Miele Dishwasher M.-NR. 04 390 922 User's Manual
Contents
1. If the panel contacts the toekick while the dishwasher door is being opened the dishwasher toekick must be cut shorter or recessed deeper If H is equal to or less than the toekick height of the adjoining cabinetry no in terference will exist provided that R is at least 3 4 Note If a decorative or flush mount toe kick is desired and R is less than 3 4 other modifications such as beve ling the top rear edge of the toekick may be adequate 51 Dishwasher installation For kitchens utilizing a non continuous toekick The included toekick will fit without modification when The machine is set to its maximum height legs fully extended and the toekick Is recessed as far as possible 4 If the machine height is less than maxi mum or if the toekick is recessed less than 4 the toekick must be shortened see following page After installation carefully open the dishwasher door to check that the front panel does not hit the toekick If it does remove the toekick and trim it accordingly 52 Adjusting the toekick recess m lo adjust the depth recess of the toekick release the tension on the spring clips as shown and push the mounting brackets in as far as possible Trimming the toeckick The rear of the toekick has two cutting lines m Screw the toekick onto the installed brackets with the cutting lines to wards the top and pull out evenly until it aligns wi2. L t 12 13 14 15 16 17 18 19 20 oN Guide to the appliance Upper spray arm not visible Cutlery tray Inlet funnel for middle spray arm Upper basket Water hardness selector Middle spray arm Lower spray arm Four height adjustable levelling legs Combination filter Salt reservoir Dual compartment detergent dispenser Rinse aid reservoir with dosage selector Data plate On Off button Door release Child safety lock Time display Pushbutton switches Check indicator lamps Program sequence display Program and temperature selector knob Note Lower basket is not shown IMPORTANT SAFETY INSTRUCTIONS WARNING When using your dish washer follow all basic safety precautions This appliance conforms to all uniform safety codes and regulations To avoid injur and machine damage rea the operating instructions carefully The manufacturer cannot be held responsible for damage or injury caused by improper use or for uses other than those for which the appliance is intended Repairs should only be carried out by qualified personnel Disconnect the appliance from the power supply before servicing pull out the plug or turn off the circuit breaker If not purchased specifically as a Freestanding model only install the dishwasher under a continuous countertop which is secured to ad jacent cabinetry The dishwasher must be electri
3. twice for a 1 hour delay 1 00 is displayed 1 hr OOmin To prevent the detergent form pre maturely dissolving when using the Delay Start feature make certain that the dispenser is dry before put ting in detergent Top Solo 18 When this feature is selected the ma jority of the water is directed to the top and middle spray arms of the dish washer Its use is recommended when all the dishes or cutlery needing clean ing can be loaded into the upper bas ket and cutlery tray Note Lightly soiled plates or serving platters can still be placed in the bottom basket if large spaces are left between them Do not place dishes bowls or other hol low containers in the bottom basket Adjusting the upper basket to its lowest position will allow it to accommodate larger plates Using Top Solo will also save water detergent and energy For example using Top Solo with the NORMAL 55 C 130 F program uses 3 2 gallons 12 liters of water instead of the usual 5 gallons 19 liters Because smaller amounts of dishware are being washed the amount of deter gent used can be reduced accordingly Additional features Top Solo can be selected with all wash programs m Choose a program The length of the program will appear in the time display 17 in hours and minutes m Press the Top Solo button 18 The Top Solo indicator lamp illuminates and the program duration changes m
4. gent to use Not enough or too much detergent can lead to poor wash re sults Cleaning results vary from brand to brand If you are not satisfied with the results from one brand try another quality brand before contacting the Miele Service Department for advice Load the dishes correctly Load the dishes so that water can con tact all surfaces Ensure that the spray arms are not blocked by items which are too tall for the basket or which ex tend through the bottom of the basket If necessary manually rotate the spray arms to test for clearance The combination filter in the base of the wash cabinet and the spray arms must be kept clean These should be regularly inspected and cleaned if necessary see the corresponding chapters for de tailed information on the above points Opening and closing the door To open the door Wy m Press the release catch inside the door grip If the door is opened during operation all functions are automatically inter rupted To close the door m Push the baskets in m Lift the door and push until it clicks into position Child safety lock The child safety lock is designed to deter children from opening the dish washer door m Use the key provided to turn the child safety lock to the required set ting Horizontal setting The door is locked Vertical setting the door can be opened The water softener must be set to corre spond to
5. cally grounded Install the dish washer as per the included Installation instructions Use only detergents and rinse aids recommended for dishwashers Do not use commercial or indus trial grade detergents as these may cause adverse chemical reactions and damage the machine Use deter gents made for residential dishwashers only Do not use your dishwasher unless all enclosure panels are properly in place Do not allow children to play in or on the dishwasher Keep all detergents and rinse aids out of the reach of children Dishwasher detergents contain So dium Silicate and Sodium Carbo nate In case of eye contact immediate ly flush with water Call a physician or poison control Do not tamper with the controls IMPORTANT SAFETY INSTRUCTIONS When loading items to be washed Locate pointed items so that they are not likely to damage the door seal Load knives with the cutting edge down to reduce the risk of injuries Do not wash plastic items unless they are labeled dishwasher safe or the equivalent For items not labeled check the manufacturer s recommenda tions Do not abuse sit or stand on the door or dishracks of the dish washer Remove the front door and cut off the power cord of the dishwasher before removing it from service or dis carding it This will help protect child ren from injury and accidentally locking themselves in Under certain conditions hy drog
6. Press the START button 18 The START indicator lamp goes out and the program starts 31 Unloading the dishwasher 32 Dishes tend to break and chip easier when they are hot Allow the dishes to cool until they are comfortable enough to handle before unloading them If the door is opened at the comple tion of the drying cycle the dishes will cool much faster Unload the lower basket first then the upper basket and cutlery tray if so equipped This will prevent water drops from the upper basket or cut lery tray from falling onto the dishes in the lower basket Cleaning and care Cleaning the filters in the wash cabinet The combination filter in the base of the wash cabinet should be regu larly inspected and cleaned as necessary Any broken glass or dishware should be removed imme diately upon discovery Use caution when cleaning the fil ters non return valve or drain oump as glass or bone splinters may be caught in the bottom of the wash cabinet m urn the handle counterclockwise to release the filters m Lift the combination filter out of the machine Remove any coarse par ticles and rinse it under running water A nylon brush can be used if necessary 33 Cleaning and care m Turn the combination filter over and m Replace the combination filter so open the coarse filter cover by pull that it lies flat in the base of the wash ing back on the locking tab cabinet Secure
