Memorex MX4111 User's Manual
Contents
1. more details Aux Out REMOTE SENSOR To operate the unit with the remote control point the remote at the remote sensor on the front of the main unit and press the appropriate button The remote control has an effective operating range of approximately 15 feet and an angle of no more than 30 NOTE Bright sunlight may interfere with the operation of the remote control 3 MX4111 0 M QXD 7 11 02 4 06 Page 4 LOCATION OF CONTROLS FRONT 1 234 5 6 7 8 9 10 11 12 13 14 15 REAR 16 17 18 19 20 1 POWER ON STANDBY Button 12 TIMER SLEEP Button 2 PHONES Headphones Jack 13 FUNCTION Button 3 STANDBY Indicator 14 MASTER VOLUME Control 4 Remote Sensor 15 OPEN CLOSE Button 5 TUNING SKIP Search lt Buttons 16 Speaker Terminals 6 Display 17 FM STEREO MONO Switch 7 PLAY PAUSE Button 18 AUX IN Jacks 8 Button 19 FM Antenna Wire 9 CD Compartment 20 AC Cord 10 PRESET EQ Button 11 MEMORY TIME SET Button MX4111 0 M QXD 7 11 02 4 06 PM Page 5 LOCATION OF CONTROLS CONTINUED REMOTE 0 Direct Track Selection Buttons PLAY PAUSE 11 Button TUNING SKIP Search 1 lt Buttons STOP BAND Button FUNCTION Button REPEAT PRESET UP Button RANDOM Button DISPLAY Button TIMER Button POWER Button MUTE Button PRESET EQ Button PROGRAM CLK SET Button VOLUME Buttons SLEEP Butt2. TUNING SKIP Search gt or 4 button until the frequency the display starts to scan and then release the button the tuner will search and then stop on the next strong station it finds Repeat this procedure until the desired frequency appears in the display Hints for Better Reception FM Make sure that the FM Antenna Wire is extended to its full length You may have to vary the direction of the antenna to find the strongest signal for each FM station The AM ferrite bar antenna is located inside the unit It may be necessary to turn the unit slightly so that the internal antenna is pointing in the direction of the AM transmitter You may have to experiment to find the position that provides the strongest reception for each of your favorite AM stations MUTE To temporarily mute the sound press the MUTE button on the remote control the Mute indicator will appear in the display and the sound will be muted Press the MUTE button again to restore the sound and the Mute indicator will disappear from the display MX4111 0 M QXD 7 11 02 4 06 8 OPERATING INSTRUCTIONS CONTINUED SETTING RADIO PRESETS This unit can preset 10 AM and 10 FM radio stations for convenient recall Press the POWER ON STANDBY button to turn the unit on the STANDBY indicator will go out Press the FUNCTION button until TUNER appears
3. an outlet on a circuit different from that to which the receiver is connected Consult the dealer an experienced radio TV technician for help LASER SAFETY This unit employs a laser Only qualified service personnel should attempt to service this device due to possible eye injury CAUTION USE OF CONTROLS ADJUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE WARNING DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE FCC WARNING This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made PREPARATION FOR USE AC Operation Unwind the AC power cord and extend it to its full length Insert the end of the AC power cord into any convenient 120V 60Hz household outlet Please note that this unit is equipped with a polarized AC plug which has one blade wider than the other This is a safety feature to reduce the likelihood of electric shock This polarized AC plug will only fit in a polarized AC outlet If you AC Outlet find that you cannot insert this plug into your outlet you may have an obsolete non polarized outlet Please do not try to defeat this safety feature by using a non polarized adapter or by fili
4. in the display Press the STOP BAND button to select AM or FM Press the TUNING SKIP Search gt 44 button to select station Aw Aw 6 3 5 Press the SET button PROGRAM CLK SET on remote MEMORY will blink in the display Within 6 seconds press the REPEAT PRESET UP button on the remote until the desired memory number appears on the display Press the PROGRAM CLK SET button again to set the station in the selected memory Repeat steps 3 through 5 to program up to 10 stations in each band if desired In case the main power supply is interrupted the memory presets will be erased RECALLING RADIO PRESETS 1 2 Follow steps 1 2 above Press the REPEAT PRESET UP button to select a preset the station will automatically be tuned in Adjust the PRESET EQ button and MASTER VOLUME control as desired MX4111 0 M QXD 7 11 02 4 06 9 OPERATING INSTRUCTIONS CONTINUED PLAYING COMPACT DISCS NORMAL PLAYBACK Press the POWER ON STANDBY button to turn the unit on the STANDBY indicator will go out Press the FUNCTION button until CD appears in the display Press the OPEN CLOSE button and insert a CD with the label side facing up NOTE 3 inch single or standard CDs can b
