Miele G 1262 User's Manual
Contents
1. Adjusting the upper basket Depending on the setting of the upper basket a variety of plate dimensions The upper basket can be raised or san be accommodated lowered to accommodate tall items For example If the upper basket is in its highest position a plate with a diameter of 12 4 31 cm can be fit in the lower basket The basket can also be angled to fit tall items in both the upper and lower baskets The angles should not be set to opposite extremes This will block the middle spray arm Take care when sliding the basket in and out in this position m Slide out the upper basket m Pull up the levers at the sides of the upper basket and adjust the basket height m Release the levers and the basket will lock in place 20 Loading the dishwasher Lower basket m For larger and heavier items such as plates serving platters Saucepans bowls etc Small plates and saucers can also be arranged in the lower basket Foldable spikes Both rows of spikes in the front section of the basket can be folded down to create more room for larger dishware e g pots pans and bowls m Press the yellow lever down and fold down the spikes 21 Loading the dishwasher Removeable PlateGuard Plus with SteamGu2. Detergent residue is blocking the catch properly This is not a fault It is the normal operating mode of the drying system Dry the dispenser before adding detergent Remove the residue The moisture will evaporate after a short time Before fixing the fault Turn the dishwasher off Q The triple filter in the wash cabinet is clogged Clean the triple filter See User Maintenance Instructions The drain pump or the non return valve may be blocked Clean the drain pump and the non return valve see User Maintenance Instructions The drain hose is kinked Remove any kinks from the drain hose 37 Frequently asked questions Sounds Problem There is a knocking noise in the wash There is a rattling noise in the wash cabinet There is a knocking noise in the water pipes Possible fault The spray arm is hitting an item in the basket Items are not secure in the wash cabinet This may be caused by the installation or the diameter of the pipe Solution Interrupt the program rearrange items blocking cabinet the spray arms Interrupt the program and rearrange loose pieces This has no effect on the dishwasher If in doubt contact a plumber 38 Frequently asked questions Poor cleaning results Problem The dishes are not clean Glasses and cutlery show streaks There is a bluish sheen on
3. Problem Possible fault Solution The program does not The door is not Close the door firmly start properly closed The machine is not Insert the plug plugged in The fuse is defective Reset the circuit breaker or the breaker has See data plate for minimum tripped amperage The dishwasher is X Turn the dishwasher on not turned on and select a program The dishwasher stops The fuse has Reset the circuit breaker during a program tripped See data plate for minimum amperage The optical indicator is not The reflector was Install the reflector properly visible when a program not properly see the separate Installation has started installed sheet 34 Frequently asked questions Problem The optical indicator flashes The buzzer sounds All program indicators are flashing fast when the door is open The time display shows FXX Possible fault There may be a technical fault Solution Turn the dishwasher off O After a few seconds Turn the dishwasher on Select the desired program with the program button Close the door If the problem persists contact Technical Service The drain pump is running when the door is opened Fault F70 The waterproof system has activated Turn off the water supply Contact Miele Technical Service 35 Frequently asked questions Problems water intake drain Problem Possi
4. The Salt indicator will not light if the dish washer had been programmed for a water hardness of below 4 d 4 gr gal US Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware The rinse aid is filled in the reservoir and the set amount will be automatically dosed N Filling the rinse aid reservoir with detergent will damage the reservoir Only pour rinse aid formulated for residential dishwashers into the reservoir When using Tab detergents rinse aid is not needed Adding rinse aid m Press the button in the direction of the arrow until the flap springs open 14 m Pour liquid rinse aid into the reservoir until it its visible on the surface of the screen The rinse aid reservoir holds approx 3 7 oz 110 ml m Press on the flap until you hear it click shut Failure to close it all the way allows water to enter the reservoir during the wash program m Clean any spilled rinse aid The flap will remain closed during normal operation Before using for the first time Rinse aid indicator When the rinse aid indicator first comes on there will be enough rinse aid left for 2 3 washes m The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling If the Tab function is selected the rinse aid indicator will not light see Additional options Tab Adjusting the dosage The dosa
5. of detergent to compartment I The horizontal marks in compartment indicate the levels of approximately 1 1 4 and 2 tablespoons 20 and 30 ml respectively Compartment holds a maximum of 2 teaspoons 10 ml Use Turning on m Open the water supply if it is closed m Open the door m Make sure the spray arms can rotate freely m Turn the dishwasher on The indicator and the indicator of the last set program lights up Selecting and starting a program Choose your program according to the type of load and soiling See the Program Guide for more information m Select the desired program with the Program button The program indicator of the selected program lights The time display shows the duration of the selected program in hours and minutes If the Turbo or Tab option is selected the respective indicator lights up m Select an additional function if desired see Additional functions for more information m Close the door The program starts The optical indicator lights as confirmation of a running program Cancel a program only in the first few minutes Otherwise important program steps e g the water softening may be interrupted 27 Program guide Program When to use Program sequence Pre rinse Interim rinse Main wash Final rinse Drying Pots amp Pans For normally soiled pots and pans with dried on food also for heav
