Mellerware TRENTO 1200W User's Manual
Contents
1. Attach the filter holder on correctly and turn it all the way e Clean the holes in the spouts e Fit in the plastic ring properly The espresso coffee is cold e The OK pilot light was not on when the coffee delivery switch was pressed The preheating was not carried out e The cups were not preheated e Wait until the OK pilot light comes on e Carry out the preheating as indicated in the Preheating the coffee unit section e Preheat the cups by rinsing them in hot water The pump is too noisy The coffee has an acidic taste e The water tank is empty The tank is inserted wrongly and the valve at the bottom is not open The unit was not sufficiently rinsed after the descalling process procedure e Fill the tank e Press the tank lightly so as to open the valve at the bottom Rinse the unit as described in the descaling section The coffee cream is light coloured the coffee comes out quickly from the spout e The ground coffee has not been tampered enough The quantity of ground coffee is not enough e The coffee is not ground finely enough e Tamper the ground coffee down more ncrease the quantity of coffee e Only use coffee specifically ground The coffee cream is dark the coffee comes out slowly from the spout e The ground coffee is too tightly pressed The quantity of ground coffee is too much The espresso boiler outlet is blocked e The coffe2. During the brewing process do not remove the filter holder from the coffer maker When pressing the reducer paddle on the handle the excess pressure in the filter holder will be released to revert accidental pressure release HOW TO BOIL HOT WATER 1 Mount the filter together with the empty filter holder or without a filter holder to the coffee unit as described above 2 Turn the switch to the Heater position V Wait until the Ok light CO is lit 3 Put the cup under the two outlets of the filter to hold the hot water 4 When the Ok light ge is lit turn the switch to the Brew position when hot water will flow into the cup nonstop through the outlets of the filter till the Ok light is off then turn the switch back to the Heater position If you need more hot water repeat the above steps when the Ok light is lit again 5 Turn the switch to the OFF position Unplug the unit from the mains NOTE Do not operate the appliance without water in the tank and always remember to fill the tank when the water level goes below the MIN level Do not fill exceeding the MAX level on the water tank HOW TO PREPARE FROTHY MILK FOR CAPPUCCINO 1 Prepare Espresso following the above mentioned procedures Prepare a cup and adequate milk NOTE chill the milk in refrigerator before use Do not use hot milk 2 Turn the selector switch to Steam mode A and wait until the Ok light is on This machine will then automatically
3. detect the required temperature The Ok light will be on when temperature reaches appropriate level NOTE Make sure the steam nozzle is closed when turning the selector switch to Steam mode 3 Pour adequate cold milk into the cup 4 Place the cup under the steam nozzle and make sure to bathe the end of steam nozzle into the milk completely 5 Turn the steam release knob anticlockwise release the steam to make a layer of foam on the milk NOTE When the steam release knob is turned to MAX it can not go further but backwards Do not force to turn the knob to avoid danger or injury caused by the flow of hot steam 6 When adequate foam is made turn the steam release knob clockwise and turn off the power of the machine 7 Pour adequate hot milk into coffee a cup of hot coffee with milk is done 8 Unplug the machine from the socket 9 Let the machine to cool down then hold the joint of steam nozzle with one hand and detach the whole nozzle set with another rinse the set then assemble back into the unit BREWING CAPPUCCINO 1 Prepare Espresso coffee using large cups for Cappuccino see HOW TO PREPARE ESPRESSO COFFEE paragraph 2 Pour the frothed milk into the cups containing the Espresso coffee see HOW TO PREPARE HOT MILK FOR CAPPUCCINO paragraph 3 Add sugar to taste and if desired sprinkle a little powdered chocolate on top of the froth CLEANING AND MAINTENANCE CLEANING THE ES
4. filter holder is firmly attached to the appliance make sure the steam release knob is closed To install the filter properly simply hold the filter handle flip handle clip backward and place it level under the heater Align the filter holder so that the handle is pointing directly in fornt of the heater Now rotate the handle from left to right until it is tight NOTE Although the optimum pre heating time for the machine is 10 minutes when the selector is in the heater mode VW the machine can be operated after two minutes once the OK light COX is lit Fix the filter as tight as possible in the installation to avoid water leaking from the filter HOW TO PREPARE ESPRESSO COFFEE FILLING THE WATER TANK To remove the water tank simply pull upwards and fill the tank at the sink Do not exceed the MAX level on the water tank The tank may also be filled without removing it simply by pouring water into it directly from a jug e Replace the tank by connecting the valve at the bottom of the tank with the hole in the base of the machine NOTE Do not operate the appliance without water in the tank and always remember to fill the tank when the water level goes below the MIN level The brewing of espresso requires several attachment to be placed in the coffee filter The general operations are described as below 2 cups coffee with ground coffee a Make sure the sealing ring has been placed in the filter holder before