5. until timer hour digits blink in the display With the power off press and Press the TUNING SKIP Search gt or 44 button to set the hour then press the MEMORY TIME SET button again the minute digits will blink Press the TUNING SKIP Search or kaa button to set the minutes then press the MEMORY TIME SET button again Within a few seconds will light in the display to indicate that the timer is set When the actual time matches the time set for the Timer the unit will turn on to the last function CD or tuner used TO TURN THE TIMER OFF SO IT IS NOT SET FOR THE NEXT DAY press and hold the TIMER SLEEP button again until TIMER disappears from the display The unit will revert back to standby mode one hour after the timer has been activated ACTIVATING THE SLEEP FUNCTION Set the sleep timer as follows Press the POWER ON STANDBY button to turn the unit on and tune the desired radio station or insert a CD as previously instructed Press the TIMER SLEEP button and 90 will appear and SLEEP will blink in the display Press the TIMER SLEEP button a second time to set the unit to turn off after 80 minutes Each additional press with decrease the sleep time by 10 minutes After the sleep time is set you can press the TIMER SLEEP button at any time to stop the Sleep function SLEEP will di
6. 1 02 TROUBLESHOOTING 4 06 Page 15 Should this unit exhibit problem check the following before seeking service Symptom Radio Possible Cause Solution Noise or sound distorted on radio broadcasts FM STEREO indicator does not light Station not tuned properly for AM or FM Retune the AM or FM broadcast station FM Antenna Wire is not extended Extend FM Antenna Wire AM Unit is not positioned correctly Poor FM signal being received Rotate unit until best reception is obtained Retune station or try another station that broadcasts in stereo STEREO MONO switch is not in the STEREO position Slide the STEREO MONO switch to the STEREO position Station is not broadcasting in stereo Change stations AM or FM no sound Compact Disc Player TUNER is not selected Press the FUNCTION button to select Tuner Volume at minimum Increase volume CD Player will not play CD function is not selected Press the FUNCTION button to select CD CD is not installed or installed incorrectly Insert CD with label facing up CD skips while playing Disc is dirty or scratched Wipe disc with cloth or use another disc General No power AC power cord is not connected Connect AC power cord Remote not working Batteries not inserted or inserted correctly Insert batteries correctl
7. DOM disappears from the display 10 MX4111 0 M QXD 7 11 02 4 06 11 OPERATING INSTRUCTIONS CONTINUED REPEAT PLAYBACK To repeat a single track press the REPEAT PRESET UP button once REPEAT will blink in the display Press the TUNING SKIP Search K lt button to select the specific track that you wish to repeat When the desired track number appears in the display press the PLAY PAUSE gt button to begin playback The specific track you selected will be repeated continuously To repeat all of the tracks on a disc continuously press the REPEAT PRESET UP button twice REPEAT will light solid in the display Press the CD PLAY PAUSE PII button to begin all tracks repeating To cancel Repeat Playback press the REPEAT PRESET UP button until REPEAT disappears from the display PROGRAMMED PLAYBACK The CD player in this unit has a 20 track programmable memory that allows you to program up to 20 tracks on any disc for playback in any desired order You may program 20 different tracks or you may also program certain tracks to play more than once To perform programmed playback proceed as follows Press the STOP BAND button to select CD Press the OPEN CLOSE button and insert a CD with the label side facing up Press the MEMORY T
