory or metal abilities or experience with the machine should not use it without supervision or instruction by a responsible person Safety with children P gt Children should be supervised in the vicinity of the appliance P Children ages eight and up may only use the appliance oven without supervision if they have been shown how to use it in a safe manner and if they are able to recognize and understand the potential risks of improper use gt Children must not clean or service the appliance unless they are under supervision P gt Children should be supervised when they are near the appliance This appliance is not a toy To avoid the risk of injury do not allow children to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen IMPORTANT SAFETY INSTRUCTIONS P Ensure that any packing material is disposed of safely and kept out of the reach of children Danger of suffocation Technical safety gt The coolant system is tested for leaks gt This appliance contains the coolant isobutane R600a a natural gas which is environme
37. changing the door hinging m Pull off the covers and 92 Changing the door hinging m Slightly loosen the screws and m Remove the screws completely on the hinges j m Place the mounting bracket on the m Slide the doors and outwards opposite side and loosely screw in and take them off their hinges the screws m Remove screws completely and loosely screw them in on the opposite side If you had inserted pins into the hinges to limit the door s opening angle m Remove the locking pins from the top of the hinges 93 Changing the door hinging Carry out the following steps on both doors Unscrew the door closing dampers Caution When removed from the unit the soft close mechanism snaps shut Risk of injury m Place the door with the outer side downwards on a stable surface m Using a screwdriver remove the ball joint and screw it into the adjacent hole m Now turn over the appliance door so that outer side faces upwards hinges remain open Do not close the hinges Danger of injury m Remove the soft close mechanism from the ball joint m Unscrew the mount and pull the soft close mechanism towards you to remove it m Remove the screws m Place each hinge in the corner diagonally opposite from its original position 94 Changing the door hinging Fastenin
38. connection symbol will appear 76 aN m Place your finger on the V button and hold it there O 2 m At the same time briefly tap the On Off button without letting go of the V button m Keep your finger on the V button until the lf symbol appears in the display m Then take your finger off the V button Demo mode is switched on and the i symbol is illuminated in the display Information for dealers showrooms Switching off Demo mode The IH is illuminated in the display m Tap the settings button All symbols available for selection will appear in the display and the amp symbol flashes f m Tap the buttons for setting the temperature V or A repeatedly until the J symbol flashes in the display m Tap the OK button to confirm your selection i flashes in the display Demo mode is active and the If symbol is illuminated m Tap the V or A button so that amp appears in the display Demo mode is inactive m Tap the OK button to confirm your selection The selected setting will be adopted and the symbol will flash i m Tap the settings button to leave the settings mode Otherwise the appliance exits the settings mode automatically after approximately one minute gt The Demo mode is switched off and the E symbol disappears 77 78 Scat Installation Instructions Information is subject to change Please refer to our website to obtain the mo
39. d stored in the freezer will not defrost the back wall of the refrigerator section and the PerfectFresh Pro zone while in use You do not need to remove this as it will defrost and evaporate automatically with the warmth generated by the appliance The condensate is drained away through a channel and drain hole then fed into an evaporation system at the back of the appliance It is important to keep the condensate channel and drain hole clean and free of blockages so that the condensate can flow away properly 52 Cleaning and care WARNING Danger of electric shock Unplug refrigerator or disconnect power Danger of fire Do not damage the refrigerant circuit Do not let water get into the electronic unit or the lighting or on the metal contacts in the left hand shelf support Cleaning water must not get into the drain hole Do not use a steam cleaning apparatus to clean the appliance Steam could reach the electrical components and cause a short circuit The data plate located inside the appliance must not be removed It contains information which is required in the event of a service call Information regarding cleaning agents To better maintain your appliance avoid the following cleaning products containing soda ammonia acid or chloride lime removers abrasive cleaning products such as scouring powder scouring liquid or pumice stones cleaners conta
40. e salads dairy products such as yogurt cheese cream etc any type of food can in fact be stored in this compartment as long as it is packaged The low temperature in the dry compartment is its most distinctive feature The humidity level is similar to that in a conventional refrigerator Please note that foods rich in protein deteriorate faster than others Always keep these foods covered or wrapped Humidity controlled compartment 6 66 666 Low humidity 6 When this setting is used the humidity controlled compartment becomes a dry compartment The slide control opens the narrow openings in the compartment so that moisture is able to escape see Dry compartment 6 High humidity level 66 666 Both settings 66 666 are suitable for storing fruit and vegetables If you are storing a large quantity of fruit and vegetables in the humidity controlled compartment the 66 setting is recommended the slide control partially closes the openings to the compartment so that a portion of the humidity is retained If you are storing a small quantity of fruit and vegetables in the humidity controlled compartment the 666 setting is recommended the slide control completely closes the openings to the compartment so that all of the humidity is retained Tip If the humidity level is too high and a larger amount of moisture collects in the compartment select 66 If the humidity leve
41. e LED lighting on the stainless steel strip is faulty m Replace the stainless steel strip with LED lighting It can be ordered from Miele Technical Ser vice or your dealer Do not remove the light cover If the cover is damaged or has been removed as a result of being damaged use caution Never use optical instruments magnifying glass or similar devices to view the lighting as it contains lasers class 1M laser radiation There are live electrical components under the light cover Risk of injury and damage 67 Frequently asked questions Interior lighting Problem Possible cause Solution The LED lighting on one of the shelves does not work The shelf is not sitting correctly in the shelf supports m Push in the shelf until it clicks into position The LED lighting on the shelves does not work Liquid has come into contact with the LED lighting on a shelf or the metal discs contacts in the left hand shelf supports A safety cut out turns the interior lighting off m Wipe the stainless steel strio with LED lighting with a damp cloth and dry it with a soft cloth or let it dry outside the appliance Clean the metal discs contacts in the same way Ensure that the contacts are clean and dry before refitting the shelves with LED lighting m Push in the shelf until it clicks into position m Close the appliance door When the door is opened again t
42. e appliance Consult a qualified electrician if in any doubt P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician P gt If the power cord is damaged it must be replaced by a Miele authorized technician in order to protect the user from harm gt Do not connect the appliance to the electrical supply with a power bar or extension cord These are a fire hazard and do not guarantee the required safety of the appliance IMPORTANT SAFETY INSTRUCTIONS gt Do not use the appliance in areas where there may be moisture or splashing water e g garages laundry rooms etc Moisture can reach the electrical components and cause a short circuit B This appliance is not to be used in non stationary locations such as ships gt Do not use a damaged appliance It could be dangerous Check the appliance for visible signs of damage P To ensure safe operation use the appliance only when it is installed gt The appliance must be disconnected from the electrical supply during installation maintenance and repair work and installation work on the water connection The appliance is only completely iso
