Maytag MET8720DS Installation Guide
Contents
1. If connecting to a 4 wire system This range is manufactured with the ground connected to the neutral by a link The ground must be revised so the green ground wire of the 4 wire power supply cord is connected to the cabinet See Electrical Connection U S A Only section Grounding through the neutral conductor is prohibited for new branch circuit installations 1996 NEC mobile homes and recreational vehicles or an area where local codes prohibit grounding through the neutral conductor When a 4 wire receptacle of NEMA Type 14 50R is used a matching UL listed 4 wire 250 volt 40 or 50 amp range power supply cord pigtail must be used This cord contains 4 copper conductors with ring terminals or open end spade terminals with upturned ends terminating in a NEMA Type 14 50P plug on the supply end The fourth grounding conductor must be identified by a green or green yellow cover and the neutral conductor by a white cover Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft 1 22 m long O UU L 4 wire receptacle 14 50R The minimum conductor sized for the copper 4 wire power cord are 40 amp circuit 2 No 8 conductors 1 No 10 white neutral 1 No 8 green grounding If connecting to a 3 wire system Local codes may permit the use of a UL listed 3 wire 250 volt 40 or 50 amp range power supply cord pigtail This cord contains 3 copper conductors with ring terminals2. Slide range back so rear range foot is under anti tip bracket See installation instructions for details INSTALLATION REQUIREMENTS Gather the required tools and parts before starting installation Read and follow the instructions provided with any tools listed here Tools needed m Tape measure Wrench or pliers Level e nut driver Hand or electric drill m Phillips screwdriver Ye 3 2 mm drill bit Flat blade screwdriver Parts supplied Check that all parts are included m 3 10 32 hex nuts attached to terminal block 3 Terminal lugs Oven racks 2 12 x 1 screws for mounting anti tip bracket Anti tip bracket taped inside upper oven with package containing literature Anti tip bracket must be securely mounted to back wall or floor Thickness of floor may require longer screws to anchor bracket to subfloor Longer screws are available from your local hardware store Parts needed If using a power supply cord m AUL listed power supply cord kit marked for use with ranges The cord should be rated at 250 volts minimum 40 amps or 50 amps that is marked for use with nominal 1 3 5 cm diameter connection opening and must end in ring terminals or open end spade terminals with upturned ends m A UL listed strain relief Check local codes Check existing electrical supply See Electrical Requirements section It is recommended that all electrical connections be made by a licensed quali
3. t d plac e Ne pas faire fonctionner la cuisini re si la bride antibasculement n est pas install e et engag e Le non respect de ces instructions peut causer un d c s ou des br lures graves aux enfants et aux adultes Retirer la bride antibasculement fix e dans le four sup rieur par du ruban adh sif avec le sachet de documentation D terminer la m thode de montage utiliser au plancher ou au mur Pour un plancher en pierre ou en briquetage on peut utiliser la m thode de montage au mur D terminer et marquer l emplacement du bord de la cuisini re dans l espace d couper On peut installer la bride de montage du c t gauche ou droit du d coupage Positionner la bride de montage dans la zone d coup e de fa on ce que le bord droit ou gauche de la bride se trouve 1 6 2 4 cm de l emplacement du bord de la cuisini re tel qu illustr A Bride antibasculement B Marquage de l emplacement du bord de la cuisini re C 1346 2 4 cm 4 Percer deux trous de Ys 3 0 mm qui correspondent aux trous de la bride selon la m thode de montage d termin e Voir ci dessous Montage au plancher Montage au mur A B A Vis n 12 x 15 B Bride antibasculement A Vis n 12 x 1 B Bride antibasculement l aide d un tournevis Phillips monter la bride antibasculement sur le mur ou sur le plancher avec les deux vis n 12 x 1 fournies Plac
4. 4 Connect line 1 black and line 2 red wires to the outer terminal block posts with 10 32 hex nuts Securely tighten hex nuts 6 Replace terminal block access cover a 1 Place the outside of your foot against the bottom front of the oven door to keep the range from moving and grasp the lower right or left side of the control panel as shown NOTE If your countertop is mounted with a backsplash it may be necessary to grasp the range higher than is shown in the illustration 2 Slowly attempt to tilt the range forward If you encounter immediate resistance the range foot is engaged in the anti tip bracket 12 3 If the rear of the range lifts more than Y 1 3 cm off the floor without resistance stop tilting the range and lower it gently back to the floor The range foot is not engaged in the anti tip bracket IMPORTANT If there is a snapping or popping sound when lifting the range the range may not be fully engaged in the bracket Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket Verify that the bracket is held securely in place by the mounting screws 4 Slide the range forward and verify that the anti tip bracket is securely attached to the floor or wall 5 Slide range back so the rear range foot is inserted into the slot of the anti tip bracket IMPORTANT If the back of the range is more than 2 6 1 c