8. IME SET button P 01 program number 01 track number will appear and MEMORY will blink in the display PROGRAMMED PLAYBACK SECTION CONTINUED ON NEXT PAGE 11 MX4111 0 M QXD 7 11 02 4 06 12 OPERATING INSTRUCTIONS CONTINUED Press the TUNING SKIP Search gt or 144 button to select the first track that you wish to program When the desired track number appears in the display press the MEMORY TIME SET button again Press either the TUNING SKIP Search gt gt I K lt button to select the next track you wish to Repeat step 5 until you have programmed up to 20 track numbers into the CD Program program When the desired track Memory number appears in the display press the MEMORY TIME SET button again After programming up to 20 tracks in the CD Program Memory press the PLAY PAUSE gt Il button to begin programmed playback MEMORY will appear in the display and playback will begin on the first track that you programmed The player will continue to play all of the tracks that you programmed in the order in which you programmed them When the last programmed track has been played the player will stop and the display will again show the total number of tracks on the disc If you press the MEMORY TIME SET button and then press th
9. X4111 0 M QXD 7 11 02 4 06 Page 18 2 Memorex HOME AUDIO SYSTEM WITH CD PLAYER AND AM FM STEREO RADIO MODEL MX4111 BEFORE OPERATING THIS PRODUCT PLEASE READ THESE INSTRUCTIONS COMPLETELY OPERATING INSTRUCTIONS MX4111 0 M QXD 7 11 02 4 06 Page 1 2 WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE THIS PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with CAUTION TO REDUCE THE The exclamation point within arrowhead symbol within an RISK OF ELECTRIC SHOCK DO an equilateral triangle is equilateral triangle is intended NOT REMOVE COVER OR intended to alert the user to the to alert the user to the BACK NO USER SERVICEABLE presence of important presence of uninsulated PARTS INSIDE REFER SERVIC operating and maintenance dangerous voltage within the ING TO QUALIFIED SERVICE servicing instructions in the product s enclosure that may PERSONNEL literature accompanying the be of sufficient magnitude to appliance constitute a risk of electric shock to persons DANGER Invisible and hazardous laser radiation when open and interlock failed or defeated Avoid direct exposure to beam Read these instructions Keep these instructions Heed all warn
10. e PLAY PAUSE II button again playback will start on the first track you programmed and will continue until all the programmed tracks have been played To cancel the Programmed Playback mode press the MEMORY TIME SET button to enter the program mode and then press the STOP BAND button twice PROGRAMMED REPEAT It is also possible to use the Program and Repeat functions together to repeat a specific program indefinitely First enter the Repeat mode and then program the tracks you wish to hear in the order you wish to hear them as described above Both the MEMORY and REPEAT indicators will appear in the display Press the PLAY PAUSE button to begin programmed repeat playback The player will play the tracks you selected in the order in which you programmed them When the last track in the program has been played the entire program will begin again 12 Program Repeat operation will continue indefinitely until you press the STOP BAND button MX4111 0 M QXD 7 11 02 4 06 SETTING THE TIMER Page 13 OPERATING INSTRUCTIONS CONTINUED Set the timer to turn the unit on to the Tuner or CD mode at a preset time as follows e LO hold the TIMER SLEEP button TIMER on the remote until TIMER blinks in the display Press and hold the MEMORY TIME SET button
11. e used with this unit The CD player will read the table of contents on the disc and the total number of tracks and total playing time on the disc will appear in the display Press the PLAY PAUSE button to begin playback on Track 1 Adjust the PRESET EQ button and MASTER VOLUME control as desired Playback will continue until all the tracks on the disc have been played To stop playback before the disc ends press the STOP BAND button The disc will stop and the display will show the total number of tracks and playing time on the disc CD PAUSE CONTROL During CD playback if you wish to pause the disc momentarily press the PLAY PAUSE PII button again Playback stops but the disc continues to spin and the time display will blink Press the PLAY PAUSE PII button again to release pause and resume normal CD playback 9 MX4111 0 M QXD 7 11 02 4 06 10 OPERATING INSTRUCTIONS CONTINUED TO BEGIN PLAYBACK FROM A SPECIFIC TRACK After you insert the disc into the CD player and the total number of tracks appear on the display you may press either the TUNING SKIP Search 2 or 44 button to select a specific track for playback You can also use the Direct Track Selection buttons on the remote to directly select a track If