6. Contracts please contact your appliance dealer or visit us online at http mieleusa com mielecare 43 Transport To transport the dishwasher e g when moving to a new home note the following Empty the dishwasher Secure any loose parts e g hoses cables cutlery baskets Transport the dishwasher in the upright position If unavoidable it may be transported on its back Do not transport it on its side or on the door Residual water in the machine could leak and cause electrical damage 44 User Maintenance Instructions To prevent accidents and appliance damage read these instructions before installation or use Cleaning and Care Check and clean your dishwasher regularly This will help avoid faults and problems A Abrasive cleaning agents all purpose cleaners thinner or ammonium cleaners should not be used on the dishwasher They will damage the surface Wash cabinet Generally the wash cabinet is self cleaning if the correct amount of detergent is used The wash cabinet can be cleaned with a dishwasher cleaner such as Dis Cleaner available from your Miele dealer Miele or online at www miele com Door and the door seal m Wipe the door seals regularly with a damp cloth to remove food deposits m Food residue and spilled liquids should be wiped from the sides of the dishwasher door These are outside of the wash cabinet and are not cleaned by wa
7. are dull and discolored film cannot be wiped off Tea or lipstick stains have not been completely There are rust stains on cutlery Glasses are not dishwasher safe The wash temperature of the selected program was too low There is no remedy Only wash dishwasher safe glasses in the dishwasher Select a program with a higher temperature The detergent has a low The affected items are not corrosion resistant Use a different detergent removed bleaching effect Plastics are Natural dyes e g from Use more detergent see discolored vegetables may be the cause Adding detergent Not enough detergent was used Discoloration is to break down natural dyes permanent There is no remedy Only wash dishwasher safe cutlery in the dishwasher A program was not run after refilling salt depending on model Salt residuals got into the wash cycle Start the Express program empty and without the Turbo function after refilling the salt The salt container lid was not screwed on properly depending on model Reseat and screw the lid on firmly 41 Comparison tests 10 place settings Standard program Normal O Q Q Q O Upper basket Lower basket Cutlery tray 42 After sales service Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of th
8. off with O Before using for the first time Filling the salt container A inadvertently filling the salt container with dishwashing detergent will damage the water softener N Only use water softener salt specially formulated for dishwashers Other salts may contain insoluble additives which can impair the water softener m Remove the lower basket and unscrew the salt container lid When opening the salt container water will run out Open the container only to refill salt Important The salt container must be filled with 1 quart 1 I of water before adding salt for the first time Water does not have to be added with subsequent refills m Place the provided funnel over the salt container Carefully fill with salt The salt container holds approx 3 3 Ibs 1 kg of salt As it is filled water will run out m Clean any excess salt from the threads of the container opening Screw the lid on firmly m f the dishwasher will not be used immediately run the Express program without the Turbo function This will remove any traces of salt from inside the wash cabinet Salt indicator m When the Salt indicator comes on refill the salt after the program has finished After the container has been filled the water softener is automatically reactivated the next time the dishwasher is started The Salt indicator will be lit during this process It will go out once the reactivation process is complete
9. rad 44 User Maintenance Instructions 45 Cleaning and Care 46 Triple filter SYSTEM sesse sioe sek RR ERR abat Pea E Race aee t 48 Cleaning the spray arms 50 Cleaning the water inlet i r iiie 51 Cleaning the drain pump and non return valve 52 Installation instructions 53 Help to protect the environment 54 Electrical connection 55 Plumbing rov REIR ENG ESTNE CR Gu ERE eb RP de 56 Waterproof Syster as a kasta vetet c ned x oa bead et e Eck ua edes 56 Connection to the water supply 56 DYEING Str RT AT desat tela 57 IMPORTANT SAFETY INSTRUCTIONS WARNING When using your dishwasher follow basic precautions including the following Read all instructions before installation or use of the dishwasher to prevent injury and machine damage Use the dishwasher only for its intended purpose This appliance is intended for residential use only Keep these operating instructions in a safe place and pass them on to any future user Electrical Safety P Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond
10. Qmiele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercareQmiele ca general and technical enquries Alteration rights reserved 1711 G1262 CE M Nr 07 768 790 02 INFORMATION IS SUBJECT TO CHANGE PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS TECHNICAL amp WARRANTY INFORMATION
11. aluminum items e g grease filters with domestic dishwasher detergent only Loading the dishwasher Cutlery tray d A SEC S 4 XS ES S osa amp Y X TE Cy f A CE d 2 UM Spoons with thick handles may have to be placed as knives and forks with their heads in the holders m Arrange the cutlery as shown in the cutlery tray For easier unloading cutlery should be grouped in zones one for knives one for forks one for spoons etc Place knives with the cutting edge down and forks with the prongs between the holders Spoons should be placed in the opposite direction with the handles between the holders so that water can run off more easily The upper spray arm must not be blocked by tall cutlery items The cutlery tray insert is removable 18 Loading the dishwasher Upper basket A Always use the dishwasher with the upper and lower basket in place m Load the upper basket with small lightweight or delicate items such as Cups saucers glasses dessert bowls and flat pans m Long items such as soup ladles mixing spoons and long knives should be placed lying down across the front of the upper basket Adjustable cup rack AN S N NS N y MA MDs LIN AN SSX e S m Raise the rack to make room for tall glasses Lower it to double stack smaller pieces U ES NO Loading the dishwasher
