Miele G 5910 User's Manual
Contents
1. m Fold the bar down and lean the desired glasses against it m Pull the cup rack upwards and click it w If desired a section of the cutlery tray back into position at the required can be removed to allow for even width taller glasses 25 Loading the dishwasher Adjusting the height You can set the support bar at two different heights 0 N m Pull the support bar upwards and click it back into position at the required height Use the low setting for small glasses and tumblers Use the high setting for tall glasses and stem ware 26 Loading the dishwasher Adjusting the upper basket In order to gain more space for taller items the upper basket can be adjusted on three levels with 2 cm between each level The upper basket can also be set at an angle with one side high and the other side low Make sure however that the basket can slide smoothly in and out of the cabinet m Slide out the upper basket To adjust the upper basket upwards m Lift the basket up until it clicks into place To adjust the upper basket downwards m Pull up on the levers at the sides of the upper basket m Adjust the basket to the desired height and then release the levers to lock the basket in place Depending on the setting of the upper basket the following plate dimensions can be accommodated Depending on the setting of the upper basket a variety of plate dime2. 79 Electrical connection Hardwired electrical connection Itis possible to hardwire this appliance to an existing power cable NCAUTION Before servicing disconnect the power supply by either removing the fuse shutting off the power main or manually tripping the circuit breaker Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible Before connecting the appliance to the power supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent machine damage Consult an electrician if in doubt GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance 80 Prior to making a hardwire connection to the terminal remove the power cord Otherwise there will be a risk of electric shock from the attached plug An existing flexible supply cord or cable shall have a minimum thickness of AWG 14 120 V 60 Hz 15 A fuse rating Black wire live connect to L White wire neutral connect to N Gr
3. If refill salt and or rinse aid or an fault are present in the display the dishwasher will not turn off The refill messages can be turned off when you use a tab detergent see Settings Refill display Fault messages cannot be turned off Refill display When consistently using multi function Tab detergents you can turn off the refill displays m Select the desired setting and confirm with OE Be sure to turn this setting back on if you stop using multi function tab detergents Check filters This selection allows you to set the number of programs run before the filter check message shows You can select between 30 and 60 programs The filter check message is set by default to 50 programs m Select the desired number of programs and confirm with OK 51 Settings F Reorganize programs The order of the programs in the program list can be reorganized The two most frequently used programs can be saved to the first three positions Select program for position 1 E Senzor Mash s NS E Express l Ss Cancel Continue m Select the program you would like to assign to the first position m Confirm with Continue m Repeat with the second and third positions The selected programs are displayed as programmed To change a program position select back until you reach the respective program position Summary 2 00 re Sensor Wash Express D Back Finished m Whe
4. Delay Start the detergent could leak out of the compartment Att is recommended to add the detergent and lock the dishwasher door to prevent children from coming in contact with the detergent m Select the desired menu from the Main menu m Select Delay start from the Program menu The last set Start time is displayed Sensor Wash 132 h 12 00 Options Start time 10 00 End at 1 32 m Select the desired Start time with the touch controls Holding the button will automatically increase or decrease the time The end time will be automatically adjusted m Confirm with OK Additional options m Select Start sy Sensor Wash 12 00 start at 10 00 Cancel C The program name and start time are displayed At the set time the selected program will start automatically A few minutes after the last key press the dishwasher will switch into standby mode to save energy The display and the indicators will turn off Starting a program before the delay start has elapsed A program can be started before the delay start time has elapsed m Select Cancel and confirm with OK m Select Main menu The display returns to the Main menu The program can now be started 45 Additional options BrilliantLight The dishwasher is equipped with an interior light With the door open the light turns off automatically after 15 minutes The light can also be deactivated m Open and clo
5. OK Memory The memory function allows you to save the last selected program When turning the dishwasher off and on again after a program has finished or opening and closing the door the last selected program is displayed instead of the main menu The function is turned on by default m Select the desired option and confirm with OK 56 RemoteVision Optional accessory To learn more about RemoteVision visit www miele com m Select Y to show module state If i module connected and ready is displayed no further action is required Via the Options menu you can Reboot the module Reset the factory default settings Enter Ad Hoc mode Refer to the RemoteVision section of this manual or the RemoteVision Installation manual for further instructions Settings F Showroom program Demo modes are only for showrooms The dishwasher has various demo programs for showrooms The programs Demo mode and Endless demo mode show the use and function range of the dishwasher Demo mode The program is started by pressing any button It runs once and must be started again Endless demo mode The program starts as soon as it is activated and runs in a loop until it is turned off Demo wash sound The program activates the pumps to demonstrate the wash sound Trade show mode Once the machine is used for the first time this option is disabled in the display Dryi
6. a program 36 Choose your program according to the type of load and soiling The Program guide describes the programs and application m Select the desired program The display changes to the program menu Sensor Wash 132 h 12 00 Options Start time End at Information about the selected program can be displayed by pressing the i button To choose another program use the lt C Clear button to return to the main menu Use Program guide When to use Program sequence Pre rinse Main wash Interim rinse 1 2 Final rinse Drying Pots amp Pans For normally soiled pots amp pans with dried on food and heavily soiled dishware use 120 detergent recommended Normal Program for completely washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware as required China amp Crystal For temperature sensitive glassware and lightly soiled dishware use 50 detergent recommended as requ ired as required SaniWash To sanitize dishware e g baby bottles cutting boards and preparation dishware Extra Quiet Very quiet program for normally soiled dishware with dried on food Rinse amp Hold To rinse dishes when a complete program is not needed Express Quick program for lightly soiled dishware e g party
7. back into the wash cabinet The rinse aid dosage is set too high Clean the drain pump and the non return valve see Cleaning and care Reduce the dosage see Settings Rinse aid Frequently asked questions Dishes are not dry glasses and cutlery are spotted White residue is visible on cutlery and dishes Clouding occurs on glassware and cutlery film can be wiped off Possible fault The rinse aid setting may be too low or the rinse aid reservoir is empty Solution Increase the dosage refill the reservoir or switch the rinse aid product when refilling see Rinse aid Dishes were taken out too soon Leave dishes in longer see Use A Tab product was used These products have a low drying effect Not enough rinse aid was used Change the detergent or refill the rinse aid see Rinse aid Increase the dosage see Setting the rinse aid dosage The salt container is empty Refill the salt container see Filling the salt container The salt container lid was not screwed on properly Reseat it making sure it screws back on correctly Unsuitable Tab products were used Use a different detergent Use normal powder or gel detergent The water softener is programmed on too low a setting Program a higher water softener setting see Water softener 67 Frequently asked questions Glasses have