5. fitting the 2 cups filter basket b Fill in the filter basket with appropriate amount of ground coffee 12g recommended and follow general brewing procedures c After brewing grip the filter handle and pressure reducer firmly hold for 5 seconds when removing the filter holder so that the pressure remaining in the filter will be release and the filter can be removed safely NOTE Please check if the sealing ring has been placed properly in the coffee filter before fitting in the coffee filter basket After brewing remember to grip the pressure reducer together with the filter handle firmly when removing the filter so as to avoid the danger of accidental pressure release Every time after brewing remember to clean your coffee filter for hygene and for preventing the coffee grounds from blocking the hole of the reducer Filter basket 2 cups ES Sealing ring a FP2407 Filter holder Pressure reducer 1 cup coffee with ground coffee a Make sure the one cup pressure valve attachment has been placed in the filter holder before fitting in the one cup filter basket b Fill in the filter basket with appropriate amount of ground coffee 6g recommended and follow general brewing procedures c After brewing grip the filter handle and pressure reducer firmly hold for 5 seconds when removing the filter holder so that the pressure remaining in the filter will be release and the filte
6. ground coffee for approximate 30ml espresso the bigger one is for two cups recommend to hold 12g ground coffee for approximate 60ml espresso Tamping the coffee gives a better quality espresso If you press too hard the coffee comes out slowly and the cr ma is dark in colour If on the other hand the coffee is not pressed enough it will come out too quickly and the cr ma will be light in colour Remove any excess coffee from the filter holder rim and attach the filter holder to the machine OTE Tighten the filter handle to avoid leaks Place the pre heated coffee cup underneath the filter holder where coffee drips via the holes Unless you need to make two cups of coffee at the same time When the Ok light is lit you may turn the switch to the Brewing position lt 2 At this point espresso coffee flows into your cup continuously Turn the switch to the Heater position W when there is enough coffee in your cup After brewing turn the switch to OFF position and unplug the coffee maker from the electric socket After brewing wait after the product is cool grip the handle of the filter holder together with the pressure reducer paddle and turn the holder from right to left for removal simultaneously turning the clip of the handle over to cover the filter basket firmly Discard the coffee dregs from the filter basket with moderate force and then clean the filter basket and holder for future use NOTE
7. Mellerware E XECUTIVE Trento Espresso Maker SABS af CE Model OS all E 29200 PLEASE READ ALL INSTRUCTIONS BEFORE USE 2 year guarantee Description Lid for water tank Water tank Steam release knob Control panel 1 cup filter basket Pressure valve for 1 cup of coffee 2 cup filter basket Pressure reducer paddle Filter holder Drip plate Removable drip tray Steam inner tube Steam outer tube OK light Brewing mode Heater light Boiler on function Cappuccino function 0 Off position Selector switch Coffee Tamper Rubber ring for ESE coffee pod Handle clip Sealing ring IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electrical shock and personal injury 1 Read all instructions carefully 2 Do not touch hot surfaces Use handles or knobs 3 To protect against electrical shock do not immerse cord plug or unit in water or other liquid 4 Close supervision is necessary when any appliance is used near children 5 Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance 6 Ifthe supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard 7 The use of accessory attachments not recommended by manufac