12. ard This insert is ideal for cups glasses plates bowls pots and pans Removing the insert m Press the insert downwards and at the same time press the catch inwards m To arrange tall items the cup rack Replacing the insert Can De Taeg m Place the insert back into the lower m The stemguard can be used to hold basket h f gl ff l Dae SE m Slide the hitches of the insert under the struts of the lower basket m Push down on the handle to snap the insert into position 22 Loading the dishwasher Vase Bottle insert depending on model The vase bottle insert can be used to rinse narrow items e g vases baby bottles etc m Place the insert into the lower basket as shown in the illustration If placed anywhere else water will not reach all surfaces The item will not be properly cleaned 23 Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele Depending on the model some accessories come standard with the machine Multi function basket GMFO To wash baby bottles saucers and small items attaches to the upper basket Cappuccinatore insert GCEO To wash the parts of the Cappuccinatore Large diameter plate insert GTLU 35 To wash plates with a diameter up to 14 85 cm attaches to the lower basket Tall glassw
13. are insert GGU To wash a large number of tall glasses attaches to the lower basket Glassware Insert GGO 24 To wash long stemmed glassware attaches to the upper basket Use Detergent Dishwasher detergents contain irritant and corrosive ingredients Avoid inhaling or swallowing dishwasher detergent Keep children away from detergent Fill the detergent dispenser only when you are ready to start the dishwasher N Only use detergents formulated for domestic dishwashers Use only the recommended amount of detergent Continued use of too much detergent may cause machine damage When using the China amp Crystal program depending on model reduce the amount of detergent used to at least of the normal dosage Also make certain your china and crystal are dishwasher safe You can use powder gel or tab detergents Follow the dosage information on the detergent packaging Detergent tabs are not recommended for use with the program Express The tabs may not dissolve completely Dishwasher cleaning products are available from Mlele 25 Use Adding detergent m To open press the latch on the detergent dispenser The flap will spring open The flap is always open at the end of a program 26 m Use one tab or add powder or gel detergent to compartment II and close the flap m f a Pre rinse is desired and available for your chosen program add 1 teaspoon 5 ml
14. asher to the mains when all installation and plumbing work is complete IMPORTANT SAFETY INSTRUCTIONS Use P To reduce the risk of injury do not allow children to play in on or near the dishwasher P Only use the dishwasher if all panels are properly in place P Do not tamper with the controls P Do not damage sit or stand on the door or baskets of the dishwasher Close the door when not in use P Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period turn on all hot water faucets and let water flow from each for several minutes before using the dishwasher This will release any accumulated hydrogen gas Do not smoke or use an open flame during this time P Be sure that all items placed in the dishwasher are dishwasher safe For items not labeled check the manufacturer s recommendations P When loading tableware place sharp items away from the door to prevent damage to the seal Load sharp items pointing downwards to prevent injuries P Only use detergents and rinse aids recommended for residential dishwashers Keep all detergents and rinse aids out of the reach of children P Do not inhale or swallow detergents Dishwasher detergents contain irritant and corrosive ingredients They can cause burning in the mouth and throat if swal
15. ble fault Solution The optical indicator The water supply Open the water supply flashes is shut off The buzzer sounds The Intake Drain indicator flashes when the door is open The dishwasher stops Before fixing the fault The optical indicator Turn the dishwasher off O flashes Fault F12 F13 Open the water supply The buzzer sounds The Intake Drain indicator flashes when the Water intake fault _ Clean the water intake filter see User Maintenance Instructions door is open The time display shows The water pressure at the FXX water connection is lower than 4 35 psi Consult a plumber Fault F11 Water See User Maintenance drain fault Instructions There may be Clean the triple filter water in the wash Clean the drain pump and the cabinet non return valve Remove any kinks in the drain hose 36 Frequently asked questions Problem General problems with the dishwasher Possible fault Solution The display turns off The dishwasher has gone into Standby mode to save energy Press any button The display turns on again Detergent is left in the dispenser at the end of a program The detergent lid cannot be closed The door and the interior walls are still wet after a program has finished Water remains in the wash cabinet at the end of a program The dispenser was damp when detergent was added
16. e your water hardness d gr gal The water hardness was programmed to 15 d 16 gr gal by factory default Before using for the first time Programming the water softener To exit the programming mode at any time turn the dishwasher off with the button m Turn the dishwasher off with O m Press and hold the Program and buttons simultaneously Hold the program button until the lower right program indicator lights If it does not come on start over m Press the Options button twice The Tab indicator flashes twice in intervals P 7 5 flashes in the time display A water hardness setting of 15 d is set factory default The set value is indicated in the time indicator following P see table 12 70 gr gal Setting in display 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 8 8 8 9 9 9 10 10 10 11 11 11 12 12 12 13 13 13 14 14 14 15 15 15 16 16 16 17 17 17 18 18 18 19 19 19 20 20 20 21 21 21 22 22 22 23 23 23 24 25 24 25 26 25 26 2r 26 27 28 27 28 29 28 29 30 29 30 31 30 31 32 31 32 33 32 33 34 33 34 35 34 35 36 35 36 37 36 37 45 38 46 45 46 60 47 62 60 61 70 63 73 70 m Press the Program button to select the value which corresponds with the water hardness in your area With each press of the button the value will raise Once the highest value is reached the values will start again from the beginning m Turn the dishwasher