12. he display To listen to the unit through headphones simply insert the headphones not included into the Headphones jack The speakers will be disconnected when the Headphones are plugged in MX4111 0 M QXD 7 11 02 4 06 7 OPERATING INSTRUCTIONS CONTINUED LISTENING TO THE RADIO Press the POWER ON STANDBY button to turn the unit on the STANDBY indicator will go out Press the FUNCTION button until appears the display Press the STOP BAND button to select AM or FM NOTE If you select the FM band be sure to extend the FM Antenna Wire If listening to FM slide the FM STEREO MONO switch on the rear of the unit to the desired position Noise present in FM stereo broadcasts can be reduced by listening in Mono TUNING Press the TUNING SKIP Search gt or 44 button to select a station see Tuning note below NOTE If the FM STEREO band is selected and you have tuned to an FM Stereo station the FM Stereo indicator will light in the display Adjust the PRESET EQ button and MASTER VOLUME control as desired MANUAL TUNING Repeatedly press the TUNING SKIP Search 1 or 44 button to manually advance the frequency in the display up or down until the desired frequency appears AUTOMATIC TUNING Press and hold the
13. hing water and no object filled with liquids such as vases shall be placed on the apparatus 15 Do not overload wall outlet Use only power source as indicated 16 Use replacement parts as specified by the manufacturer 17 The product may be mounted to a wall only if recommended by the manufacturer 18 Upon completion of any service or repairs to this product ask the service technician to perform safety checks en MX4111 0 M QXD 7 11 02 4 06 Page 2 SAFETY INSTRUCTIONS INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into
14. ings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Unplug this apparatus during lightning storms or when unused for long periods of time 13 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally has changed its performance or has been dropped 14 This appliance shall not be exposed to dripping or splas
15. ng the wider blade to make it fit into your outlet If this plug does not fit into your outlet you should contact a qualified licensed electrician to replace your obsolete outlet AC Plug MX4111 0 M QXD 7 11 02 4 06 Page 3 2 PREPARATION FOR USE CONTINUED SPEAKER CONNECTION 1 4 connect the speakers press the terminal down insert the speaker wire and Locate the Speaker Terminals on the rear of the unit and connect the solid red wires Place the speakers in convenient locations on either side of the unit Usually a feo distance of five to eight feet between speakers provides the best stereo effect but this may vary depending on the size and acoustics of the room to the red terminals and connect the black wires to the black terminals press the terminal back to the lock position Pull lightly on the connection to make sure it is secure CAUTION Only connect the speakers which are supplied with the unit The use of any other or additional speakers may cause damage to the unit Never operate the unit without the speakers connected BATTERY OPERATION The battery compartment is located on the rear of the remote control Remove the battery compartment door by pressing down and sliding the door in the direction of the arrow Insert two 2 AAA size batteries into the battery compartment as shown to the right Be sure t
16. o observe the polarity markings which are engraved inside the battery compartment If the batteries are inserted incorrectly the remote control will not operate Replace the battery compartment door Follow these precautions when using batteries in this device 1 2 3 4 5 BATTERY PRECAUTIONS Use only the size and type of batteries specified alkaline are recommended Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible battery leakage Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions CONNECTING AN EXTERNAL UNIT TO THE AUX IN JACKS You can connect an external unit to the MX4111 such as a cassette player etc Simply connect a audio video cable not included from the AUX IN jacks of this 4111 to the external unit s AUX OUT jacks This will allow you to broadcast the external unit s sound through this unit Press the FUNCTION button to select AUX to use the external unit NOTE Please refer to the external units owner s manual for
