Miele DA 249-4 User's Manual
Contents
1. 8 7 16 pa 280 mm 11 106 mm 4 3 16 20 mm 7 8 PAM Y 270 mm om el Y 105 8 11 1 4 369 mm K Z N 14 1 2 500 mm 19 11 16 250 mm Y 9 13 16 900 mm 35 7 16 32 Appliance dimensions 1 Air outlet installed upwards for recirculation mode We 2 and 3 Cut out area in wall or ceiling for entrance of 6 7 150 mm ductwork or 5 125 mm ductwork with a reducing collar For recirculation mode only 2 and outlet installation are necessary Do not install this exhaust hood over cooktops burning solid fuel When installing the hood make sure that the following minimum distance S between the top of a cooking surface and the bottom of the hood is 22 55 cm above electric cooktops 26 65 cm above gas cooktops 26 65 cm above an open grill Follow the safety distances recommended by the cooktop manufacturer in their installation and operating instructions If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance See Warning and Safety instructions for further information 26 65 cm is recommended for all installations to allow for optimum work space under the hood Distance between cooktop and hood S The installation procedure differs depending on the model and venting method Before beginning t2. button to select the desired time 5 dS 15 ee e O m Store the selection by pressing the charcoal filter button If the procedure is not stored within 4 minutes of programming the hood will automatically default to the old data Cleaning and Care Before cleaning or servicing the hood disconnect it from the power supply by either removing the fuse unplugging it from the outlet or manually tripping the circuit breaker Cleaning the casing Warning Never use abrasive cleaners scouring pads steel wool or caustic oven cleaners on the hood They will damage the surface m All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a soft sponge m Wipe dry using a soft cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage m Glass surfaces can be cleaned using glass cleaner Avoid cleaning agents containing soda acids solvents or chlorides abrasive cleaning agents e g powder or cream cleansers abrasive sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents limescale removers These will damage the surface 18 Stainless steel Stainless steel surfaces can be cleaned using a non abrasive stainless steel cleaner To help prevent resoiling a conditioner for stainless steel can also be used Apply sparin
3. unplug it from the outlet and cut off its power cord to prevent hazards 27 Installation accessories 28 Installation accessories 0 2 protective shields prevent scratches to the chimney during installation 2 hose clips for securing the ducting 1 reducing collar for use with 5 125 mm exhaust ducting Upper retaining plate secures the chimney extension Middle retaining plate for additional stability of the chimney Lower retaining plate secures the canopy and motor assembly 2 Installation kit for recirculation mode contains diverter 2 grilles and an hose optional accessory Caution During the installation process please be careful of sharp edges that can cause harm Installation instruction sheet A 8 large headed screws 5 x 40 mm for securing the retaining plates and the canopy S8 wall anchors included in the packaging are not for use in USA CDN 2 M 6 locking nuts for securing the motor assembly Om 2 screws 3 9 x 7 5 mm for securing the chimney D200 2 screws M4 with locking nuts and plastic washers for securing the glass canopy ISS 1 allen wrench for adjusting the unit height and fixing the operating unit VA E 1 screw cover q c 1 lever for disassembling the chimney 29 Plywood backing The majority of the weight of the installed ventilation system will be support
4. 888 586 8056 Mielecare National Service Phone 800 565 6435 905 850 7456 Fax 905 850 6651 service miele ca Tech Service Alteration rights reserved 1106 M Nr 06 712 720 00 en US
5. The indicator goes out Automatic Safety Shut Off The fan will turn off automatically 10 hours after the last button was activated The lighting however will remain on m Press the On Off button to turn the fan back on again Operation Turning the lighting on off The overhead lighting can be turned on and off independently of the fan m Press the light button briefly to turn on the lighting The light button indicator illuminates m Press the light button briefly again to turn off the lighting The light button indicator will go out 14 Dimming the lighting The brightness of the lighting can be adjusted m While the lighting is turned on press the light button The lighting will dim until the button is released m If the button is pressed again the lighting will brighten until the button is released If the button is pressed continuously the light will cycle between bright and dark m Press the light button again to turn off the lighting Operation Filter timers Grease filter A timer monitors the hours of fan operation The indicator for the grease filter will light after 30 hours of operation The grease filter must then be cleaned After the grease filter have been cleaned and put in place the grease filter timer must be reset Le m To do this press the grease filter button for about 3 seconds The indicator will go out Charcoal filters Recirculatio