5. d couper dans les placards Ces dimensions constituent les valeurs minimales des d gagements m La bride antibasculement de plancher doit tre install e Pour l installation de la bride antibasculement fournie avec la cuisini re voir la section Installation de la bride antibasculement m Une source d lectricit avec liaison la terre est n cessaire Voir la section Sp cifications lectriques IMPORTANT Afin d viter d endommager les placards consulter le constructeur de la maison ou le fabricant des placards pour d terminer si les mat riaux utilis s peuvent subir un changement de couleur une d stratification ou d autres dommages Cette cuisini re a t con ue conform ment aux exigences des normes UL et CSA International et respecte les temp ratures maximales permises de 194 F 90 C pour les placards en bois R sidence mobile Sp cifications additionnelles respecter lors de l installation L installation de cette cuisini re doit tre conforme aux dispositions de la norme Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 anciennement Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 Lorsque cette norme n est pas applicable l installation doit satisfaire aux criteres de la norme Standard for Manufactured Home Installations ANSI A225 1 NFPA 501A ou aux dispositions des codes locaux Autres crit res a respecter pour une inst
6. riau dur pour viter d endommager le rev tement du sol Si le d placement de la cuisini re est n cessaire pour le nettoyage ou l entretien 1 2 3 4 5 Faire glisser la cuisini re vers l avant D brancher le cordon d alimentation lectrique Effectuer le nettoyage ou l entretien Brancher le cordon lectrique dans une prise de courant reli e la terre Faire glisser de nouveau la cuisini re de fa on ce que le pied arri re de la cuisini re se trouve sous la bride antibasculement Pour v rifier que la bride est bien engag e consulter la section V rifier que la bride anti basculement est bien install e et engag e V rifier que la cuisini re est d aplomb 23 W10430958A 2012 1 12 All rights reserved Printed in U S A Tous droits r serv s Imprim aux E U
7. Add strain relief Direct Wire AWARNING Electrical Shock Hazard Disconnect power before servicing Use 8 gauge copper or 6 gauge aluminum wire Electrically ground range Failure to follow these instructions can result in death fire or electrical shock Style 1 Power supply cord strain relief m Assemble a UL listed strain relief in the opening A UL listed strain relief m Feed the power supply cord through the strain relief in the cord conduit plate on bottom of range Allow enough slack to easily attach the wiring to the terminal block m Tighten strain relief screw against the power supply cord y Style 2 Direct wire strain relief m Use Phillips screwdriver to remove screws and slide cord conduit plate down and out DAR RT m Position cord conduit plate as shown in the following illustration ae Ze LS i TAE A Removable retaining nut B Strain relief m Feed the flexible conduit through the strain relief allowing enough slack to easily attach wiring to the terminal block m Tighten strain relief screw against the flexible conduit FT 5 Replace back panel and screws on rear of range 6 Complete installation following instructions for your type of electrical connection 4 wire recommended 3 wire if 4 wire is not available Electrical Connection Options If your home has 4 wire receptacle NEMA type 14 5
8. les l ments de surface et le four Pour des instructions sp cifiques concernant l utilisation de la cuisini re consulter le Guide d utilisation et d entretien Si la cuisini re ne fonctionne pas contr ler ce qui suit 22 Les fusibles du domicile sont intacts et serr s le disjoncteur n est pas d clench La cuisini re est branch e sur une prise reli e la terre La prise de courant est correctement aliment e Consulter la section D pannage dans le Guide d utilisation et d entretien Apr s 5 minutes de fonctionnement de la cuisini re v rifier la chaleur Si la cuisini re est froide l teindre et contacter un technicien qualifi AVERTISSEMENT Risque de basculement Un enfant ou une personne adulte peut faire basculer la cuisini re ce qui peut causer un d c s Fixer la bride antibasculement au plancher ou au mur conform ment aux instructions d installation Faire glisser de nouveau la cuisini re de fa on ce que le pied arri re de la cuisini re se trouve dans la fente de la bride antibasculement R engager la bride antibasculement si la cuisini re a t d plac e Ne pas faire fonctionner la cuisini re si la bride antibasculement n est pas install e et engag e Le non respect de ces instructions peut causer un d c s ou des br lures graves aux enfants et aux adultes Lorsqu on d place la cuisini re la faire glisser sur une planche de carton ou en mat