17. on Battery Compartment Rear of Remote OP Oe OT Fe Oe I Ce Ce O MX4111 0 M QXD 7 11 02 4 06 6 OPERATING INSTRUCTIONS SETTING THE CLOCK With the power off press and hold the MEMORY TIME SET button PROGRAM CLK SET on the remote 24H will blink Press the TUNING SKIP Search gt or 4 button to set the unit to the 24 hour 24H mode also known as military time or 12 hour 12H mode Press the MEMORY TIME SET button and the hours will blink Press the TUNING SKIP Search gt or 44 button to set the current hour then press the MEMORY TIME SET button again the minute digits will blink Press the TUNING SKIP Search gt 44 button to set the current minute the MEMORY TIME SET button and the time will be set AUX Press the FUNCTION button to select AUX to listen to the external unit See page 3 to connect an external unit PRESET EQ DISPLAY BUTTON HEADPHONE JACK 4 Press the PRESET EQ button to cycle through the preset EQ settings or to turn the EQ off Each press of the PRESET EQ button will cycle as follows CLASSIC ROCK POP Off Press the DISPLAY button on the remote once to show the clock on the display Press again to show the timer on t
18. sappear from the display 13 MX4111 0 M QXD 7 11 02 4 06 PM Page 14 AND MAINTENANCE Caring for Compact Discs 2 Treat the compact disc carefully Handle the compact disc only by its edges Never allow your fingers to come in contact with the shiny unprinted side of the compact disc J Do not attach adhesive tape stickers etc to the compact disc label Clean the compact disc periodically with a soft lint free dry cloth Never use detergents or abrasive cleaners to clean the compact disc If necessary use a CD cleaning kit compact disc skips gets stuck a section of the compact disc it is probably dirty or damaged scratched When cleaning the compact disc wipe in straight lines from the center of the compact disc to the outer edge of the compact disc Never wipe in circular motions This unit is designed to play only compact discs bearing the identification logo as shown here _ Other compact discs may not conform to the CD standard and may not play properly d Compact discs should be stored in their cases after each use to avoid damage S A OENE Do not expose compact discs to direct sunlight high humidity high temperatures or dust etc Prolonged exposure or extreme temperatures can warp the compact disc Do not stick or write anything on either side of the compact disc Sharp writing instruments or the ink may damage the surface MX4111 0 M QXD 7 1
19. the track is over 10 press the gt 10 button first When the desired track number appears in the display press the PLAY PAUSE button Playback will begin on the track you selected FORWARD REVERSE SKIP TRACK AND HIGH SPEED MUSIC SEARCH gt gt 1 lt lt During playback press the TUNING SKIP Search button once to advance the player to the beginning of the next track Press the TUNING SKIP Search button repeatedly to advance the player to higher numbered tracks During playback press the TUNING SKIP Search i button once to move the player back to the beginning of the current track Press the TUNING SKIP Search 4 button repeatedly to move the player back to lower numbered tracks During playback depress and hold either the TUNING SKIP Search 4 button to move the player forward or backward within a track to locate a specific musical passage The player will move forward or backward at high speed as long as the button is depressed When you release the TUNING SKIP Search 4 button normal playback will resume RANDOM PLAYBACK Aw To play the tracks on the CD ina random order press the RANDOM button on the remote RANDOM will appear in the display and the tracks will play in a random order To cancel random playback press the RANDOM button until RAN
20. y 15 MX4111 0 M QXD 7 11 02 4 06 PM Page 16 2 FOR ADDITIONAL SET UP OR OPERATING ASSISTANCE PLEASE VISIT OUR WEBSITE WWW MEMCORPINC COM OR CONTACT CUSTOMER SERVICE AT 1 800 919 3647 PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX FOR PARTS AND ACCESSORIES CONTACT FOX INT L AT 1 800 321 6993 16 MX4111 0 M QXD 7 11 02 4 06 PM Page 17 2 Inc Weston FL Printed in Hong Kong Visit our website at www memcorpinc com
Download Pdf Manuals
Related Search