Mega Catch Premier MCP800 User's Manual
Contents
1. Mosquito Irap Operation Manual Premier Model MCP800 Pub No USA Version P1006 Contents Page Important Safety Instructions 1 Introduction 2 Features of Mega Catch PREMIER Mosquito Trap 2 Initial Set Up Instructions 3 What Your Mega Catch Mosquito Trap Will Do 4 Installing and Siting the Mega Catch Mosquito Trap 5 6 Stand Assembly Instructions 7 Operation of the Programmable Timer 8 9 Mosquito Catching Systems 10 Using the Liquid Catch Container 10 Using the Catch Bag 11 Fitting of External Skirt 12 13 Care of Your Trap 13 14 Replacement of U V Bulb 14 Mega Catch Octenol Fragrance Strip 15 Optional Accessories 16 Maintenance and Repair of Your Trap 17 19 Removal of Timer 20 Frequently Asked Questions 21 Problem Solving 22 Specifications 22 Parts List 23 Important Safety Instructions e Do not operate the Trap indoors Keep children and pets away from the Trap e Always disconnect power before cleaning servicing or inspecting the inside of the Trap To avoid injury from the High Speed Fan inside the Trap always disconnect power before opening the Door Keep the Door locked and remove the Key while the Trap is operating Plug the Power Cord into a properly grounded electrical outlet protected from weather Do not allow the Trap Transformer Power Cord or plug to be immersed in water e Do not operate the Trap with a damaged Transformer Power Cord or plug e Do not use any extension cord other than the2. 5 Add 3 or 4 teaspoons of a non diet sugar based soft drink This duplicates the fructose content of nectar on which mosquitoes feed 6 Reinstall the Liquid Catch Container into the Mega Catch Mosquito Trap Replace and lock the Door and remove the Key for child safety Reconnect power 7 Before removing the Liquid Catch Container remember to disconnect the power to your Mega Catch Mosquito Trap so that the Fan is not operational Dispose of the contents well away from your dwelling so as to not attract ants It may be necessary to replenish or replace the water solution in the Liquid Catch Container at weekly or more frequent intervals to take account of evaporation This will depend on relevant climatic conditions Using the Catch Bag To prepare your Mega Catch Mosquito Trap follow these steps 1 Ensure that the Trap is switched off by disconnecting the power Attention High Speed Fan inside the Trap may cause injury if the power is not disconnected 2 Unlock and remove the Lockable Door 3 Reach inside the Trap and stretch the open neck of the Catch Bag around the corners of the base of the Fan just above the Fan Safety Guard see figure 4 The Catch Bag has an elastic neck to facilitate attachment 4 Replace and lock the Door and remove the Key for child safety Reconnect power en Before removing the Catch Bag remember to disconnect the power to your Mega Catch Mosquito Trap off so that the Fan is not op
3. Mosquito Trap will start and stop How to Program FIRST SET THE TIME To set the day and time press and hold the CLOCK button while pressing the DAY or HOUR or MINUTE button as the case requires This is the only function that requires two buttons to be pressed at once Mega Catch THEN PRESS PROGRAM TO START PROGRAMMING Start time program 1 Enter start time with HOUR MINUTE buttons For 7 days per week operation select the DAY display which shows all 7 days For individual day operation select the DAY display desired e g Su for Sunday THEN PRESS PROGRAM Stop time program 1 Enter stop time with HOUR MINUTE buttons THEN PRESS PROGRAM Mega Catch Start time program 2 Enter start time with HOUR MINUTE buttons THEN PRESS PROGRAM D ee DD Ey Stop time program 2 Enter stop time with HOUR MINUTE buttons To enter more programs up to 6 repeat previous steps THEN PRESS CLOCK TO RETURN TO NORMAL OPERATION Press the ON AUTO OFF button to change position of the mode indicator ON system will be operating at all times AUTO system will be operating only during programmed times OFF system will not operate at all NOTE If the Trap does not operate when the program mode is set to AUTO it may be in stop time program To check switch the program mode to ON which should start the Trap before returning the program mode to AUTO Mosquito Catching Systems Your Mega Catch Mos
4. No 2 679 688 Output 12V AC 2 08A 25W Parts List Description Part No 1 Mega Catch Premier Mosquito Trap MCP 800 Programmable Timer MC P01 Key MC PU208 Lockable Door MC PU203 External Skirt MC PU1 12 Power Connection Control Box MC PUO5 Top Plate MC PU205 Light emitting Diodes e Di Sa SS N O Internal Power Plugs UV Tube MC PU2 Reflective Surface MC PU211 Bottom Plate MC PU206 Fan Unit MC PU210 Fan Safety Guard MC PU209 Catch Bag MC PU111 Liquid Catch Container MC PU204 Octenol Fragrance Strip MC PU224 60ft Extension Cord MC PU7 Transformer MC P20 N ee lt 7 n gt gt OOO N oO oO a WwW N gt VESER Catch Product made in China for Envirosafe Technologies NZ Limited 16th Floor 120 Albert Street Auckland New Zealand info megacatch com www megacatch com Pub No USA P1006 Printed in China Mega Catch is a trademark of Envirosafe Technologies NZ Ltd