43. e is a fault m Contact Miele Technical Service The ag symbol flashes and the indicator light on the ice cube maker flashes when the ice cube maker is turned on The water supply line is not open m Open the water intake The a9 and A symbols flash The indicator light on the ice cube maker also flashes The is a fault with the ice cube maker m Contact Miele Technical Service The alarm symbol A lights up in the display together with a refrigerator section button and an acoustic alarm can be heard The door alarm has been activated m Close the appliance door The alarm symbol A will go out and the acoustic alarm will stop 65 Frequently asked questions Indication in the display Problem Possible cause Solution The alarm symbol Z and a refrigerator section sensor button are flashing in the display The affected refrigerator section is warmer or colder than the set temperature for example because the door being opened too frequently alarge quantity of fresh food has been placed in the freezer at once without turning on the SuperCool function there has been a lengthy interruption of the power supply m Remedy the alarm The alarm symbol Z will disappear and the button for the affected refrigerator section will light up constantly again The acoustic alarm will stop Depending on the temperature check whet
44. ect the correct PerfectFresh Pro compartment and the appropriate position of the slide control for the humidity controlled compartment low or high humidity m An increased humidity level 66 666 in the humidity controlled compartment is achieved through the moisture contained within the food being stored i e the more food the more moisture there is If too much moisture collects in the compartment on the 666 setting and this is affecting the food select 66 Otherwise remove the condensate with a cloth If the humidity level is too high despite the 666 setting being selected wrap the food in air tight packaging m f you think that the temperature in the PerfectFresh Pro zone is not correct try adjusting it slightly by 34 35 F 1 2 C via the refrigerator section temperature control To avoid frost damage to food a higher temperature must be set if ice crystals begin to form on the bottom of the PerfectFresh Pro zone 41 Adjusting the interior fittings Adjusting the door shelf bottle shelf m Lift up the door shelf bottle shelf and pull it forward to remove it m Place the door shelf bottle shelf at any position again Make sure that it is properly and secure pushed back into position Adjusting the bottle holder The bottle holder can be moved left or right thus creating more room for drink cartons The bottle holder can be removed completely e g for cleaning m Lif
45. ee Miele Operating and Installation Instructions Fridge Freezer Combination To prevent accidents and damage to the appliance you must read all instructions supplied before installing for using the appliance en US CA M Nr 10 160 250 Contents IMPORTANT SAFETY INSTRUCTIONS 220020055 5 Guide to the appliance 0 00 00 10 Optional accessorie vcs cece en te pn rA canoe nadaadeeead ewe adas nes 13 How to save energy 6 0 eee 14 Turning the appliance on and off 00 00 16 Operating the appliance 0 00 cts 17 Tuning the appllanCe OM sei pesei iei Aa gh add Shae wd bbe eA dR edged 17 Turning the appliance off 0 0 0 0 0 eae 18 Turning off the refrigerator section separately 000020005 18 Turning the refrigerator section back on again 0 0 0 cee 19 Turning the appliance off when in Sabbath mode 0 0000 ee 19 Turning off for longer periods of time 0 0 0c eee 19 The right temperature 6 00 20 in the refrigerator section and in the PerfectFresh Pro zone 20 Automatic cold air circulation DynaCool n a aanas aaaea 20 8 in INEMECZEr SECHON 9 2 2544 454 00 bi riri r EEEE a eeeea ENSERES 20 Temperature display i004 toad Shed bet tweed de bab bod bebe hha a ees 21 Setting the temperature for the refrigerator and freezer 0 0 00 ee 21 Adjusting the temperature in the PerfectFr
46. efore inserting the adjustable shelf with lighting Push in the shelf until it audibly locks into place Only in this way can the lighting work m Connect the appliance again and turn it on m Turn on the SuperCool function in the freezer to cool it down quickly m Turn on the SuperCool function in the refrigerator so it can cool down quickly m Place food in the refrigerator section and close the door m Once the temperature in the freezer section is cold enough you can place the food in the freezer drawers and return the drawers to the freezer m As soon as the freezer section reaches a constant temperature of at least O F 18 C press the SuperCool button to turn off the function Frequently asked questions With the aid of the following guide minor problems can be corrected without a ser vice call If having followed the suggestions below you still cannot resolve the problem please contact Miele Technical Service To prevent cold from escaping open the appliance doors as little as possible until the malfunction has been corrected Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage and may void the warranty Problem Possible cause Solution The appliance does not get cold the interior lightning does not come on when the door open
47. ep an even temperature when the fan is running When DynamicCooling is turned on the difference between the various zones is less pronounced 36 Warmest area The warmest area in the refrigerator section is in the top section of the door Use this for storing butter so that it remains spreadable and cheese so that it retains its flavor Coldest area The coldest area in the refrigerator section is directly above the dividing plate of the PerfectFresh Pro zone and against the rear wall However inside the PerfectFresh Pro zone is even colder Use these areas in the refrigerator section and in the PerfectFresh Pro zone for all delicate and highly perishable food e g fish meat poultry cold cuts ready made meals dishes or baked goods containing eggs or cream fresh doughs raw milk cheese and other raw milk products pre packed vegetables and other fresh food whose best before date requires storage at a temperature of at least 39 F 4 C Storing food in the refrigerator section WARNING Danger of fire Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended by the manufacturer Do not store explosive materials in the appliance or any products containing propellants e g spray cans Danger of explosion If storing fatty or greasy foods in the appliance or the appliance door make sure that
48. esh Pro zone 00005 23 SuperCool enera e a a kaaa GO e aod Ee eee des 24 The SuperCool function in the refrigerator 0 2 0 0 eee 24 The SuperCool function in the freezer ees 25 Temperature and door alarm 000s 27 temperature alan wiih Se ood ehh AGL RES Eade hee AE OSs 27 DOOr Alans sasereg ee eee Rog hed rede oaa Hae scl ee ea Mayes 28 Making additional settings 0 0 0 29 aie MOCK el a3 eet Paes ee Bae Sooo Bh aah ae eee a aes 29 Temperature unit Celsius or Fahrenheit 0 00 0 00000 30 Acoustic signals SS erei ae sit aidaa cad ata es heme AE pee queldla eda 32 Display brightness Or eee eee 33 Sabba thi mode Ne on24 2h eho edelered atudewed herds hig seas ben yao 34 Storing food in the refrigerator section 00004 36 VAlOUS COOUING ZOMESaicicin aa win icaie hoop EA ich MaMa REA E E EE ERA 36 Storing food in the PerfectFresh Pro zone 0005 38 Dry COMPANIMO hh E e sers opiren an eani ance teint pened oh aa Sn aM i 39 Humidity controlled compartment 6 66 666 0 0 020020005 39 LON NUMIA E o ete dee 2 aed attr dat iaa e AE tia eine ate goatee eet ace 39 Contents High humidity level 66 606 0 0 0 0 00 0 0 eee 39 Adjusting the interior fittings 0 0 0 0 eee ee 42 Adjusting the door shelf bottle shelf 0 00 0 cee 42 Adjusting the bottle holder 0 0 00 02 0000 eee 42 Adjustable s
49. ew hours to reach the temperature required and for this temperature to then be shown as a constant temperature in the display If the temperature in the freezer section remains above O F 18 C for along time check that the frozen food has not started to defrost If it has check that the food is safe to use and if it is then use it as soon as possible Setting the temperature for the refrigerator and freezer The temperatures for the refrigerator section and the freezer section are set separately co m Select the refrigerator or the freezer section m Use the two buttons underneath the display to set the temperature By touching the button the temperature will get colder the temperature will get warmer While the temperature is being set the temperature value will flash 21 The right temperature When you touch the buttons you will see the following changes in the display When first touched The last temperature selected flashes Each subsequent touch of the button The temperature value adjusts in 1 steps Keeping your finger on the button The temperature changes continuously Approximately 5 seconds after you release the button the actual temperature value in the appliance will be displayed or m Touch the OK button to confirm your selection When you have adjusted the temperature wait for approx 6 hours if the appliance is not very full and for