8. dishwasher to a water hardness below 4 d 4 gr gal Immediately after each refill run the Rinse amp Hold program without the Turbo function without a load This will remove any traces of salt from inside the wash cabinet If using Tab detergent products in your dishwasher the messages can be turned off if desired see Settings Refill display If you switch to using detergent that does not contain salt or rinse aid it is important to remember to replenish the salt and rinse aid and to turn the indicators back on Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware The rinse aid is filled in the reservoir and the set amount will be automatically dosed A Filling the rinse aid reservoir with detergent liquid or powder will damage the reservoir Only pour rinse aid formulated for residential dishwashers into the reservoir m Press on the flap until you hear it When using Tab detergents rinse click shut Failure to close it all the aid is not needed way allows water to enter the reservoir during the wash program Adding rinse aid m Clean any spilled rinse aid This prevents over foaming occurring during the next program You can adjust the rinse aid dosage for best results see Settings Rinse aid m Press the button on the rinse aid reservoir in the direction of the arrow until the flap springs open m Po
9. for 10 place settings Cutlery tray 22 Loading the dishwasher Typical load for 16 place settings Cutlery tray Loading the dishwasher Upper basket N Always use the dishwasher with the upper and lower basket inserted except during the Tall items program if available m Load the upper basket with small lightweight or delicate items such as cups saucers glasses dessert bowls etc Shallow pans can also be placed in the upper basket m Long items such as soup ladles mixing spoons and long knives should be placed lying down across the front of the upper basket 24 Foldable spikes The rows of spikes can be lowered to make more room for larger items such as casserole dishes m Press the yellow lever down and fold down the spikes Hinged cup rack m To make room for tall items raise the rack upwards Glasses can be arranged along the cup rack to give them some support during the program m Lower the cup rack and lean the glasses against it Loading the dishwasher Jumbo cup rack Universal support bar depending on model The support bar will hold tall glasses The cup rack can be set at two different and stem ware securely widths so that it can also accommodate large cups F i A
10. machine without impairing the cleaning result N The water in the dishwasher is hot risk of burns by splashing water Cancel a program only in the first few minutes Otherwise important program steps e g the water softening could be interrupted 40 Time display Before the program starts the time display shows the running time of the selected program in hours and minutes During the running program the remaining time is shown in the time display The current step of the program is identified as shown Pre rinse Soak Main wash Interim rinse Final rinse Drying End The running time for the same program may vary depending on the intake water temperature load size and soiling When a program is selected for the first time a time is shown which equals an average program running time with cold water Each time a program is run the electronic adjusts the program running time according to the intake water temperature and the load size Use Standby A few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy m To turn the dishwasher back on press This feature can also be turned off see Settings Optimize standby The dishwasher will then turn off completely after 6 hours If the Standby setting is turned on and the Display clock is selected see Setting Time of day the clock will only be disp
11. panel m The plastic control panel should only be wiped with a damp cloth or suitable cleaning agent designed for use on plastic VAN The appliance front and controls are not scratch proof Remove spills immediately 72 Exterior m Only use a conditioner suitable for your kitchen cabinetry m Clean wood only with a damp cloth and wipe dry Clean the exterior with a solution of warm water and liquid soap applied with a soft sponge Dry with a soft cloth Glass cleaners may be used to clean the exterior However do not allow them to sit or pudale this can cause damage to the surface Remove the cleaner promptly To better maintain your appliance avoid the following cleaners containing soda ammonia thinners or chlorides cleaners containing descaling agents or lime removers abrasive cleaners stainless steel cleaners dishwasher soap powder caustic oven cleaners scouring pads steel wool hard brushes metal scrapers steam cleaning products Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes It also protects the circulation pump from damage caused by foreign objects e g broken glass bones etc During normal use the filter system is self cleaning ZN The machine must not be used without all the filters in place m Check and clean the filter
12. system periodically for any trapped or foreign objects The level of soiling and time it takes before the filters need cleaning will vary depending on household The display shows Filter check after 50 wash cycles default setting The filter check frequency can be set from 30 to 60 cycles See Settings P Filter check m Check and clean the triple filter m Confirm with OE The display changes to the program menu Cleaning the triple filter m Turn off the dishwasher before cleaning m Turn the handle counterclockwise to release the triple filter system m Remove the triple filter from the machine Clean any solid particles and rinse under running water Scrub with a nylon brush if necessary ZA Be sure that debris does not get into the circulation pump causing it to clog 73 Cleaning and Care To clean the underside of the filter the flap must be opened m Push the clips together and open the flap m Rinse under running water m Close the flap so that the clip engages 74 m Return the filter so it lies flat in the base of the wash cabinet m Lock the filter by turning the handle clockwise N The triple filter system must be inserted and locked Large particles could get in the circulation system and cause blockage Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets The spray arms should be inspect
13. the displayed value To browse between menus The available touch controls light up when active SO On Off button with indicator To turn the dishwasher on or off Display See the following pages for more information lt cC Clear button To switch back to the previous menu level or to discard a selected setting button Information To display more info about the displayed menu Standby indicator The indicator flashes when the dishwasher is turned on but the display is turned off Technical Service interface Allows a service technician to check and update the machine when applicable This operating instruction manual describes several dishwasher models with different indicated settings The different dishwasher models are named Standard 32 81 5 cm high dishwashers XXL 33 1146 85 5 cm high dishwashers Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity For best results follow these tips m For lowest energy consumption you may connect the dishwasher to a cold water source m For fastest possible wash times with slightly higher energy consumption connect the dishwasher to a hot water source m Make full use of the baskets without overloading for the most economical washing m Use the correct amount of detergent and rinse aid Detergent dosage is dependent upon the amount o
14. 5381 905 660 9936 Fax 905 532 2290 www miele ca professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercare miele ca general and technical enquries Alteration rights reserved 1511 G5910 G5915 CE M Nr 07 909 210 02 INFORMATION IS SUBJECT TO CHANGE PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS TECHNICAL amp WARRANTY INFORMATION
15. 7 62 60 61 70 63 73 70 49 Settings f Rinse aid For best results the rinse aid dosage can be adjusted The dosage can be set between O and 6 ml The dosage set by default to 3 ml of rinse aid per program Use a higher setting if spots appear on dry glassware Use a lower setting if streaking appears on dishes or glasses m Selected the desired rinse aid amount and confirm with OE 50 Adjust Sensor Wash The Sensor Wash program can be adjusted to clean stubborn but normal soiling m Select Wes and confirm with OK Drying Plus To improve the drying process the door will open except during the Extra Quiet program at the end of the program during the drying phase This feature can be turned off m Select the desired setting and confirm with OE Mif you turn the Drying Plus function off and still want to open the door at the end of a program then open the door completely Otherwise steam can damage the countertop edges because the fan will continue to run Settings F Optimize standby A few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy This function can also be turned off The dishwasher will then turn off completely after 6 hours m Select the desired setting and confirm with OE If the Standby option is turned on the clock will only be displayed for a few minutes