17. eee Viele Operating Instructions ds i GER eee hia iia Dishwasher G 1262 To prevent accidents en US CA ce damage installation or use M Nr 07 768 790 Contents IMPORTANT SAFETY INSTRUCTIONS essel sess 4 Guide to the dishwasher 7 Caring for the environment 9 Before using for the first time 10 Te oper the AO sen ee ec Eee clo e dit rt dite citt 10 Te 6lose tlie dao see ria Rode hante dete eec net nd oe d 10 Water SOTTeRGr este dd ie dans die INR RER A MINE 11 Programming the water softener 0 cece 12 Filing the Salt container ius endowed nae sa Ras DAR See REOR XO n ie e 13 SAT INGICALON e e ai naar ie do dune dede vatur ne do Nador 13 FIRST AI A nd a tha en ae ge chee 14 Adding NSE AIG uua bee n po m mere ed ege ce o xac RR e arie 14 Rinse aid IridiGator 244224 bade EGS EAE Shade Vet VOTRE ea E ce 15 Adjusting the d0Sag s 1 4 La Shey eee ened ehh ede Quod ERR oe dub Pl 15 Loading the dishwasher 16 Items not recommended for dishwashing 17 Cutler aY eene renee En 18 Upper Dask6t iis dei eren A epig eia qoe od iese te 19 Adjusting the Upper basKet is sess ga ex Ree Ree dim Fx t ndn s 20 MOWED ASKS RE Seth tas stem cena toe cess eee pop cae aus Beattie etapa ese erates en ete 21 Basket access
18. elf cleaning N The machine must not be used without all the filters in place m Check and clean the filter system periodically for any trapped or foreign objects The level of soiling and time it takes before the filters need cleaning will vary depending on your household usage m Turn off the dishwasher before cleaning 48 m Turn the handle counterclockwise to release the triple filter system m Lift the filter combination out of the machine 2 Remove any solid particles and rinse under running water Scrub with a nylon brush if necessary Cleaning and Care To clean the inside of the filter the flap must be opened m Push the clips together and open the flap m Rinse under running water m Close the flap so that the clip engages m Return the filter so it lies flat in the base of the wash cabinet m Lock the filter by turning the handle clockwise NThe triple filter system must be inserted and locked into place Large particles could get in the circulation system and cause a blockage 49 Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets The spray arms should be inspected and cleaned every 4 6 months m Turn off the dishwasher before cleaning Removing the spray arms m Remove the cutlery tray if present m Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm m Pull t
19. ets m Load dishes so that water can reach all surfaces Do not place dishes or cutlery inside other pieces m Make sure that all items are securely positioned m Hollow items such as cups and glasses should be placed upside down in the baskets m o ensure good water coverage tall narrow and hollow items i e vases or champagne glasses should be placed in the center of the basket rather than in the corners m Concave based items such as mugs or bowls should be placed at an angle so that water does not pool 16 m The spray arms must not be blocked by items that are too tall or hang through the baskets Check clearance by manually rotating the spray arms m Place very small items in the cutlery tray or basket so they do not fall to the bottom of the wash cabinet m Food residue and spilled liquids should be cleaned from the sides of the dishwasher door These are outside of the wash cabinet and are not cleaned by water from the spray arms Loading the dishwasher Items not recommended for dishwashing Cutlery with wooden handles Wooden cutting boards Glued items such as old knives with handles glued together around the shank of the blade Handmade craft items antique metal trimmed or decorative glassware Plastic items that are not heat resistant Copper brass tin or aluminum Dishes with color painted over the glaze These dishes may fade over time Fine glass
20. f the Tab indicator is lit than the program sequence is adapted to suit detergents than contain rinse aid as well as other components where applicable The rinse aid dispenser and indicator light are deactivated Follow the instructions of the detergent manufacturer The cleaning and drying performance of normal detergents versus tabs varies greatly 31 Additional options Delay start The starting time of a program can be delayed The start time can be delayed from 30 minutes to 24 hours With a delay start time between 30 minutes and 9 hours 30 minutes the delay is set in 30 minute increments For 10 hours or more it is set in one hour increments When using the Delay Start function make sure that the detergent compartment is dry before adding detergent Wipe dry with a cloth if necessary Otherwise the detergent could stick together and not completely rinse out Gel detergent should not be used when selecting Delay Start the detergent could leak out of the compartment m Open the door m Turn the dishwasher on The indicator lights m Select the desired program with the Program button m Press the lt gt button The last set delay start time will show in the time display The indicator gt lights m Set the desired delay start time with the lt gt button If you press and hold the lt gt button the time with automatically count up to 24h To start again at 30 mi
21. ge selector is preset to 3 This dispenses approximately 3 ml of rinse aid per program It can be adjusted from O to 6 Use a higher setting if spots appear on dry glassware Use a lower setting if streaking appears on dishes or glasses m Turn the dishwasher off OC m Press and hold the program button and at the same time turn the dishwasher on with I Hold the program button until the lower right program indicator lights If it does not come on start over m Press the Options button 3 times The Tab indicator flashes 3 times The time display shows P 3 flashing A rinse aid amount of 3 ml is selected factory setting The set value is shown in the time display after P m Select the desired setting with the program button Every touch of the button adjusts the level The dosage is saved m Turn the dishwasher off O Loading the dishwasher AA Do not wash items soiled with ash sand wax grease or paint in the dishwasher Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher Wax grease and paint will cause permanent discoloration and damage to the dishwasher m Scrape food from dishes before placing them in the dishwasher rinsing is not necessary m Some foods contain natural dyes e g carrots or tomatoes Plastic items may discolor permanently if they come in contact with food dyes m All items can be placed anywhere in the bask