7. Range of adjustment is approximately 2 5 cm Dishwasher installation 1 Install the steam deflector if applicable A stainless steel plate is supplied to protect the underside of the countertop against steam rising from the dish washer when the door is opened If the countertop is made of Corian gra nite marble or other solid waterproof material the steam deflector should not be used m Squeeze a bead of sealant from the supplied tube into the angle formed by the curved edge of the cover plate m Align the plate with the lower front edge of the countertop see illustra tion and use the supplied tacks to nail it into place On countertops with wood or lami nate edging the tacks should be nailed through the rear holes of the plate 43 Dishwasher installation 2 Install the dishwasher under the countertop It is preferable to install the main water and electric supplies so that they can be accessed through an adjacent cabinet rather than situating them be hind the machine See the Plumbing and Electrical sections for proper con nection procedures before continuing m Place the slides with the ratchet at the rear onto the dishwasher legs m Unscrew the legs to raise the ma chine to within 1 4 5 mm of the underside of the countertop and check that the machine is level before sliding it into its opening Certain steps in the installation proce dures requir
8. and 1 1 4 ounces 20 25 and 30 ml respectively The wash program chosen should de pend on the type of dishes and the de gree of soiling In most cases a NORMAL program will give excellent results The available programs and some of their applications are listed in the Pro gram Chart on the next two pages Choosing a program ENERGY SAVER Program m Use this program for lightly to nor mally soiled dishware A warm water intake temperature of the incoming water of at least 45 C 115 F is necessary for this program Water is not heated in this program Only 0 20 kWh of electricity approx is used during this cycle The drying result may not match that of a program with a full drying cycle The higher the temperature of the in take water the better the drying results m Open the door of the dishwasher 2 3 inches 5 6 mm at the end of the program to speed the drying pro cess 25 Program chart Program When to use Detergent A B Compart Compart Compart ment ment ment lI II Pre wash Main Main wash wash Universal Programs NORMAL This program is for normal everyday loads 20 80 100 Do CNB Er NORMAL same as NORMAL 55 C 130 F but at a 20 80 100 65 C 150 F higher temperature for stubborn dried on particles INTENSIVE same as NORMAL 55 C 130 F but with a 20 80 100
9. case the reservoir should not be filled with salt The indica tor lamp will remain lit and should be disregarded or bypassed The Salt indicator lamp has also been designed for future program updates PC See the After Sales Service sec tion for further details Water softener Bypassing the Salt indicator lamp In order to bypass the salt indicator lamp you will need a screwdriver and needle nose pliers m Remove the salt reservoir cap Looking into the salt reservoir you will see the top of the float chamber on the right hand side m Using a screwdriver carefully pivot the float chamber towards the center of the reservoir m Using the needle nose pliers first pull the cap off of the float cham ber then remove the float m Replace the float chamber cap push the chamber back into its up right position and replace the salt reservoir cap The indicator lamp should now remain off Adding rinse aid The use of Rinse Aid is recommended Adding rinse aid to prevent spotting on dishes and glass ware that normally occurs during the drying phase of automatic dishwashing CHECK O Sprayarm O Water Intake Inadvertently filling the rinse aid reservoir with detergent always leads to damage to the reservoir Only pour rinse aid formulated for O Drain residential dishwashers into the Salt reservoir l O Rinse aid m Add Rinse Aid before the first use and anytime the Rinse Ai
10. convert an i dishwasher to a U version the spacer bars must first be removed and stored for possible use in the future See the separate in structions for installing the GDU decor set If the GDU kit is not being used skip the following step m lo remove the spacer bars from the control panel place the panel on a table printed side up and gently push down on the spacer bars at a 46 point near the bottom of the control panel This will release the mounting bolts from their slots Install the necessary spacer bars on the control panel Place the seal onto the ventilation grill Push the ventilation grill into the metal backing plate Place the covers over the push button switches Install the adapter disc Position the control panel over the backing plate and fasten it from the inside of the door using the six screws provided Align and press the program knob onto its shaft Dishwasher installation 4 Aligning the control panel with the drawer fronts m he control panel can be aligned with the drawer fronts of the kitchen cabinets by adjusting the spacer bars m Using an 8 mm socket turn the nut clockwise or counterclockwise until the spacers reach the required height m f necessary individual or all spacer bars can be removed Adjustment range from 4 1 2 112 mm control panel without spacer bars to 5 3 4 145 mm control pan
11. discharge side of the dishwasher the following requirements must be met No part of the drain hose should be higher than 39 1 mm If installed horizontally the drain hose can be up to 12 ft 3 5 m long If the drain hose is angled upwards in any way it cannot be longer than 5 ft 1 5 m The drain connection should be made as close as possible to the dishwasher The internal diameter 7 8 or 22 mm of the drain hose should not be re duced at any point 59 Technical Data Height Width Width of opening Depth Depth with door open Voltage Rated load Fuse rating Water pressure Hot water connection Drain height Drain length Power cord length 60 33 1 8 84 cm adjustable to 35 89 cm 23 1 2 59 8 cm 23 5 8 60 cm 22 1 2 57 cm U andi models 47 1 2 120 5 cm U and models 110 120 V AC 12 5 A 1500 W 15A 4 5 145 psi 0 3 10 bar 120 F 49 C max 140 F 60 C 3 ft 1 m maximum 12 ft 3 5 m maximum approx 5 ft 1 5 m 61 62 63 Miele Miele Appliances Inc Miele Limited National Headquarters 55G East Beaver Creek Road 22D Worlds Fair Drive Richmond Hill Somerset NJ 08873 Ontario L4B 1E5 Phone 908 560 0899 Phone Number 905 707 1171 Fax 908 560 9649 Fax Number 905 707 0177 Internet htto www miele de Southeast Regional Headquarters Pu 6400 Congress Avenue Suite 1700 Boca Raton FL 33487 Phone 561 995 8030 Fax 561 995 8083
12. it by turning the m After cleaning make sure that the handle clockwise coarse filter cover is properly locked in place 34 Cleaning the spray arms On rare occasions particles of food may get stuck in the spray arm jets They can be easily cleaned as follows Remove the lower basket and the cutlery tray if so equipped The cut lery tray frame can be pushed back In Unscrew and remove the upper spray arm J Lad m o remove the middle spray arm lo cated beneath the upper basket gently push upwards until it engages in the ratchet then unscrew it Cleaning and care m Lift up on the lower spray arm to remove it m o clean the spray arms use a pointed object to push the the food particles into the jets m Rinse under running water to com plete the process m After cleaning replace the spray arms Important After replacing the spray arms check that they rotate freely 35 Cleaning and care Cleaning the drain pump and non re turn valve Use caution when cleaning the fil ters non return valve or drain oump as glass or bone splinters may be caught in the bottom of the wash cabinet If the water in the dishwasher is not completely drained at the end of a pro gram the drain pump or non return valve may be blocked To clean them m Remove the combination filter m ilt the locking clamp to the side and pull out the non return valve 36 m Rinse the