9. or open end spade terminals with upturned ends terminating in aNEMA Type 10 50P plug on the supply end Connectors on the appliance end must be provided at the point the power supply cord enters the appliance This uses a 3 wire receptacle of NEMA Type 10 50R 3 wire receptacle 10 50R AWARNING y Electrical Shock Hazard Electrically ground range Failure to do so can result in death fire or electrical shock If codes permit and a separate ground wire is used it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge are in accordance with local codes Be sure that the electrical connection and wire size are adequate and in conformance with CSA Standard C22 1 Canadian Electrical Code Part 1 latest edition and all local codes and ordinances A copy of the above code standards can be obtained from Canadian Standards Association 178 Rexdale Blvd Toronto ON M9W 1R3 CANADA m Check with a qualified electrical installer if you are not sure the range is properly grounded Range Rating Specified Rating of Power Supply Cord Kit and Circuit Protection 120 240 Volts 120 208 Volts Amps 8 8 16 5 KW 7 8 12 5 KW 40 or 50 16 6 22 5 KW 12 6 18 5 KW 50 The NEC calculated load is less than the total connected load listed on the model serial rating plate If connecting to a 50 amp circuit use a 50 amp rated cord with kit For 50 amp rated cord kits
10. to follow these instructions can result in death or serious burns to children and adults When moving range slide range onto cardboard or hardboard to avoid damaging the floor covering If removing the range is necessary for cleaning or maintenance For power supply cord connected ranges 1 Slide range forward Unplug the power supply cord Complete cleaning or maintenance Plug power supply cord into a grounded outlet Slide range back so rear range foot is under anti tip bracket na pp 6 Refer to the Verify Anti Tip Bracket Is Installed and Engaged section to verify engagement 7 Check that range is level For direct wired ranges AWARNING Electrical Shock Hazard Disconnect power before servicing Replace all parts and panels before operating Failure to do so can result in death or electrical shock Disconnect power Slide range forward Complete cleaning or maintenance Slide range back so rear range foot is under anti tip bracket ONZ 5 Refer to the Verify Anti Tip Bracket Is Installed and Engaged section to verify engagement 6 Check that range is level 7 Reconnect power 13 14 15 16 SECURITE DE LA CUISINIERE Votre s curit et celle des autres est tr s importante Nous donnons de nombreux messages de s curit importants dans ce manuel et sur votre appareil m nager Assurez vous de toujours lire tous les messages de s curit et de vous
11. use kits that specify use with a nominal 1 34 9 mm diameter connection opening m A time delay fuse or circuit breaker is recommended This range is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14 50R wall receptacle Be sure the wall receptacle is within reach of range s final location O UU L m Do not use an extension cord INSTALLATION INSTRUCTIONS AWARNING Excessive Weight Hazard Use two or more people to move and install range Failure to do so can result in back or other injury 1 Remove shipping materials tape and film from the range Keep cardboard bottom under range 2 Remove oven racks and parts package from inside oven 3 To place range on its back take 4 cardboard corners from the carton Stack one cardboard corner on top of another Repeat with the other 2 corners Place them lengthwise on the floor behind the range to support the range when it is laid on its back 4 Using 2 or more people firmly grasp the range and gently lay it on its back on the cardboard corners Pull cardboard bottom firmly to remove Use an adjustable wrench to loosen the leveling legs 7 Place cardboard or hardboard in front of range Using 2 or more people stand range back up onto cardboard or hardboard om 1 If range height adjustment is necessary use a wrench or pliers to loosen the 4 leveling legs This may be done with the range on its ba
