Miele EGW4060-14 User's Manual
Contents
1. cords do not guarantee the required safety of the appliance This appliance must only be used once it has been properly installed into cabinetry to ensure that all electrical components are protected Never open the outer casing of the appliance Tampering with electrical connections or components and mechanical parts is dangerous and may cause machine damage IMPORTANT SAFETY INSTRUCTIONS Installation repair and maintenance work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty Hardwiring the appliance should be performed by a certified electrician in compliance with all local and national codes and requirements The manufacturer cannot be held responsible for the damages caused by an inadequate electrical connection Before installation or service disconnect the power supply to the work area by removing the fuse tripping the circuit breaker or unplugging the unit Pull the plug not the cord Use The plate warmer interior gets very hot when in use and remains hot for some time once turned off Use heat resistant pot holders when removing dishes Be sure that they are not damp or wet Danger of steam burns Pull the drawer out all the way when removing dishes to avoid touching hot drawer parts To prevent burns do not touch hot surfaces use handles or knobs Do not let children access the appliance or its c2. is turned off Turn the appliance on with the On Off button The wrong temperature was selected Check the temperature setting The vents were blocked by dishes Reload the dishes The dishes need more time to warm Allow the dishes to warm longer Why are the dishes are not warmed Possible fault Fix Check if a fan noise is heard If the fan is running the heating element has been damaged If the fan does not run the fan has been damaged The main fuse has blown Call Technical Service Call Technical Service Restore power Why are the dishes too hot Possible fault Fix The temperature control is faulty Call Technical Service Why does the On Off button not light when turned on Possible fault Fix The indicator light for the On Off button is bad Call Technical Service 12 After sales service In the event of a fault which you cannot correct yourself contact the Miele Technical Service Department 1 800 999 1360 techserv mieleusa com 1 800 565 6435 service miele ca When contacting Technical Service please quote the model and serial number of your appliance both of which are shown on the enclosed data plate Adhere the data plate to the box below Make sure the model given on the data plate matches that of this manual 14 Installation Instructions Help protect our environment D
3. repair work is being performed WARNING THIS APPLIANCE MUST BE GROUNDED 22 Note to the installer Please leave these instructions with the consumer Power supply This appliance is equipped with an approx 6 ft approx 1 8 m long power cord with plug ready for connection to a 120 V 15 A 60 Hz power supply 23 When contacting the Technical Service please quote the model and serial number of your appliance Miele Inc Miele Limited National Headquarters National Headquarters 9 Independence Way 55G East Beaver Creek Road Princeton NJ 08540 Richmond Hill ON L4B 1E5 Phone 800 843 7231 Phone 800 643 5381 609 419 9898 905 707 1171 Fax 609 419 4298 Fax 905 707 0177 www miele com www miele ca info miele ca general enquiries Technical Service amp Support professional miele ca commercial Nationwide enquiries Phone 800 999 1360 Fax 888 586 8056 Mielecare National Service Phone 800 565 6435 905 850 7456 Fax 905 850 6651 service miele ca Tech Service All rights reserved 1206 M Nr 06 543 300 01 en US
4. Miele Operating instructions gt i E Built in Plate Warmer EGW 4060 14 To prevent accidents and machine damage read these instructions before installation or use M Nr 06 543 300 Contents IMPORTANT SAFETY INSTRUCTIONS a 4 Guide to the machine 6 Before using the plate warmer 7 US 2 ee sg Waa eee nee ih sa th cus asta th ah eau eter ci ae aca Skee aS 8 CONMOIS 6 0 Che pee HHA ee RESP EE See saa paspa I 8 Operating sai rai adele Bb Tangga bak ia paf Qabuop mua Bed Bo 9 Selecting a temperature aa ka eee 9 Warming IMSS aan aka se ap 2 ded Sa he dh he kaa Ea dade Ocho AG Sead Reh deh BG et 10 CAPACI ces sai Bat achat danas Rage Be ed Beet Ae ene pena 10 Cleaning and care 11 Cleaning the plate warmer i 11 Non slip MET lt ska Aa 279 O Cae ae i 11 Frequently asked questions eee 12 After sales service Luua auaa 13 Installation instructions 15 Help protect our environment uaaa aaa 16 Installation eee 17 Installation Safety Instructions 0 eee 17 Built in measurement 17 Combinations EGW A0OX0 TA 20004 2098 Bead GR eae beta Pie hes 18 Installing ie Ap plane nae aussagen 20 Aligning the appliance Tont ananena 21 Electrical connection LL 22 IMPORTANT SAFETY INSTRUCTIONS This appliance is intended for residential use only Only use t