50. f Adjustable shelf with lighting 0 57 mterior and ACCESSONES sv 0a cies de Ree adha week pews DAR Bee wR eae hw 59 Boor sedla ar rycie Aa asaya UE coats cect aan Se cept ea meneame E 60 Ventilation Slits s rs ee asar aene aain E a Ra ach awa alse G RAEE gE oS 60 Frequently asked questions nunaa aaa 61 NOIS S 405663445 bd adich bd deed bed hb bbadawhs o2ebebu ted bd tawds Med Sa 73 Contents Lead free certificate 0 0 0 0 eee 74 Service Warranty 0 0 00 0 ccs 75 Warranty ee ere a bu teil aa hee Rae wes a eA 75 Information for dealers showrooms 00000 50 ee eeee 76 Demomodel oeae chet lek aceite aha Gans cane ee agen 76 Caring for the environment 0 000000 cee eee 80 PIUMDING eerten t tow sti ethers ea a he op Ema eden eee a el 81 Information regarding the water connection 0 2 0 0 0 000 eee eee 81 Electrical connection 0 0 0 0 ee 84 Installation information 0 0 0 000 000 eee 86 Installation IOCAtION ier inei phe MEW Re eG ae o he ee RRR OP eee eee a 86 Climate ClaSs serpa p send 3 payee ye dude bee be Gada Poe PERE Reet te 86 Ventilation resres 405 eed de dee ae hat ea tie Gad eho be pads eee bad 87 Ven tatOMeGrill es esate aod teed cached ah ete kas Baca Bede eRe de E wee AE ete a 88 Before installation o oescc arris srs eee aai 89 Installation dimensions aaua 90 Adjusting the door hinge
51. g more frequently using a cotton swab or similar so that condensate can drain away unobstructed To do this remove the PerfectFresh Pro zone drawers m The PerfectFresh Pro zone drawers sit upon telescopic runners Clean these telescopic runners with a damp cloth Be careful not to wash out the special lubricant in the telescopic runners during cleaning 59 Cleaning and care m Remove any soiling on stainless steel strips and plinths with the Miele care product for stainless steel m Always wipe these surfaces with a stainless steel conditioner immediate ly after each cleaning This protects the stainless steel surfaces and prevents resoiling m Leave the appliance doors open for a short time Door seal Do not use any grease or oil on the door seal as these will cause the seal to deteriorate and become porous over time m The door seal should be cleaned regularly with clean water and then wiped thoroughly dry with a soft cloth Ventilation slits m The ventilation slits should be cleaned on a regular basis with a brush or vacuum cleaner A build up of dust will increase the energy consumption of the appliance 60 After cleaning m Put all shelves and accessories back into the appliance The left hand support ribs for the adjustable shelves have metal discs contacts inside the receiving gaps to supply the LED lighting with electricity Ensure these contacts are clean and dry b
52. g the soft close mechanism m Now turn over the appliance door so that the outer side faces downwards m Screw the mount onto the hinge and firmly tighten m Pull the soft close mechanism so that it extends 49 and hook it onto the ball joint m Slide the appliance doors and onto the premounted screws and and firmly tighten the screws and m Replace the covers and m Refit the locking pins into the top of the hinges to prevent the doors opening too far 95 Installing the appliance To install the appliance you will need Two people are required to install the the following tools appliance m Install the appliance in a stable solid housing unit positioned on an even and level floor m Secure the housing unit against tipping m Use a level to align the housing unit The corners of the housing unit must be at a 90 angle to each other otherwise the cabinet door will not align correctly with all 4 corners of the housing unit m The required ventilation cross sections must be ensured see Installation Ventilation and Installation dimensions 96 Installing the appliance Parts required for installation All installation parts are number coded This coding is also used in the installation instructions Required for installing the appliance in its housing unit Required for fitting the cabinet doo
53. gher the energy consumption How to save energy Normal energy consumption Increased energy consumption Use The drawers and shelves are in the original arrangement Only open the doors when necessary and for as short a time as possible Store food in an organized way Frequent opening of the door for long periods will cause a loss of coldness The appliance works harder to cool down and the compressor runs for longer periods When shopping use a cooler box or bag and place the food in the appliance as soon as possible Replace items removed from the appliance as soon as possible before they warm up Allow hot food and drinks to cool down before placing them in the appliance Hot food or food at room temperature raises the temperature inside the appliance The appliance works harder to cool down and the compressor runs for longer periods Store food covered or wrapped The evaporation or condensation of liquids in the refrigerator section lower the cooling capacity Place frozen food in the refrigerator to defrost Do not overfill the appliance in order to allow the air to circulate Turning the appliance on and off Before first use Packaging material m Remove all packaging material from the inside of the appliance Protective film The stainless steel trim and panels are covered with a film to protect them during transportation m Carefully remo
54. he ice cube maker will then turn off m Carefully remove the ice cube drawer which is now filled with water Then empty and clean it The ice cube tray is not removable and can only be cleaned when in place m Dry the ice cube tray with a soft cloth As soon as the ice cube maker is turned on the ice cube tray rotates back to its original position Cleaning the ice cube tray Clean the ice cube maker before switching off the ice cube maker for an extended period of time regularly to remove any ice and water residues If you have already selected the setting Rinse the ice cube maker see Rinsing the ice cube maker the ice cube tray will already be in the cleaning position The ice cube tray is not removable and can only be cleaned when in place You can therefore place the ice cube tray in the cleaning position 55 Cleaning and care Setting the cleaning position The setting can only be selected if the ice cube maker is turned on m Empty the ice cube drawer gt ANN m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes m Touch the buttons for setting the temperature V or A repeatedly until the symbol for the ice cube maker ag flashes in the display m Touch the OK button to confirm your selection m The required setting can be selected by touching the X and Y buttons
55. he interior lighting will come on If this is not the case then there is a fault m Contact Miele Technical Service 68 Frequently asked questions Interior lighting Problem Possible cause Solution The LED lighting for the PerfectFresh Pro zone does not work To avoid overheating the lighting turns itself off automatically after approx 15 minutes if the door is left open m Close the appliance door When the door is opened again the interior lighting will come on If this is not the case then there is a fault m Contact Miele Technical Service The LED lighting may only be repaired or replaced by Miele Technical Service There are live electrical components under the lighting cover Danger of injury and damage to the appliance Do not remove the cover If the cover is damaged or needs to be removed due to damage use caution There are lasers in the lighting laser beam class 1M which you should avoid looking at directly Do not use optical instruments magnifying glass or similar to look at the lighting either 69 Frequently asked questions Other problems Problem Possible cause Solution Food has frozen together or to the wall The food packaging was not dry when loaded in the freezer m Use a blunt instrument such as a spoon handle to carefully pry them apart There is no acoustic alarm a
56. helf Adjustable shelf with lighting 00000 42 Moving the shelf Shelf with lighting 0 0 0 0 0 000 cece ee 42 Adjusting the bottle rack 2 4e5 8480044 Peek ede ae bas bebe ewewa gawd 43 PerfectFresh Pro ZONE COMPANMENS 4 4 cto Peter wig tay Maan ey KPA Seaweeds 43 Freezing and storing food 0 0 0 ee 45 Maximum freezing capacity o a aaa aa 45 What happens when you freeze fresh food 2 eee 45 SLOMNGATOZEM 1000 saeco gi be hal Abba jeg bade ad jaan die oa bt 45 Before placing food in the freezer 6 eee 46 Placing food in the freezer ee eee 46 Thawing frozen fO00S s aes0 dare a aey pede de iieiea a t pataa ten a E A E nee 47 Cooling drinks quickly 0 0 eee eee 47 USING meco PACK erer en nera nat ae ate dua Saha ede ane We Logue nan 47 Making ice cubeS 0 ce eee 48 Ice cube maker with integrated ice cube tray 0 eee 48 Turning the ice cube maker On Off 0 0 0 0 eee 49 Making a large amount of ice cubes 0 49 Changing the size of the ice cubes n nananana 50 Setting the water quantity 2 ee ees 50 Turning the ice cube maker On Off with the On Off button 51 Automatic defrosting 0 0 0 0 0 52 Cleaning and care 0 00 0 53 Rinsing the ice cube maker 2 0 00 eee 54 Cleaning the ice cube tray 0 0 0 tae 55 Setting the cleaning position 0 0 2 000000 cee 56 Adjustable shel