13. nected directly to the drain line 58 Drain connection D 24 60 cm nominal Connect the supplied drain hose to the drain pipe of the kitchen sink either A above the trap using the clamp pro vided or B to the dishwasher connector of the garbage disposal When connecting the drain hose to the garbage disposal make sure to remove the knockout from the con nection nipple See disposal manu facturers instructions for this proce dure A sample of a correct water and drain installation of a dishwasher is shown A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher If your sink has one it is recom mended that the hose be discon nected and the hole plugged Venting the drainage system Only if the dishwasher drain hose is connected to a floor drain or toa drain pipe that is below the level of the lower baskets wheels the drain must be vented otherwise the water in side of the dishwasher may siphon out during the course of a wash program Vent the drain m Open the dishwasher door m Cut off the vent cap located at the right rear of the dishwasher behind the filters as illustrated Plumbing Additional note since all Miele dishwashers are equipped with an odor trap and non re turn valve the drain hose can be con nected directly to the drain pipe as illus trated If plumbing codes require an external air gap on the
14. non return valve under run ning water The drain pump is situated under the non return valve see arrow m Before replacing the non return valve check to make sure that noth ing is obstructing the drain pump m Carefully replace the non return valve and secure it with the locking clamp m Replace and secure the combination filter Cleaning the water inlet filter The water valve housing on the inlet hose contains electrical compo nents and should not be immersed or run through water A filter is incorporated in the inlet hose that is attached to the dishwasher s main shutoff valve If your water supply is hard or the pipes contain sediment this filter may clog and prevent suffi cient water from entering the wash cabinet It can be cleaned as follows Cleaning and care Cleaning the filter Disconnect the dishwasher from the electrical supply unplug it or shut off the circuit breaker m Turn off the main shutoff valve and unscrew the Inlet hose m Carefully remove the rubber seal m Remove the filter using needle nose pliers and clean It by rinsing under running water m Replace the filter and seal Make sure they are seated correctly m Screw the inlet hose back onto the water valve making certain it is not cross threaded m Slowly turn on the valve and test for leaks 3 Cleaning and care Installing an in line water filter If your water supply contains a large numbe
15. remains in the dishwasher at the end of a program The drain hose is kinked or clogged The drain pump or non return valve may be blocked see Cleaning and care 40 The Water Intake indicator lights during the ENERGY SAVER pro gram The ENERGY SAVER program re quires a water supply temperature of at least 45 C 115 F If the incoming water is less than this temperature the Water Intake lamp illuminates see also Program selection If your hot water system has been used recently not enough hot water may have been available to adequately clean the dishes m f necessary repeat the program If the Water Intake lamp lights again select a different program m Should you still have difficulties please contact your Miele Dealer or the Miele Service Department See back cover for addresses Please have the model number of your appliance available This information can be found on the data plate on the upper edge of the door After sales service Program update function PC The Salt indicator lamp has a second function It allows a technician with the proper equipment to access the pro gramming of the dishwasher to take ad vantage of the latest technological de velopments CHECK O Sprayarm O Water Intake O Drain Dox Salt ORinse aid For instance if a detergent that gives good wash results using only cold water becomes avail
16. the dishwasher Adjustable cup racks Coffee bar SS J WAS i 5 GAE IAN IZAAN B Le ZAU IN To make room for tall glasses raise the Place coffee mugs on top of the bar so rack upwards Lower it to double stack that they sit at a slant This allows all smaller items water to run off the base of the mug The bar can also be used as a separ ator between two rows of glasses keep ing them from leaning against each other This protects the glasses and en sures good wash results For wide items flip the bar over to the right aay 7 21 Loading the dishwasher Depending on the setting of the upper basket the following dishware dimen sions can be accommodated Adjusting the upper basket depending on model The upper basket height is adjustable If tall items of dishware are being Upper Upper Lower washed more room can be obtained basket basket basket by raising or lowering the upper basket position diameter diameter Top 3 12 20 5 cm 30 cm Middle 9 11 22 5 cm 28 cm Bottom 10 10 24 5 cm 26 cm the two locknuts on either side of the basket m Adjust the basket up or down to the desired height m lighten the locknuts The upper basket can also be set on an angle if required Do not set the angle to the extreme one side at the highest setting and one side at the lowest as this will impede the function of the middle spray arm 22 Items not
17. the water hardness in your area This can be obtained from your local water company or by using a test kit that can be purchased from the Miele Parts Department To avoid the build up of calcium de posits on dishes cutlery and in the dishwasher if the water hardness is above 4 gr gal the water should be softened The dishwasher is factory set for a hard ness level of 22 gr gal If your water is harder or softer the setting will need to be adjusted To ensure a steady supply of soft ened water the built in water sof tener must be 1 Correctly set 2 Reactivated with salt wnen depleted Where the water hardness fluctuates e g 8 17 gr gal always set the ma chine to the higher value 17 gr gal in this example Water softener Settings value water gr gal ppm a for level orogram selector ming Setting 1 20 2 1 6 2 40 4 2 6 3 50 5 3 6 4 70 4 4 6 5 90 9 5 6 6 110 11 6 6 F 130 13 7 6 8 140 14 8 6 9 160 16 9 6 10 180 18 10 6 al 200 20 11 6 12 220 22 12 6 13 230 23 13 6 14 250 25 14 6 15 270 27 15 6 16 290 29 16 6 17 310 31 17 6 18 320 32 18 6 19 340 34 19 6 20 360 36 20 6 21 380 38 21 6 22 400 40 22 6 23 410 41 23 6 24 430 43 24 6 25 450 45 25 6 26 470 47 26 6 27 490 49 27 6 28 500 50 28 6 29 520 52 29 6 30 540 54 30 6 21l 560 56 ol 6 32 580 58 32 6 33 590 59 J9 6 34 610 61 34 6 35 630 63 2 6 36 47 650 850 65 85 36 4 48 65 860 1170 86 117 36 5 66
18. too early and three horizontal lines ap pear in the time display m Press the ON OFF button to turn the machine off After 5 seconds turn iton again Select a program and Start the machine Problem solving guide m Ifthe lines are still displayed call the Miele Service Department The Spray arm indicator lamp flashes The middle spray arm is obstructed by an item in the basket The spray arm jets are blocked see Cleaning and care The opening in the center of the cut lery tray is covered restricting the flow of water to the middle spray arm Shortly after starting a program the Water Intake indicator lamp flashes The water shutoff valve is closed The water intake filter is clogged see Cleaning and care Joo little water may be entering the machine This may be due to insuffi cient water pressure 39 Problem solving guide The dishes are not clean The dishes are incorrectly loaded The correct amount of detergent was not used see Program chart The filters in the wash cabinet are not clean or the spray arm jets are blocked see Cleaning and care he wrong program was selected see Program chart White residue is visible on cutlery and dishware No salt in the salt reservoir Salt reservoir lid has not been screwed on properly Not enough rinse aid was used Water
