Miele 38ACR User's Manual
Contents
1. Step 3 Refer to Figures 2 and 7 and slide the door bottom channel into position Secure by tightening screws previously loosened through the holes provided on the top face of the chan nel Install the door top channel over the middle screw and secure it in place with four screws two screws previously removed and two screws previously loosened Figure 7 Step 4 Starting with either the right or left door assembly Engage the hinge pin into the hole in the clip within the top door channel The roller pin must be positioned within the upper door guide track Figures 8 and 9 Roller Pin Figure 8 Upper Door Hinge Pin Guide Track a g Pi Roller Pin SA g gt Figure 9 Step 5 Lift and swing the lower corner of the door over the hole in the bottom door channel and engage the shorter hinge pin into this hole Figures 10 and 11 Bottom Door Channel Figure 10 AT Figure 11 Lower Hinge Pin Step 6 Repeat this procedure for the opposite door assembly ADJUSTMENT FOR DOOR ALIGNMENT The doors are properly adjusted when the top door trim is in a straight level line and the gap between the doors is even at the top and bottom If adjustments are required grasp the door handle and loosen the lower door hinge pin using a 3 8 open end wrench Slide the door panel on the hinge pin until the gap between the upper door tr2. into the bottom channel Note The pins on the glass end panel require repositioning when the door is fitted into an opposing right or left hand opening To shift the pins loosen the pins using a 3 8 open end wrench and slide the pins as required along the frame channel Position the door squarely within the opening equally gapped at the right and left sides and secure the pins in place by tightening with the wrench Al lt D Outside mi End Panel Top Channel Screw 2 Places Corner Post 7 End Panel Bottom Channel Figure 4 BI FOLD DOOR INSTALLATION STEPS Step 1 Attach the polished metal and wooden handle assemblies to the lower door frames Figure 5 Use the No 8 32 x 1 4 Philips pan head screws and associated nuts provided in the hardware kit There is a single screw and nut for use with each handle assembly Slide the nuts into the frame channel and insert the screws through the handle brackets and then into the nuts Position the handle assemblies approximately as shown on the front page of this document and tighten the screws to secure the handles in place Figure 5 CAUTION DO NOT OVER TIGHTEN HANDLE SCREWS Step 2 Install two 2 baffles one above the other with the black No 8 15 x 1 2 Phillips pan head screws from the hardware kit Figure 6 NOTE DIAGRAMS amp ILLUSTRATIONS NOT TO SCALE I 1 N y amp Ai f T n jl T IOOGMOO Figure 6
3. 1 Remove the screen rod covers from the front and corner openings Remove two angle retainers and replace screws Note Units are shipped without covers installed Step 2 Refer to Figure 2 and remove the top two outer screws and loosen the bottom screws at least two 2 turns Remove corner shipping post if installed CAUTION REMOVE THE PLASTIC PROTECTIVE COATING FROM ALL BRASS PIECES BEFORE INSTALLATION Tested amp Beaverton Listed By Oregon USA c US OMNI Test Laboratories Inc NOTE DIAGRAMS amp ILLUSTRATIONS NOT TO SCALE TOOLS REQUIRED e Phillips screwdriver small or medium Loosen At Least Two 2 Turns Do Not Touch Loosen At Least Two 2 Turns Remove And Retain Remove And Retain Remove Shipping Corner Post Loosen All Lower Screws At Least Two 2 Turns Figure 2 Step 3 Slide the end panel bottom channel into position and tighten the end screws that were previously loosened Install the top track over the middle screw and secure with the screws removed and retained in Step 2 Figure 3 Step 4 Refer to Figures 3 and 4 and install the corner post to the ends of the end panel top and bottom channels Secure it in place with two screws from the hardware kit Step 5 Insert the upper pins of the end panel assembly into the holes in the top channel Swing the bottom portion of the end panel over the bottom channel and insert the lower pins
