Metra Electronics KIA OPTIMA 99-7324 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 99 7324 APPLICATIONS KIA Optima 2006 5 2010 99 7324 KIT FEATURES e DIN head unit provision with pocket e ISO DIN head unit provision with pocket KIT COMPONENTS A Radio Housing B ISO Brackets C Trim Plate lt WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1004 Hyundai 2006 up KIA harness 2004 up e 70 7303 Hyundai KIA Harness 2009 Antenna Adapter e 40 KI11 2009 10 Kia Optima TOOLS REQUIRED Phillips Screwdriver e Small Flat Blade Screwdriver Panel Removal Tool A 1 800 221 0932 www metraonline com COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION 707 99 7324 TABLE OF CONTENTS Dash Disassembly Kia Optima 2006 5 2010 sos nun nun nn 1 Kit Assembly Din Head Unit provision with Pocket 2 SO Din Head Unit provision with Pocket 3 Final ASSEMDIV ss sec sen transat ecuseseuirsss is 4 Note Refer also to the instructions included with the aftermarket radio RAPAE EIGE i PORWER SE HET CRRA CCI HEA Sert ces Seah dent ETES Bas eng ie e Re Ro ne AA E ner eT E Les ee gone afin ET Pb weed ARE evince interne al er po macia De Ihe Mers A 29 7324 DASH DISASSEMBLY KIA OPTIMA 2006 5 2010 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unclip and remove the panel sur rounding the r2. adio including the a c vents and climate controls Figure A 3 Remove 4 Phillips screws securing radio Unplug and remove radio Figure B Continue to kit assembly Y mens 99 7324 KIT ASSEMBLY DIN HEAD UNIT PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward Figure A 2 Slide the aftermarket radio into the cage until it snaps into place Figure B Continue to final assembly LES 99 7324 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Mount the ISO Brackets to the radio using the screws supplied with the radio Figure A 2 Slide the radio into the radio open ing until the side clips snap into place Figure B 3 Snap the trim plate onto the front of the Radio Housing Figure B Continue to final assembly RIGHT SIDE CLIP LS 22 7324 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends hack 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for prope
3. r operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black IIlumination Orange Left Rear Green DIMM een Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 4 m 27 99 7304 NOTES 99 7324 INSTRUCTIONS ee o_o 1 800 221 0932 www metraonline com REV 04 27 10 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INST99 7324
Download Pdf Manuals
Related Search