19. 70 1190 1260 119 126 36 6 factory setting 11 Water softener To set the water softener for a hard ness level of 1 35 gr gal m Check that the water hardness selec tor in the wash cabinet is set to set ting 6 m lurn the dishwasher off m urn the program selector knob to the STOP position m Press the Delay start and START buttons at the same time while turn ing the machine on A P and a num ber will appear in the time display m Set the program selector knob to the NORMAL 55 130 position The number 22 will appear in the time display 22 The factory setting for a water hardness of 22 gr gal 12 m Press the Top Solo button as often as necessary until the value of your water hardness in gr gal appears in the display Example For a water hardness of 30 gr gal Keep pressing the Top Solo button until 30 appears in the time display After the figure 36 is reached the counter returns to 0 Value O must not be set m Press the START button twice to store the change in memory Setting the water softener for a hard ness level of 36 70 gr gal requires the following two step procedure 1 m turn the dishwasher off m urn the program selector knob to the STOP position m Press the Delay start and START buttons at the same time while turn ing the machin
20. Existing plumbing Do not under any circumstances cut the intake hose If the hose is cM cut the dishwasher will not work you will have a water leak and you could be injured If the hose is too long coil it neatly and place it be hind the machine If the standard 3 8 copper plumbing for a dishwasher already exists with a com pression fitting and valve as pictured m Cut the 3 8 copper tubing after the valve m Install the 3 8 compression to 3 4 MHT Male Hose Thread adapter Supplied with the machine as illus trated m Connect the inlet hose to the existing valve adapter assembly Electrical wiring and components Should not come into contact with any plumbing fixtures or hoses oF Plumbing Drain system specifications The machine comes equipped with A5dft long 1 5 m flexible drain hose with an internal diameter of 7 8 22 mm A built in swivel connector which allows the drain hose to be routed in any direction A built in non return valve on the dis charge side to prevent waste water from flowing back into the dish washer A built in odor trap on the discharge side to prevent odors from entering the kitchen Maximum drain height 3 ft 1 m Maximum drain hose length 12 ft 3 5 m Do not shorten the drain hose Electrical wiring and components should not come into contact with any plumbing fixtures or hoses IMPORTANT The dishwasher should be con
21. Miele NOVOTRONIC Operating instructions for dishwashers To prevent accidents and reduce the risk of damaging the machine read the Operating Manual before installing or using the machine M Nr 04 390 922 Contents Guide to the appliance 0 0 0 0 one 3 Important safety instructions nauau aaa 6 Caring for the environment 00 0 0 eee 8 Before using for the firsttime 00 00 00 ee 9 Opening and closing the door aaa 10 Water softener 00 0 eee 11 Setting the water hardness Filling the salt reservoir 0004 12 14 Sal IMOICAIOMIGIMO a 5 kad gee Se ahatns had ea so Hehe Reet Mae ae bo ee eo eee 15 Adding rinse aid eR He he 2 Ee Pee be OES HES 16 Loading the dishwasher 0 0 ccc eee 18 Loading examples incur arichoe Ge doe and trun Ga Gon d Loe hae dp ond te hare dune amp Both bate 19 AO USUNG the upper Daske aac ive boat otis bead bo whee te bk eS ted wade 22 Items not suitable for dishwashers 0 0 00 0 eee 23 Adding detergent Laaa aaa eee 24 Choosing a program uaaa aaa ee ee 25 Program CHala perac a oot ele ea ee A ee ae 26 Operating the dishwasher 0 0 0 0 0c ccc een 28 Changing programs interrupting a program program sequence indication 28 29 Additional features 0 0 0 0 ee eee 30 Unloading the dishwasher 0 0 0 00 ccc ee 32 Clean
22. RT button 18 The indicator lamp next to the START button will go out and the program will Start 28 15 16 1f 18 19 20 21 Note The time displayed may vary using the same program When the dishwasher is turned on it will display a Wash time calculated using a water supply tem perature of 60 F 15 C the tempera ture used for factory testing With subsequent programs the dish washer will recalculate the time accord ing to actual conditions The most cur rent value will then be displayed the next time the dishwasher is turned on The time remaining is displayed as the program progresses To prevent children from coming into contact with detergent only place it in the dispenser immediate ly before starting the program Program end The program has finished when no indi cator lamps are illuminated and a 0 appears in the display the dishwasher can now be unloaded If the dishwasher door remains closed the drying fan will continue to operate for a few additional minutes to help dissipate any remaining moisture Turning off At the end of a program m urn the program selector knob to the STOP position If any appliance will not be used for an extended period e g while on vaca tion it is recommended that the water supply valve be shut off Your Miele dishwasher is designed to shut off the water flow and drain the machine in the rare event of a valve failur
23. Taller mugs and glasses can be placed under neath the rack Do not cover the funnel in the middle of the upper basket The spray arms must not be blocked by items which are too tall or hang through the baskets If in doubt test for free movement by manually rotat ing the spray arms some food items may contain natural dyes that can discolor plastic items in the dishwasher e g carrots to matoes ketchup etc The stability of plastic items is not affected by this discoloration some loading examples are shown on the following pages Note If the additional feature Top Solo has been selected with a wash program all items must be loaded into the upper basket and cutlery tray See the Addi tional features section for further infor mation In areas where the water has high mineral content it may be necess ary to polish silverware after wash ing to achive a high shine Loading examples mee an WANED GANS oe ANS a CN es See Upper basket For small lightweight or delicate items such as cups saucers glasses des sert bowls etc Bottom basket For larger and heavier items such as plates serving platters and Saucepans Glasses should only be placed in the bottom basket if the special glassware insert is used Loading the dishwasher Cutlery tray The easily loaded cutlery tray ensures thorough cleaning of cutlery and cook ing utensils In addition the
24. West Coast Regional Headquarters 1900 South Norfolk Street Suite 101 san Mateo CA 94403 Phone 415 571 9074 Fax 415 571 9188 Mid West Regional Headquarters 3100 West Dundee Road Suite 901 Northbrook IL 60062 Phone 847 714 9433 Fax 847 714 9434 Alteration rights reserved G885 000 0697 These instructions are printed on 100 recycled paper and are completely Biodegradable