5. accordance with the instructions in this operation manual Ensure you read the Important Safety Instructions at the start of this operation manual Do not operate the PREMIER Trap indoors without first removing the Octenol Fragrance Strip 4 How many traps should buy for around my house This depends on the size of your property Generally we recommend one or two Traps depending on the number and location of mosquito breeding areas on your property A Mega Catch PREMIER Mosquito Trap can in favorable weather conditions attract mosquitoes from up to 120 feet away 5 Will Mega Catch Mosquito Traps catch biting flies The Mega Catch PREMIER Mosquito Trap will catch sandflies black flies and biting midges no see ums and some other biting insects 6 Can stop my Mega Catch Mosquito Trap from catching moths The Mega Catch Mosquito Trap incorporates a low intensity U V Bulb that emits light at a frequency that our research has shown to attract certain mosquito species Unfortunately it can also attract small quantities of non target species like moths If this is a problem the Fluorescent U V Bulb can be removed refer to Page 17 Maintenance and Repair of Your Trap section Problem Solving If your Mega Catch Mosquito Trap fails to operate e Check that the Power Cable is properly connected to both the Trap and the mains and that the power is switched on e Check that the power cable has not been damaged e g by a
6. of top plate A TU Control Box Timer cable 7 lugs into ontrol Box Fan cable plugs into 2 pin socket on underside of top plate Heater cable plugs into 2 pin Power cable socket on underside of top plate Top plate N plugs into Control ES mounts into top slot in body S a 0000001 Bottom plate k mounts into lower slot in body med 00000 UV Bulb C Turn to remove FIG 8 2 Replacement of U V bulb Removal of Timer The Mega Catch Mosquito Trap contains one Nickel Cadmium Battery which is used to energize the Programmable Timer This battery is fitted in a sealed compartment at the rear of the Timer Unit This battery must be recycled or disposed of properly To Remove the Timer Unit refer to figure 8 3 Having opened up the two halves of the Trap 1 Disconnect the cables from the Timer to the Mega Catch Control Box by pulling the Timer Cable Pin from the Control Box 2 Using either your fingers or a screwdriver lift up the two locating arms at the top and bottom of the Timer and then push the Timer Unit out from the inside of the Trap Back of Timer Retaining clip Spread retaining clips each side of timer with flat screwdriver Once released push unit out through trap body Retaining clip FIG 8 3 Removal of Timer Unit Disposal of Timer It is illegal in many states and environmentally undesirable to dispose of the Timer Unit c
7. six the other way Place the Trap on a table ensuring the Programmable Timer is on the side facing down Remove the six screws facing toward you using a hex head screwdriver Then turn the Trap over so that it is timer side up and remove the remaining six screws and nuts Then lift the top half of the Trap away from the bottom half as if it was hinged at the top The top half should now be timer side down on the table and still connected to the bottom half by electrical cables The Top Plate holds the Mega Catch Control Box upperside of Top Plate and the U V Bulb and holders underside of Top Plate NOTE the Mega Catch Control Box is a sealed unit and must not be opened The Bottom Plate holds the heated reflective surface upperside of Bottom Plate and the Fan underside of Bottom Plate Replacement of U V Bulb refer to figure 8 2 Remove the U V Bulb by twisting the tube gently until it is able to be removed Then slot a new U V Bulb into the connector ends and twist the tube gently until it is firmly in position Reinstallation of Plates You should not have any reason to remove the plates from the Trap If however you do merely slot the plates back into the ribs so that the Control Box is on the upper side of the Top Plate and the Fan is on the under side of the Bottom Plate There are arrows on each plate that points to the back of the Trap i e the half that does not contain the Timer when the plates hav