16. _ A Operating Instructions Dishwasher G 5910 G 5915 To prevent accidents en US CA and appli damage read thes tructions before installation or use M Nr 07 909 210 Contents IMPORTANT SAFETY INSTRUCTIONS 4 Guide to the dishwasher 0 000 00 8 Control panel i ccserasee tado sees tan aaa bene wea dayne de 9 Caring for the environment ooo 10 Before using for the firsttiMe ooo oococccoco 11 TG Open te GOGO ea aria a eee e ied ba a eS 11 To close ME eetset bud id ed dens 11 Child Safety LOCK os 2er teat toe ete it bq a 11 Display ista ide cence onc Aen Relay a oh a pee em aad 12 Filling the salt container 2 eee 16 Salt refill message 2 ett IZ RINSE sc ht ate na de EDE EENE ERREPA enna peda hE Same 18 Adding NSE Ad ica ae naan beads MEW ae Abe On ek Oa eR ee alee 18 Rinse aid indicator serres 4 PAG a Pa ed dae be eee ended des 19 Loading the dishwasher 0 0 ee 20 Items not recommended for dishwashing sasaaa aaa e eee eee 21 Typical load for 10 place settings ooooooococco eee 22 Typical load for 16 place settings o oooooooooooo eee 23 Upper basket 05 0 etauete ais dre ta epi lia ela 24 Eowenbaskblia tl tano ana oi ahaa aces aay ye eet idos 28 CUE eco nao nal ca a it aia citadas Uned 31 Optional accessories 33 A ihd 4 ene is 34 Addig det rgent at tine doe ddd ede GL Rad Babee hee Ad o 35 TOG Oe sone e
17. a brown or blue discoloration film cannot be wiped off Glasses are dull and discolored film cannot be wiped off Tea or lipstick stains have not been completely removed Plastics are discolored There are rust stains on cutlery 68 Possible fault Detergent deposits Glasses are not dishwasher safe The surface is affected The wash temperature of the selected program was too low Solution Change detergent right away There is no remedy Only use dishwasher safe glasses Select a program with a higher wash temperature The detergent has a low bleaching effect Natural dyes e g from carrots tomatoes or ketchup may be the cause Not enough detergent was used to break down natural dyes The affected items are not corrosion resistant Use a different detergent Use more detergent see Detergent Discoloration is permanent There is no remedy Use only dishwasher safe cutlery No program was run after refilling salt Salt residuals got in the wash cycle Start the Express program without a load after refilling salt without the Turbo option The salt container lid was not screwed on properly Reseat it making sure it screws back on correctly After sales service Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet m Please quote the mo
18. a aaaea ccc eee 63 SR er anetnee ee 65 Poor cleaning resul erres chee eke ha a ae REA ae he EENES 66 After sales Services iron sewed he fee em ea dees oye ed 69 Transpo gi 6 oir wi Oa 70 User Maintenance Instructions 000 000 eee ee 71 Cleaning and Care 72 Triple filter system 2 0 ete 73 Cleaning the drain pump and non return valve n asaan ee 76 Installation instructions 0 uaaa eee ce Help to protect the environment 78 Electrical connection 0 0000 79 PIUMDINO a i naar pdas hc lace cde cae Gg pias 81 Connection to the water supply 0 eee 81 A A Meena e bow eed aa 82 IMPORTANT SAFETY INSTRUCTIONS WARNING When using your dishwasher follow basic precautions including the following Read all instructions before installation or use of the dishwasher to prevent injury and machine damage Use the dishwasher only for its intended purpose This appliance is intended for residential use only Keep these operating instructions in a safe place and pass them on to any future user Correct usage P gt The dishwasher is not designed for commercial use It is intended for use in domestic households and in similar working and residential environments such as shops offices and showrooms or guest houses P The dishwasher is not intended for outdoor use P It must only be used as a domestic appliance as specified in these operating instructions for cle
19. ainers on the base of the cutlery tray HAARE to ensure that water runs off them a freely The upper spray arm must not be m You can use the yellow slide to adjust blocked by tall cutlery items e g the height of the middle section of the cake servers cutlery tray to make more room for large items of cutlery The side sections of the tray can be moved into the middle to accommodate tall dishware items in the upper basket 31 Loading the dishwasher Cutlery basket m Fit it onto the cutlery basket if required The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket m To avoid risk of injury knives and forks should be placed with the handles upwards in the basket However cutlery placed handle down in the basket will come out cleaner and drier m Place small items of cutlery in the individual slots on three sides of the cutlery basket m Insert cutlery with the handles facing Cutlery insert for the cutlery basket downwards and distribute them evenly along the insert Use the insert supplied for heavily soiled items of cutlery The insert separates the items so that they can be reached better by the spray jets 32 Optional accessories Optional dishwasher accessories are available from your Miele dealer Miele or Mieleusa com depending on your model some may already be supplied with your machine as standara If you would like to the followin
20. all items are securely positioned m Hollow items such as cups and glasses should be placed upside down in the baskets m To ensure good water coverage tall narrow and hollow items e vases or champagne glasses should be placed in the center of the basket rather than in the corners m Concave based items such as mugs or bowls should be placed at an angle so that water does not pool 20 m The spray arms must not be blocked by items that are too tall or hang through the baskets Check clearance by manually rotating the spray arms Place very small items in the cutlery tray or basket so they do not fall to the bottom of the wash cabinet Food residue and spilled liquids should be cleaned from the sides of the dishwasher door These are outside of the wash cabinet and are not cleaned by water from the spray arms Loading the dishwasher Items not recommended for dishwashing Cutlery with wooden handles Wooden cutting boards Glued items such as old knives with handles glued together around the shank of the blade Handmade craft items antique metal trimmed or decorative glassware Plastic items that are not heat resistant Copper brass tin or aluminum Dishes with color painted over the glaze These dishes may fade over time Fine glassware and crystal items should only be washed using the China amp Crystal program Otherwise clouding or etching may occur af
21. alt to the machine to achieve optimal cleaning results and ensure long term functioning of the water softener 16 m Remove the lower basket from the wash cabinet and unscrew the salt container lid When opening the salt container water will run out Open the container only to refill salt Important The salt container must be filled with 2 quarts 2 of water before adding salt for the first time so the salt can dissolve properly Water does not have to be added with subsequent refills Before using for the first time m Place the provided funnel over the salt container and carefully fill it with salt The salt container holds approx 4 4 lbs 2 kg of salt depending on the type of salt m Clean any excess salt from the threads of the container opening Screw the lid on firmly m Immediately after each refill run the Rinse amp Hold program without the Turbo function without a load This will remove any traces of salt from inside the wash cabinet Salt refill message m When the display shows Insufficient salt refill the salt after the program has finished m Confirm with OF The message will clear from the displa If a sufficiently high concentration of y salt has not yet formed the Insufficient salt message may continue to be displayed after adding the salt In this case confirm again with the center button The Insufficient salt message is turned off if you have programmed the
22. aning domestic crockery and cutlery Any other usage is not supported by the manufacturer and could be dangerous gt Persons who lack physical sensory or mental abilities or experience with the appliance should not use the dishwasher without supervision or instruction by a responsible person 4 Electrical Safety gt Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt gt Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse gt Do not use an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician gt If the supplied power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord P The outlet must be acc