25. able the wash pro grams can be changed to take advant age of this development to help reduce your energy costs 41 Accessories Bottle holder depending on model A bottle holder for milk or baby bottles is available for use in the lower basket To achieve the proper cleaning results the bottle holder should only be placed in the positions marked with white Do not place them in the X marked posi tions Glass insert for the bottom basket provides the ability to safely wash glasses in the bottom basket Only available for models with remov able inserts in the lower basket Glass insert for the upper basket provides special support for long stemmed glassware 42 The i model dishwasher is specially designed for installation under a con tinuous countertop A panel can be custom made for instal lation on the front of the dishwasher as suring a perfect match with the kitchen cabinetry If a standard non cabinet matching dishwasher installation is desired the i model dishwasher can be converted into a U model through the addition of a GDU 60 65 decor set The decor set comes supplied with separate installa tion instructions To ensure stability these dish washers should only be installed under a continuous Countertop which is securely fastened to the cabinet base units Dimensions 1 with 35 2 with 33 1 8 890 mm machine height 840 mm machine height
26. cutlery tray insert is removable and can be carried to a drawer or table for easy loading or unloading thereby eliminating much of the handling of the cutlery The plate inserts on the left and right rear of the lower basket are removable To remove push the handles of both in serts toward the inside of the basket Once removed the open area can ac commodate large pots casserole dishes or accessory inserts see Ac cessories Loading the dishwasher To make unloading easier cutlery can be grouped in zones one for knives one for forks etc spoon heads should be placed so that water can run off them freely 20 x X J y lt S L A TER i e L gt n a ISI I I IEP LARAN i LE EE AOLO LA Ssn LS Lak _ AS L gs Place the heads of cutlery with round or oval handles in the holders This will secure them during the wash cycle Ensure that sooon heads are in contact with at least one holder so they cannot flio over and collect water Do not cover the opening in the middle of the cutlery tray and make sure that the upper spray arm can rotate freely after the tray is slid in otherwise the rotation of the spray arms may be inadequate for a thorough cleaning Loading
27. d indica tor lamp comes on m Press the button in the direction of the arrow until the flap springs open 16 Adding rinse aid Setting the dosage m Close the dishwasher door halfway The dosage selector comes factory set and pour liquid rinse aid into the stor to 3 It can be adjusted from 1 to 6 de age container until it is visible on the pending on your requirements surface of the screen Do not add aid until the Rinse aid indicator lamp comes on m Use a higher setting if spots appear on dry glassware m f streaking appears on dishes or Only use rinse aid specifically glasses use a lower setting labeled for residential dishwashers Inadvertently using powder or liquid detergents will damage the rinse aid dispenser m Close the flap and wipe up any spilled rinse aid The flap will remain closed during normal operation Loading the dishwasher 18 Load the dishes so that water can contact all surfaces Do not place dishes and cutlery in side other pieces where they may be concealed Hollow items such as cups and glasses should be inverted and placed in the upper basket Concave based Items should be placed at an angle on top of the cof fee bar See page 21 so that water can run off them freely Tall narrow hollow pieces should be placed in the center of the basket rather than in the corners to ensure water coverage small cups and glasses should be placed on the cup racks
28. e In order for this func tion to be active the door must be shut the machine must be ON and the Program knob must be in the STOP position Sequence indicator 20 Once a program has started the se quence indicator lamps 20 show the actual program stage reached by the dishwasher Note When required the water softener reactivation process is performed before the wash program It may last several minutes and occurs in intervals During this process only the Sof tener indicator will be on The hardness of the water supply will dictate how often after how many washes the water softener needs to be reactivated For example with a water hardness of 21 gr gal reactivation will take place after every 3 programs With a water hardness of 8 gr gal reactivation Operating the dishwasher will only take place after 11 programs Interrupting a program A program can be interrupted by open ing the door lf the door is then closed the program will continue from the point it was at be fore the door was opened Warning The water in the dishwasher may be hot and steam may be present Only open the door if absolutely necessary and exercise extreme caution when doing so The danger of burns and scalding exists Once the door has been opened allow 20 30 seconds for the inter nal temperature to equalize before closing it again and make sure it clicks into place Changing a program A
29. e on A P and a num ber will appear in the time display m Set the program selector knob to the NORMAL 55 130 position The number 22 will appear in the time display 22 The factory setting for a water hardness of 22 gr gal m Press the Top Solo button as often as necessary until the value 36 ap pears in the display m Press the START button twice to store the 36 in memory 2 The water hardness selector in the wash cabinet must be set according to the following chart value water gr gal ppm af for hardness program selector ming Setting 36 47 650 850 65 85 36 4 48 65 860 1170 86 117 36 5 66 70 1190 1260 119 126 36 6 factory setting Water softener Example The water hardness is 60 gr gal The water hardness selector in the wash cabinet must be set to 5 48 65 gr gal Using a screwdriver m Remove the cover from the water hardness selector m Adjust the water hardness selector as necessary There will be a click as each setting is reached Do not set the selector on setting 1 3 m Replace the cover on the water hard ness selector 13 Water softener Filling the salt reservoir The salt reservoir should be filled be fore the first use and when the Salt in dicator lamp lights up Use water sof tener reactivation salt 1 4mm grain size as other salts may contain in
30. e that the dishwasher be pulled out of its opening For this rea son perform the plumbing and electri cal connections after the machine has been levelled and the front panel has been mounted Install the slides Two slides are included and should be installed on the feet of the dishwasher m Push the machine into the opening before the machine is pushed under making sure the electrical cable and the countertop This will allow the ma hoses can reach their connection chine to slide easier protect the floor points without being kinked and allow adjustment of the rear level ing legs from the front of the machine 44 Dishwasher installation m Adjust the rear leveling legs to the re quired height To raise the machine turn clockwise To lower the machine turn counter clockwise several turns may be needed to set the correct height m Adjust the front leveling legs by push ing on the foot with a slotted screw driver m Tipping the machine slightly if possible will make adjusting the front legs easier Make sure the machine is level when adjustments are complete The dishwasher should be raised until it just touches the underside of the counter top 45 Dishwasher installation 3 Installing the control panel The control panel and hardware is packaged separately from the dish washer It should be installed using the following procedure If the GDU decor set is being used to