6. 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by Miele s Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at www store miele com Installation Instructions 26 Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping They have been designed to be biodegradable and recyclable Please recycle To prevent suffocation of children ensure that any plastic wrappings bags etc are disposed of safely and kept out of their reach Disposal of an old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Before discarding an old hood
7. If the power level indicators 1 and 4 flash the automatic switch back is not activated m To activate the automatic switch back press the button The power level indicators 1 and 4 light continuously m To deactivate the automatic switch back press the button 5 15 OO m To save the setting press the Delay Shut Down button If the procedure is not saved within 4 minutes of programming the hood will automatically default to the old setting 12 Fan performance The maximum air flow capacity is 625 cfm Factors such as narrow duct diameter and bends will affect this value Level 1 operates at 40 capacity Level 2 operates at 60 capacity Level 3 operates at 80 capacity Level 4 operates at 100 capacity There will also be a slight decrease in airflow for hoods operated in recirculation mode due to the active charcoal filter Operation Delayed Shut Down If odors or smoke remain in the kitchen after cooking has been completed the Delayed Shut Down feature can be selected to allow the hood to continue running for either 5 or 15 minutes 5415 OO m Press the Delayed Shut Down button while the fan is still running Press once 5 minute delay left indicator lights Press twice 15 minute delay right indicator lights To cancel the Delayed Shut Down feature press the button again Turning off the fan D oj m Press the On Off button to turn the fan off
8. cooking odors outside 10 Recirculation mode RR Air is drawn through the the decor panel grease filter and an active charcoal filter The filtered air is then recirculated back into the kitchen through a vent at the top of the hood s chimney The recirculation mode requires an install kit and charcoal filter which are optional accessories Before using the hood in recirculation mode ensure that the active charcoal filter is in place see Cleaning and care Operation Turning on the fan D e m Press the On Off button The fan runs at power level 2 The On Off indicator lights Selecting the power level 000 m Use the controls to select the desired power level increases the fan speed decreases the fan speed Level 1 to 3 green indicators are usually sufficient for normal cooking Intensive setting Level 4 yellow indicator should be used for a short period when frying or cooking food with a strong aroma Automatically switching back the Intensive power level The intensive level 4 can be programmed to automatically switch back to level 3 after 10 minutes Turn the fan and the lights off 5415 00 Press and hold the Delay Shut Down button for 10 secs The first indicator lights Press the following buttons one after another light 0000 the button and the light button again Operation 0000
9. 5 or 15 minutes 3 Grease filter button The indicator next to the grease filter button lights when the grease filter and decor cover need to be cleaned This button is also used toreset the grease filter timer after cleaning the grease filter see Cleaning and Care to show how long the grease filter have been in use see Operation Filter timers to change the number of hours counted by the grease filter timer see Operation Reprogramming the filter timers Charcoal filter button The indicator next to the charcoal filter button lights when the charcoal filters need to be replaced This button is also used to reset the charcoal filter timer after changing the filters see Cleaning and care to show how long the charcoal filters have been in use see Operation Filter timers to change the number of hours counted by the charcoal filter timer see Operation Reprogramming the timers Functional description The hood offers two modes of operation Air extraction RER The air is drawn in and cleaned by the decor panel and the grease filter and directed outside The hood comes equipped with a non return flap This flap automatically closes when the hood is turned off so that no exchange of outside air and room air can occur When the hood is turned on the air pressure of the exhaust fan automatically opens the flap blowing the inside air and
10. Miele Operating and Installation Instructions Ventilation System DA 249 4 To prevent accidents and machine damage read these instructions before installation or use M Nr 06 712 720 Contents IMPORTANT SAFETY INSTRUCTIONS 4 Guide to the hood 8 Functional description nennen 10 Operators ae 2 Datu i d ee 11 Toming One TAM ee er en ai Aa ee ad A aia 11 Selecting the power level 11 Delayed Shut DOWN cicero ss 13 Turning OM Meta riada dada od bo kde aaa aaa Ad re 13 T rning the lighting ONION se ec e ene eee rau ae aaa ea en 14 Dimming the lighting 14 Filter IMET une u ai ogee an Ran Sac baie Sites ann Roe Deomm a a S 15 Checking the filter tiMers i 15 Reprogramming the timers i 16 Cleaning and Care ce 18 Cleaning the Casing sse e aa e Rea ue Faces qoe YER REY a ER 18 Grease filter i eue mo Re Race ace ERG fb weder naht 19 Active charcoal Ml a a dua pee ote Seb ee dae Poder bend 21 Changing the light bulbs Rer RR RO RR RR HERE E He RE que 23 After Sales Service e 24 Installation instructions 25 Caring for the environment 27 Installation accessories 28 Plywood backing suisses eee 30 Electrical data o osi ete atente PELLI LI BP e eie ES 31 Appliance dimensions 32 Installation 6 0 HI 34 Installation instructions 2 0 I 34 BIEN TERRITI 34 Air extraction 0 00 0 ees 35 Condensate trap 36 IM