23. c foe cb Stare se Rain Emp ad ay wae SG Ae RR ac ae oe 36 Selecting a Programi seges pira ratos clara olla see een ee tes 36 Selecting options 2 0 tte 39 Starting 2 PrOGlaM sis 0 nts aek o ede ae RP Ye PEs Sade de 40 THING Aslan la Rc a age ee ee ae ae n 40 ln ate cat Ban eae ea eee eg ane Mek Hae eae bey eee 41 Atthe end of a programs se cota e Ea ee 41 Preparing your appliance for an extended Vacati0N o o o ooo o oo omo 42 Interrupting a PrOgraM occ 42 Changing a program 2 tte 43 Contents Additional options 0 0 00 0 eee 44 Delayistalto amos adam nad ads Oa dented Raed eet da tos een 44 Flea GEM gr casera A A Seda ean eee ada ea enar steep cle 46 A eo Pee i bes Feat 47 Water NANINGSS ieee ces aim A it 49 DINOS orcos taa sta tarada etme eee ma 50 Optimize standby 2 0 0 0 aie keget E eaS E E E E 51 Refil diS plaY recre tenne era paee DE eS Gea ees aw R E 51 CHECK TNMGIS 2 torta ardid adn 51 Reorganize Programs ee red tagia e Dira de rl dde do 52 SAVE OPUONS Leotardo diria 53 Child Safety LOCK s ecccneud ent ee oye aa ede ews Dae e aa ea 54 VOUI G Se eaea mee O ohn th Speen accom este a aE e E 55 Factory default 0 0 0 eee 57 ReEMOtleVISION cours ta a da nan athe payee el de 58 Frequently asked questions 0 oo 59 Technical TANS 6 5 oblate Sd dou deb dai bh bend deed 59 Problems water intake drain 2 0 eee eee 61 General problems with the dishwasher n a aas
24. conds Turn the dishwasher on Select the desired program Close the door Select Start If the problem persists contact Technical Service Waterproof fault Fro The waterproof system has activated Turn off the water supply Contact Miele Technical Ser vice Automatic door closing fault F32 The door may be blocked Remove the item if necessary restart the program If the message shows again contact Miele Technical Ser vice Automatic door opening fault F33 60 Possible technical fault Open the door by hand and restart the program If the message shows again contact Miele Technical Ser vice Frequently asked questions Problems water intake drain Problem The buzzer sounds The display shows the following Ho water intake Open the water faucet Fault water intake Fiz 13 Possible fault The water supply is closed Solution Open the water supply all the way Before fixing the fault Turn the dishwasher off by touching the control Fault F12 F13 Fault in the water intake Open the water supply all the way and restart the program Clean the water intake filter see User Maintenance Instructions The water pressure at the water connection is lower than 4 35 psi Consult a plumber 61 Frequently asked questions In the program Energy Saver the following fault is displayed Water intake
25. d if a fault occurs Buzzer at the end of a program The buzzer at the end of a program sounds five times in intervals with a brief break in between The buzzer sounds up to one hour if the dishwasher in not turned off Buzzer in case of a fault The buzzer for a fault sounds continuously The buzzer sounds up to two minutes if the dishwasher is not turned off or the fault is fixed The buzzer for a fault cannot be set to off Buzzer tone The buzzer volume can be set to 7 different levels The buzzer cannot be turned off in case of a fault m Select the desired volume m Confirm with OF Night time buzzer tone You can set the buzzer tone used at night to a different volume m Select the desired volume m Confirm with OF Night time The buzzer can also be turned off during the night time hours m Select Start time m Set the start time using the touch controls confirm with OE m Select End at m Set the end time using the touch controls confirm with OE m Confirm with OF Keypad tone A tone will sound when a button is pressed The volume can be set to 7 different levels m Select the desired setting and confirm with OF 55 Settings Brightness The display brightness can be adjusted in 7 levels m Select the desired brightness and confirm with OK Contrast The display contrast can be adjusted in 7 levels m Select the desired contrast and confirm with
26. del type and number of your appliance These can be found on the data plate along the right edge of the door PC Update The Program Correction PC allows a technician to update the dishwasher to make use of new technology When for example technological developments offer advanced modifications to your existing program cycles a service technician will be able to input these into your machine controls via the indicator light marked PC Miele will provide information when such possibilities become available MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by Miele s Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your app
27. dishware or to remove salt traces from the wash cabinet after refilling salt not suitable for detergent tabs Heavy Soil For heavily soiled dishware with dried starchy food Light For lightly soiled dishware e g party dishware 37 Use Program guide When to use Program sequence Pre rinse Main Interim Final Drying wash rinse rinse 1 2 1 2 Energy Saver The water intake temperature X X X X must be 115 F 45 C for light to normally soiled dishware Sensor Wash Sensor controlled program for as X as required X X normally soiled dishware requ ired Starch Cheese For dishware with dried on X X X X X starchy or cheesy food 120 detergent recommended Plastics To gently clean dishwasher X X X X X safe plastics and plastic toys Tall Items For extra large heat resistant X X X X X items e g large vases Remove upper basket Glass no rinse aid For a quick cleaning of X X X cold glassware for direct reuse use without detergent and rinse aid Glass no rinse aid To wash glassware without X X X warm detergent and rinse aid rinse cycle with warm water Usage Electric 0 01 1 3 kWh Water 1 1 5 gal 4 19 1 38 Use Selecting options Options can be added to the selected program m Select the Options menu The display shows the available options for the selected program Available opt
28. ed and cleaned every 4 6 months m Turn off the dishwasher before cleaning Removing the spray arms m Remove the cutlery tray if present m Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm m Pull the lower spray arm firmly upwards to remove m Lift up the middle spray arm to engage the ratchet and unscrew the m Use a pointed object such as a spray arm toothpick to push food particles into m Remove the lower basket the spray arm jets m Rinse thoroughly under running water m Return the spray arms and check that they rotate freely 15 Cleaning and Care Cleaning the drain pump and non return valve If the dishwasher is not completely drained at the end of a program the drain pump or non return valve may be blocked m Turn off the dishwasher and pull the plug m Remove the triple filter see Triple filter system m Use a cup or bowl to scoop water out of the wash cabinet m Tilt the locking clamp to the side m Pull out the non return valve and rinse it under running water m Remove all foreign objects from the non return valve 76 The drain pump is beneath the non return valve see arrow m Remove all foreign objects from the drain pump glass or bone splinters m Before returning the non return valve check that the drain pump is not blocked Spin the propeller several times in both directions to check for obst
29. ed on the clock will only be displayed for a few minutes Display Time of day m Select Display m Select the desired setting and confirm with OK Setting the clock format m Select Format m Select the desired clock format and confirm with OK Set the time of day m Select Set manually m Set the hour with and confirm with OE Set the minutes and confirm After confirming the minutes with OK the display will revert to the previous menu m Select lt C to go back to the Settings F menu Settings F Water hardness re d r gal Setting in displa Your dishwasher is fitted with a water ae g Pey softener which you need to program to a a the water hardness level in your area 3 3 3 see Before the first use 4 4 4 5 5 5 m Turn the dishwasher on O 6 6 6 a 7 7 7 If the memory function is on the 8 8 8 program menu instead of the last 9 9 9 selected program will be displayed 10 10 10 see Settings Memory If this is the a i 2 case use the lt C button in the main 13 13 13 menu 14 14 14 15 15 15 m Select Mater hardness from the 16 16 16 Settings F menu 17 17 17 18 18 18 The set water hardness is marked E gt with a check w A E ES 22 22 22 m Select the water hardness of your 23 23 23 local water supply confirm with OK 24 25 24 25 26 25 26 27 26 27 28 27 28 29 28 29 30 29 30 31 30 31 32 31 32 33 32 33 34 33 34 35 34 35 36 35 36 37 36 37 45 38 46 45 46 60 4
30. een wire ground connect to E N After attaching the permanent power supply cord check that all screws on the terminal block and the strain relief are tightened Plumbing Connection to the water supply ZN Installation repairs and other work by unqualified persons could be dangerous Do not drink water from the dishwasher The dishwasher can heat its own water to the temperature required by the wash program This allows for connection of the machine to either a hot max 140 F 60 C or cold water source For lowest energy consumption and for fastest possible wash times connect the dishwasher to a hot water source All programs use hot water in the rinse cycles To use the Energy Saver program a hot water connection of minimum 115 F 45 C and maximum 140 F 60 C water intake temperature is necessary The higher the water intake temperature the better the cleaning and drying results The inlet hose is approximately 5 ft 1 5 m long The water inlet hose comes equipped with an inlet hose ending with a 3 8 female compression fitting This can be directly connected to a water supply valve or to an appropriate coupling If not connected directly to a water supply valve an appropriate adapter not included is required Water pressure Must be between 4 5 145 psi 0 3 10 bar If the water pressure if lower a Water Intake no