12. 0R O 1 0 l And you will be connecting to AUL listed 250 volt minimum 40 amp range power supply cord Go to Section 4 wire connection Power supply cord 4 wire direct 5 12 7 cm 3 wire receptacle NEMA type 10 50R 3 wire direct 1 2 5 cm eo A fused disconnect or circuit breaker box A UL listed 250 volt minimum 40 amp range power supply cord A fused disconnect or circuit breaker box 4 wire connection Direct wire 3 wire connection Power supply cord 3 wire connection Direct wire 4 wire connection Power Supply Cord Use this method for m New branch circuit installations 1996 NEC m Mobile homes m Recreational vehicles In an area where local codes prohibit grounding through the neutral Part of metal ground strap must be cut out and removed A Metal ground strap B Discard C Ground link screw 2 Use Phillips screwdriver to remove the ground link screw from the back of the range Save the ground link screw and the end of the ground link under the screw 3 Feed the power supply cord through the strain relief in the cord conduit plate on bottom of range Allow enough slack to easily attach the wiring to the terminal block A Terminal block B Ground link screw C Cord conduit plate D Power supply cord wires 4 Use Phillips screwdriver to connect the green ground wire from the power supply cord to the range with the
13. 4 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 When such standard is not applicable the Standard for Manufactured Home Installations ANSI A225 1 NFPA 501A or with local codes Mobile home installations require m When this range is installed in a mobile home it must be secured to the floor during transit Any method of securing the range is adequate as long as it conforms to the standards listed above m Four wire power supply cord or cable must be used in a mobile home installation The appliance wiring will need to be revised See Electrical Connection section Product Dimensions A 35 K 90 8 cm 0 3 cm cooktop height minimum with leveling legs screwed all D 2872 14 72 4 cm 0 6 cm depth with handle E 26 76 YE 66 4 cm the way in 0 3 cm B Model serial rating plates F 29 e Ye 76 0 cm located behind the control 0 2 cm width panel C 47 119 7 cm 0 3 cm overall height minimum with leveling legs screwed all the way in Range can be raised approximately 1 2 5 cm by adjusting the leveling legs Model serial rating plates may be rotated up from behind the control panel for viewing from the front of the range Excludes handle Dimension given is from wall to front of oven door and will vary based on electric outlet receptacle installation Cabinet Dimen
14. INSTALLATION INSTRUCTIONS FREESTANDING ELECTRIC RANGE WITH DOUBLE OVENS _ INSTRUCTIONS D INSTALLATION POUR CUISINIERE ELECTRIQUE AUTOPORTANTE AVEC FOURS DOUBLES 05 1 Table of Contents Table des mati res RANGE SAFETY sitsinsideisnscssscannsshcacdasscbccedacatestiastndeacseccestnstctacecusnitaceiannce 1 S CURIT DE LA CUISINI RE rune INSTALLATION REQUIREMENTS sas EXIGENCES D INSTALLATION Tools and Parts er gts Outils et pi ces Location Requirements ceeeeee ade Exigences d emplacement Electrical Requirements U S A Only ss Sp cifications lectriques Electrical Requirements Canada Only Fee INSTRUCTIONS D INSTALLATION INSTALLATION INSTRUCTIONG vun vee D ballage de la cuisini re Unpack Range ss s R glage des pieds de nivellement Adjust Leveling Legs it Installation de la bride antibasculement Install Anti Tip Bracket sr V rifier que la bride anti basculement est bien Electrical Connection U S A Only ed de install e et engag e O Verify Anti Tip Bracket Is Installed and Engaged R glage de l aplomb de la cuisini re Level Range id il Achever l installation Complete Installation D placement de la cuisini re Moving the RANGE iii RANGE SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on y
15. a cuisini re a la terre Le non respect de cette instruction peut causer un d c s un incendie ou un choc lectrique Si les codes en vigueur le permettent et qu un conducteur distinct de liaison a la terre est utilis on recommande qu un lectricien qualifie v rifie que la liaison a la terre et la taille du conducteur de liaison a la terre sont ad quates et conformes aux prescriptions a des codes locaux V rifier que le raccordement la source d lectricit et le calibre des conducteurs sont conformes aux prescriptions de la plus r cente dition des normes CSA C22 1 partie 1 Code canadien de l lectricit et de tout code ou r glement local en vigueur Cette cuisini re est dot e d un dispositif de branchement homologation CSA International destin a tre branch sur une prise de courant murale standard 14 50R Veiller a ce que la prise de courant murale soit plac e a port e de la position de service finale de la cuisini re On peut obtenir un exemplaire des normes ci dessus aupres de Canadian Standards Association 178 Rexdale Blvd Toronto ON M9W 1R3 CANADA En cas de doute quant la qualit de la liaison a la terre de la cuisini re consulter un lectricien qualifie O Il L Ne pas utiliser de c ble de rallonge INSTRUCTIONS D INSTALLATION 1 Si un ajustement de la hauteur de la cuisini re est n cessaire A A JERTISSEN A ENT utiliser une cl ou une pince pour dess