11. PORTANT SAFETY INSTRUCTIONS Read these Operating Instructions carefully before installing or using the Ventilation System This appliance is intended for residential use only Use the appliance only for its intended purpose The manufacturer cannot be held responsible for damages caused by improper use of the hood This appliance complies with current safety requirements Improper use of the appliance can lead to personal injury and material damage READ AND SAVE THESE INSTRUCTIONS N CAUTION Use only for general ventilation Do not use to exhaust hazardous or explosive materials and vapors This appliance is designed to vent cooking smoke and odors only Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician The manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective grounding system Before connecting the appliance to the power supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent machine damage If in doubt consult a qualified electricia
12. a fire extinguisher ONLY if You have a Class ABC extinguisher and know how to operate it The fire is small and contained in the area where it started The fire department has been called You can fight the fire with your back to an exit IMPORTANT SAFETY INSTRUCTIONS Installation N WARNING To reduce the risk of fire only use metal ductwork When installing the hood follow the recommended minimum safety distances between a Miele cooktop and the hood 22 55 cm above electric cooktops 26 65 cm above gas cooktops 26 65 cm above an open grill If local building codes require a greater safety distance follow their requirement For non Miele cooking appliances maintain the safety distances recommended by the appliance manufacturer If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance Be careful not to damage hidden electrical wiring or plumbing when cutting or drilling into the wall or ceiling Do not use an extension cord to connect the appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating Do not install this hood over cooktops burning solid fuel Any fittings sealant or materials used to install the ductwork must be made of approved non flammable materials Never connect an exhaust hood to an active
13. and refinish the wall m Proceed to the included installation sheet to complete the installation Electrical data All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations Installation repairs and other work by unqualified persons could be dangerous The manufacturer can not be held responsible for unauthorized work Ensure that power to the appliance is OFF while installation or repair work is performed Verify that the voltage load and circuit rating information found on the data plate located behind the grease filter match the household electrical supply before installing the hood If there is any question concerning the electrical connection of this appliance to your power supply please consult a licensed electrician or call Miele s Technical Service Department 1 800 999 1360 1 800 565 6435 WARNING THIS APPLIANCE MUST BE GROUNDED Important The hood comes equippped with a 5 ft 1 5 m power cord with a NEMA 5 15 molded plug for connection to a 120 VAC 60 Hz 15 A power outlet Maximum load 390 W LORUN cts cette he Rad 2x20W Voltage s deest pesce we dy 120 V FREQUENCY pui dece eee de es 60 Hz Cif Cult rating eere 15A 31 Appliance dimensions 250 mm 9 13 4 6 35 mm 1 3 8 PAN y 1 106 mm 603 mm 23 3 4 4 3 16
14. ase the chimney from its hooks Air extraction WARNING Danger of toxic fumes Gas cooking appliances release carbon monoxide that can be harmful or fatal if inhaled The exhaust gases extracted by the hood should be vented outside of the building only Do not terminate the exhaust ducts in attics garages crawlspaces etc To reduce the risk of fire only use metal ductwork Please read and follow the IMPORTANT SAFETY INSTRUCTIONS to reduce the risk of personal injury Follow all local building codes when installing the hood Exhaust ducting and connections The ducting should be as short and straight as possible and the number of sharp bends should be minimized For most efficient air extraction the diameter of the ductwork should not be less than 6 150 mm Use of flat ducts also reduces the air extraction efficiency Noise levels of the hood will increase if flat ducts or round ducts of less than 6 150 mm in diameter are used Use smooth or flexible pipes made from approved non flammable materials for exhaust ducting Where the ductwork is horizontal it must slope away from the hood at least per foot 1 cm per meter to prevent condensation dripping into the appliance If the exhaust is ducted through an outside wall a Miele Telescopic Wall Vent can be used 35 Air extraction dai04060 If the exhaust is ducted into an inactive flue the air must be expelled para