5. ation appliance can be set without a base directly onto the plate warmer A shelf between the appliances is not necessary To install the combination appliance please see the manual supplied with that machine This appliance is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for an installation in these applications Please contact the Miele Technical Service Department with specific requirements Built in measurement The appliance is available in two heights The opening measurement needed is the summary of the measurement of the plate warmer and the combination appliance Installation Combinations EGW 40x0 14 Oven H 4120 H 4220 Microwave compact oven 28 7 8 29 734 736mm 18 Installation CVA Steam ovens ES 91 Z BIC EC 19 Installation Installing the appliance m Set the plate warmer into the niche push it all the way in and align it at a right angle m Open the drawer and fix the appliance with the two supplied screws at the side panels of the cabinet 20 The installation kit contains 3 metal strips with adhesive on the back side Fix the metal strips on the plate warmer so that the gap between the appliance and the cabinet is sealed This air cushion acts as insulation m Remove the protective foil from the adhesive o
6. he appliance for its intended purpose Improper use of the appliance can lead to personal injury and material damage The manufacturer cannot be held responsible for damages caused by improper use of the plate warmer This appliance complies with current safety requirements Read all instructions before installing or using for the first time Keep these operating instructions in a safe place and pass them on to any future user Read all operating and installation instructions for any other appliance installed in combination with the plate warmer READ ALL INSTRUCTIONS Installation Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond in order to prevent injury and machine damage If in doubt consult a qualified technician The electrical safety of this appliance can only be guaranteed when continuity exists between the appliance and an effective grounding system The grounding system must comply with local and national safety regulations It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician The manufacturer cannot be held responsible for the damages caused by an inadequate grounding system e g electric shock Do not connect the appliance to the electrical supply with an extension cord Extension
7. isposal of the packing material The transport and protective packing materials are environmentally safe for disposal and may be recycled Ensure that any plastic wrap is disposed of safely and kept out of the reach of children Danger of suffocation Please recycle 16 Disposal of an old appliance Old appliances contain materials which can be recycled Please contact your local recycling center about potential recycling Ensure that the appliance presents no danger to children while being stored for disposal Installation Installation Safety Instructions Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond in order to avoid risk of damage to the appliance If in doubt consult a qualified technician The electrical outlet should be easily accessible after installing the unit Only install the plate warmer in combination with built in appliances recommended by the manufacturer When installed with other appliances the warranty is void since the manufacturer cannot guarantee the safe use of the plate warmer To install the plate warmer in combination with another appliance a built in shelf must exist in the cabinet to support the weight of both appliances When installed in combination with another appliance the plate warmer must always be installed beneath the other appliance The combin
8. n the metal strip m Align and fix the metal strips according to the illustration flush with the sides and the rear of the plate warmer m Install the combination appliance according to the manual supplied with that machine Installation Aligning the appliance front After installing the combination appliance it might be necessary to align the appliance front and or to even the gap between the plate warmer and the combination machine Flat washers are supplied beneath the knurled nuts which fix the drawer to the telescopic runners m Loosen the knurled nuts and take the drawer out m Align and even the gap with the flat washers by changing their position above or below the drawer on both sides 21 Installation Electrical connection The electrical installation instructions for any appliance installed in combination with the plate warmer must be observed When another appliance is installed in combination with the plate warmer to the same circuit breaker operating both appliances at the same time may cause an overload If in doubt consult a qualified electrician All electrical work should be done by a qualified technician in strict accordance with national and local safety regulations Installation repairs and other work by unqualified persons could be dangerous and may void the warranty Make sure power is not supplied to the appliance while installation or