22. he cardboard box and packaging protect the appliance during shipping These materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation 54 Disposal of an old machine Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Ensure that the appliance presents no danger to children while being stored for disposal Before discarding an old appliance unplug it from the outlet cut off its power cord and remove any doors to prevent hazards Electrical connection A Installation repairs and other work by unqualified persons could be dangerous Check that the voltage frequency and fuse rating shown on the data plate match the household mains supply The power outlet must be accessible after installation Do not use an extension cord to connect the dishwasher to the mains Danger of overheating See data plate on the right side of the door A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current This appliance is equipped
23. he lower spray arm firmly upwards to remove m Lift up the middle spray arm 5 to engage the ratchet and unscrew the m Use a pointed object such as a spray arm toothpick to push food particles into the spray arm jets m Remove the lower basket m Rinse thoroughly under running water m Return the spray arms and check that they rotate freely 50 Cleaning and Care Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher s shut off valve If your water is hard or the pipes contain sediment this filter may clog and prevent enough water from entering the wash cabinet The plastic housing of the water connection contains electrical wiring Do not cut the intake hose or submerge it in liquid Installing an in line water filter If your water contains a large number of insoluble substances a filter between the water valve and the intake hose connection is recommended These filters can be purchased from Miele Cleaning the filter m Turn off the dishwasher and pull the plug m Turn off the water supply m Unscrew the intake hose m Carefully remove the rubber seal m Remove the filter using needle nose pliers and rinse it under running water m Reinsert the filter and seal Make sure they are seated correctly m Screw the intake hose back on the water valve checking that it is not cross threaded m Slowly turn on the water suppl
24. hows D Dishes tends to chip if removed still hot from the dishwasher Let the dishware cool After turning off the dishwasher open the door slightly The dishes will cool much faster m Unload the dishwasher Unloading the lower basket first will prevent water drops from the upper basket and cutlery tray depending on model from dropping onto dishes in the lower basket The optical function light goes out one hour after the end of a program m Turn the dishwasher off OC The dishwasher continues to use electricity until turned off with the O button 29 Use Preparing your appliance for an extended vacaion If you elect to turn off the water to your home for an extended period of time please note that this may not be enough to reduce the risk of a leak To be completely safe you must turn off the water supply to each individual appliance This means under the sink for a dishwasher at the laundry bib for your washer etc Interrupting a program A program is interrupted as soon as the door is opened If the door is closed the program will continue from where it was interrupted N Open the door with care The water in the dishwasher is hot Danger of scalding Before closing the door again leave it ajar for approx 20 secs This will enable the temperature in the wash cabinet to settle Close the door firmly until it clicks into place 30 Changing a program If the detergent flap is al
25. ily soiled dishware use 120 of normal detergent dose Normal For normally soiled dishware China amp Crystal For temperature sensitive glassware and lightly soiled dishware use 50 of normal detergent amount as required X as required SaniWash Extended wash time for sanitizing normally soiled dishware with dried on food Express Quick program for lightly soiled dishware e g party dishware Not suitable for detergent tabs Rinse amp Hold To rinse dishes when a complete program is not needed detergent is not recommended Usage Electric Water 28 0 01 1 23 kWh 1 3 5 3 gal 5 201 Use Time display Before the program starts the time display shows the running time of the selected program in hours and minutes During the running program the remaining time is shown in the time display The running time for the same program may vary depending on the intake water temperature load size and soiling When a program is selected for the first time a time is shown which equals an average program running time with cold water Each time a program is run the electronic adjusts the program running time according to the intake water temperature and the load size At the end of a program At the end of a program the optical function light flashes slowly with the door closed After opening the door the time display s
26. is booklet m Please quote the model type and number of your appliance These can be found on the data plate along the right edge of the door PC Update The Program Correction PC allows a technician to update the dishwasher to make use of new technology When for example technological developments offer advanced modifications to your existing program cycles a service technician will be able to input these into your machine controls via the indicator light marked PC Miele will provide information when such possibilities become available MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by Miele s Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service
27. lowed or inhibit breathing Consult a doctor immediately if detergent has been swallowed or inhaled D Do not drink water from the dishwasher Harmful residues could be present P Do not fill the rinse aid reservoir with detergent It will damage the rinse aid compartment P The door will close automatically once pushed against the door catch Do not put your hand inside of the door as it is closing Danger of injury D If the power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord Disposal of an appliance P If the appliance is removed from its installation site and will not be used remove the doorlock to the wash cabinet to prevent children from locking themselves in the machine SAVE THESE INSTRUCTIONS Guide to the dishwasher 00 Upper spray arm not visible Triple filter system 2 Cutlery tray Data plate 8 Upper basket Optical interface a Middle spray arm Rinse aid reservoir 8 Air inlet for drying Dual compartment detergent depending on model dispenser Lower spray arm Salt container Guide to the dishwasher Control panel Turbo Intake Drain 99 Aia Rnsead Sat FD o Pots amp Pans OO SaniWash program 100 Miele No
