McIntosh MC-2105 User's Manual
Contents
1. 20 l Sitch N WWA NOILYOLSIG JINONY WH 1101 06270 LY indino ee ROU IO 39VLNIIH3d 001 SE N A PERFORMANGE PER CHANNEL BOTH CHANNELS OPERATING inaino H3MOd NOILHOLSIG HINOWHYH Technical Description A two stage amplifier with three transistors in each channel increases the input voltage 16 dB There are 13 transistors in each power amplifier section The two stage preamplifier is fed to a pair of matched transistors arranged as an emitter coupled amplifier with two inputs and one output The signal from the preamplifier section connects to one of these inputs Both and DC negative feedback are applied to the other input This large quantity of feedback is used to reduce noise and distortion The signal is then fed to a voltage ampli fier The voltage amplifier is followed by two driver transistors The output section is arranged as a series push pull amplifier The power transistors used in the output section of your MC 2105 are selected for their high power dissipation capability wide fre quency response and large safe operating area In addition each power transistor is given four separate tests before it is put in your MC 2105 This additional testing makes sure your MC 2105 will deliver its rated power from 20 to 20 kHz with low distortion and complete reliability The power transistors are2. 4 Ma GE 1 3 mI OWLS 31015 005 INIT 13431 4331 HOW to Use the Dynamic Peak Locking Meters Ordinary meters lack the capability of indicating the short interval power in a sound wave The mass of the meter movement is too great to re spond to instantaneous changes in music program material McIntosh superior engineering has de veloped new circuitry that permits the meters on the MC 2105 to respond to the short interval power in a sound wave to an accuracy of 98 of the true value This is another McIntosh development that represents a major step forward in the use of power level meters There are two circuits that give these meters the indicating capability of the short interval power in a sound wave The first circuit is an accelerating circuit that compensates for the inertia character istics of the meter movement Because the short interval power fluctuation is so rapid the eye might not perceive the instantaneous power read ing This caused the development of the second circuit which is a time stretching circuit The time stretching circuit delays the movement of the meter needle at peak reading for a few milli seconds With the aid of the CBS test record STR1000 the frequency response of your phono cartridge can be measured The graph on page 7 shows the ideal RIAA cur
3. Mentosh MC 2105 THE MCINTOSH 2105 SOLID STATE STEREO POWER AMPLIFIER Reading Time 28 Minutes Price 1 25 Your 2105 Stereo Power Amplifier will give you many years of pleasant and satisfactory performance If you have any questions please contact CONTENTS SERVICE CONTRACT 1 INSTALLATION 2 3 HOW TO CONNECT 45 HOW TO USE THE DYNAMIC PEAK LOCKING METERS FRONT PANEL INFORMATION PERFORMANCE LIMITS AND RATINGS 9 TYPICAL PERFORMANCE CHARTS 10 TECHNICAL DESCRIPTION 11 BLOCK DIAGRAM 12 CUSTOMER SERVICE Mcintosh Laboratory Inc 2 Chambers Street Binghamton New York 13903 Phone 607 723 3512 WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE Take Advantage of 3 years of FREE Factory Service Fill in the Application NOW rach len Geta ea SERVICE CONTRACT Anapplication fora FREE THREE YEAR FACTORY SERVICE CONTRACT is included with this manual ri h Be Be The terms of the contract are or mishandling is not covered by the SERV ICE CONTRACT 4 The SERVICE CONTRACT is issued to you as the original purchaser To protect you from misrepresentation this contract cannot be transferred to a second owner 1 Mcintosh will provide all parts materials and labor needed to return the measured perform ance of the instrument
4. amplifier delivers 5 watts A meter reading of 3 2dB indicates 105 watts power output HEADPHONE Use the jack for low impedance stereo headphones The headphone jack is on at all times SPEAKERS OFF The loudspeakers are turned off when the SPEAKER switch is in the OFF position You can listen to headphones in private THIS SWITCH MUST BE IN THE ON POSITION TO HEAR MUSIC FROM THE LOUDSPEAKERS ON Music will be heard through the loudspeakers Use this as the normal listening position POWER The power switch turns the MC2105 on or off The switch does not control the power outlet on the back panel If you wish to control the operation of the on off switch from a preamplifier control center leave the switch in the ON position In this case be sure to plug the AC cord of the MC 2105 into the controlled outlets on the rear of the preamplifier control center OFF In the OFF position the AC to the amplifier is turned off Be Mt 2105 SOLITT SLATE POWER AMPLIFIER SPEAKER lea GH 4 Performance Limits and Ratings PERFORMANCE GUARANTEE Performance Limits are the maximum deviation from perfection permitted for a instrument We promise you that the 2105 you buy must be capable of performance at or exceeding these limits or you get your money back Mcintosh is the only manufacturer that make this guarantee PERFORMANCE Mcintosh audio power ratings are in accordanc
5. at 16 ohms output INPUT IMPEDANCE 200 00 ohms INPUT SENSITIVITY 0 5 volt Level control provided for higher input voltage GENERAL INFORMATION POWER REQUIREMENTS 120 volts 50 60 Hz 75 watts at zero signal output 430 watts at rated output SEMICONDUCTOR COMPLEMENT 34 silicon transistors 18 silicon rectifiers and diodes MECHANICAL INFORMATION SIZE Front panel measures 16 3 16 inches wide 41 12 cm by 71 8inches high 18 1 cm Chassis measures 15 inches wide 38 1 cm by 6 9 16 inches high 16 67 cm 1412 inches deep 36 83 cm including connectors Knob clearance required is 172 inches 3 81 cm in front of mounting panel FINISH Front panel is anodized gold and black with special gold teal nomenclature illumination Chassis is chrome and black MOUNTING Exclusive Mcintosh developed professional PANLOC WEIGHT 65 pounds 29 48 kg net 77 pounds 34 93 kg in ship ping carton SPECIAL FEATURES The amplifier is completely stable when connected to any loudspeaker system or even to any reactive loads The MC 2105 has special circuits to prevent damage by short circuit or open circuit of the output loads or by any amount of output impedance mismatch Thermal cutouts are mounted on the output transistor heat sinks to provide protection in the event of inade quate ventilation Peak reading peak locking meters feature special cir cuit to respond to peak value of complex input signal SS ee 000
6. fail ure of the power output transistors due to exces sive mismatch of the output When your MC 2105 operates normally the SENTRY MONITORING CIR CUIT has no effect on signals passing through the power amplifier If the power dissipation should rise above normal operation the SENTRY MONI TORING CIRCUIT restricts the drive to the output transistors The SENTRY MONITORING CIRCUIT acts instantaneously for any input signal or load combination This arrangement assures complete circuit reliability Only McIntosh gives you this de gree of protection POWER SUPPLY SECTION There are three separate power supply sections One positive and one negative high current supply is used for the output stages The other positive supply is used for the driving amplifier stages All supplies are full wave and use silicon rectifiers Adequate filtering is used to assure an absolute mininum of hum The power output stage filter Capacitors have very high capacity which allows full power output below 20 Hz The power trans former is generous in size and runs cool even under heavy use Block Diagram MCINTOSH LABORATORY INC 2 CHAMBERS ST BINGHAMTON N Y 13903 607 723 3512 Design subject to change without notice Printed in U S A 038 799
7. mounted on oversized anodized heat sinks The heat sinks assure that under normal operation the transistors will operate at a low temperature If temperatures increase due to a shorted speaker or restricted ventilation an automatic temperature sensing device turns off the MC 2105 The device operates automatically at a preset temperature The 2105 will turn on again when the temperature has returned to normal limits This additional feature gives your MC 2105 complete reliability under the most extreme oper ating conditions The output stages are matched to the load by the McIntosh autoformer The Mcintosh autoformer is carefully wound using Mcintosh trifilar winding and interleaving techniques Trifilar winding and interleaving gives the transformers exceptional bandwidth The autoformers properly match the power transistors to 4 8 and 16 ohm loads at all audio frequencies The use of the Mcintosh designed trifilar auto former makes the Mcintosh solid state amplifiers the only amplifiers that deliver FULL POWER AT ALL SPEAKER IMPEDANCES You have not been power penalized for your choice of loudspeakers when using the McIntosh MC 2105 Another of the advantages of the autoformers is the 25 volt output for a constant voltage distribu tion system With the MC 2105 several sets of speakers can be operated independently through out your home To further insure reliability a special power out put SENTRY MONITORING CIRCUIT prevents
8. anel information LEFT GAIN Use the left gain control to adjust the volume in the left channel to the desired listening level Turn the control clockwise to increase the volume RIGHT GAIN Use the right gain control to adjust the volume in the right channel to the desired listening level Turn the control clockwise to increase the volume METER RANGE The meter switch has four positions The first position is OFF With the switch in the OFF position there is no indication on the meters 0 In this position of the meter range switch the amplifier will deliver 100 watts when the meter indi cates 3dB with meter indication of 0 the ampli fier delivers 50 watts with a meter indication of 3dB 10 In this position of the meter range switch the amplifier will deliver 5 watts output when the meter indicates 0 With a meter indication of 3dB the amplifier delivers 2 watts output and a 10dB meter indication the amplifier delivers watt 20 In this position of the meter range switch the amplifier will deliver watt 500 milliwatts when the meter indicates 0 With a meter indication of 3dB the amplifier delivers watt 250 milliwatts a 10dB meter indication the amplifier delivers 50 milliwatts LEFT GAIN 10 a A po OFF 3 METER RANGE 0 RIGHT GAIN amplifier delivers 25 watts and a meter indication of 10dB the
9. at 2 If the cutout is to be located from the rear of the panel begin here 1 On the back of the cabinet panel scribe a vertical centerline through the exact center of the area in which the cutout is to be made Place the template against the back of the panel and match the template centerline with the centerline on the cabinet panel Make sure that there is at least inch clear ance between the bottom of the dashed line of the cutout area on the template and any shelf or brace below the proposed cutout Mark the two locating holes C holes on the mounting template Drill the two locating holes Be certain the drill is perpendicular to the panel Now position the template on the front of the panel by aligning the locating holes on the template with the drill holes 2 If the cutout is to be located from the front the panel With the template in place against the cabinet panel mark the A and B drill holes and the four small holes that identify the corners of the cutout Join the corner marks with a pen cil The edge of the template can be used as a straight edge IMPORTANT DRILL THE 6 HOLES BEFORE MAKING THE CUTOUT Accurately drill the three holes on each side of the cutout area with a 16inch drill With the saw on the INSIDE OF THE PENCIL LINES carefully cut out the rectangular opening Secure the mounting strips to the rear of the cabinet panel using two screws from the hardware package In
10. e with the Federal Trade Commission Regulation of Novem ber 4 1974 concerning power output claims for ampli fiers used in home entertainment products POWER OUTPUT 105 watts minimum sine wave continuous average power output per channel both channels operating into 4 ohms 8 ohms or 16 ohms load impedance which is 20 5 volts RMS across 4 ohms 29 0 volts RMS across 8 ohms 41 0 volts RMS across 16 ohms OUTPUT LOAD IMPEDANCE 4 ohms 8 ohms or 16 ohms separate ter minals are provided for each output RATED POWER BAND 20 Hz to 20 000 Hz TOTAL HARMONIC DISTORTION 0 25 maximum harmonic distortion at any power level from 250 milliwatts to 105 watts per channel from 20 Hz to 20 000 Hz both channels operating INTERMODULATION DISTORTION 0 25 if instantaneous peak power output is 210 watts or less per channel with both channels operating for any combination of frequencies 20 Hz to 20 000 Hz FREQUENCY RESPONSE 20 Hz to 20 000 Hz 0 0 25 dB 10 Hz to 100 000 Hz 0 3 0 dB at one watt output NOISE AND HUM 90 dB below rated output OUTPUT POWER MONITOR METER Meter is calibrated to read 3 dB when amplifier pro duces 105 watts Meter range switch is provided to increase meter sensitivity by 10 dB or 20 dB Calibration accuracy at O dB reading is 2 at all frequencies meter range accuracy is 5 RATINGS OUTPUT VOLTAGES 25 volts for distribution lines DAMPING FACTOR 13 at 8 ohms output 18 at 4 ohms output 10
11. ll steps outlined for tape playback charac teristics 3 A comparison of the two curves will give the recording characteristics of your tape re corder A deviation of 3 dB is acceptable Similar checks can be made on all program sources in your stereo system Follow the same general procedure for any program source for which a standard reference is available IDEAL RIAA SYSTEM RESPONSE USING CBS STR 100 TEST RECORD LIL TR LLI LILLE ES EEE EEE DEREN NEE 254 gt BEEEIERE a 1 OO NETT MEERE skh LI LEL LA Y EFT a LN E E E ll RRA ie ZO LUN T TE Ll CA RE LLL nn a A PE Lo La E LA Ll TNT TEL TER 1 1 TJ ER ee E DS LLI LN O 20 0 10 000 20 000 SE N ES ll 164 IT HN 10 ENE TIER m Hr se 0 LL TLI Ne 011 Hr 20 1 000 10 000 20 000 FREQUENCY IN Hz 7 RELATIVE OUTPUT LEVEL IN dB RELATIVE OUTPUT LEVEL IN dB Front P
12. ly found that each 10 centigrade 18 F rise in tempera ture reduces the life of electrical insulation by one half Adequate ventilation is an inexpensive and effective means of preventing insulation breakdown that results from unnecessarily high operating tem peratures The direct benefit of adequate ventila tion is longer trouble free life Allow at least 15 inches deep x 17 inches wide x 8 inches high for mounting the MC2105 Always allow for air flow by either ventilation holes or space next to the bottom of the amplifier and a means for a warm air to escape at the top With adequate ventilation the amplifier can be mounted in any position To prepare the MC 2105 for installation remove the plastic protective covering Turn it upside down so that it rests on its top on the shipping pallet Remove the four plastic feet fastened to the bot tom of the chassis Next place the mounting brackets the parts bag and the mounting template at hand The PANLOC professional mounting design eliminates the need for any shelf or bracket to support the MC 2105 lt is completely supported by its own mounting brackets The design of the mounting template allows you to position or locate the cutout from the front or rear of the panel to which the instrument is to be mounted Position the plastic mounting template over the area of the panel to be cut out for installa tion If the cutout is to be located from the front of the panel begin
13. nstallation HOWtoConnect INPUT STEREO The shielded cable from the left output of the Mcintosh preamplifier is plugged into the left jack The shielded cable from the right output of the Mcintosh preamplifier is plugged into the right jack SPEAKERS Speakers are connected at the barrier strips marked OUTPUT on the back panel of the ampli fier Use lamp cord bell wire or wire with similar type of insulation to connect the speakers to the amplifier For the normally short distances of under 50 feet between the amplifier and speaker 18 wire or larger can be used For distances over 50 feet between the amplifier and speaker use larger wire The loudspeaker impedance is usually identified on the loudspeaker itself Connect one of the leads from the left loudspeaker to the screw marked COM on the LEFT OUTPUT barrier strip Connect the other lead from the left loudspeaker to the screw marked with the number corresponding to the speaker impedance on the LEFT OUTPUT barrier strip Connect one of the leads from the right loudspeaker to the screw marked COM on the RIGHT OUTPUT barrier strip Connect the other lead from the right loudspeaker to the screw marked with the number corresponding to the speaker impedance on the RIGHT OUTPUT barrier Strip The only adverse effect on the operation of a McIntosh amplifier when it is improperly matched is a reduction in the amount of distortion free power available to the loudspeaker Close im
14. ped ance matching is desirable for maximum distor tion free power SPEAKER CONNECTIONS Use this table to determine proper speaker con nection Connect the If the speaker impedance speaker leads is between between COM and 3 2 to 6 5 ohms 4 ohms 6 5 to 13 ohms 8 ohms 13 to 26 ohms Connect as follows 16 ohms Connect one right speaker Connect one lead to the lf the left speaker to screw marked speaker screw LEFT RIGHT COM imped COM and and the other ance 15 other to to 4 ohms LEFT 4 RIGHT 4 8 ohms LEFT 8 RIGHT 8 16 ohms LEFT 16 RIGHT 16 DO NOT CONNECT A MONOPHONIC LOUD SPEAKER TO BOTH TERMINALS THE LOUD SPEAKER CAN BE DAMAGED For 25 volt line operation connect one of the left leads to the screw marked COM on the LEFT OUT PUT barrier strip The other left lead is connected to the screw marked 8W on the LEFT OUTPUT barrier strip Connect the right leads in the same manner on the RIGHT OUTPUT barrier strip AC POWER The MC 2105 operates on 117 to 130 volt 50 60 Hz The amplifier will be turned on and off if its power cord is plugged in one of the auxiliary AC power outlets on the program source 39Vd SNOILOANNOD 45 335 SYSNVadS LOANNOOD OL ee re 4a ind 4437 pe om 1012 JW E
15. sert the screws in the center holes of the cabi net panel B holes on the template and tighten The screw head should pull into the wood slightly Use two inch long screws for panels under 12 inch or two 1 inch long screws for panels inch thick and larger Attach the mounting brackets to the cabinet panel using four screws Place the template over the mounting screws The mounting screws should be centered in the A and B holes on the template The sides of the mounting brackets should match the vertical dash lines on the template If necessary loosen the screws and push the brackets into alignment and retighten Insert the power cord through the opening Care fully slide the MC 2105 into the opening so the rails on the bottom of the equipment slide in the track of the mounting brackets Slide the instrument in until it stops at the adjust position latches Press the latches in and continue to slide the instrument in until the front panel is against the cabinet panel At the bottom front corners of the PANLOC instru ments are the PANLOC buttons Depressing the PANLOC buttons will lock the instrument firmly in the installation Depressing the PANLOC buttons a second time as with a ballpoint pen will release the instrument You can then slide the instrument forward to the inspection adjustment position De pressing the inspection adjustment position latches will allow the instrument to be slid completely out of the i
16. to the original per formance limits free of any charge The SERVICE CONTRACT does not cover any ship ping costs to and from the authorized service agency or the factory 2 Any Mcintosh authorized service agency will repair all Mcintosh instruments at normal service rates To receive the free service under the terms of the SERVICE CONTRACT the SERVICE CONTRACT CERTIFICATE must ac company the instrument when taken to the service agency 3 Always have service done by a Mcintosh authorized service agency If the instrument is modified or damaged as a result of un authorized repair the SERVICE CONTRACT will be cancelled Damage by improper use Copyright 1970 By McIntosh Laboratory Inc For your protection Mcintosh selects its dealers carefully Only one dealer in ten qualifies for a Mcintosh franchise To receive the SERVICE CONTRACT your purchase must be made from a Mcintosh franchised dealer Your completely filled in application for a SERVICE CONTRACT must be postmarked within 30 days of the date of purchase of the instrument To receive the SERVICE CONTRACT all in formation on the application must be filled in The SERVICE CONTRACT will be issued when the completely filled in application is received at Mcintosh Laboratory Incor porated in Binghamton New York 5 A Sr OSI Adequate ventilation extends the trouble free life of electronic instruments lt is general
17. ve using the CBS record STR100 Follow these steps to plot the performance of your phonograph cartridge 1 Set the METER RANGE SWITCH to the 20 position 2 Play the 1000 Hz test tone recorded on the CBS Test Record STR100 on your phono graph Turn the LEFT GAIN control until the left meter indicates 0 Turn the RIGHT GAIN control until the right meter indicates Write down the meter indication at each fre quency as the record plays Transfer the readings by frequency to the graph The graph shows the ideal RIAA response curve using the CBS STR1000 test record Compare your curve with the curve on the graph A deviation of 3 dB from the ideal is acceptable By making this check at regular intervals for instance every 6 months any deterioration in the cartridge or system will be quickly detected A tape recorder can be checked in the same fashion 1 Use a standard frequency response tape as the signal source 2 Complete all steps outlined for phono cart ridges 3 You now have a graph of the playback char acteristics of your tape recorder To find the record characteristics of the tape recorder follow this procedure 1 Record the CBS Test Record STR1000 on your tape recorder Adjust the record volume only on the 1000 Hz signal for proper record ing level DO NOT ADJUST THE RECORD VOLUME CONTROL DURING THE RECORD ING 2 Play back the tape just recorded Complete a
Download Pdf Manuals
Related Search