31. er off Then Clean the spray arms See User Maintenance Instructions 63 Frequently asked questions Detergent is left in the dispenser at the end of a program The detergent lid cannot be closed properly The door and the interior walls are still wet after a program has finished Water remains in the wash cabinet at the end of a program 64 Possible fault The dispenser was damp when detergent was added Detergent residue is blocking the catch This is not a fault It is the normal operating mode of the drying system Solution Dry the dispenser before adding detergent Remove the residue The moisture will evaporate after a short time Before fixing the fault Turn the dishwasher off The triple filter in the wash cabinet is clogged Clean the triple filter See User Maintenance Instructions The drain pump or the non return valve may be blocked Clean the drain pump and the non return valve see the User Maintenance Instructions The drain hose is kinked Remove any kinks from the drain hose Frequently asked questions There is a knocking noise in the wash cabinet There is a rattling noise in the wash cabinet There is a knocking noise in the water line Possible fault The spray arm is hitting an item in the basket Items are not secure in the wash cabinet Solution Interrupt the program rearrange
32. essible at all times after installation to disconnect the dishwasher IMPORTANT SAFETY INSTRUCTIONS Installation gt The dishwasher must be installed and connected in accordance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty gt Do not install or use a damaged dishwasher A damaged appliance is dangerous Unplug the machine and contact the Miele Technical Service Department P Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation P This appliance must not be used in a non stationary location e g on a boat gt A WARNING Fire hazard Do not cover or crush the plug of the appliance Ensure that the cabinet opening for the dishwasher provides ample space for the plug and cord Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which could cause overheating gt This dishwasher should only be installed under a continuous counter top secured to adjacent cabinetry P Do not install this dishwasher beneath a cooking surface oven or any appliance that radiates heat High temperatures from these units may damage the dishwasher P A toe kick must be used with the dishwasher If the supplied toe kick is not used a cabinet matching t
33. f soiling and type of dishware being washed See the Program Guide for more information m When using powder or gel detergent reduce the amount to of the normal amount when washing a small load m Choose a program that best suits the degree of soiling and the type of dishes being washed 10 Before using for the first time To open the door The door will open automatically at the end of the program to aid in the drying process This function can be deactivated see Settings Drying Plus m Press the release catch inside the door grip If the door is opened during operation the dishwasher will stop running Once the door is closed the program will restart Keep the opening area free of obstructions To close the door m Push the baskets in m Lift the door and push until the catch engages The door will then close automatically Keep fingers and other body parts away from the door as it is closing Danger of injury Child Safety Lock The Child Safety Lock is designed to prevent children from opening the dishwasher m To lock the door push the slider below the door grip to the right m To unlock the door push the slider to the left Before using for the first time Display The following can be selected in the display the wash program the options the start time the settings menu f information During a running program the display s
34. g accessory will need to be ordered wash a Miele Cappuccinatore a Cappuccinatore insert for the upper basket wash additional items of cutlery a cutlery basket for the lower basket wash long stemmed glassware MieleCare Collection a glassware rack for the lower basket Miele branded cleaning and care products including dishwasher salt detergent and rinse aid are available to order from your Miele dealer Miele or the on line Miele store www mieleusa com 33 Use Detergent Dishwasher detergents contain irritant and corrosive ingredients Avoid inhaling or swallowing dishwasher detergent Keep children away from detergent Keep detergent out of the reach of children Keep children away from the dishwasher when the door is open There could still be detergent residues in the dishwasher Only add detergent just before starting the program and lock the door with the child safety lock depending on model Only use detergents formulated for domestic dishwashers Use only the recommended amount of detergent Continued use of too much detergent may cause machine damage When using the China amp Crystal program depending on model reduce the amount of detergent used to at least Y of the normal dosage Also make certain your china and crystal are dishwasher safe 34 You can use powder gel or tab detergents Follow the dosage information on the de
35. harp items pointing downwards to prevent injuries gt Only use detergents and rinse aids recommended for residential dishwashers Keep all detergents and rinse aids out of the reach of children P Do not inhale or swallow detergents Dishwasher detergents contain irritant and corrosive ingredients They can cause burning in the mouth and throat if swallowed or inhibit breathing Consult a doctor immediately if detergent has been swallowed or inhaled B Do not drink water from the dishwasher Harmful residues could be present gt Do not fill the rinse aid reservoir or salt container with detergent It will destroy the rinse aid compartment and water softener gt If the supplied power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord The outlet must be accessible at all times after installation to disconnect the dishwasher P gt This model offers a Drying Plus feature i e the door will automatically open without an audible signal first being given at the end of the program releasing warm air from the dishwasher Use caution the air may be hot IMPORTANT SAFETY INSTRUCTIONS P gt This model offers a Drying Plus feature e the door will automatically shut once close enough to engage the catch P gt Advise the user of the Drying Plus feature to avoid injuries by walking bumping or knocking into the partially opened door gt Supervise childre
36. he desired setting and confirm with OE Before using for the first time Time of day setting The display changes automatically to the time of day setting Time of dar 10 Pa m Set the hours using the controls and confirm with OK Set the minutes and press OK Display The display changes automatically to the screen for setting the time of day display Time of dar Do not display w On On for 60 seconds m Select the display desired for the time of day confirm with Water hardness The display then changes to the water hardness setting Water hardness 15d Y 167d a 17d 14 Before using for the first time To achieve good cleaning results the dishwasher needs soft water Hard water results in calcium deposits on dishware and in the dishwasher If your tap water hardness is above 4 d 4 gr gal US the water should be softened Your local water authority will be able to advise you of the water hardness level in your area The dishwasher must be programmed to correspond to the water hardness in your area In areas where the water hardness fluctuates e g 37 50 d 39 52 gr gal always program the machine to the higher value in this example 50 d 52 gr gal If there is a fault it will help the service technician to know the hardness of your local water supply Please note your water hardness below d gr gal The water hardness was progra
37. hows the program name the current time of day the program sequence the approximate remaining time faults and messages To save energy the dishwasher turns off after a few minutes if no button is pressed To turn the dishwasher back on press 12 A bullet in the display next to the touch control shows that this function can be selected The corresponding touch control is also illuminated r le The arrows in the display indicate that more selections or text follow and can be displayed with the respective illuminated touch control A dotted line is shown to indicate the last selection available Ok To confirm these messages or settings select OK and the next menu or another menu level will appear wa The currently selected option is marked with a check The Settings Ff menu allows you to customize the dishwasher settings See Settings for more information Before using for the first time Welcome screen Language Clock format m Turn the dishwasher on The Welcome screen shows when the washer is turned on for the first time The display changes automatically to the language setting Sprache y cestina E dansk D deutsch m Select the desired language and confirm with OK The selected language is marked with a Y check The display changes automatically to the clock format 5 Clock Format 12h clock 24 h cock s m Select t