57. her the food has defrosted or started to defrost If this is the case cook the food before freezing again The acoustic alarm sounds and the power failure symbol appears in the display The temperature display will show the warmest temperature recorded in the freezer section during the power failure or interruption to the power supply The temperature in the appliance in the previous days or hours has risen too high because of a power failure or interruption to the power supply The appliance will go back to the last temperature setting when the power is back on m Touch the alarm off button The warmest temperature display will go out The display will then revert to showing the current temperature in the freezer section m Depending on the temperature displayed you should check the condition of food in the freezer If it has defrosted or started to defrost check that it is still safe to use and if so use it as soon as possible Defrosted food may only be re frozen after it has been cooked 66 Frequently asked questions Interior lighting Problem Possible cause Solution The LED lighting on the shelves does not work To avoid overheating the lighting turns itself off automatically after approx 15 minutes if the door is left open m Close the appliance door When the door is opened again the interior lighting will come on Th
58. hich reduce the amount of energy supplied to the appliance and cause it to overheat If the power cord needs to be replaced this work must only be performed by a qualified electrician 85 Installation information To avoid tipping over the appliance must be properly installed and secured WARNING Danger of tilting To avoid a hazard due to instability of the appliance it must be secured in accordance with the instructions Installation location This appliance should not be installed where it is exposed to direct sunlight or directly adjacent to a heat producing appliance such as an oven or a radiator The higher the ambient temperature of the room the longer the compressor runs and the more energy the appliance requires to operate The appliance should be installed in a dry well ventilated room The following should also be taken into consideration The plug must be easily accessible and not concealed behind the appliance so that the appliance can quickly be disconnected from the electricity supply in an emergency In addition no other appliances should be plugged into a socket located directly behind this appliance The power cable must not come into contact with the back of the appliance as they could be damaged by vibrations from the appliance This may result in a short circuit 86 Important In environments with high humidity condensation can build up on the appliance exterior a
59. hread The connection parts included with the appliance permit the connection of various water lines a water line is not included in delivery m Remove the cap from the solenoid valve m Insert the adapter into the union nut 82 In the following please note inserting the water filter incorrectly can cause damage m Place the water filter on top of the adapter as shown in the picture Do not over tighten the union nut damage can result m Connect the union nut to the solenoid valve and tighten it m f you want to divert the water line by 90 screw on the elbow In case of a water line with a 1 4 thread m Connect the water line e g copper using the clamping ring and the nut on the adapter or elbow In case of a water line with a 7 16 24 UNS thread m Connect the water line directly to the adapter or elbow a clamping ring and nut are not required Plumbing m Secure the water line using the retaining clip 4 m Slowly open the water shut off valve and check for leaks m The appliance can now be connected to the power supply see Electrical connection m Slide the appliance into the desired position When doing so make sure that the water does not get kinked or damaged After a maximum of 24 hours the first ice cubes will drop out of the ice cube maker and collect in the drawer
60. iformly shiny surface Stainless steel trim with LED lighting for shelf FlexiLight LED lighting is located on the Optional accessories are available stainless steel trim which is supplied from Miele your Miele dealer or with electricity via metal discs online contacts Refrigerator lighting can be customized to your needs by changing the position of the shelf Bottle rack Bottles can be stored horizontally using the bottle rack to save space The bottle rack can be placed at different positions in the appliance How to save energy Normal energy consumption Increased energy consumption Installation Maintenance In a well ventilated room In an enclosed poorly ventilated room Protected from direct sunlight In direct sunlight Away from heat sources radiator range oven Near a heat source radiator range oven Where the room temperature is ideal i e around 68 F 20 C Where the room temperature is higher Do not block the ventilation openings and keep them free of dust Where the ventilation openings are blocked and full of dust Temperature setting 14 39 to 41 F 4 to 5 C in the refrigerator section PerfectFresh Pro zone just above 32 F 0 C O F 18 C in the freezer section With a low temperature setting the colder the temperature in the refrigerator and freezer zones the hi
61. ighboring unit doors The door panel must be installed correctly and not under tension Installing a door front which is heavier than the maximum permitted could damage the hinges This can cause damage Before installing door fronts ensure that the weight of the door does not exceed the maximum permitted Appliance Max Max weight weight of of the upper lower cabinet cabinet door in door in Ib kg lb kg KFNS 37692 iDE 44 20 26 12 When fitting large or divided cabinet doors an extra fitting kit or set of fixing brackets should be used These are available to order from Miele 103 Installing the appliance Complete the following steps on both doors Tip Push installation aids together with the cabinet front up to the height of the adjoining unit cabinet doors m A gap of 5 16 8 mm is set ex works between the appliance door and the fixing bracket Double check this gap and reset it if necessary m Push the installation aids up to the height of the cabinet door the lower m Remove the nuts and take the edge X of the installation aids must mounting bracket off together with be at the same height as the upper installation aids edge of the cabinet door being fitted see A on the diagram 104 Installing the appliance m Place the door panel with the outer side downwards on a stable
62. ilable for selection will appear in the display and the amp symbol flashes m Tap the buttons for setting the temperature V or A repeatedly until the SJ symbol flashes in the display m Tap the OK button to confirm your selection The last selected setting flashes in the display and the lights up m By tapping the V or A button you can now alter the brightness of the display i dimmest setting 2 medium setting 3 brightest setting m Tap the OK button to confirm your selection The selected setting will be adopted and the symbol will flash Ye Q m Tap the settings button to leave the settings mode Otherwise the appliance exits the settings mode automatically after approximately one minute 33 Making additional settings Sabbath mode ij To facilitate religious customs the appliance has a Sabbath mode The following are switched off the interior lighting when the door is opened all audio and visual signals the temperature display SuperCool and SuperFreeze if previously switched on the ice cube maker if previously switched on The following can be used the settings button for switching off the Sabbath mode and the On Off button The Sabbath mode function automatically switches off after 120 hours Since the audio and visual warnings are turned off make sure the doors are closed properly There is no warning if a power su
63. ining solvents stainless steel cleaners dishwasher detergent oven sprays hard abrasive sponges and brushes such as pot scrubbers eraser sponges sharp metal scrapers Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly To clean stainless steel surfaces on the appliance use the Original Miele care product for stainless steel see Guide to the appliance Optional accessories This product contains substances that are gentle to stainless steel surfaces and unlike stainless steel cleaners it does not contain polishing agents Soiling is gently removed and each time the Original Miele Care product for stainless steel is used it forms a protective film against dirt and water Use warm water and liquid dish soap The following pages contain important information on cleaning 53 Cleaning and care Rinsing the ice cube maker Rinse out the ice cube maker and the water pipes before using for the first time if the ice cube maker has not been used for quite a while regularly at least once a month if it is constantly being used to remove any ice residues and therefore avoid an blockages in the water pipes and before switching the ice cube maker off for an extended period of time After selecting Rinse the ice cube m