15. before the timer has reached its maximum the charcoal filter button should be pressed for 6 seconds to reset the counter to zero 22 Cleaning and Care Changing the light bulbs m Remove the decor cover see Cleaning and Care Removing the Before changing the light bulbs decor cover disconnect the hood from the power supply by either removing the fuse unplugging it or manually tripping the circuit breaker m Pull the old bulb out of its socket and replace it with a new one of the same type Be careful not to drop the bulb on the cooktop When in use halogen bulbs become extremely hot and they can burn your hands Do not attempt to change the bulbs until they have had sufficient time to cool down Do not touch the bulb surface Fingerprints or body oils deposited on the bulb will decrease the life of the bulb Please follow the bulb manufacturers instructions 23 After Sales Service Repairs In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet m When contacting the Technical Service Department please quote the model and serial number of your appliance These are shown on the data plate which is visible when the grease filter is removed 24 MieleCare MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by
16. chimney dryer vent vent flue or room ventilating ductwork Seek professional advice before connecting an exhaust hood vent to an existing inactive chimney or vent flue Ducted fans must always be vented outdoors Make sure that the airflow in the room is sufficient for combustion and exhausting of all non electric heating appliances water heaters gas cooktops gas ovens etc otherwise backdrafts may occur Follow the heating manufacturer s guidelines and safety standards or those published by the National Fire Protection Association NFPA or the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE If in doubt consult an experienced professional Guide to the hood pf 7 LL6 ep E E E Mano Guide to the hood Chimney extension Recirculation vent For recirculation use with optional accessories 3 Chimney Canopy Overhead lighting 5 Active Charcoal Filter Available to purchase for use in the recirculation mode Grease filter Decor cover 9 Light button This button turns the light on and off and also dims the light The lighting can be used independently of the fan On Off button Fan power selection Four fan speed selection 42 Delayed Shut Down This button activates the Delayed Shut Down feature The fan can be set to turn off automatically after either
17. ease 2nd indicator from the left 30 hours which has accumulated over along 3rd indicator from the left 40 hours period of time will harden on the 4th indicator from the left 50 hours filters making cleaning more difficult Use the buttons to select the t desired time Reprogramming the grease filter timer D e m Press the On Off button to turn off the fan Le m Store the selection by pressing the grease filter button If the procedure is not stored within 5415 OO 4 minutes of programming the hood will automatically default to the old data m Press the Delayed Shut Down and grease filter buttons at the same time 16 Operation Reprogramming the charcoal filter timer The active charcoal filter can only be used in recirculation mode and can not be used to exhaust fumes The charcoal filter timer is not not preset Before using the hood in recirculation mode the charcoal filter timer must be programmed D e m Turn off the fan using the On Off button m Press the Delayed Shut Down and Charcoal Filter buttons at the same time 0000 The indicator for the charcoal filter and one of the indicators will flash The lit indicator shows the programmed time 1st indicator from the left 120 hours 2nd indicator from the left 180 hours 3rd indicator from the left 240 hours Ath indicator from the left deactivated m Use the
18. ed by the lower retaining plate It must be firmly attached to the stud framing behind the drywall If studs are not available in the required locations a plywood backing min 13 mm thick spanning at least two studs must be installed Failure to adequately support the weight as stated may result in the ventilation system falling off the wall causing personal injury and property damage If plywood backing is not needed proceed to the included installation sheet To install a plywood backing Ts D on D D 1 i igit 1 I DE Wall studs _ Var i uem Plywood backing screwed to wall studs Retaining plate dai1007 m Determine and mark the location of the retaining plate for the canopy as outlined on the installation sheet m Make a cutting line 3 76 mm above and 3 76 mm below the outline of the retaining plate 30 m Find the studs to the left and right of the mounting location by tapping the wall or using a stud finder m Mark a vertical cutting line along the center of each stud Be careful not to damage any wiring or plumbing that may be located behind the wall Make sure that the power supply to the area where this installation is being performed has been turned off at the breaker panel before cutting into the wall m Remove the drywall between the cutting lines and replace it with plywood of a matching thickness min 5 13 mm thick Tape the joints