38. ions Turbo For shortening the program duration To achieve optimum results energy consumption rates will increase When the Turbo function is used in correlation with a program a quick rinse is completed without heating Use when a complete program is not needed Pre rinse For easily removable soiling Soak To soak stubborn soiling When using powder detergent fill approx 1 teaspoon 5 g of detergent in detergent compartment I Extended drying To enhance drying of odd shaped dishware and plastic items Intensive lower basket For washing heavily soiled dishes in the lower basket at the same time as delicate items in the upper basket This function will increase the cleaning power in the lower basket in programs which it is selected Depending on the program the run time may be extended slightly Once this function is set for a program it will remain active for that program until the setting is changed m Select the desired options The selected options are marked with a Y check m To de select an option press the respective touch control again m Confirm the selected options with OK The display changes back to the program menu The message Options selected will appear in this display 39 Use Starting a program m Select Start The program starts and Items can be added appears in the display As long as this reference is shown tableware can be added to the
39. items blocking the spray arms Interrupt the program and rearrange loose pieces A foreign object has become lodged in the drain pump This may be caused by the installation or the diameter of the pipe Remove the foreign object from the drain pump see Cleaning the drain pump and non return valve This has no effect on the dishwasher If in doubt contact a plumber 65 Frequently asked questions Poor cleaning results Problem The dishes are not clean Glasses and cutlery show streaks The glasses take on a bluish shimmer the deposits can be wiped off 66 Possible fault The dishes were not loaded correctly Solution See Loading the dishwasher The program was not powerful enough Select a more intensive program see Program Guide Stubborn but normal soiling e g coffee tea Use the function Adjust Sensor Wash depending on model see Settings Not enough detergent was dispensed Use more detergent or change the detergent The spray arms are blocked Turn the spray arms and rearrange the dishes if necessary The triple filter in the wash cabinet is clogged or not correctly inserted The spray arm jets might be clogged as a result Clean the filter and insert it correctly Clean the spray arm jets if required see Cleaning and care The non return valve is stuck open and blocked Wash water will run
40. layed for a few minutes If refill salt and or rinse aid or a fault are present in the display the dishwasher will not turn off The refill messages can be turned off when you use a tab detergent see Settings Refill display Fault messages cannot be turned off At the end of a program At the end of a program the display shows Prograrn finished or Drying plus with the door slightly open if activated In the Express program the drying fan will run for a few minutes after the program is completed Dishes tend to chip if removed still hot from the dishwasher If the automatic door opening setting is deactivated see Settings Drying plus it is recommended to open the door manually to allow tableware to cool much faster m Turn the dishwasher off m The dishes can now be removed Unloading the lower basket first will prevent water drops from the upper basket and cutlery tray depending on model from dropping onto dishes in the lower basket m Push the baskets in The dishwasher continues to use electricity until turned off with the O button After a few minutes the dishwasher will turn off automatically 41 Use Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time please note that this may not be enough to reduce the risk of a leak To be completely safe you must turn off the water supply to each i
41. liance dealer or visit us online at http mieleusa com mielecare 69 Transport To transport the dishwasher e g when moving to a new home note the following Empty the dishwasher Secure any loose parts e g hoses cables cutlery baskets Transport the dishwasher in the upright position If unavoidable it may be transported on its back Do not transport it on its side or on the door Residual water in the machine could leak and cause electrical damage 70 User Maintenance Instructions To prevent accidents and appliance damage read these instructions before installation or use Cleaning and Care Check and clean your dishwasher regularly This will help avoid problems and faults N Abrasive cleaning agents all purpose cleaners thinner or ammonia based cleaners should not be used on the dishwasher They will damage the surface Wash cabinet Generally the wash cabinet is self cleaning if the correct amount of detergent is used The wash cabinet can be cleaned with a dishwasher cleaner such as Dis Cleaner available from your Miele dealer or online at www mieleusa com Door and the door seal m Wipe the door seals regularly with a damp cloth to remove food deposits m Food residue and spilled liquids should be wiped from the sides of the dishwasher door These are outside of the wash cabinet and are not cleaned by water from the spray arms Control
42. mmed at 1 d 1 gr gal by factory default m Select the hardness of your water supply and confirm with the center button See Settings Water hardness for more information Two notes appear in the display After confirming these notes 1 Add rinse aid and or Add salt may appear in the display Confirm these notes with OK The display changes to the main menu These basic settings are saved after the first full program cycle is completed Before using for the first time Every dishwasher is tested before leaving the factory Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used Filling the salt container To achieve good cleaning results the dishwasher needs soft water water that is low in minerals Hard water results in calcium deposits on dishware and in the dishwasher Therefore if your tap water hardness is above 4 d 4 gr gal the water should be softened The built in water softener is designed for this purpose The water softener is suitable for a water hardness up to 70 d 73 gr gal ZN inadvertently filling the salt container with dishwashing detergent including liquid detergent will damage the water softener Only use water softener salt specially formulated for dishwashers Other salts may contain insoluble additives which can impair the water softener If using Tab products which include salt still add s
43. n near the dishwasher to ensure fingers or other parts of the body are not caught when the Drying Plus feature is in operation gt Dishes can be very hot at the end of a program Allow the dishes to cool until they are cool enough to handle before unloading them P The water supply must be turned off when the appliance is not used for a longer period of time e g during vacations Disposal of an appliance gt If the appliance is removed from its installation site and will not be used remove the doorlock to the wash cabinet to prevent children from locking themselves in the machine SAVE THESE INSTRUCTIONS Guide to the dishwasher O W Upper spray arm not visible Triple filter system 2 Cutlery tray Data plate 3 Upper basket Child Safety Lock in the door handle not visible Middle spray arm Air inlet for drying 40 Rinse aid reservoir depending on model Dual compartment detergent Lower spray arm dispenser 42 Salt container Guide to the dishwasher Control panel 000 m 0 RemoteVision Indicator for RemoteVision enabled appliances E Selection touch controls To select a menu point displayed next to the touch control To change
44. n you are done reorganizing the program list confirm with Finished 52 Settings F Save options Additional options can be selected for some programs e g extended drying See Use Selecting options Save options allows you to save the selected options for future use of the program This function is turned off by default m Select the desired setting and confirm with OE 53 Settings F Child Safety Lock The Child Safety Lock protects the dishwasher from misuse If the dishwasher is turned on while the Child Safety Lock is activated the display shows The appliance is locked The lock must be deactivated before the dishwasher can be used As long as the Child Safety Lock is activated the dishwasher is locked every time it is turned on The function is turned off by default m Select the desired setting and confirm with OE Unlocking the dishwasher m Turn the dishwasher on The message The appliance is locked shows m Confirm with OE Deactivate the Child Safety Lock m Select Yes Child Safety Lock EJ The appliance is unlocked The dishwasher is unlocked and ready to use 54 Settings F Temperature The temperature can be displayed in C Celsius or F Fahrenheit The temperatures are shown in C Celsius by default m Select the desired temperature unit and confirm with OF Volume When the buzzer is activated a tone sounds at the end of a program an