4. CLEAN THE GLASS OR THEDOOR FRAME AN AMMONIABASED CLEANER WILL DAMAGE THE FINISH Remove dirt and grime from the doors using a clean dampened towel followed by wiping with a dry towel To remove stubborn stains from the doors useamild soap solution and towel to gently scrub away stain Takecarenotto scratch the glass surface Do not use abrasive cleaners IMPORTANT These glass doors utilize tempered glass which is designed for use with high tempera tures but can unexpectedly shatter DO NOT SIT CLOSE TO THE GLASS Tempered glass will break into small particles if it should shatter unexpectedly If the glass breaks particles of extremely hot glass could be discharged into the surrounding environ ment thereby creating arisk of personal injury or fire Observation of the above operating precautions and instructions will reduce the risk of personal injury or fire Extreme temperature changes can cause break age do not build a hot fire and close the doors if the doors are cold If the tempered glass pane becomes scratched or chipped it creates a weakness in the glass which can causethe glass to break when heated Replace the pane of glass by contacting your nearest LHP Distributor For the name of your nearest distributor contact LENNOX HEARTH PRODUCTS 1110 West Taft Avenue Orange CA 92865 WARNING DO NOT BURN TRASH CONSTRUCTION SCRAPS RAILROAD TIES OR OTHER HIGHLY FLAM MABLE MATERIAL IN THE FIRE PLACE INT
5. ENSE HEAT CAN CAUSE THEGLASS TO LOSESTRENGTH AND RESILIENCE WHICH WILL RESULTIN GLASS BREAKAGE The manufacturer reserves the right to make changes at any time without notice in design materials specifications prices and also to discontinue colors styles and products Consult your local distributor for fireplace code information Printed in U S A 1999 by LENNOX HEARTH PRODUCTS HEARTH PRODUCTS P N 904665 REV C 03 2008 1110 West Taft Avenue Orange CA 92865
6. LENNOX HEARTH PRODUCTS FIREPLACE KITS AND ACCESSORIES 904665 REV C 03 2008 GLASS DOOR END PANEL INSTALLATION INSTRUCTIONS FOR ABF GLASS DOOR END PANEL PACKAGED SET MODELS 38ACR AND 38ACR BB Lennox s Glass Door End Panel Packaged Set Models 38ACR and 38ACR BB are designed to be installed on the CR 3835R L Series fireplaces These kits come complete with all of the required hardware necessary to complete the task Please read and understand these instructions carefully before begin ning installation and operation Do not attempt to alter or modify the construction of these glass door assemblies as it could cause amalfunc tion or possible fire hazard The Models 38ACR and 38ACR BB have been tested and listed by Omni Test Laboratories Inc PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE GENERAL INFORMATION Before starting the installation of the glass doors and end panel assure the kit is complete and undamaged Refer to Figure 7 and the inventory list to identify all necessary parts INVENTORY LIST Top Channel door Bottom Channel door A 1 1 Glass End Panel B 1 C 1 Top Channel panel D 1 E Door Panel Assembly LH Door Panel Assembly RH 2 Baffles Hardware Kit Including andles Installation Instructions Bottom Channel panel 1 Corner Post IARSIN Figure 1 END PANEL INSTALLATION STEPS Step
7. im and upper frame is even Retighten the lower door hinge pin Repeat this procedure for the opposite door if needed Note Upper door hinge pins can also be loosened for adjustment purposes however it is easier to loosen lower pins GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS CAUTION THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH THE SUPE RIOR FIREPLACE OR APPLIANCE MODELS SHOWN USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A PO TENTIAL FIRE HAZARD e Avoid building extremely large fires as the tempered glass could become damaged Use fireplace tools carefully to avoid striking the glass Keep wire mesh screens closed during fire place use The fireplace flue damper must remain open until fire is completely out Assure wood and embers are well within the confines of the grate area and well away from the glass doors Keep glass doors closed at night when retir ing to minimize the loss of heated room air up the vent CAUTION THE CORNER FIREPLACE OR AP PLIANCE SHOULD ONLY BE OPERATED WITH THE BI FOLD GLASS DOORS FULLY OPEN OR FULLY CLOSED FIGURE 12 End Panel CI CJ Fully Open or Fully Closed Figure 12 CAUTION GLASS AND METAL FRAMES GET HOT ALWAYS USE HANDLES TO OPEN AND CLOSE THE DOORS NOTE DIAGRAMS amp ILLUSTRATIONS NOT TO SCALE CLEANING NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT DO NOT USE AMMONIA OR ANY AMMONIA BASED GLASS OR HOUSEHOLD CLEANER TO
Download Pdf Manuals
Related Search