31. el with four spacer bars In special circumstances a fifth spacer bar optional accessory can be used to increase the panel height to 6 154 mm m After adjusting the control panel height cut off the plastic screw ex cess 5 Installing the custom door panel A custom door panel matching the kit chen cabinetry can be installed on the dishwasher by using the provided bracket Length Width 21 25 3 4 53 3 65 4 cm 23 1 2 59 8 cm Note The maximum panel length is only applicable when no spacer bars are used If a Stainless Steel panel is being used please follow the separate installation instructions included with the panel After panel installation see Step 6 Ad justing the door springs Proceed as follows m Measure the distance X between the lower mounting hole on the dish washer front door see inset arrow and the lower edge of the neighbor ing cabinet door 4 7 Dishwasher installation Place the door panel on a flat sur face good side face down taking care not to scratch the surface Make certain that the bottom of the panel is closest to you Using a pencil lightly draw a center line from top to bottom Using the previous measurement draw a horizontal line X inches above the bottom of the panel Important Make certain the line drawn using measurement X is located at what will be the bottom of the panel when it is attached to the dish
32. en gas may be produced ina hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period turn on all hot water faucets and let the water flow from each for several minutes before using the dishwasher This will release any ac cumulated hydrogen gas Do not smoke or use an open flame during this time Do not drink the water from the wash cabinet SAVE THESE INSTRUCTIONS Caring for the environment Disposal of the packing material The cardboard box and packing ma terial protects the appliance during shipping It has been deliberately de signed to be biodegradable and recy clable Please dispose of these ma terials as you would any other recyclable products Disposal of your old machine Old machines contain materials which can be recycled Please contact your local recycling center or scrap mer chant about the possibility of recycling these materials and make certain the machine has been made child resistant as outlined in the Important safety in stuctions before disposing of the ap pliance Energy saving washing These dishwashers are exceptionally ef ficient in their use of water and elec tricity You can make the most of your appliance by following these tips m Make full use of the baskets without overloading the dishwasher for the most economical washing m For small loads select the Top Solo funct
33. ightened If the door closes the springs need to be loosened The adjusting screw is located in the upper front strip on the left hand side of the dishwasher m Open the dishwasher door m Adjust the door springs to the cor rect balance turn clockwise to tightened turn counterclockwise to loosen Dishwasher installation 7 Securing the dishwasher to the countertop To ensure the stability of the dish washer it must be attached to the countertop after it has been positioned Open the dishwasher door Using the screws provided fasten the dishwasher to the countertop through the two holes located on the Upper rim The weight of the machine must be supported by the legs not the countertop fastening screws If securing the top takes the weight off of the legs extend the legs further until they are tight against the floor Do not drill any additional holes through any portion of the wash cabinet If in doubt about how to se cure the dishwasher please call the Miele Service Department 49 Dishwasher installation lf the edge of the countertop is too nar row or the machine is being installed under a cut out area use the securing bracket provided the countertop about 4 10 cm m Position the securing bracket m Push the dishwasher back Into the opening and secure it through the hole in the bracket SO For Corian or granite countertops fasten the di
34. ilt into the water inlet system to prevent potable water mixing with waste water Recommended temperature Water pressure 56 Hot water connection New plumbing The water inlet hose comes equipped with a 3 4 female hose thread connec tor This can be directly connected to a shut off valve with 3 4 male hose thread ends It is preferable that the hose assem bly be installed vertically so the hose exits from the bottom of the valve box If this is not possible it can be installed hoizontally provided the hose exit re mains beneath the main body of the box see illustration The lightning bolt should be above the arrow when the installation is complete The valve box should also be installed so that it is at least 8 24 cm above the floor or base of the cabinet and so the excess coiled hose will remain lower than the box at all points A 2 x 4 60 x 115 mm cutout in either the side or bottom of the cabinet adjoin ing the dishwasher is necessary if the valve box needs to be passed through Plumbing The water pressure must be between 4 5 and 145 psi 0 3 and 10 bar If the water pressure is too low the ma chine may not take in enough water in the alloted time and the Water Intake in dicator lamp will flash If this occurs the water intake time can be increased see Problem solving guide lf the water pressure is too high a press ure reducer must be installed
35. ing and Care 0 0 cee ee 33 Problem solving guide 0 0 eee 39 After sales service Sos wars BOs be oid Cas ower hs oe oe Stes 4 Accessories L Laaa a 42 Dishwasher installation 0 0 0 0 aaa eee 43 Electrical connection auauna aa eens 54 PIUINDING reena naoa ae aee ee ee ee a en ee ee eee eee ore 56 Technical data 6 0 0 0 eee 60 Guide to the appliance Miele dishwashers are available in two versions 1 Integrated i dishwashers dishwashers are designed for instal lation under a continuous countertop The control panel with its accessories is included with the i dishwasher in a separate package for on site installa tion The front is designed to accept a custom made panel matching the exist ing kitchen cabinets Installation directions can be found In the Installation chapter 2 U dishwashers The built under U dishwashers use the integrated i dishwashers as the basic machine By using a decor set GDU the i dish washer can be converted into a U model dishwasher GDU installation instructions are in cluded in a separate pamphlet sup plied with the decor set Guide to the appliance SS _ QS RRBRECOGI aE majal AUO N TE NEE 00 i O L i i NO ak Oo TURBOTHERMIC PLUS 14 15 16 Tf 18 19 20 21 O O ADA N O OT A UO PO
36. ion see Additional features chapter m Choose a program that best suits the degree of soiling and the type of dishes being washed m f baskets are only half full use the ECONOMY program m Use the correct amounts of deter gent and rinse aid Before using for the first time Before using for the first time please note the following points Setting the water softener The water softener must be set to corre spond to the water hardness in your area This can be obtained from your local water company or by using a test kit that can be purchased from the Miele Parts Department The salt reservoir must only be filled with water and salt Never fill it with detergent Adding rinse aid Inadvertenily filling the rinse aid reservoir with liquid or powder deter gent will damage the reservoir Only use detergents and rinse aids for mulated for domestic dishwashers It is important to choose the correct program Different wash programs should be se lected for different loads and different degrees of soiling See the program chart for further program descriptions When the dishwasher is run for the first time the selected program will not start for approximately 7 minutes During these 7 minutes the Water softener reactivation program is run and the Softener indicator lamp will be on Add the correct amount of detergent Follow the detergent manufacturer s recommendations on how much deter