64. ion and in the PerfectFresh Pro zone We recommend a temperature of 39 F 4 C in the refrigerator section The temperature in the PerfectFresh Pro zone is controlled automatically and is maintained at 32 to 37 F 0 to 3 C 20 Automatic cold air circulation DynaCool The fan automatically turns on when the cooling system for the refrigerator section turns on It distributes the temperature in the appliance to all areas more evenly so that all the food will be chilled to about the same degree in the freezer section To freeze fresh food and to store frozen food for a long time a temperature of 0 F 18 C is required At this temperature the growth of micro organisms is generally halted As soon as the temperature rises above 14 F 10 C the bacteria become active in the food again so that it cannot be kept as long For this reason partially defrosted or fully defrosted food must not be re frozen Food may be re frozen once it has been cooked as the high temperatures achieved when cooking destroy most bacteria The right temperature Temperature display In normal operation the display shows the current average refrigerator temperature and the temperature in the warmest part of the freezer Dashes are displayed if the temperature in the freezer section is not within the displayable range Depending on the ambient temperature and the temperature setting it can take the appliance a f
65. l is too low wrap the food in air tight packaging The humidity level in the humidity controlled compartment is determined by the type and quantity of food when it is not packaged 39 Storing food in the PerfectFresh Pro zone If the humidity level in the humidity controlled compartment is high condensate may collect on the floor of the compartment or underneath the lid This can be removed with a cloth 40 Regulating the humidity level in the humidity controlled compartment Use the slide control to regulate the humidity level in this compartment to 6 66 or 666 m Push the slide control all the way to the back and then slowly release it The slide control automatically clicks into the 6 position m To select either the 66 or 666 setting push the slide control to the back again and release it so that it clicks into the 66 or 666 position Storing food in the PerfectFresh Pro zone If you are not satisfied with your stored food for example the food wilts or becomes withered after only a short storage time check the following m Only place fresh food in the appliance m Clean the PerfectFresh Pro compartments before storing food in them m Very wet food should be dried off before storing it m Do not store any food in the PerfectFresh Pro zone which is sensitive to cold see Food which should not be stored in a refrigerator m For the type of food being stored sel
66. lated from the electrical supply when the respective fuse has been removed the circuit breaker has been tripped or the power cord has been unplugged Pull on the plug and not on the cord when removing it from the outlet B Installation repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions Contact Miele s Technical Service Department for examination repair or adjustment gt The ice cube maker is not intended to be used with a hot water supply line P gt Repairs and other work performed by unauthorized persons could be dangerous and may void the warranty gt Defective components should only be replaced by Miele original parts Only with these parts can the manufacturer guarantee the safety of the appliance Proper use gt The appliance is designed for use within a certain climate range ambient temperatures and should not be used outside this range The climate range for your appliance is stated on the data plate inside the appliance Installing it in a room with too low an ambient temperature e g a garage will lead to the appliance turning off for longer periods so that it cannot maintain the required temperature gt WARNING Danger of damage from overheating May restirct operation Keep ventilation openings in the appliance enclosure or in the buil
67. lthough the door has been open for a long time This is not a fault The alarm tone has been turned off in settings mode see Selecting additional settings Acoustic signals None The appliance cannot be turned off The safety lock is activated The amp symbol is lit up in the display m Turn off the safety lock see Selecting settings deactivating the safety lock The external walls of the appliance feel warm This is not a fault The warmth created by the evaporator is used to prevent condensation None The floor of the refrigerator section is wet The drain hole is blocked m Clean the condensate channel and the drain hole 70 Frequently asked questions Problems with the ice cube maker Problem Possible cause Solution You cannot turn the ice cube maker on The appliance is not connected to the power supply or is not turned on m Connect the appliance and turn it on The ice cube maker does not produce any ice cubes The appliance or the ice cube maker is not turned on m Turn the appliance and the ice cube maker on The water supply line is not open m Open the water intake The drawer of the ice cube maker is not closed properly m Push the drawer all the way in The ice cube tray is not positioned correctly m Correct the position of the ice cube tray The temperature in the freezer
68. ly less than that of fresh vegetables due to changes in the cell structure Never re freeze partially or fully defrosted food Defrosted food may only be re frozen after it has been cooked Cooling drinks quickly When cooling drinks quickly in the freezer make sure bottles are not left in for more than one hour otherwise they could burst Using the cool pack The cool pack prevents the temperature in the freezer rising too quickly in the event of a power cut This can help prolong the storage time m Place the cool pack in the top drawer of the freezer section The cool pack will be at its most effective after it has been in the freezer for approx 24 hours In the event of a power failure m Place the frozen cool pack directly on top of the frozen food in the front of the top drawer When placing fresh food in the freezer use the cool pack to separate the fresh food from the already frozen food so that the frozen food does not begin to thaw The cool pack can also be used to keep food or drinks cool for a short period of time in a cooler box or bag 47 Making ice cubes For the automatic ice cube maker to operate it must be connected to the water supply Ice cube maker with integrated ice cube tray The automatic ice cube maker is located in the ice cube freezer drawer As soon as the ice cube maker is turned on the 8 symbol lights up in the display and the indicator
69. m After cleaning reattach the stainless steel plinth to the shelf in reverse order Cleaning and care Interior and accessories Clean the appliance at least once a month Remove any soiling immediately so that it does not dry up m Clean the interior with lukewarm water and a little dishwashing liquid applied with a soft sponge After cleaning wipe with a clean damp cloth and then dry with a soft cloth The following parts can be cleaned in a dishwasher bottle holder butter dish egg tray depending on model bottle shelf and door shelf on the inside of the door without stainless steel plinth shelves without stainless steel strips with LED lighting stainless steel strips and protective strips The maximum temperature of the dishwashing program selected must not exceed 130 F 55 C Contact with natural dyes from carrots tomatoes and ketchup may discolor the plastic parts in the dishwasher This discoloring does not affect the stability of the parts The following parts cannot be cleaned in a dishwasher the stainless steel plinths on the door shelf bottle shelf the stainless steel strios with LED lighting stainless steel strips and protective strips on the shelves the bottle rack PerfectFresh Pro zone drawers with the respective drawer lids the ice cube drawer the freezer drawers Clean these parts by hand Clean the condensate channel and drain openin
70. nd ultimately cause corrosion on the outer walls To prevent this from happening we recommend installing the appliance in a dry and or an air conditioned room with sufficient ventilation Once you have completed the installation please make sure that the appliance doors close properly that the ventilation openings are not covered and that the appliance has been installed as described Climate class The appliance is designed for use within a certain climate range ambient temperatures and should not be used outside this range The climate range of the appliance is stated on the data plate inside the appliance Climate Room temperature class SN 50 F to 90 F 10 C to 32 C N 60 F to 90 F 16 C to 32 C ST 60 F to 100 F 16 C to 38 C T 100 F to 110 F 16 C to 43 C Operating in a room which is too cold will cause the compressor to turn off for too long causing the internal temperature in the appliance to rise resulting in damage Installation information Ventilation WARNING Danger of damage from overheating May restrict operation Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction The ventilation gaps given must be observed otherwise the compressor will run more frequently and for longer periods This will result in increased energy consumption and a higher operating temperature for the compressor
