Metra Electronics LEXUS ES 95-8150 User's Manual
Contents
1. AL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black OU 2 sac Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 3 SE m NOTES SE m NOTES 95 8150 INSTRUCTIONS re 1 800 221 0932 www metraonline com REV 11 09 07 COPYRIGHT 2004 2007 METRA ELECTRONICS CORPORATION INST95 81502. INSTALLATION INSTRUCTIONS FOR PART 95 8150 APPLICATIONS LEXUS ES SERIES 1992 1996 95 8150 KIT FEATURES IOo ee e Double DIN Radio Provision wnn e Stacked ISO Mount Units Provision TE nr KIT COMPONENTS Double Din Trim Plate TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver 9 Socket Set gt A 1 800 221 0932 www metraonline com COPYRIGHT 2004 2007 METRA ELECTRONICS CORPORATION fa IET ON TABLE OF CONTENTS Dash Disassembly Lexus ES Series 1992 1996 os aaea aaa 1 Kit Assembly Double DIN Radio Provision ss s s s s s s s s c s c s s s s c s g s g aa 2 Stacked ISO Mount Units Provision 2 FINALASSEMDU xxinavzzzjontakanjsrari ER R RR ranr riri kii 3 Note Refer also to the instructions included with the aftermarket radio zh i i Tue 95 8150 DASH DISASSEMBLY LEXUS ES SERIES 1992 1996 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unclip and remove the plastic trim piece below the factory radio and remove 2 Phillips screws exposed underneath Figure A 3 Using a small flat blade screwdriver release the clips securing the a c vent assembly and remove the assembly Figure B 4 Remove 2 Phillips screws inside of vent cavity Figure B 5 Pull the climate control radio assem bly from the dash and disconnect th
3. e wiring Figure C 6 Remove 2 Phillips screws and 4 bolts per side to remove factory brackets from climate controls and radio Retain the factory brackets climate controls and screws to be re installed during kit assembly Continue to kit assembly EA A Me 95 8150 KIT ASSEMBLY LEXUS ES SERIES 1992 1996 DOUBLE DIN RADIO STACKED ISO MOUNT UNITS PROVISON Note Refer also to the instructions included with the aftermarket radio 1 Assemble the climate controls and Double DIN or stacked ISO mount units into the factory brackets using the hardware from disassembly and the screws supplied with the Double DIN or stacked ISO mount units Figure A 2 Before tightening the top 2 mounting screws to the Double DIN or stacked ISO mount units attach the Double DIN trim plate and secure with the top 2 mounting screws Figure B Continue to final assembly P MESA 935 8150 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends hack 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FIN
Download Pdf Manuals
Related Search