28. n longer see Use A Tab product was used These products have a low drying effect Set the Detergent setting for a normal detergent and add rinse aid The Tab option is turned on but a normal product Not enough rinse aid was used Set the Detergent setting to the detergent used see was used Additional options Tab Increase the dosage see Before using for the first time Unsuitable Tab products were used Change detergent use normal tabs or normal powder detergent The salt container is empty depending on model Refill the salt container see Before using for the first time The salt container lid was not correctly screwed on depending on model Reseat the lid making sure ir screws back on correctly 40 Frequently asked questions Problem Possible fault Solution Glasses are discolored and the film cannot Detergent deposits Use a different detergent and amount of detergent Any one or a combination of these faults may be to blame be wiped off Clouding or Possible causes may be See the relevant section of etching on excessive rinse aid incorrect this manual to glasses water hardness level set type adjust the rinse aid dosage adjust the water hardness level change the type and or adjust the amount of detergent used connect the dishwasher to a cold water supply Glasses
29. nt is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for an installation in these applications Please contact the nearest Miele dealer or the Miele Technical Service Department with specific requirements P It is recommended that the dishwasher only be connected to the mains with the plug no hard wiring The outlet must be accessible at all times after installation to disconnect the dishwasher D A WARNING Fire hazard Do not cover or crush the plug of the appliance Ensure that the cabinet opening for the dishwasher provides ample space for the plug Installing the dishwasher in a tight space may crimp the power cord or put pressure on the plug which could cause overheating P This dishwasher should only be installed under a continuous counter top secured to adjacent cabinetry P Do not install this dishwasher beneath a cooking surface oven or any appliance that radiates heat High temperatures from these units may damage the dishwasher P When installing the dishwasher under a counter top and removing the toekick a build under toekick must be installed Use the respective installation kit Danger of injuries P Do not cut the intake hose or submerge it in liquid This hose contains electrical components that could cause injury or property damage if cut or submerged P Only connect the dishw
30. nutes press the button twice m Close the door 32 The time will count down to the program start in 1 hour steps over 10 hours in 1 minute steps under 10 hours Once the delay start time has elapsed the selected program starts The display shows the remaining time the indicator lt gt goes out and the indicator of the selected program lights Delay start display Up to 59 minutes e g 30 minutes 20 Between 1 h and 9 h 30 min e g 5 hours 5 00 10 hours and over e g 15 h 15h Starting a program before the delay start has elapsed A program can be started before the delay start time has elapsed m Open the door m Press the O button m Press the button m Select the desired program with the Program button m Close the door The optical control lights The program begins Additional options Buzzer A signal sounds at the end of a program and when a fault occurs The buzzer at the end of a program sounds five times in quick succession for up to one hour The buzzer for a fault sounds in intervals up to two minutes The buzzer is activated by default It can be turned off so it does not sound at the end of a program The buzzer for a fault cannot be turned off m Open the door m Turn the dishwasher off with O m Press the Program button and at the same time turn the dishwasher on with m Hold the program button until the lower right program indicator come
31. ories 24 USC 25 Addingid t rgents sida b aod tte sheet DE e ena 26 TU ONE bat hed So RE K add Bae eee hae he he na 27 Selecting and starting a program 27 Program guide 28 gr MC 29 ire diSplay i2 ius bea baht ore tee teen eoim dede iit bai we aA 29 Atihie end ot a program sos reed pube b eR RS 29 Preparing your appliance for an extended vacaion 30 Interruptng a program s suce mura comic eee eR Do RR Erste ee er ane os 30 Changing a Program scum ete sobre ken Sahay ie satge pase bb ew Rd 30 Contents Additional options 31 MIO ORs RS me de D nm a eR eee 31 TA en a a M Pek at 31 Delay Start ns 32 rra is ET 33 Default SettinOS asses ar PENS Reha RR ne RPE dent dee ved and 33 Frequently asked questions 34 Technical Tale 6 s s der ten ead wee t ee aha Dar be head 34 Problems water intake drain 2 0 0 LL 36 General problems with the dishwasher 37 soU 253 oe nha oir ti es 38 Poor cleaning results em Oe tanned do als Be Ree RM ee dr 39 Comparison tests 42 After sales service 43 Transport ss ets RAR R shat eoe a a Ghee Sanka eed Rer
32. pened during operation the dishwasher will stop running Once the door is closed the program will continue 10 Before using for the first time Water softener Every dishwasher is tested before leaving the factory Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used To achieve good cleaning results the dishwasher needs soft water Hard water results in calcium deposits on dishware and in the dishwasher If your tap water hardness is above 4 d 4 gr gal US the water should be softened The water softener must be filled with dishwasher salt for reactivation If using Tab products which include salt you should still add salt to the machine to achieve optimal cleaning results Your local water authority will be able to advise you of the water hardness level in your area The dishwasher must be programmed to correspond to the water hardness in your area If the hardness of your local supply is constantly lower than 4 d 4 gr gal US you do not need to add water softener salt However the water hardness level must still be programmed In areas where the water hardness fluctuates example 37 50 d 39 52 gr gal always program the machine to the higher value in this example 50 d 52 gr gal If there is a fault it will help the service technician to know the hardness of your local water supply m Please not