37. nt Connection Hard Wiring For hard wiring the power cord must be disconnected from the terminal box located at the lower left front of the dish washer behind the toekick and service panel Pass the permanent power sup ply cable through the strain relief and secure it to the terminal box Connect L1 Black to L on terminal block N White to N on terminal block GRND To ground connector GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE PROPERLY GROUNDED Warning Hardwiring the dishwasher should only be done if required by local electrical codes and then in a manner consistent with those codes Do not cut the plug off the power supply cord and connect it directly to the house wiring 99 Plumbing It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances All dishwashers that carry the following blue and white sticker are designed to shut off the water and drain the wash chamber in the rare event of an internal water valve failure In order for this function to be active the door must be shut the machine must be ON and the Program knob must be in the STOP position u E Waterproof System Hot water supply specifications 120 F 49 C Maximum temperature 140 F 60 C 14 5 145 psi 0 3 10 bar An air gap is bu
38. oo C 130 F preliminary pre wash for heavy soiling INTENSIVE same as INTENSIVE 55 C 130 F but at a 20 80 100 65 C 150 F higher wash temperature for stubborn dried on particles and lightly soiled pots and pans Special programs ENERGY SAVER Only select ENERGY SAVER if the dish 20 80 100 washer is connected to a hot water supply minimum temperature 45 C 115 F see chapter Choosing a program POTS amp PANS For pots pans and dishware with dried on 20 100 120 TO G V70 F particles of food and very heavy soiling ECONOMY For half a normal everyday load or 55 C 130 F for full loads with very light soiling e g 50 9 50 9 coffee cups CHINA amp CRYSTAL Gentle program for lightly soiled and 45 C 115 F heat sensitive tableware 50 2 50 2 SHORT Quick program for lightly soiled vores 4 lead dishware e g party dishware 50 50 RINSE amp HOLD For rinsing dishes when a complete cycle is not needed The dispensing method will depend on the type of detergent being used A Use this method for detergents which contain phosphates and chlorine Divide the total amount as shown between compartment and compartment Il B Use this method for detergent which is chlorine and phosphate free detergent which is chlorine free but contains phosphates In this instance the whole amount is placed in compartment Il 3 Use half of the manufacturer
39. owder detergents formu lated for residential dishwashers Do not use gels or liquid deter gents m Press the latch on the detergent dis penser The cover will soring open m Fill the dispenser using the amount of detergent recommended by the detergent manufacturer m Close the cover The cover will al ways be open at the end of a wash program excluding the RINSE amp HOLD program 24 Generally filling the dispenser with detergent will be sufficient to ensure thorough cleaning If dishes are extra dirty or if the soil has been allowed to dry on the dishes before washing a program utilizing a prewash cycle should be selected In this case extra detergent can be added to the small compartment labeled in the center of the dispenser Dishwasher detergents contain irri tant and corrosive ingredients They can cause burns in the mouth and throat if swallowed or inhibit brea thing Keep children away from detergent and from the dishwasher when the door is open To avoid the danger of children com ing into contact with dishwasher detergent only fill the detergent dis penser immediately before starting the program Capacities Compartment orewash takes a maxi mum of 1 ounce 25 ml and Compart ment II main wash takes a maximum of 3 ounces 80 ml when completely filled There are horizontal marks to as sist you in filling Compartment II The marks indicate a level of approximately 3 4 1
40. program can be changed at any time The new program will start as soon as it has been selected m urn the program selector knob to the desired program If you wish to start the new program at its beginning m urn the program selector knob to STOP a point will appear in the display field m Select the new program and press START It may be necessary to add additional detergent depending on where the original program was interrupted 29 Additional features Miele TURBOTHERMIC PLUS Delay start 18 The starting time of a program can be delayed up to 9 hours and 30 minutes in 30 minute increments in order to take advantage of off peak utility rates that exist in some areas To set a Delay time m Select a program The length of the program is displayed 17 in minutes and seconds m Press the Delay start 18 button once for every 30 minutes of delay desired The program length displayed will now change to a display of the Delay time also in hours and minutes The Delay start indicator lamp will illuminate 30 15 16 17 18 19 20 21 m Press the START button 18 The dishwasher counts down the minutes of the chosen delay then starts the program automatically Once started the display will show the time remaining in the wash program Example Press Delay start once for a 30 minute delay 30 mins is displayed Press Delay start
41. r of insoluble substances we re commend installing a filter between the valve and the inlet hose connection These filters can be obtained from the Miele Parts Department Cleaning the control panel m Ihe control panel can be cleaned using a damp cloth and mild deter gent Do not use abrasive all purpose or glass cleaners as their use may damage plastic surfaces Cleaning the door panel m Plastic laminate panels should be cleaned using a suitable non ab rasive cleaning agent or mild soapy water m Panels made from wood should be cleaned using a soft damp cloth and an appropriate wood cleaner 38 With the aid of the following guide minor problems can be easily cor rected If you are unable to correct the problem please contact the Miele Ser vice Department Any work on the electrical compo nents of the appliance should only be performed by a qualified and trained person in accordance with local and national regulations Un authorized or incorrect repairs could cause personal injury or dam age the machine Problems possible causes The dishwasher does not start The door is not properly closed The plug is not properly inserted The circuit breaker is defective or has tripped The wash cycle finishes too early and the Drain indicator lamp flashes The drain hose is kinked The drain pump is blocked see Cleaning and care The wash cycle finishes
42. r the appliance be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance itself will be located An opening through the partition be tween the compartments of 1 to 1 1 2 3 to 4 cm can be made to allow the plug to pass through m Make certain that there are no rough edges that could damage the power cord If metal cabinets are used place the supplied rubber grommet around the edge of the opening be fore passing the cable through 54 m Exercise care when pulling the dish washer in or out SO as not to dam age the power cord or hoses GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE PROPERLY GROUNDED In the event of a malfunction ground ing reduces the risk of electric shock by providing a path of least resistance for the electric current This appliance is equipped with a cord that has a grounding conductor and plug The plug must be connected to an appropri ate outlet that has been installed and grounded in accordance with all local and national codes and regulations DANGER Improper installation of the electrical outlet or im proper grounding can result in the risk of electric shock Check with a qualified electrician if you are in doubt as to whether the ap pliance is properly grounded Do not modify the plug provided with the appliance If it will not fit the outlet have the correct outlet in stalled by a qualified electrician Electrical connection Permane