45. ndividual appliance This means under the sink for a dishwasher at the laundry bib for your washer etc 42 Interrupting a program A program is interrupted as soon as the door is opened If the door is closed the program will continue from where it was interrupted N Open the door with care The water in the dishwasher is hot Danger of scalding Before closing the door again leave it ajar for approx 20 secs This will enable the temperature in the wash cabinet to settle Close the door firmly until it clicks into place Use Changing a program If the detergent flap is already open do not change the program If a program has already started and you wish to change it Mm Sensor Wash ALTA tems can be added Time left 1 10 h Cancel C m Select Cancel and confirm with OK The program is canceled 05 Sensor Wash Program finished Wain menu C m Select Main menu The display changes to the main menu m Select the desired program m Select Start 43 Additional options Delay start 44 The starting time of a program can be delayed between 15 minutes and 24 hours The start can be delayed in 15 minute increments When using the Delay Start function make sure that the detergent compartment is dry before adding detergent use a cloth if necessary The detergent might stick together and not get completely rinsed out Do not use liquid detergent when selecting
46. ng Plus Cerna The door opens automatically Turning the Showroom program on m Select the desired option confirm with OK m Confirm the following messages with OK m Press any button to start the selected demo mode m To cancel the demo mode press any button again and confirm with OK Turning the Showroom program off m Select Off to deactivate the Showroom program and confirm with OF m Confirm the message Deactivate demo mode with OK Factory default All settings can be reset to factory default m Confirm the message Reset to factory default with OF m Confirm the information All settings are reset to factory default with OK Leaving the Settings menu m To leave the Settings Fr touch the Clear lt C control The main menu appears 57 RemoteVision Miele s RemoteVision Wi Fi technology creates a virtual link between your appliance and our monitoring center If a fault occurs Miele s client service center will be notified and contact you or another trusted individual identified on your call roster in order to gain access to your appliance to fix the problem For information on set up and installation of the RemoteVision module see the separate RemoteVision installation manual 58 Be sure your wireless system meets the following requirements A wireless router that supports an IEEE 802 11b protocol Windows XP or newer operating system Mac OS X 10 3 or highe
47. nsions can be accommodated 27 Loading the dishwasher Lower basket m For larger and heavier items such as plates serving platters saucepans bowls etc Glasses cups small plates and saucers can also be arranged in the lower basket Dishwasher with cutlery tray m Place large platters and dishes in the center of the lower basket When tilted plates up to 13 3 4 35 cm in diameter can be accommodated f PV m Hi 0 SS S SSS SSS SSS SS 28 Loading the dishwasher Removable MultiComfort insert Glass rack The rear section of the lower basket is m The glass rack can be raised to make used for cups glasses plates pots more room for tall items enel yas m Stem glassware e g wine glasses You can remove the MultiComfort insert champagne flutes or beer glasses to provide more space for larger items can be leaned against the glass rack such as pots and pans or suspended from it The height of the glass rack is adjustable To remove the insert m Press the yellow handle forwards and remove the insert m Slide the glass rack to the desired height until the catches click into lace at the top To replace the insert p m Slide the hooks of the insert under the struts of the lo
48. oe kick must be installed gt Do not install the dishwasher in an area where it will be exposed to temperatures below freezing P Do not cut the intake hose or submerge it in liquid This hose contains electrical components that could cause injury or property damage if cut or submerged P gt Only power up the dishwasher when all installation and plumbing work is complete IMPORTANT SAFETY INSTRUCTIONS Use P To reduce the risk of injury do not allow children to play in on or near the dishwasher It is possible for small fingers may be pinched in the door B Only use the dishwasher if all panels are properly in place P gt Do not tamper with the controls gt Do not sit or stand on the door or baskets of the dishwasher Close the door when not in use gt Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period turn on all hot water faucets and let water flow from each for several minutes before using the dishwasher This will release any accumulated hydrogen gas Do not smoke or use an open flame during this time P Be sure that all items placed in the dishwasher are dishwasher safe For items not labeled check the manufacturer s recommendations B When loading tableware place sharp items away from the door to prevent damage to the seal Load s
49. r Cable or DSL modem Microsoft Internet Explorer 6 or higher Safari 2 0 or higher Firefox 1 5 or higher Please note that each wireless router manufacturer supplies their own device drivers and setup programs Due to the differences in manufacturers exact router setup instructions are not included in this manual Wording and instructions may vary Frequently asked questions With the aid of the following guide minor problems can be fixed without a service call Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage Technical faults Problem After the dishwasher was turned on the display stays off and the stand by indicator does not flash The dishwasher stops during a program Possible fault The machine is not plugged in Solution Insert the plug The fuse has tripped The fuse has tripped Reset the circuit breaker See data plate for minimum Reset the circuit breaker See data plate for minimum amperage 59 Frequently asked questions The buzzer sounds The display shows the following Technical fault Fas Contact Technical Ser wice Possible fault There may be a technical fault Solution Before trying to remedy the fault Open the door Turn the dishwasher off with the O button After a few se
50. ructions m Carefully reinsert the non return valve and secure it with the locking clamp N Make sure the locking clamp clicks into place Installation Instructions Please refer to the Installation Diagram supplied with these instructions To comply with IEC sound testing protocols please contact Miele for additional instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping These materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation 78 Disposal of an old machine Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Ensure that the appliance presents no danger to children while being stored for disposal Before discarding an old appliance unplug it from the outlet cut off its power cord and remove any doors to prevent hazards Electrical connection ZN Installation repairs and other work by unqualified persons could be dangerous Check that the voltage frequency and fuse rating shown on the data plate ma
51. se the door quickly 3 times The door must be opened enough so that the interior lighting turns on then off From now on the interior lighting is turned off m To turn the light on again repeat the above process 46 Settings F The Settings Ff menu allows you to adjust standard settings Opening the Settings menu m Turn the dishwasher on The main menu shows in the display If the memory function is selected the last selected program is displayed See Settings Memory Switch to the main menu by pressing Clear lt C hain menu m Select Settings F The display changes into the menu Settings P Settings Language y Time of day Mater hardness m Select the menu option you would like to change Press the i button to see more information about the option currently selected The selected options in the submenus are marked with a check V 47 Settings Language The display contents can be shown in different languages The displayed language can be changed by the submenu Language P m Select the desired language and confirm with OK The flag behind the word Language P serves as a guide when an unfamiliar language is selected Select the respective menu with a flag until the submenu Language P appears 48 Time of day This selection allows the clock to be shown as 24 or 12 hours The clock can also be set from here If the Standby option is turn