33. rain pipe for the drain hose is designed for various hose diameters The drain pipe must be shortened if the drain pipe extends too far into the drain hose The drain hose could get clogged The drain hose must not be shortened N Make sure the hose is installed without kinking pressure or being pulled Venting the drainage system If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8 20 cm above the floor the drain must be vented Otherwise the water inside the dishwasher may siphon out during the wash program m Open the dishwasher door and remove the lower basket m Pull the lower spray arm firmly upwards to remove m Cut off the vent cap located at the right rear of the triple filter system as illustrated 57 58 59 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca professional
34. ready open do not change the program If a program has already started and you wish to change it m Open the door m Press the O button m Press the button m Select the desired program with the program button m Close the door The optical control lights The program starts Additional options Options With the Options button the functions Turbo and Tab can be selected m Open the door m Turn the dishwasher on T The indicator lights up m Press and hold the Options button until the indicator of the desired function lights up The option will remain active for all programs until the setting is changed again m program can now be started as usual or the dishwasher can be turned off O Turbo The Turbo function can be used to reduce the program run times in programs in which the option is available Using the Turbo option during the Express program will rinse the dishes without heat e g to avoid smells if a complete program is not yet needed Tab To achieve the best results the dishwasher can be programmed for the type of detergent being used The Options button can be used to select between normal detergents powder or gel and tabs The program sequence is adapted to the selected detergent type Depending on the program selected the run time may be extended considerably If the Tab indicator is not lit the dishwasher is set for normal detergent I
35. rm O Ex is Q formal ol press China amp Crystal OO Rinse 8 Hold gt 0O Time display 2 Delay Start button with indicator 8 Options button 4 Check Refill indicators Program selection 6 Program button On button Indicator Off button O 8 Optical Interface Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity For best results follow these tips m For lowest energy consumption you may connect the dishwasher to a cold water source m For fastest possible wash times with slightly higher energy consumption connect the dishwasher to a hot water source m Make full use of the baskets without overloading for the most economical washing m Use the correct amount of detergent and rinse aid Detergent dosage is dependent upon the amount of soiling and type of dishware being washed See the Program Guide for more information m When using powder or gel detergent reduce the amount to of the normal amount when washing a small load m Choose a program that best suits the degree of soiling and the type of dishes being washed m For small loads select Express Before using for the first time To open the door To close the door m Push the baskets in m Lift the door and push until it clicks into position m Pull the handle to open the door If the door is o
36. s on If it does not come on start over m Press the Options button four times The Tab indicator flashes four times in intervals The time display shows if the program end buzzer is turned on or off P l Buzzer is turned on P Buzzer is turned off m Press the Program button to change the setting The setting is saved m Turn the dishwasher off with O Default settings All settings can be reset to the factory default m Open the door m Turn the dishwasher off O m Press and hold the Program button and at the same time turn the dishwasher on Hold the Program button until the lower right program indicator comes on If it does not come on start over m Press the Options button 12 times The Tab indicator flashes once long and twice short in intervals The time display shows if a setting was changed P 7 All settings are factory default P 0 At least one setting was changed m To reset the dishwasher to the factory default press the Program button The setting is saved m Turn the dishwasher off O 33 Frequently asked questions With the aid of the following guide minor problems can be fixed without a service call Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage Technical faults
37. slightly higher energy consumption connect the dishwasher to a hot water source All programs use hot water in the rinse cycles The inlet hose is approximately 5 ft 1 5m long A 5ft 1 5m drain extension is available from Miele The water inlet hose comes equipped with a 3 4 female hose thread connector This can be directly connected to a water supply with 3 4 MHT male hose thread ends Water pressure Must be between 4 5 145 psi 0 3 10 bar 56 A To prevent damage to the dishwasher it must only be connected to a fully vented drainage system Do not cut the intake hose It contains electrical wiring If the hose is cut the dishwasher will not work There will be a water leak and you could be injured If the hose is too long coil it neatly and place it behind the machine Plumbing Drainage The machine comes equipped with a built in non return valve on the discharge side to prevent waste water from flowing back into the dishwasher The dishwasher is equipped with a 5 ft 1 5 m flexible drain hose with an internal diameter of 7 8 22 mm Drain hose extensions and adapters can be ordered from Miele The maximum drain hose length is 13 ft 4 m max drain height 39 1 m If the hose is to be directly fitted to the drainage outlet on site use the supplied hose clip see assembly plan The hose can be installed to the left or right side The existing d