71. ning off the ice cube maker for a long period of time Transport gt Always transport the appliance in an upright position and in its original transport packaging to avoid damage in transit gt The appliance is very heavy and must be transported by two people Danger of injury and damage Disposal of your old appliance P There is a risk of suffocation Children playing can shut themselves in and suffocate Take the door s off Remove the drawers Leave the storage shelves in the appliance so that children cannot easily climb into the appliance B Danger of electric shock Cut off the plug from the power cord and discard Cut off the power cord from the discarded appliance Dispose of separately from the appliance P Ensure during and after disposal that the appliance isn t stored in the vicinity of gasoline or other flammable vapors and liquids B When disposing of the appliance ensure that the refrigeration circuit is not damaged to prevent uncontrolled escape of the refrigerant it contains data on type plate and oil gt Take care not to damage any part of the cooling system for example by puncturing the coolant channels in the evaporator kinking any pipework scratching the surface coating Caution Spraying coolant can damage the eyes SAVE THESE INSTRUCTIONS AND PASS THEM ON TO ANY FUTURE USER Guide to the appliance Control panel iene S
72. ntally friendly Although it is flammable it does not damage the ozone layer and does not increase the greenhouse effect The use of this coolant has however led to a slight increase in the noise level of the appliance In addition to the noise of the compressor you might be able to hear the coolant flowing around the system This is unavoidable and does not have any adverse effect on the performance of the appliance Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged Leaking refrigerant can damage the eyes In the event of any damage avoid open flames and anything that creates a spark disconnect the appliance from the electrical power supply air the room in which the appliance is located for several minutes and contact Miele Technical Service P The more coolant there is in an appliance the larger the room it should be installed in In the event of a leakage if the appliance is in a small room there is the danger of combustible gases building up For every 8 g of coolant at least 1 m of room space is required The amount of coolant in the appliance is stated on the data plate inside the appliance P To avoid the risk of damage to the appliance make sure that the connection data fuse rating frequency and voltage on the data plate corresponds to the household supply Check that this is the case before connecting th
73. od condition from the start to get good storage results Take food out of the PerfectFresh Pro zone approx 30 60 minutes before using it The aroma and flavor do not fully develop until the food has reached room temperature The PerfectFresh Pro zone is divided into two compartments The upper dry compartment has a temperature of between 32 37 F 0 3 C The humidity level in this compartment is not increased 6 In this compartment you should store fish meat dairy products and any other type of food as long as it is packaged The lower humidity controlled compartment in different numbers depending on model has a temperature of between 32 37 F 0 3 C The humidity level can be kept low or high 66 666 depending on the position of the slide control If the humidity is increased in this compartment fruit and vegetables should be stored inside it Each type of food has its own characteristics and requires certain storage conditions The info system above the PerfectFresh Pro zone helps you choose the correct compartment and or select the appropriate setting in the humidity controlled compartment amp 6 gt ead 6 38 Miele PerfectFresh Pro ob 4s amp S Pp 8 P hh amp 666 Storing food in the PerfectFresh Pro zone Dry compartment 6 The dry compartment is suitable for storing perishable foods such as fresh fish shellfish meat poultry sausag
74. of the appliance They are important for trouble free operation of the appliance and normal energy consumption Freezing the maximum amount see data plate m Remove the upper freezer drawers m Place the food flat on the upper glass cold plates so that it freezes through to the core as quickly as possible Once frozen m Place the frozen food in the freezer drawer and push it back in Large items If you wish to freeze large items such as turkey or game you can remove the glass shelves between the freezer drawers m Remove the upper freezer drawers and carefully slide out the glass cold plates Freezing and storing food Thawing frozen foods Frozen food can be thawed in various ways inthe microwave in a regular oven using the fan or defrost setting at room temperature in the refrigerator as it thaws the frozen food will help cool the other food in the refrigerator in a steam oven Flat pieces of partially thawed meat or fish can be placed directly into a hot skillet Meat and poultry e g hamburger chicken fish fillets may not come into contact with other foods while defrosting Catch the defrosting liquid and dispose of it carefully Fruit can be thawed at room temperature either in the packaging or in a covered bowl Most vegetables can be cooked while still frozen Just put straight into boiling water or hot fat The cooking time is slight
75. pply failure occurs After a power supply failure the appliance will come back on in Sabbath mode 34 Switching on Sabbath mode v J m Tap the settings button All symbols available for selection will appear in the display and the amp symbol flashes Bb m Tap the buttons for setting the temperature V or A repeatedly until the fi symbol flashes in the display BS m Tap the OK button to confirm your selection The last selected setting flashes in the display and the fi lights up Bb m By tapping the V or A button you can now switch on Sabbath mode To do this select setting 1 P m Tap the OK button to confirm your selection Making additional settings The selection is saved and the fi symbol lights up Sabbath mode is on when the symbol goes out after 3 seconds m Turn Sabbath mode off when the Sabbath is over Switching off Sabbath mode p A m Tap the settings button to leave Sabbath mode The temperature will appear in the display and the interior lighting will come on 35 Storing food in the refrigerator section Various cooling zones Due to the natural circulation of the air in the appliance there are different temperature zones in the refrigerator section Cold heavy air sinks to the lowest section of the appliance Make use of the different zones when placing food in the appliance This appliance has DynamicCooling which helps to ke
76. r All installation instructions given are for a right hand hinged appliance If you have converted the appliance to left hand hinging you will need to adapt these instructions accordingly Preparing the appliance m Position the appliance in front of the housing unit 97 Installing the appliance m Fit the straps of the compensation strip into the strut seats front rom the m Screw fixing bracket using hex screw to the pre drilled holes in the appliance door Using the pre drilled holes in the appliance door secure a second pair of fixing brackets in the handle area of the door 98 m Push the appliance two thirds of the way into the installation space Ensure that the power cord does not get caught Tip to help you push it into position Tie a piece of string around the plug to increase the length of the power cord Then pull the cable by the end of the string through the housing unit It will then be easier to connect once the appliance is in the unit Only in the case of 5 8 16 mm thick unit walls m Clip the spacers and on the right hand side of the hinges m Open the appliance doors Installing the appliance PA A S m Remove the cover m Secure the fastening part using screws 8 loosely into the top left hand side of the appliance Do not tighten the screws so that you can adju