8. PRESSO BOILER OUTLET At least twice a year it is necessary to clean the outlet of the espresso boiler in the following manner Check that the coffee machine is not warm and the plug is detached from the mains Using a screwdriver unscrew the screw that holds the outlet of the espresso boiler Using a moist cloth clean the area of the boiler where the outlet was positioned Using a moist cloth clean the area of the boiler where the outlet was positioned Rinse the outlet under the tap still scrubbing it Replace the outlet of the espresso boiler NOTE Do not use solvents or detergents in cleaning the coffee maker Use a soft damp cloth Remove the drip trays empty them and wash them periodically During cleaning never immerse the unit in water it is an electrical appliance DESCALING It is advisable to clean the calcium from the machine every 300 cups of coffee During cleaning it is possible to proceed as follows 1 Fill the tank with water using 1 liter of water Dissolve 2 spoonfuls about 30 grams of citric acid in the water Turn the selector knob to the Heater position and wait until the OK light comes on Check that the filter holder is not attached and place a container under the outlet of the machine Turn the selector knob to the Brew position and allow half of the solution in the tank to flow out Then stop the flow by turning the selector 6 8 9 Allo
9. ck if the sealing ring has been fitted in the filter holder Otherwise it may fail to brew Espresso because the filter has not been completely sealed When using ESE coffee pod fit in FP2407 Filter holder Pressure reducer pad D the o ring after fitting in the ESE coffee pod The ESE Coffee pod have to be purchased separately When placing the pressure valve attachments into the coffee filter please check if the sealing ring has been fitted in the filter holder Otherwise it may fail to brew Espresso because the filter has not been completely sealed o NOT unscrew and remove the filter basket from the machine immediately after brewing the coffee lest the coffee remains will spill out and stain your clothes or even burnt your skins Leave for a while around 5 minutes before removing the filter holder is appropriate 1 N N 4 After preheating the coffee unit as described above put a coffee cup under the filter and set the switch to the Brewing position 2 At this point hot water flows out from the coffee outlet of the filter Turn the switch to the Heater position W again when the Ok light is off Empty the cup and detach the filter Insert the filter basket to the filter holder Then put ground coffee into the filter holder and press it with the coffee tamper OTE The manufacturer has provided two types of filter holder The smaller one is for the one cup recommend to hold 6g
10. e is too finely ground Press the coffee less Decrease the quantity of ground coffee e Clean the outlet as described in Cleaning the espresso boiler outlet section e Only use coffee specifically ground for espresso coffee machines The coffee is not creamy enough or not creamy at all The milk does not froth when making a cappuccino The pressure valve has not been fitted in e The plastic ring for the pressure valve has not been fitted in or has come off e The milk is not cold enough e The cappuccino maker is dirty e Fit in the pressure valve properly e Fit In the plastic ring properly e Always use milk at refrigerator temperature e Carefully clean the pinholes in the milk frother creative housewares 18 Jig Avenue Montague Gardens Cape Town PO Box 37153 Chempet 7442 South Africa Tel 27 21 551 5760 Fax 27 21 551 1189 Service Centre Share Call 086 111 5006 web www creativehousewares co za
11. her of the right type by a qualified professional If the cable is damaged or requires replacing contact a Service Centre authorised by the manufacturer only Never install the machine in an environment that can reach a temperature less than or equal to 0 C if the water in it freezes the coffee maker may be damaged USING IT FOR THE FIRST TIME e When first using this brewer please carry out a cleaning proceedure before it is pre heated fill the container with water to the level marked MAX tighten the filter in place of brewer turn the switch to brewing mode At the same time place an adequate container under the filter holder and make sure the two brewing spouts are over the container Now you can hear the motor of the pump rumbeling Water may take a while to come out of the spout if you are using it for the first time or if it has not been used for some time The cleaning procedure is completed when half the water is left in the container now you can proceed to the pre heat proceedure PRE HEATING THE COFFEE MACHINE e For the proper function as well as longer life in using the coffee brewer remember to fill with water before the heater mode W of the boiler is turned on by turning the selector switch to brewing mode 2 and wait until water drips out from the spout For optimum pre heating the selector switch can be left in the heater mode W for approximately half an hour before making any coffee as long as the