52. tch the household mains supply The power outlet must be accessible after installation Do not use an extension cord to connect the dishwasher to the mains Danger of overheating See data plate on the right side of the door A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician or a qualified technician GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances A Improper connection of the equipment grounding conductor can result in electric shock Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply please consult a licensed electrician or call Miele s Technical Service Department 1 800 999 1360 1 800 565 6435 Specifications The dishwasher comes equipped with a 4 ft 1 2 m power cord with a molded plug for connection to 120 V 60 Hz 15 A grounded receptacle
53. temp too low The buzzer sounds The display shows the following error message Drain fault F11 62 Possible fault The intake water does not have a minimum temperature of 115 F 45 C See Plumbing Solution Restart the program If the fault is displayed again use a different program Before fixing the fault Turn the dishwasher off with the button Fault in the water drain There might be water in the wash cabinet Clean the triple filter Clean the drain pump and the non return valve See User Maintenance Instructions for more information on the above Remove any kinks in the drain hose Frequently asked questions General problems with the dishwasher Problem The display is dark The interior lighting is not turned on when the door is opened The buzzer sounds The display shows the following error message Middle spraw arm blocked or Lower spraw arm blocked Possible fault The dishwasher has gone into Standby mode to save energy The interior light was turned off The middle or lower spray arm is blocked by dishware Solution Turn the dishwasher off using the O button Turn the interior light on see Additional options BrilliantLight Open the dishwasher door and rearrange items blocking the spray arms The spray arm jets of the middle or lower spray arm are clogged Turn the dishwash
54. ter frequent washing Cast iron pots and pans depending on model If unsure whether your china and crystal are dishwasher safe please check with the manufacturer The China amp Crystal program although extremely gentle and thorough can cause the china and crystal to wear if they are not dishwasher safe Glassware There are no standard guidelines for washing glassware when in doubt wash by hand When purchasing new dishes glasses and cutlery make sure they are dishwasher safe Only wash items marked dishwasher safe in the dishwasher If fine glassware is washed in the dishwasher select the China amp Crystal program This will reduce the risk of clouding Silver and aluminum Silver or aluminum items may tarnish Silverware previously cleaned with a silver polish may be damp or spotted at the end of a program where water has adhered to the polish This can be rubbed off with a soft dry cloth Silver that has been cleaned in an immersion dip is usually dry at the end of a program but may tarnish If left to dry foods containing sulfur can discolor silver These include egg yolk onions mayonnaise mustard fish and marinades Silverware may tarnish or pit if washed next to stainless steel Leave space between these metals Clean aluminum items e g grease filters with domestic dishwasher detergent only 21 Loading the dishwasher Typical load
55. tergent packaging If using a Tab detergent see Settings Deactivate indicators Detergent tabs are not recommended for use with the program Express depending on model The tabs may not dissolve completely Dishwasher cleaning products are available from Mlele Adding detergent m Add detergent to the compartments m Press the latch on the detergent O Close tne On amen NAP dispenser The flap will spring open Use one tab or add powder or gel detergent to compartment II and The flap is always open at the end of a close the flap program m l a Pre rinse is desired and available for your chosen program add 1 teaspoon 5 ml of detergent to compartment I Compartment holds a maximum of 2 teaspoons 10 ml compartment II holds a maximum of 3 5 tablespoons 50 ml of detergent The horizontal marks in compartment II indicate the levels of approximately 1 1 4 and 2 tablespoons 20 and 30 ml respectively The marks indicate the approximate fill level in ml when the door is open in a horizontal position 35 Use Turning on m Make sure the spray arms can rotate freely m Close the door m Open the water supply if closed m Turn the dishwasher on The main menu shows in the display If the memory function is selected the last selected program is displayed See Settings Memory hain menu 12 00 a Settings P a Sensor Wash Express nz C Selecting
56. tification will be shown See Frequently Asked Questions for more information If the water pressure is higher than shown a pressure reducing valve must be used Ensure that the water connection is secure after the first use To prevent damage to the dishwasher it must only be connected to a fully vented drainage system Do not cut the intake hose If the hose is cut the dishwasher will not work There will be a water leak If the hose is too long coil it neatly and place it behind or under the machine 81 Plumbing Drainage The machine comes equipped with a built in non return valve on the discharge side to prevent waste water from flowing back into the dishwasher The dishwasher is equipped with a 5 ft 1 5 m flexible drain hose with an internal diameter of 7 8 22 mm Drain hose extensions and adapters can be ordered from Miele The maximum drain hose length is 13 ft 4 m max drain height 39 1 m Use the clamp provided to attach the hose to the dishwashers P trap or disposal connection see the Installation Diagram The hose must always be attached on the sink side of the P trap When attaching the hose to a garbage disposal fitting make sure the plug which is normally blocking the fitting is knocked out or removed The hose can be angled to the left or right side at the rear of the machine The existing nipple that the drain hose is connected
57. to may be designed for various hose diameters If the nipple diameter is to large or to small it should be replaced or an adapter may be used If the nipple extends more than 2 50 mm into the drain hose it should be shortened or the hose could clog 82 The drain hose must not be shortened N Make sure the hose is not kinked or cut when pushing the machine under the countertop Venting the drainage system If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8 20 cm above the floor the drain must be vented Otherwise the water inside the dishwasher may siphon out during the wash program m Open the dishwasher door and remove the lower basket m Pull the lower spray arm firmly upwards to remove m Cut off the vent cap located at the right rear of the triple filter system as illustrated 83 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643
58. ur liquid rinse aid into the reservoir until it is visible on the surface of the screen The rinse aid reservoir holds approximately 3 7 fl oz 110 ml 18 Before using for the first time Rinse aid indicator appears the reservoir contains sufficient rinse aid for 2 3 programs only m Add rinse aid once the program has finished m Confirm with the OE button The Refill rinse aid message will go out If using Tab detergent products in your dishwasher the messages can be turned off if desired see Settings Refill display If you switch to using detergent that does not contain salt or rinse aid it is important to remember to replenish the salt and rinse aid and to turn the indicators back on Loading the dishwasher Do not wash items soiled with ash sand wax grease or paint in the dishwasher Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher Wax grease and paint will cause permanent discoloration and damage to the dishwasher Scrape food from dishes before placing them in the dishwasher rinsing is not necessary m Some foods contain natural dyes e g Carrots or tomatoes Plastic items may discolor permanently if they come in contact with food dyes m All items can be placed anywhere in the baskets m Load dishes so that water can reach all surfaces Do not place dishes or cutlery inside other pieces m Make sure that
59. wer basket m Push down on the insert to snap it into position 29 Loading the dishwasher Universal support bar The support bar will hold tall glasses and stem ware securely lik 7 A SEN K Oy M DE el k ion V m Fold the bar down and lean the desired glasses against it m f desired a section of the cutlery tray can be removed to allow for even taller glasses 30 Foldable spikes The rows of spikes can be lowered to make more room for larger items such as casserole dishes m Press the yellow lever down and fold down the spikes Vase Bottle insert The vase bottle insert can be used to rinse narrow items e g vases baby bottles etc m Pull the insert up and bend to the side if not needed Loading the dishwasher Cutlery JS AT GL i Split cutlery tray E depending on model Spoons with thick handles may have to be placed as knives and forks with their heads in the holders m Arrange the cutlery as shown in the cutlery tray For easier unloading cutlery should be grouped in zones one for knives one for forks one for spoons etc Spoon heads should be placed in IE contact with at least one of the serrated DM ret
Download Pdf Manuals
Related Search