9. ontrols Supervise its use by the elderly or infirm Do not use the plate warmer to reheat cook or keep food and drinks warm The condensation from food or drinks could lead to moisture damage in the appliance Do not lean or sit on the warming drawer This will damage the drawer The drawer can hold a maximum of 55 Ibs 25 kg Do not store anything in the warming drawer Forgotten items could melt or catch fire when the appliance is turned on Flammable liquids and materials should never be stored in above or under the plate warmer Do not use the plate warmer to heat the room Due to the high temperatures radiated objects left near the appliance could be damaged Do not use a steam cleaner to clean this appliance Steam could penetrate electrical components and cause a short circuit Pressurized steam may cause permanent damage to the surface and to components of the appliance for which the manufacturer cannot accept responsibility To prevent injuries do not use accessories not recommended by Miele Do not install outdoors Guide to the machine de TT i On Off button Temperature selector 3 Warming drawer Non slip mat Indicator Before using the plate warmer m Clean the plate warmer with a damp cloth and wipe dry m Heat the empty plate warmer for a minimum of 2 hours Turn the temperature selector to Maximum see Selecting a tempe
10. rature m Vent the room when heating the drawer for the first time Metal components have a protective coating which may give off a slight odor the first time your new appliance is heated The smell will dissipate after a short time and does not indicate a faulty connection Use The plate warmer is only intended for warming dishes Do not use the plate warmer to reheat cook or keep food and drinks warm Condensation from food and drinks may cause moisture damage to the appliance Use pot holders when removing dishes The drawer can hold a maximum of 55 Ibs 25 kg The appliance works with a convection system A fan distributes the heat evenly throughout the drawer The air circulation heats the dishes fast and evenly A protective grill prevents contact with the heating element and fan The floor of the warming drawer has a non slip mat to prevent plates and dishes from sliding when the drawer is opened and closed Controls The controls consist of the temperature selector and the On Off button They are only visible when the drawer is open The indicator on the front of the drawer show if the plate warmer is turned on or off Use Operating m Place the dishes in the drawer m Select a temperature m Turn the appliance on 1 The button will light m Close the drawer The drawer may open again if closed too forcefully m Turn the appliance off amp before removing
11. s an example Place settings for 6 people 6 plates diam 11 28 cm 6 soup cups diam 4 10 cm 1bowl diam 8 _ 22 cm 1 bowl diam 7 19 cm 1bowl diam 6 1 1 17 cm 2 serving plates 14 3 46 36 cm not pictured 80 Espresso cups or 40 Cappuccino cups Cleaning and care Cleaning the plate warmer Non slip mat The mat can be removed to clean the Let the drawer cool before cleaning Bottom dithe draver Never use abrasive cleaners m Clean the mat by hand with warm scouring pads steel wool or caustic water and liquid dish soap oven cleaners on the plate warmer They will damage the surface m Dry thoroughly Do not return the mat until it is completely dry The exterior of the plate warmer can be cleaned with warm water and liquid dish soap applied with a soft sponge Wipe dry using a soft cloth Stainless steel Stainless steel surfaces can be cleaned using a non abrasive stainless steel cleaner To help prevent resoiling a conditioner for stainless steel can also be used Apply sparingly with even pressure Frequently asked questions Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations Unauthorized repairs could cause injury or machine damage The manufacturer cannot be held responsible for unauthorized work Why are the dishes not warm enough Possible fault Fix The appliance
12. the warmed dishes Selecting a temperature The temperature selector allows you to select a temperature between 86 and 176 F 80 and 80 C Do not turn the knob counterclockwise or clockwise past the 9 o clock position Forcing it beyond these positions will damage the temperature selector When the selected temperature is reached the heating element turns off If the temperature falls below the selected one the heating element will turn on again The temperature scale shows symbols for the optimum temperature of the respective dish group D approx 105 F 40 C For cups or glasses approx 140 F 60 C For serving or eating plates When served in a prewarmed cup glass or plate the drink or food will not cool as fast and the cup or plate will remain cool enough to touch Use Warming times Various factors will affect the warming times type and thickness of dishes quantity how dishes are arranged and the temperature setting As you use the plate warmer you will learn which settings suit your needs best However the following information can be used as a guide At a temperature setting of about 140 F 60 C place settings for 6 people will be evenly warmed in approximately 30 to 35 minutes 10 Capacity The capacity of the appliance depends on the dish sizes The maximum load is 55 Ibs 25 kg The following assembly picture i
Download Pdf Manuals
Related Search