12. nfit persons Children or unfit persons should not be allowed to use this product unsupervised In case of breakdown or malfunctioning turn off the appliance immediately and do not use it For repairs please contact a Service Centre authorised by the manufacturer and request the use of origional replacement parts only The lack of respect for this point may compromise the safe use of the appliance The power supply cable of this appliance must never be replaced by the user because it s replacement requires the use of special tools If the cable should become damaged or in case it needs to be replaced please go to a Service centre authorised by the manufacturer When the appliance is not in use turn off and disconnect the plug from the socket As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible caution and common sense should be applied when operating your appliance particularly in the facinity of young children STALLATION Place the coffee maker on a flat work surface at a safe distance from taps and sinks Check that the voltage corresponds to that indicated on the appliance rating plate The appliance must always be connected to a well earthed socket rated at a 10A minimum The manufacturer is not liable for damage caused by inadequate earthing of the appliance In the event of incompatability of the plug on the appliance and the socket have the plug relaced by anot
13. r can be removed safely NOTE When placing the pressure valve attachments into the coffee filter please check if the sealing ring has been fitted in the filter holder Otherwise it may fail to brew cappuccino because the filter has not been Pressure gt valve attachment Sealing ring completely sealed Filter basket 1 cup remember to grip the pressure reducer together with the filter handle firmly when removing the filter so as to avoid the danger of accidental pressure release Every time after brewing remember to clean your coffee filter for hygene and for preventing the coffee grounds from blocking the hole of the reducer After brewing Filter holder Pressure reducer paddle 1 cup coffee with ESE coffee pod a Make sure the I cup pressure valve attachment has been placed in the filter holder before fitting in the 1 cup filter basket b Fitin a ESE coffee pod to the filter and put the O ring for ESE POD on top of it Follow general brewing procedures c After brewing grip the filter handle and NOTE pressure reducer firmly hold for 5 seconds when releasing the filter holder so that the remaining pressure in the filter will be released and the filter can be removed safely O ring for ESE pod Filter basket 1 cup Pressure valve attachment Sealing ring Tk When placing the pressure valve attachments into the coffee filter please che
14. turer may cause hazards 8 Do not use outdoors 9 Do not let cord hang over edge of table or counter or touch hot surfaces including the stove 10 Do not place on or near a hot gas or electric burner or a heated oven 11 To disconnect turn power select switch to 0 OFF then remove plug from wall outlet 12 This product is intended for household use only Industrial or commercial use invalidates the warranty 13 Do not operate the coffee brewing function and steaming function more than 1 minute ata time SAFETY WARNINGS e This machine has been built to make coffee and to reheat beverages please be careful to avoid burns from the sprays of hot water or steam and avoid any improper use When the appliance is in use do not touch any of the machine s hot hot surfaces e After upacking make sure that the machine is complete and undamaged In case of doubt do not use the appliance and seek the advise of a qualified service professional e Packaging materials plastic bags foam polystyrene etc should not be left withing thereach of children as this could be a potential source of danger IN This appliance is to be utilised for domestic use only Any other use is to be considered improper and therefore dangerous The manufacturer takes no responsibility for damage derived from improper use Never touch the appliance with wet or damp hands Never allow the appliance to be used by children or u
15. w the solution to act for about 15 minutes then start up the flow again until the tank is completely empty 7 To eliminate the remains of the solution and the calcium rinse the tank well fill it with clean water and replace Turn the selector knob to the Brew position and allow all of the remaining solution in the tank to flow out Turn the selector knob to the Heater position and repeat operations 7 and 8 one more time to the O position TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSES SOLUTION Espresso coffee no longer comes out Outlet of Espresso Boiler e Lack of water in the tank The holes in the filter holder spouts are blocked The outlet of the espresso boiler is blocked The tank is badly inserted and the valve at the bottom is not open e Air come into the heater e Fill the water tank e Clean the filter holder or filter basket and coffee pressure valve e Clean as indicated in the Cleaning the espresso boiler outlet section e Press the tank lightly so as to open the valve at the bottom e Open steam release knob for gas release Put the empty cup under the steam outlet of the nozzle Espresso coffee drips from the edges of the filter holder instead of from its holes The filter holder is badly inserted The holes in the filter holder spouts are blocked The plastic ring for the filter holder has not been fitted in or has come off
Download Pdf Manuals
Related Search