38. ter from the spray arms 46 Exterior m Use a conditioner suitable for your kitchen cabinetry m Clean wood with a damp cloth and wipe dry Clean the exterior with a solution of warm water and liquid soap applied with a soft sponge Dry with a soft cloth Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly To better maintain your appliance avoid the following cleaners containing soda ammonia thinners or chlorides cleaners containing descaling agents or lime removers abrasive cleaners stainless steel cleaners dishwasher soap powder caustic oven cleaners scouring pads steel wool hard brushes metal scrapers Cleaning and Care Indicator reflector The reflector of the optical interface is located in the steam deflector beneath the counter top m Clean as necessary with a damp cloth Control panel m Clean the control panel as necessary with a damp cloth NThe appliance front and controls are not scratch proof Remove spills immediately 47 Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes It also protects the circulation pump from damage caused by foreign objects e g broken glass bones During normal use the filter system is s
39. the surface of glasses and film that can be wiped off Possible fault The dishes were not loaded correctly Solution See Loading the dishwasher The program was not powerful enough Select a more intensive program see Program Guide Not enough detergent was dispensed Use more detergent see Adding detergent The spray arms are blocked by items Turn the spray arm and rearrange the dishes if necessary The triple filter is clogged or not correctly inserted The spray arm jets may be clogged Clean the filter and insert the filter correctly see User Maintenance Instructions The drain pump or the non return valve is blocked Wash water will run back into the wash cabinet The rinse aid dosage is set too high Clean the drain pump and the non return valve see User Maintenance Instructions Reduce the dosage see Before using for the first time 39 Frequently asked questions Problem Dishes are not dry glasses and cutlery are spotted White residue is visible on cutlery and dishes Clouding occurs on glassware and film can be wiped off Possible fault too low or the rinse aid reservoir is empty Solution Increase the dosage refill The rinse aid setting may be the reservoir or switch the rinse aid product when refilling see Before using for the first time Dishes were taken out too soon Leave dishes i
40. to prevent injury and machine damage Consult a qualified electrician if in doubt P Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse P Do not use an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician IMPORTANT SAFETY INSTRUCTIONS Installation P The dishwasher must be installed and connected in compliance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty P Do not install or use a damaged dishwasher A damaged appliance is dangerous Unplug the machine and call your Miele dealer or the Miele Technical Service Department P Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation P This equipme
41. ware and crystal items should only be washed using the China amp Crystal program Otherwise clouding or etching may occur after frequent washing Cast iron pots and pans depending on model If unsure whether your china and crystal are dishwasher safe please check with the manufacturer The China amp Crystal program although extremely gentle and thorough can cause the china and crystal to wear if they are not dishwasher safe Glassware There are no standard guidelines for washing glassware when in doubt wash by hand When purchasing new dishes glasses and cutlery make sure they are dishwasher safe Only wash items marked dishwasher safe in the dishwasher If fine glassware is washed in the dishwasher select the China amp Crystal program This will reduce the risk of clouding Silver and aluminum Silver or aluminum items may tarnish Silverware previously cleaned with a silver polish may be damp or spotted at the end of a program where water has adhered to the polish This can be rubbed off with a soft dry cloth Silver that has been cleaned in an immersion dip is usually dry at the end of a program but may tarnish If left to dry foods containing sulfur can discolor silver These include egg yolk onions mayonnaise mustard fish and marinades Silverware may tarnish or pit if washed next to stainless steel Leave space between these metals Clean
42. with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances N Improper connection of the equipment grounding conductor can result in electric shock Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply please consult a licensed electrician or call Miele s Technical Service Department 1 800 999 1360 1 800 565 6435 Specifications The dishwasher comes equipped with a 4 ft 1 2 m power cord with a molded plug for connection to 120 V 60 Hz 15 A grounded receptacle 55 Plumbing Waterproof system All Miele dishwashers have a safety valve located on the incoming water line and a sealed underside with a water sensor If a fault occurs the water intake is stopped and the drain pump is activated Connection to the water supply AA Do not drink water from the dishwasher The dishwasher can heat its own water to the temperature required by the wash program This allows for connection of the machine to either a hot or cold water source For lowest energy consumption connect the dishwasher to a cold water source For fastest possible wash times with
43. y and test for leaks 51 Cleaning and Care Cleaning the drain pump and non return valve If the dishwasher is not completely drained at the end of a program the drain pump or non return valve may be blocked m Turn off the dishwasher and pull the plug m Remove the triple filter see Triple filter system m Use a cup or bowl to scoop water out of the wash cabinet m Tilt the locking clamp to the side m Pull out the non return valve 2 and rinse it under running water m Remove all foreign objects from the non return valve 52 The drain pump is beneath the non return valve see arrow m Remove all foreign objects from the drain pump glass or bone splinters m Before returning the non return valve check that the drain pump is not blocked Spin the propeller several times in both directions to check for obstructions m Carefully reinsert the non return valve and secure it with the locking clamp N Make sure the locking clamp clicks into place ser Installation Instructions Please refer to the Installation Diagram supplied with these instructions To comply with IEC sound testing protocols please contact Miele for additional instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information Help to protect the environment Disposal of the packing material T
Download Pdf Manuals
Related Search