8. staples are supplied to secure frame to ground NOTE For optimum performance place the trap in a predominantly shaded area located between your dwelling and the source of the mosquitoes which is protected from rain and wind Mosquitoes do not fly in strong winds or severe weather conditions For maximum stability the U shaped leg at the back of the stand should be pointed in the direction of prevailing winds The wire staples supplied with the trap or a cinder block placed on the back of the stand can be used to increase stability Operation of the Programmable Timer Your Mega Catch Mosquito Trap is equipped with a high tech Programmable Timer The Timer enables you to program the Trap to operate at times when mosquitos are most active in your area The timer is equipped with an automatically recharging battery This battery can operate for up to three months when fully charged Your Mega Catch Mosquito Trap may need several hours of running to charge up the battery upon initial use NOTE If no display appears on the Programmable Timer when the power is switched on the battery may be discharged To fully recharge the battery run the Trap for 24 hours You can choose to operate the Mega Catch Mosquito Trap in 3 ways 1 ON The Mega Catch Mosquito Trap will run 24 hours a day while connected to a power source 2 OFF the Mega Catch Mosquito Trap will not operate 3 AUTO you can program when the Mega Catch
9. your Authorized Distributor Care of Your Trap Your Mega Catch Mosquito Trap requires very little maintenance The Catch Bag and Liquid Catch Container should be cleaned and washed when required Heavy catches of mosquitoes may result in a build up of material in the internal casing and blade tips of the Fan There may also be a build up of material on the Fan Safety Guard If this happens use the following cleaning technique 1 Ensure the power to your Mega Catch Mosquito Trap is disconnected Attention High Speed Fan inside the Trap may cause injury if the power is not disconnected 2 To remove the Trap from the Stand tip the Trap on its side and slide if off the hook 3 Unlock and remove the Lockable Door Then lay the Trap on its side with the Door opening being face up 4 Reach inside the Trap and remove the Fan Safety Guard attached to base of Fan by turning it counterclockwise see figure 6 5 Using a small sponge or toothbrush and warm soapy water reach into the Trap and carefully clean the inside casing of the Fan and the Fan Blades 6 Ensure that water is not allowed to enter into the Fan Motor Never hose water into the Fan 7 Clean and then replace the Fan Safety Guard 8 Leave the Trap to dry for at least 24 hours before reinstalling it on the Stand and recommencing operation FIG 6 Removal of Fan Safety Guard Bottom plate Lug O Lug Lug To remove safety guard turn counterclockwise until lugs rele
10. Extension Cord supplied with the Trap Ensure Power Cords are placed carefully to avoid causing a tripping hazard Ensure the Trap is properly installed in accordance with this operation manual Read and follow instructions in this operation manual carefully before operating the Trap Your Mega Catch Mosquito Trap should be used in conjunction with other sensible control measures designed to manage mosquito problems e Eliminate standing water in low spots ditches gutters and similar areas e Empty receptacles that collect water e g bird baths and pot plant saucers e Reduce breeding sites by keeping grass mown e Mosquito netting screens can be used to provide mosquito free areas e Light coloured clothing is less attractive to some mosquito species and if tightly woven can give some protection against biting e DEET is considered the most effective mosquito repellent but should not be used too heavily Introduction Mosquitoes have been described as the most dangerous creatures on Earth Aedes mosquitoes may carry yellow fever and dengue fever Culex mosquitoes may carry several strains of encephalitis including St Louis Encephalitis Eastern Equine Encephalitis and West Nile Virus and Anopheles mosquitoes may carry malaria Male mosquitoes do not bite The real risk is from female mosquitoes which bite when in search of blood to provide protein for their eggs Scientific research over the past 50 years has shown tha
11. al and the black negative to the negative battery terminal can result in major damage to your Mega Catch Mosquito Trap and may void your warranty 2 Cigarette Lighter Car Accessory Terminal Cable The Mega Catch Mosquito Trap can be operated from your vehicle s accessory terminal using the factory approved Accessory Cable Your Authorized Distributor can supply a factory approved Accessory Cable NOTE Failure to use only the factory supplied Cable could result in damage to your Mega Catch Mosquito Trap and may void your warranty Maintenance and Repair of Your Trap Opening the two halves of the Mega Catch mosquito Trap will be necessary for the following purposes e Replacement of U V Bulb The U V Bulb should last for approximately two mosquito seasons but as with all light bulbs life expectancy is variable depending on actual usage and climate e Annual service At the end of each season the Internal Plates heated reflective surface and Fan should be cleaned using warm soapy water and allowed to dry thoroughly e Battery removal The Programmable Timer contains a Nickel Cadmium Battery This must be disposed of correctly when the Trap reaches the end of its life Opening the Trap refer to figure 8 1 ATTENTION Always disconnect the power to your Mega Catch Mosquito Trap before opening the Trap The two halves of the Trap are held together with 12 stainless steel screws and nuts six facing one way and
12. ase Lug fiala Rotate clockwise to fit fan housing with 4 slots on safety guard then turn clockwise until tight The casing of your Mega Catch Mosquito Trap is made from polypropylene which is extremely strong and durable lts appearance is best maintained by a plastic protector of the type used on plastic car fenders Do not use wax In order to prolong the life of your Mega Catch Mosquito Trap store it and the Mega Catch Stand in a dry place when not in operation Your Mega Catch Mosquito Trap should be serviced at the end of each season see Page 17 Maintenance and Repair of Your Trap section Replacement of U V Blub The U V Bulb is a consumable item and replacements can be obtained from your Authorized Distributor To install a new U V Bulb refer to Page 17 Maintenance and Repair of Your Trap section Mega Catch Octenol Fragrance Strip Some but not all mosquito species are attracted to minute quantities of a chemical called octenol 1 OCTEN 3 OL Each Mega Catch Mosquito Trap comes with a Mega Catch Octenol Fragrance Strip NOTE When operating the PREMIER Trap indoors DO NOT USE a Mega Catch Octenol Fragrance Strip To install or replace the Octenol Fragrance Strip 1 Ensure the power to your Mega Catch Mosquito Trap is disconnected 2 Unlock and remove the Lockable Door 3 Remove the Mega Catch Octenol Fragrance Strip from its pouch and be careful not to touch the expose
13. d holes on its surface Place the strip inside the Trap in the position shown in figure 7 below Replace and lock the Door and remove the Key for child safety Reconnect power Wash your hands after this procedure has been completed FIG 7 Placement Position for Mega Catch Octenol Fragrance Strip Octenol Fragrance Strip Lap Slot Place Mega Catch Octenol Fragrance Strip in the trap as shown Mega Catch Octenol Fragrance Strips should be effective for up to 30 days depending on weather conditions Mega Catch Octenol Fragrance Strips are a consumable item and replacements can be obtained from your Authorized Distributor NOTE Octenol can improve the rate of capture of some mosquito species Other species e g the Asian Tiger Mosquito may not be attracted or even repelled by octenol You should determine what is best in your area by experimenting without the Mega Catch Octenol Fragrance Strip in place ATTENTION Keep Mega Catch Octenol Fragrance Strips out of reach of children Read directions and Important Safety Instructions carefully before use Optional Accessories 1 Battery Terminal Power Cable The Mega Catch Mosquito Trap can be operated using a 12 volt car battery as a power source Your Authorized Distributor can supply a factory approved Power Supply Cable complete with positive and negative alligator clips NOTE Failure to connect the red positive connector to the positive battery termin
14. e been properly installed Connection of Wires You should not have any reason to remove any of the electrical connections except as part of the battery disposal process see Page 20 Removal of Timer section All electrical connections are by push in pin connectors Provided these are not forced it is not possible to plug any connector into the wrong connector hole There are three connector holes on the underside of the Top Plate The two smaller two pin connector holes are for the Fan and Heater Cables These two connections are interchangeable so it doesn t matter which of these two connector holes the Fan and Heater are plugged into The third connection on the underside of the Top Plate is a three pin hole and fits only the U V Bulb Connection Cable The connection holes into the Control Box on the upperside of the Top Plate are all different sizes and fit the remaining cables Re assembly of Trap With the Top and Bottom Plates in place replace the timer side or top half of the Trap ensuring that each plate slots into the locating ribs The 12 screw holes should now be aligned for replacement of the screws and nuts Hold the nuts into the pre formed hexagonal holes and carefully screw in the screws NOTE Do not overtighten the screws This could cause the nuts to rotate and damage the pre formed hexagonal fittings in the plastic housing FIG 8 1 Opening the PREMIER Trap U V cable plugs into 3 pin socket on underside
15. erational Then pull the drawstring tight so that any mosquitoes that remain alive cannot escape Crush the top of the Catch Bag down on its base to kill any mosquitoes that do remain alive Dispose of the contents well away from your dwelling so as not to attract ants Mosquitoes collected in the Catch Bag will usually die very quickly without access to moisture In cooler climates they may live for a longer period In times of heavy infestations of mosquitoes it may be necessary to empty the Catch Bag on a regular basis in order to ensure optimum operation of the Trap FIG 4 Fitting of Catch Bag Stretch open neck of Catch Bag over corners of fan housing base Trap Fan Housing Catch Bag Catch Bags should be hand washed in warm soapy water from time to time Catch Bags are a consumable item and replacements are available from your Authorized Distributor Fitting of External Skirt Your Mega Catch Mosquito Trap comes with an External Skirt which fulfils two important functions First its color and texture provides a visual attractant for several species of mosquitoes Secondly it acts as a baffle directing the air plume out of the bottom of the Trap There are two methods which you can use to fit the Skirt Method One is the easiest Method One 1 Place the Mega Catch Mosquito Trap on a table or other flat surface 2 Slide the Skirt on from the top of the Trap over 2 corners initially with the elastic band at the
16. lawn mower or animals squirrels dogs or racoons e Check that the Programmable Timer is set to the ON position e Check that the Programmable Timer if set to AUTO is set to operate at the time you are checking its operation If these steps fail then email us at info megacatch com or call the Service Centre number shown on the separate Warranty Certificate If the lights in the Mega Catch Mosquito Trap come on but the Fan fails to operate e Check whether there has been a build up of material in the Fan and or Fan Safety Guard which is preventing the Fan blade from turning Refer to Page 13 Care of Your Trap section If these steps fail then email us at info megacatch com or call the Service Centre number shown on the separate Warranty Certificate NOTE Do not attempt to access the internal electronic components of your Mega Catch Mosquito Trap Opening of sealed units will void your warranty Need Help For service repair or any questions concerning Mega Catch products email us at info megacatch com or call the Service Centre number shown on the separate Warranty Certificate Do NOT return products to the place of purchase Do NOT return products to an Authorized Distributor You may also want to consult our website www megacatch com Specifications Power Source AC Adaptor YL 25 12 U S Design Patent No 449 091 CSA Listing E207075 37XZ U S Patent No 6 199 316 Input 120V AC 60Hz U S Trade Mark Reg
17. ontaining the battery in municipal trash A fee has been paid to the Rechargeable Battery Recycling Corporation RBRC to collect these batteries and recycle them rather than incinerate or bury them For information on our battery recycling program call our toll free consumer assistance number 1 800 231 9786 or call RBRC at 1 800 822 8837 for instructions on proper disposal Frequently Asked Questions 1 Will my Mega Catch Mosquito Trap permanently eliminate mosquitos in the area No There is no single silver bullet to eliminate mosquitos The best you can do is devise an effective mosquito management plan for your area using the best available control strategies including one or more Mega Catch Mosquito Traps 2 How often do need to operate my Mega Catch Mosquito Trap Before using your Mega Catch Mosquito Trap note the time of day when mosquito activity is greatest If for example this is in the morning and the evening then you should set the Trap using the Programmable Timer to operate at these times Where your mosquito problem involves night time biters we recommend operation of the Trap between 7pm and 11pm and 4am and 8am If mosquito activity is all day then you may need to operate the Trap 24 hours per day until the mosquito population declines 3 Is the Mega Catch Mosquito Trap harmful to me or my pets No The Mega Catch PREMIER Mosquito Trap can be used around humans and pets provided it is operated in
18. ppear on the face of the Timer If it does not see Page 8 Operation of the Programmable Timer section Set the Timer to ON for continuous running or to AUTO to program operating times See Page 8 Operation of the Programmable Timer section for programming instructions 14 When the Trap is operating the Fan should be running the four diode lights should be flashing intermittently and the U V Bulb light should be on If the Trap is not operating correctly then re read these instructions or refer to Page 22 Problem Solving section or email us at info megacatch com What Your Mega Catch Mosquito Trap Will Do Your Mega Catch Mosquito Trap is designed to reduce mosquito populations but it will not permanently eliminate them Operate the Mega Catch Mosquito Trap daily for several weeks Over this time you should notice a decline in mosquito numbers This means your Trap is doing its job The Mega Catch Mosquito Trap is not designed to compete with humans in close proximity eg at a barbecue If you are planning an outdoor function operate the Trap for several days before the function NOTE Your Mega Catch Mosquito Trap should be used in conjunction with other sensible control measures designed to manage mosquito problems Installing and Siting the Mega Catch Mosquito Trap Installation of Trap Your Mosquito Trap comes fully assembled To install first follow the instructions on Page 3 Initial Set Up In
19. quito Trap comes complete with a Catch Bag and a Liquid Catch Container You may choose to collect mosquitoes using either of these systems Our research has shown the Liquid Catch Container system to be more effective This is because when the Mega Catch Mosquito Trap is operated using a Liquid Catch Container the air plume emanating from the bottom of the Trap is humidity enriched Depending on local temperatures evaporation may mean that it is necessary to replenish water in the Liquid Catch Container weekly or even more frequently The Catch Bag system requires less frequent attention and therefore may be your preferred mosquito catching system Smaller biting insects eg no see ums are best caught using the Liquid Catch Container because the mesh size on the standard Catch Bag may be too large to capture them Using the Liquid Catch Container To prepare your Mega Catch Mosquito Trap follow these steps 1 Ensure that the Trap is switched off by disconnecting the power Attention High Speed Fan inside the Trap may cause injury if the power is not disconnected 2 Unlock and remove the Lockable Door 3 Slide the Liquid Catch Container out from beneath the Fan This container has locating feet on its base 4 Fill the container with water until it is approximately two thirds full Add 3 or 4 drops of liquid detergent soap and stir thoroughly This breaks the surface tension of the water ensuring that mosquitoes drown upon capture
20. structions section The Initial Set Up Instructions assume that you have decided to install your Mega Catch Mosquito Trap on the Stand that is supplied with the Trap Alternatively you may decide to hang the Trap from a tree or a fixed post using a chain nylon rope or wire connected to the attachment hole at the top of the Trap We recommen a height of around 3 feet 1 meter from the ground to the top of the Mega Catch Mosquito Trap However you may need to adjust the Trap s height depending on the type of mosquitoes you are catching Your Mega Catch Mosquito Trap is supplied with a 60 foot 18 meter low voltage extension cord with weatherproof fittings To avoid the cord posing a tripping hazard or being damaged e g by a lawn mower we recommend that if possible it be placed 2 3 inches 50 75 mm underground This can be easily achieved by using a spade which is inserted into the ground and moved backwards and forwards to create a shallow slit trench into which the cord can be pushed before the ground is replaced by standing on the top of the slit trench Mosquito source Siting of Trap Prevailing Wind Direction x FIG 1 Trap Positioning For the best performance from your Mega Catch Mosquito Trap first determine the source of the mosquito nuisance Mosquitoes breed in wet areas like streams marshland wooded areas and gardens Then use these rules to site the Trap Rule 1 Place the Trap between the mosqui
21. t female mosquitoes find their prey using a combination of sensory cues including light shape color heat vibration sweat and other by products of human activity Using that research and with the benefit of extensive field testing including tests by the United States Department of Agriculture in Gainesville Florida Mega Catch has developed one of the world s most advanced mosquito traps the Mega Catch PREMIER Mosquito Trap Features of Mega Catch PREMIER Mosquito Trap The Mega Catch PREMIER Mosquito Trap has been designed for indoor or outdoor use NOTE when operating the PREMIER Trap indoors remove the Mega Catch Octenol Fragrance Strip The PREMIER can operate unattended for long periods It can be programmed to start and stop according to peak mosquito activity in your area It features an electronically controlled diode lighting system that produces intermittent light at oscillating frequencies selected to coincide with spectral sensitivity peaks for many mosquito species It also features a low intensity U V or black light bulb Mosquitoes attracted to the PREMIER by visual and other cues seek to land on and probe specially designed surfaces and enter the Trap where they are collected in the Catch Bag or Liquid Catch Container Initial Set Up Instructions Before attempting operation of your PREMIER Trap follow these instructions l 2 3 4 5 Remove the Trap from the carton Remove the box containing
22. the Stand from the carton Assemble the Stand see Page 7 Stand Assembly Instructions section Remove the box marked Accessories from the base of the carton Fit the External Skirt to the outside of the Trap by sliding the skirt on from the top of the Trap so that the opening is directly in front of the Door see Page 12 Fitting of External Skirt section Note Failure to position the Skirt correctly will result in a NIL mosquito catch Your PREMIER Trap has two mosquito collection methods a dry catch system using a Catch Bag and a wet catch system using a Catch Container In most circumstances the wet catch system offers superior catch performance to the dry catch system The dry catch system using the Catch Bag is better for mosquito species identification If you wish to catch mosquitoes using the Catch Bag then attach the Catch Bag to the base of the Fan inside the Trap The Catch Bag has an elastic top to facilitate attachment see Page 10 Mosquito Catching Systems section If you wish to catch mosquitoes using the wet catch system fill the Liquid Catch Container two thirds full with fresh water Add 2 or 3 drops of liquid detergent soap to break the surface tension of the water Also add 3 or 4 teaspoons of a non diet sugar based soft drink Then place the Liquid Catch Container in the Trap using the locating feet on its base Remove the Mega Catch Octenol Fragrance Strip from its pouch being careful not to touch the e
23. to source and areas of human activity Rule 2 Place the Trap as far away from people and as close to the mosquito source as possible Attract them to the Trap and not to you Rule 3 Place the Trap upwind of the mosquito source but only if you can comply with Rule 1 Mosquitoes sometimes use the wind to navigate Rule 4 Place the Trap in a predominantly shaded area Most mosquitoes avoid direct sunlight Rule 5 Place the Trap in a location protected from rain and strong wind Mosquitoes don t fly in strong winds Rule 6 If severe weather conditions are predicted then store the Trap out of the weather For maximum stability point the small U shaped leg at the back of the Stand into the prevailing wind and pin the base to the ground using the wire staples supplied with the Stand While your Mega Catch Stand is zinc plated and powder coated when not in use we recommend that it be stored out of the weather Stand Assembly Instructions To assemble the Stand supplied with the Trap follow the instructions shown in figure 2 below Fix external skirt then tip the Trap on its side and slide onto hook Wind direction I Fit top section over bottom section of upright then fit bolt and tighten firmly FIG 2 Trap Assembly Instructions N GD Assemble stand base components as illustrated here fit all bolts and washers before tightening bolts firmly Screw feet into bottom of stand base SS 3 x 4 Wire
24. top 3 The Skirt is properly fitted when the elastic band is seated over the lower horizontal rib just below the inlet holes see figure 5 The opening in the Skirt should be located at the front of the Trap so as to facilitate removal of the Door without having to remove the Skirt The hook and loop fastening on this opening should be closed when the Trap is running FIG 5 Fitting External Skirt External Skirt sS Hook and loop fastening Method Two 1 Hang the Mega Catch Mosquito Trap from the Stand see Page 4 Initial Set Up Instructions section paragraph 11 2 Slide the Skirt up from the bottom of the Trap over 2 corners initially with the elastic band at the top 3 The Skirt is properly fitted when the elastic band is seated over the lower horizontal rib just below the inlet holes see figure 5 The opening in the Skirt should be located at the front of the Trap so as to facilitate removal of the Door without having to remove the Skirt The hook and loop fastening on this opening should be closed when the Trap is running NOTE Failure to position the skirt correctly will result in a NIL mosquito catch The Skirt is not manufactured from a U V resistant material but this will not be an issue if the Trap is operated in shaded conditions as recommended The Skirt can be reversed should one side begin to fade from exposure to U V light The Skirt is a consumable item and replacements can be obtained from
25. xposed holes on its surface Place the strip inside the Trap see Page 15 Mega Catch Octenol Fragrance Strip section Wash your hands after this procedure has been completed Reinstall the Door by locating the base of the Door in the Trap and then pushing firmly until Door clicks into place Lock the Door using one of the two Keys provided with the Trap and then remove the Key NOTE Removing and reinstalling the door is designed to require a reasonable amount of force to make it difficult for children Hang the Trap from the hook on the Stand in the direction shown in the Stand Assembly Instructions To achieve this hold the Trap in an upright position so that the top of the Trap is next to the hook on the stand Then swing the bottom of the Trap outwards through an arc of about 45 degrees and you will see that the top of the Trap will fit through the gap in the hook This is a design feature to prevent the Trap falling off the stand accidentally 12 Your PREMIER Trap comes with a low voltage transformer and a 60 foot 18 meter low voltage extension cord with weatherproof connectors Plug the extension cord into the Trap connection turning the connector clockwise until tight Plug the extension cord into the transformer cable turning the connector clockwise until tight Then plug into the power supply NOTE The connectors are designed to be a tight fit to ensure that they are weatherproof 13 Turn on the power A display should a
Download Pdf Manuals
Related Search