77. r fully defrosted food Consume defrosted food as soon as possible as it will lose its nutritional value and spoil if left for too long Defrosted food may only be refrozen after it has been cooked B Use only genuine original Miele parts If parts or accessories from other manufacturers are used the warranty may become invalid Cleaning and care P Do not use any oil or grease on the door seals They can cause the seals to deteriorate over time gt Never use a steam cleaner to clean the appliance The steam can reach the electrical components and cause a short circuit P gt Never use a pointed or sharp edged object to remove frost or ice or to detach food items frozen to the walls This will damage the evaporators causing damage to the appliance P Do not place electric heaters or candles in the appliance to defrost it These can damage the plastic parts P Do not use defrosting sprays or de icers as they could contain substances which could damage the plastic parts or which might cause the build up of gases and pose a danger to health IMPORTANT SAFETY INSTRUCTIONS P gt Rinse the ice cube maker and the water pipes before using for the first time if the ice cube maker hasn t been used for a long time regularly if the ice cube maker is constantly on at least once a month to remove ice residues and prevent the water pipes from becoming blocked and before tur
78. r has been placed in position and closed properly Changing the size of the ice cubes The size of the ice cubes depends on the quantity of water being taken in You are able to set this quantity according to your wishes Setting the water quantity The size of the produced ice cube depends on the water pressure and set water intake time of the ice cube maker If for example the ice cube maker only makes small ice cubes the water pressure is low To produce larger ice cubes the water quantity of the ice cube maker must be increased A medium sized water quantity 7 has been set at the factory The setting can only be selected if the ice cube maker is turned on gt ANN m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes 50 m Touch the buttons for setting the temperature V or A repeatedly until the symbol for the ice cube maker ag flashes in the display m Touch the OK button to confirm your selection m The V and A buttons can be used to set whether the water quantity is to be changed 0 Ice cube maker is switched off i Ice cube maker is switched on 2 Set the water quantity 3 Ice cube tray cleaning position 4 Rinse the ice cube maker m Touch the OK button to confirm your selection m Touch the V and A buttons to set the required water quantity E7 to 8 El small quantity 8 large quantity m Touch the O
79. reezer section m Close the door After a while the temperature will return to normal by itself If a thick layer of ice has formed it will decrease the cooling capacity and increase the energy consumption m Defrost the freezer section and clean it The room is too warm The higher the room temperature the longer the compressor has to run m See Installation location The appliance was not properly installed in the niche m See Installation and Installing the appliance 63 Frequently asked questions The compressor comes on less and less often and for shorter periods of time the temperature in the appliance rises Problem Possible cause Solution The temperature in the appliance is too high This is not a fault m Correct the temperature setting m Check the temperature again after 24 hours The food begins to thaw The room temperature is too low for this appliance The compressor turns on less frequently when the room temperature is too low This can result in the freezer section becoming too warm m See Installation location m Increase the room temperature 64 Frequently asked questions Indication in the display Problem Possible cause Solution FO to FS appears in the display There is a fault m Contact Miele Technical Service FE appears in the display Ther
80. s and the display is dark The appliance is not turned on and the power supply symbol is lit up in the display m Touch the On Off button The plug is not properly plugged into the electrical outlet m Insert the plug correctly into the socket The power supply symbol appears in the display when the appliance is turned off Check whether the fuse has tripped There could be a fault with the appliance the household electrical wiring or another electrical appliance m Contact a qualified electrician or Miele Technical Service for assistance The appliance does not get cold although the controls and the interior lighting are working Demo mode is turned on and the If symbol lights up in the display This allows the appliance to be presented in the showroom without the cooling system being turned on Do not activate this setting for domestic use m Turn off Demo mode see Information for dealers Demo mode 61 Frequently asked questions The compressor runs more and more often and for longer periods of time and the temperature in the appliance drops Problem Possible cause Solution The temperature in the appliance is too low The temperature setting is too low m Correct the temperature setting The freezer section door is not properly closed m Check whether the freezer section door closes properly A large amount of
81. selection F flashes in the display Making additional settings aN m By tapping the V or A button you can now select C m Touch the OK button to confirm your selection The selected setting will be adopted m Touch the settings button to leave the settings mode Otherwise the appliance will exit the settings mode automatically after approximately one minute The temperature will now be displayed in Celsius Setting the temperature display to Fahrenheit gt ANS m Touch the settings button All symbols available for selection will appear in the display and the amp symbol flashes AN m Touch the buttons for setting the temperature V or A repeatedly until C and F flash in the display AN m Touch the OK button to confirm your selection flashes in the display ANC m By tapping the V or A button you can now select F ANC m Touch the OK button to confirm your selection The selected setting will be adopted m Touch the settings button to leave the settings mode Otherwise the appliance will exit the settings mode automatically after approximately one minute The temperature will now be displayed in Fahrenheit 31 Making additional settings Acoustic signals JJ The appliance features acoustic signals such as a keypad tone and acoustic alarm for the door and temperature m By tapping the V or A button you can alarm now select You can switch
82. st current product specification technical amp warranty information To prevent accidents and machine damage read these instructions before installation or use Caring for the environment Disposing of the packaging materials The packaging is designed to protect the appliance from damage during transportation The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Return the packaging to your dealer 80 Disposal of your old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Please take care not to damage the pipework while the appliance is being stored for transport to a waste disposal facility By protecting the pipework you help keep the coolants and compressor oil from contaminating the environment Before discarding an old appliance disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard Plumbing Information regarding the water connection All plumbing work should be carried out by a suitable qualified person in accordance with local and national regulations Disconnect the appliance from the power supply before connecting it to the water supply
83. st the position of this part m Fit the cover onto the fixing bracket 40 m Then screw fixing bracket 0 using screws 4 loosely into the bottom of the appliance Do not tighten the screws so that you can adjust the position of this part m Now screw the adjustable feet 42 all the way in m Carefully remove the protective foil from sealing strip 43 m Fix sealing strip 4 flush with the front of the appliance on the door opening side 1 Position the sealing strip flush with the lower edge of the top fixing 2 Stick it down along its entire length 99 Installing the appliance Installing the appliance m Push the appliance into the niche until all of the brackets are in line with the front edge of the furniture side wall With 5 8 16 mm thick walls The spacers should touch the front edge at the top and bottom of the side walls of the housing unit With 3 4 19 mm thick walls The front edges of the top and bottom hinges should be flush with the front edge of the housing side walls 100 m Check the position of the fixing bracket at the top and bottom front edge of the cabinet side wall again This will help maintain a 1 5 8 42 mm distance all the way around from the front edges of the cabinet side walls On cabinetry with door fittings e g stubs seals etc the dimension of these must be taken into