43. s recommended amount of detergent 26 Program cycle USAGE Electric kWh Water ale 2 Prelimi Pre wash Main Interim Final Drying Water hot Liters nary pre wash rinse rinse 49 C Gallons wash 120 F X X X X X 0 9 19 5 0 X X X X X 1 13 19 5 0 X X X X X X 0 89 24 6 3 X X X X X X 0 98 24 6 3 X X X X X X 0 20 24 6 3 X X X X X IAs 19 5 0 X X X X 0 75 14 3 7 X X X X X 0 47 19 5 0 X X X 0 56 14 3 7 X 0 06 5 1 3 4 Average consumption values are for a water hardness of up to 17 gr gal 5 With half loads 7 place settings X cycle used et Operating the dishwasher TURBOTHERMIC PLUS Turning on m Close the door m Open the water valve if it is closed m Press the ON OFF button 14 When the program and temperature se lector knob 21 is in the STOP posi tion a dot will light up in the display field 17 Starting a program m urn the program and temperature selector knob 21 clockwise or counterclockwise to the desired pro gram The length of the selected program ap pears in hours and minutes in the Time display 17 At the same time the indicator lamp next to the START button 18 illumi nates m Before starting the program addi tional features Delay start or Top Solo can be selected see Addi tional features on page 30 m Press the STA
44. shwasher to the adjacent cabinets as follows For openings greater than 23 5 8 60 cm wide m Pull the dishwasher 4 10 cm out of its Opening m Insert the tab of each optional mount ing bracket into the guide hole on top of the dishwasher and then swing it to the right or left as re quired Push the dishwasher back into its open ing align and fasten it to the adjacent cabinets using 2 screws for each bracket For openings 23 5 8 60 cm wide m Open the dishwasher door and remove the caps covering the mount ing holes on the outer edge of the wash chamber m Fasten the dishwasher to the aa jacent cabinets using the supplied screws and bushings Make sure a bushing is placed over the screw be fore inserting it into its mounting hole m lighten the screws and replace the Caps The side mounting holes should only be used for securing the dishwasher if the opening is 23 5 8 60 cm wide Use of this method on larger openings will damage the machine and cause leaks Dishwasher installation 8 Installing the toekick For kitchens utilizing one continuous toekick To prevent damaging the front panel and before installing the toe kick measurements must be taken to ensure that the toekick will not in terfere with the complete opening of the dishwasher door The panel overhang P and toekick depth of recess R determine the maxi mum dishwasher toekick height H
45. so luble additives which can impair the functioning of the softener The salt reservoir holds approx 4 Ibs 2 kg of salt Inadvertently filling the salt reservoir with dishwashing detergent will damage the water softener Make sure that only water softener reacti vation salt of the proper grain size is used m Remove the lower basket m Unscrew and remove the salt reser voir Cap 14 Before filling the salt reservoir for the first time Fill the salt reservoir with approxi mately 2 quarts 2 of water Place the funnel provided over the salt reservoir Carefully fill with salt As it is filled water will run out Clean any excess salt from the threads of the reservoir opening screw the cap on firmly If the dishwasher will not be used im mediately after reactivation run the RINSE amp HOLD program This will remove any traces of salt from the cabinet Salt indicator CHECK O Sprayarm O Water Intake O Drain Doo Salt ORinse aid When the salt reservoir is empty the Salt indicator lamp will light notifying you that the reservoir should be refilled with reactivation salt After the reservoir has been filled the water softener is automatically reacti vated the next time the dishwasher is run The Softener indicator lamp illumi nates during this process Note If the water used Is very soft below 4 gr gal the salt indicator lamp will stay on In this
46. suitable for dishwashers Cutlery with wooden handles Wooden cutting boards Glued items such as old knives with handles that are glued together around the shank of the blade Hand made craft items Copper or tin items Plastic items which are not heat resis tant Please note Silver or aluminum items may suffer some discoloration Aluminum parts eg oven hood grease filters should not be cleaned using commercial or industrial deter gents These high alkaline deter gents may damage the machine and in extreme instances Cause ex plosive chemical reactions silverware previously cleaned with a silver polish may be damp or spotted at the end of a program where water has adhered to the pol ish This can be rubbed off with a soft dry cloth Silver that has pre viously been cleaned in an immer sion dip is usually dry at the end of a program but may discolor tarnish Colors on dishware that have been painted over the glaze may fade over time Clouding may occur on glasses after frequent washing Miele recommends m Wash delicate glassware using the ECONOMY program or the CHINA amp CRYSTAL program with a tempera ture of 45 C 115 F if So equipped This will reduce the risk of clouding There are no standard guidelines for washing glassware When in doubt wash by hand When purchasing new dishes and cutlery make sure they are dish washer safe 23 Adding detergent Use only p
47. th the toekick of the adjoining cabinets The toekick cannot be pushed back in It must be unscrewed so that the tension on the spring clips can be released The brackets can then be pushed in and the toekick re attached Dishwasher installation Carefully open the dishwasher door until it hits the toekick Using the front lower edge of the door panel as a guide draw a line across the toekick Unscrew and remove the toekick If one of the cutting lines is close to the line just drawn score the front of the toekick and snap off the excess or trim the toekick along the line using a Saw Screw the toekick back onto the brackets with the cut edge at the bottom If the dishwasher door does not open completely the toekick may need fur ther trimming 93 Electrical connection It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances Disconnect the appliance from the power supply before servicing the ma chine by pulling the plug or turning off the circuit breaker Specifications Power Supply 120 VAC 60 Hz Rated Load 12 5A 1500 W Circuit breaker 15 AMPS The unit is equipped with a 5 ft 1 5 m power supply cord for connection to a 120 V 15 AMP grounded receptacle Using an outlet m It is recommended that the power outlet fo
48. washer 48 The mounting bracket is marked in the middle Lay the bracket on the rear side of the door front so that the mark in the middle of the bracket aligns with the vertical guide line and the lower holes of the bracket are centrally positioned in the hori zontal guide line see illustration Use strips of adhesive tape to hold the bracket in this position Mark and drill pilot holes for the screws using a 3 32 2 5 mm drill bit m Attach the bracket to the panel using the 4 screws provided m Double check the location of the bracket before mounting the panel to the dishwasher Attaching the panel m Pull the dishwasher out from under the countertop about 4 10 cm If the dishwasher is installed at the end of the kitchen cabinets Pull the machine out as far as is necessary to reach the 4 locking screws lo cated on the edge of the door m Attach the panel to the dishwasher by aligning the bracket tabs with the slots on the door m Straighten the panel and lock it into place by tightening the 2 locking screws on each edge of the door m Use the provided caps to plug the locking screw access holes m Push the dishwasher back under the countertop and proceed to Step 6 Adjusting the door springs 6 Adjusting the door springs The door springs are adjusted correctly when a half opened door remains in that position when released If the door drops down the springs need to be t
Download Pdf Manuals
Related Search