19. emperature program e g Heavy Soil or Pots and pans Use the recommended amount of dishwasher detergent Overuse could destroy the filter Depending on the detergent cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface Performance of the filter will not be affected by this discoloration m After cleaning the filter can be placed on a towel to air dry m For cleaning the decor cover see Cleaning the casing m While the filter is removed clean any dirt or grease from the filter casing to prevent the risk of fire m After returning the grease filter press the grease filter button for 3 seconds to reset the timer The indicator light will go out 20 m f the grease filter is cleaned before the timer has reached its maximum the grease filter button should be pressed for 6 seconds to reset the counter to zero Inserting the grease filter dai0924b m Angle the grease filter into position toward the front of the hood m Once the front edge of the filter is in place push up the rear of the filter so that both sides click into place Inserting the decor cover dai0925 m Hook the decor cover on to the latches on the rear panel of the chimney Push the cover up at the front so that it clicks in place Cleaning and Care Active charcoal filters In recirculation mode an active charcoal filter must be used in addition to t
20. gly with even pressure Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly Do not use a stainless steel cleaner on these controls Cleaning and Care Grease filter The decor panel and reusable metal grease filter remove solid particles from the vented kitchen air grease dust etc The grease filter is visible when the decor cover is removed Le The grease filter should be cleaned every 3 4 weeks or whenever the grease filter indicator lights Always clean both the decor panel and the grease filter A dirty filter is a fire hazard Removing the decor cover dai0922 m To remove the decor cover pull on the release knobs Hold the decor cover when doing this so that it does not fall on to the cooktop m Remove the decor cover Removing the grease filter dai0924a m To remove the grease filter pull on the release knob Hold the grease filter when doing this so that it does not fall on to the cooktop 19 Cleaning and Care Cleaning the grease filters m By hand use a scrub brush with a solution of warm water and mild detergent Do not use the pure detergent aggessive all purpose cleaners oven sprays or limescale removers They could destroy the filters m In a dishwasher place the filters vertically in the lower basket making sure that the spray arm is not blocked Use a hot t
21. he grease filter The charcoal filter is designed to absorb cooking odors Replacement active charcoal filters can be ordered from the Miele Technical Service Department 1 800 999 1360 1 800 565 6435 m Ihe decor cover must be removed to access the active charcoal filter See Cleaning and Care 6r60lep m Before inserting an active charcoal filter for the first time remove the connector for use in air extraction mode Loosen the screw in the connector and remove dai0927a m To remove the active charcoal filter pull down on the tab at the back of the filter dai0927b m Insert the new charcoal filter on an angle toward the front of the hood and then firmly press the rear in place m Return the grease filter and decor cover m When the active charcoal filter is installed for the first time program the charcoal filter timer See Operation Reprogramming the charcoal filter timer 21 Cleaning and Care Replace the active charcoal filter when the charcoal filter indicator lights Replace the filter at least every 6 months or when it no longer absorbs odors efficiently The old charcoal filter can be disposed of in the household waste m After replacing the charcoal filters press and hold the charcoal filter button for about 3 seconds to reset the charcoal filter timer The indicator light will go out m If the charcoal filters are replaced
22. he installation m Read all instructions m Determine height S regarding the user s body height i e a comfortable height for the user However the greater the distance the less effectively cooking odors are drawn in m f the hood is fitted flush to the ceiling make sure that the remaining distance to the ceiling is not greater or less than appliance height H Standard unit height H Air Extraction us esas 28 3 4 3B lada ere 716 966 mm Recirculation 33 42 ie Hp pde aceon ee 836 1066 mm If the standard unit height H is not suitable to the kitchen s ceiling height longer optional chimney extensions are available from your Miele dealer or Miele 33 Installation Installation instructions m See the enclosed installation instruction sheet m Please read the Important Safety Instructions and Installation instructions before installing this hood Protective film The casing is covered with a protective film to prevent scratching during transport m Peel off the film before installing the casing parts 34 Dismantling If the hood needs to be disassembled follow the instructions on the installation sheet in the reverse order A lever is enclosed for easier removal of the chimney extension p dai0920 m After removing the screws from the chimney slide the lever between the chimney and the chimney extension and gently apply pressure to e