84. t in structure clear of obstruction P If you store fatty or greasy foods in the appliance or the appliance door make sure that no oil or grease leaks onto the plastic parts of the appliance This can cause the plastic to crack and break gt Do not store explosive materials in the appliance or any products containing propellants e g spray cans Electrical components cou cause flammable vapors to ignite Danger of fire and explosion Q IMPORTANT SAFETY INSTRUCTIONS gt Do not operate any electrical equipment e g an electric ice cream maker inside the appliance Danger of sparking and explosion B Do not store cans or bottles containing carbonated drinks or liquids which could freeze in the freezer section The cans or bottles could explode Danger of injury and damage to the appliance B gt When cooling drinks quickly in the freezer section make sure bottles are not left in for more than one hour otherwise they could burst causing injury and damage gt Never handle frozen food or the metal parts of the appliance with wet hands Your hands may freeze to the frozen food or to the metal Danger of frost burn P Do not take ice cubes out with your bare hands and never place ice cubes or popsicles in your mouth straight from the freezer section The very low temperature of the frozen ice or popsicles can cause frost burn to the lips and tongue Danger of injury P Do not refreeze partially o
85. t up the bottle shelf and pull it forward to remove it m Detach the bottle holder from the back edge of the bottle shelf 42 Adjustable shelf Adjustable shelf with lighting The LED lighting is located on the stainless steel trim of the shelf By adjusting the position of the shelf in the refrigerator section you can change the illumination in this section according to your needs If the lighting does not work check that the shelf is correctly positioned in the shelf supports The shelf has metal discs contacts on the front left corner to enable electricity to be supplied to the LED lighting When inserting the shelf ensure the contacts click into position in the shelf support Moving the shelf Shelf with lighting The shelves can be adjusted according to the height of the food m Lift the shelf at the front pull it forwards slightly lift the recess over the shelf supports and move the shelf up or down Adjusting the interior fittings The edge of shelf s rear stop must face upwards so that food does not touch the rear wall and freeze to it Stops prevent the shelves from being pulled out accidentally Adjusting the bottle rack The bottle rack can be placed on different levels in the appliance m Raise the rack and pull it forwards slightly until the notch at the side is in line with the shelf support It can then be raised or lowered to the required level
86. the button tone or the 0 button tone off door alarm off door alarm acoustic alarm on or off but 1 button tone off door alarm on you cannot deactivate the temperature after 4 minutes alarm button tone off door alarm on after 2 minutes 3 button tone on door alarm on after 2 minutes There are four settings to choose from Option 3 is set the factory i e the button tone and the door alarm are switched on Switching acoustic signals on off m Tap the OK button to confirm your selection The selected setting will be adopted m Tap the settings button and the J symbol will flash All symbols available for selection will gt appear in the display and the amp symbol flashes m Tap the settings button to leave the settings mode Otherwise the appliance exits the m Tap the buttons for setting the settings mode automatically after temperature V or A repeatedly until approximately one minute the SJ symbol flashes in the display m Tap the OK button to confirm your selection The last selected setting flashes in the display and the JS lights up 82 Making additional settings Display brightness You can adjust the brightness of the display to suit the light conditions in the room The display brightness can be adjusted in steps from 7 to 3 The factory default setting is 3 maximum brightness Changing the brightness of the display m Tap the settings button gt All symbols ava
87. ton so that it running at normal cooling capacity is highlighted yellow The temperature in the appliance now begins to fall since it is operating at maximum cooling capacity 24 SuperCool The SuperCool function in the freezer For best results turn on SuperCool before putting fresh food into the freezer Fresh food will be frozen quickly so that the nutritional value vitamin content appearance and taste are maintained Exceptions if you have already put frozen food into the freezer when freezing up to 4 5 Ibs 2 kg fresh food daily Turning on SuperCool When freezing small quantities of food in the freezer the SuperCool function should be turned on 6 hours beforehand When freezing the maximum load of food the SuperCool function should be turned on 24 hours beforehand m Touch the sensor button for the freezer section The freezer section symbol will light up yellow m Touch the SuperCool button so that it is highlighted in yellow The temperature in the appliance now begins to fall since it is operating at maximum cooling capacity 25 SuperCool Turning off SuperCool The SuperCool function will turn itself off automatically after approx 30 65 hours The quantity of fresh food placed in the freezer will determine the duration before the SuperCool function turned off The SuperCool symbol will go out and the appliance will run at normal cooling capacity again
88. ur thumb towards the housing unit wall while tightening the screws The appliance must not pull back into the unit m Retighten screws and Installing the appliance For additional stability of the appliance in the unit push the rods supplied in underneath the appliance between it and the floor of the housing unit m Snap off any protruding ends from the mounting bracket They are no longer required m Replace covers and on the mounting brackets m Then secure handle to one of the rods 3 m Use the handle to push the rod into the guide as far as it will go Remove the handle and fit it to the other rod and push this into its guide as far as it will go Important Keep the handle somewhere safe in case you ever need to fit the appliance into a new housing unit m Close the appliance doors 102 Installing the appliance Installing the custom door front The cabinet door must be at least of 5 8 16 mm thick and not exceed 3 4 19 mm thick The following gap dimensions must be maintained The gap between the cabinet door and the unit door above must be at least 1 8 3 mm The vertical gap between cabinet doors should also be about 1 8 3 mm The exact dimension will vary depending on the radius of the cabinet door edges If fitted in a run of units make sure that the top edge of the cabinet door is at the same height as ne
89. ve the protective foil from the stainless steel trim Cleaning and Care It is essential to follow the relevant instructions in Cleaning and care m Immediately after pulling the film off wipe the stainless steel surfaces with the Miele stainless steel conditioner provided Important Each application of the Miele stainless steel conditioner forms a durable protective film that is stain and water resistant m Clean the inside of the appliance and the accessories m Clean the ice cube maker After selecting the Rinse ice cube maker setting the ice cube maker and the water pipes are rinsed automatically with water 16 Accessories Bottle holder The fins of the bottle holder jut out into the bottle shelf and make bottles more secure when opening and closing the appliance door m Attach the bottle holder centrally along the rear edge of the bottle shelf Cool pack Place the cool pack in the top freezer drawer The cool pack will be at its most effective after it has been in the freezer for approx 24 hours Turning the appliance on and off Operating the appliance The appliance is operated with the use of touch keys activated by a finger A tone will sound each time a button is touched You can deactivate this if you wish see Selecting additional settings Acoustic signals Turning the appliance on The power supply symbol appears in the display when the appliance
90. will otherwise switch to normal operation after one minute Make only the number of ice cubes required in your household with the ice cube maker The drawer must be completely shut for ice cubes to be produced After the appliance is turned on for the first time it can take up to 24 hours for the first ice cubes to drop out of the ice cube maker and collect in the drawer Thereafter when the ice cube maker is turned off and then on again it will take up to a maximum of 6 hours for ice cubes to be produced The ice cube maker can be turned off independently of the freezer section if you do not want the appliance to make any ice cubes If the ice cube maker is turned off the ice cube drawer can be used as an extra drawer for freezing fresh food and storing frozen food Making a large amount of ice cubes The amount of ice cubes which the appliance makes depends on the temperature in the freezer section The lower the temperature the more ice cubes are produced within a certain time frame At a temperature of 0 F 18 C approx 2 Ibs 1 kg of ice cubes will be produced within 24 hours Ice cube production is halted automatically as soon as the ice cube drawer is full 49 Making ice cubes If you require a large quantity of ice cubes m replace the full ice cube drawer with the drawer beside it on the right The ice cube maker will begin to produce ice cubes again as soon as this new drawe

Miele KFNS 37692 iDE Operating and Installation Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents