Metra Electronics 99-8715 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 99 8715 APPLICATIONS SMART FORTWO 2008 10 99 8715 KIT FEATURES e DIN Radio Provision With Pocket e ISO Mount Radio Provision With Pocket e Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS e A Radio Housing B Trim Plate C ISO Brackets D Double DIN Trim Plat e E Double DIN Brackets e F Pocket Harness amp Antenna Connections sold separately e 70 1783 Smart Car Harness e 40 VW10 VW Antenna Adapter TOOLS REQUIRED e Phillips Screwdriver Panel Removal Tool e T 20 Torx Screwdriver BR a 1 800 221 0932 m www metraonline com COPYRIGHT 2010 METRA ELECTRONICS CORPORATION SRE TABLE OF CONTENTS Dash Disassembly Smart Fortwo 2008 10 ms sosummmummmummnuunnnsl Kit Assembly DIN Radio Provision with Pocket 2 S0 Mount Radio Provision with Pocket 3 Double DIN Stacked ISO Mount Units Provision 4 FINAL ASSPIIDIV iiid ka p FEX CER ERE EFRREA RrEkRriui skrbrbrrid Note Refer also to the instructions included with the aftermarket radio etalk KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto ww w installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomor row Y Men2. a SA 99 8715 DASH DISASSEMBLY SMART FORTWO 2008 10 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Unclip the Hazard button switch panel Figure A 3 Remove 1 T 20 Torx head screw E zd Figure B T TET 4 Carefully unclip the panel surrounding the radio start at the top of the dash and work your way down Figure C 5 Remove 4 T 20 Torx head screws from around the radio Figure D 6 Remove radio and disconnect the wire harness and antenna Continue to kit assembly rM Mers 99 8715 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward Figure A 2 Slide the aftermarket radio into the cage until it snaps into place Figure B 3 Snap the pocket into the radio hous ing Figure C Continue to final assembly IE LES 99 8715 KIT ASSEMBLY 150 MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Mount the ISO Brackets to the after market radio using the screws sup plied with the radio Figure A 2 Slide the radio bracket assembly into the radio housing until it snaps into place Figure B 3 Snap the pocket into the radio hous ing Figure C 4 Snap the Trim plate onto the front o
3. er Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition ACC Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground 22 rr Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 99 8715 INSTRUCTIONS S D G 1 800 221 0932 m www metraonline com REV 04 23 10 COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99 8715
4. f the radio housing Figure D B Continue to final assembly y Mena sA 99 8715 KIT ASSEMBLY DOUBLE DIN STACKED I50 MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove the center bar from the radio housing Figure A 2 Snap the Double DIN brackets to the inside edge of the radio housing Figure B 3 Slide the Double DIN or stacked ISO mount unit s into the bracket radio housing assembly and secure the unit s to the assembly using the screws supplied with the unit s Figure C 4 Snap the Double DIN trim plate onto the front of the radio housing Figure C Continue to final assembly Oe A 39 8715 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Sold
Download Pdf Manuals
Related Search