23. llel to the flow direction of the flue Never connect an exhaust hood to an active chimney dryer vent vent flue or room venting ductwork Seek professional advice before connecting an exhaust hood vent to an existing inactive chimney or vent flue Important If the ductwork runs through rooms ceilings garages etc where temperature variations exist it may need to be insulated to reduce condensation 36 Condensate trap optional accessory dai1585us In some cases a condensate trap may also be required to collect and evaporate any condensation which may occur This optional accessory is available for ducts 5 125 mm and 5 150 mm in diameter When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust outlet The arrow on the casing shows the venting direction 37 38 39 When contacting the Technical Service please quote the model and serial number of your appliance Miele Inc Miele Limited National Headquarters National Headquarters 9 Independence Way 55G East Beaver Creek Road Princeton NJ 08540 Richmond Hill ON L4B 1E5 Phone 800 843 7231 Phone 800 643 5381 609 419 9898 905 707 1171 Fax 609 419 4298 Fax 905 707 0177 www miele com www miele ca info miele ca general enquiries Technical Service amp Support professional miele ca commercial Nationwide enquiries Phone 800 999 1360 Fax
24. n Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards Repairs and other work by unqualified persons could be dangerous and the manufacturer will not be held responsible IMPORTANT SAFETY INSTRUCTIONS This equipment is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for installation in these applications Please contact the nearest Miele dealer or the Technical Service Department with specific requirements Before servicing or cleaning the unit switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally If the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Before discarding an old appliance unplug it from the power supply and remove the power cord and any doors to prevent hazards Use Do not allow children to play with or operate the appliance or its controls Supervise its use by the elderly or infirm Be careful when preparing a flamb beneath the hood Flames may be drawn up into the hood by the suction and the grease filters may catch fire Never operate gas burners without cookware Turn the burner off when not in use Adjust the burner so that the flame
25. n mode The timer for the charcoal filter is not preset Please program this timer see Operation Reprogramming the charcoal filter timer The charcoal filter indicator will light once the selected time has elapsed The charcoal filters must then be replaced and the charcoal filter timer must be reset m To do this press the charcoal filter button for about 3 seconds The indicator will go out Checking the filter timers To check the percentage of time already used LO oj m Press the On Off button to turn the fan on m Press the grease or charcoal filter button The number of flashing indicators show the percentage of programmed hours that have been used 0000 1 indicator less than 25 2 indicators less than 50 3 indicators less than 75 4 indicators less than 100 This information will remain stored in memory in the event of a power failure Operation Reprogramming the timers The grease filter timer is preset to 30 00 hours This time can be lengthened or shortened to 20 30 40 or 50 hours Atime of 20 hours should be programmed in kitchens with The indicator for the grease filter and one of the indicators will flash frequent pan or deep frying The lit indicator shows the programmed time A time of 20 hours should also be programmed if the kitchen is only 1st indicator from the left 20 hours used occasionally Otherwise gr
26. s do not extend beneath the cookware The hood can be damaged due to exessive heat from the burners Do not use the hood without the grease filters in place Clean the grease filters regularly Dirty filters are a fire hazard Do not use a steam cleaner to clean the hood Steam could penetrate the electrical components and cause a short circuit Always turn on the hood when using the cooktop to prevent damage from condensation IMPORTANT SAFETY INSTRUCTIONS N WARNING TO REDUCE THE RISK OF A COOKTOP GREASE FIRE Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers may ignite Heat oils slowly on low or medium settings Always turn the hood on when cooking at high heat or when cooking flaming foods Clean ventilation fans frequently Grease should not be allowed to accumulate on the fan or filter Use the proper pan size Always use cookware appropriate for the size of the surface element N WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A COOKTOP GREASE FIRE OBSERVE THE FOLLOWING SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT NEVER PICK UP A FLAMING PAN You may be burned DO NOT USE WATER including wet dishcloths or towels a violent steam explosion may result Use
Download Pdf Manuals
Related Search