16. allation en r sidence mobile m Dans le cas de l installation de cette cuisini re dans une r sidence mobile la cuisini re doit tre fix e au plancher durant tout d placement du v hicule Toute m thode de fixation de la cuisini re est ad quate dans la mesure o elle satisfait aux crit res des normes mentionn es ci dessus m Pour une installation en r sidence mobile un c ble ou cordon d alimentation a quatre fils doit tre utilis Le c blage de appareil devra tre r vis Voir la section Raccordement lectrique 17 Dimensions du produit G E A Hauteur minimale de la table de cuisson avec pieds de nivellement compl tement relev s 3594 16 90 8 cm 0 3 cm B Plaques signal tiques situ es derri re le tableau de commande C Hauteur minimale de la table de cuisson avec pieds de nivellement compl tement relev s 4716 Ye 119 7 cm 0 3 cm D Profondeur avec poign e 2812 1a 72 4 cm 0 6 cm E 26 6 66 4 cm 0 3 cm F Largeur de 29 176 Ye 76 cm 0 2 cm La cuisini re peut amp tre sur lev e d environ 1 2 5 cm en ajustant les pieds de nivellement Il est possible de faire pivoter les plaques signal tiques vers le haut a partir de l arri re du tableau de commande afin qu elles soient visibles depuis l avant de la cuisini re Poign amp e non comprise La dimension fournie correspond
17. cale Pi ces n cessaires En cas d utilisation d un c ble d alimentation lectrique m Cordon d alimentation homologation UL con u pour l utilisation avec une cuisini re Pour service 250 volts minimum 40 A ou 50 A compatible avec une ouverture de diam tre nominal 1 3 5 cm pour le raccordement et avec cosses rondes ou en fourche a pointes relev es l extr mit de chaque conducteur m Unserre c ble homologation UL Consulter les codes locaux V rifier l alimentation lectrique existante Voir la section Sp cifications lectriques Il est recommand de faire r aliser tous les raccordements lectriques par un lectricien qualifi agr IMPORTANT Observer les dispositions de tous les codes et reglements en vigueur m C est l installateur qu incombe la responsabilit de respecter les distances de s paration exig es sp cifi es sur la plaque signal tique de l appareil La plaque signal tique se trouve derri re le tableau de commande m Afin de supprimer le risque de br lures ou d incendie li au fait de se pencher au dessus des plaques de cuisson chaudes les placards de rangement au dessus des plaques doivent tre vit s Si des placards de rangement sont envisag s le risque peut tre r duit par l installation d une hotte de cuisine d passant le bas des placards d au moins 5 12 7 cm horizontalement m Respecter les dimensions indiqu es pour les ouvertures
18. ck or with the range supported on 2 legs after the range has been placed back to a standing position NOTE To place range back up into a standing position put a sheet of cardboard or hardboard in front of range Using 2 or more people stand range back up onto the cardboard or hardboard 2 Adjust the leveling legs to the correct height Leveling legs can be loosened to add up to a maximum of 1 2 5 cm A minimum of 6 5 0 mm is needed to engage the anti tip bracket NOTE If height adjustment is made when range is standing tilt the range back to adjust the front legs then tilt forward to adjust the rear legs When the range is at the correct height check that there is adequate clearance under the range for the anti tip bracket Before sliding range into its final location check that the anti tip bracket will slide under the range and onto the rear leveling leg prior to anti tip bracket installation AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults Remove the anti tip bracket that is taped inside the upper oven with
19. de nivellement arri re se d gage de la bride antibasculement Utiliser une cl pour r gler les pieds de nivellement vers le haut ou vers le bas jusqu ce que la cuisini re soit d aplomb Repousser la cuisini re pour la remettre en place V rifier que le pied de nivellement arri re est engag dans la bride antibasculement REMARQUE La cuisini re doit tre d aplomb pour que les r sultats de cuisson au four soient satisfaisants 21 V rifier que toutes les pieces sont maintenant install es S il reste une pi ce passer en revue les diff rentes tapes pour d couvrir laquelle aurait t oubli e V rifier la pr sence de tous les outils Eliminer recycler tous les mat riaux d emballage V rifier que la cuisini re est d aplomb Voir R glage de aplomb de la cuisini re Utiliser une solution d eau tiede et de nettoyant m nager doux pour liminer tout r sidu de cire laiss par les mat riaux d emballage S cher parfaitement avec un linge doux Pour plus d informations lire la section Entretien de la cuisini re dans le Guide d utilisation et d entretien Lire le Guide d utilisation et d entretien de la cuisini re Brancher le cordon lectrique dans la prise de courant appropri e Faire glisser la cuisini re a son emplacement final V rifier que le c ble flexible ou le cordon lectrique ne sont pas d form s Mettre l appareil sous tension Mettre en marche
20. e cabinet Use a 3 wire UL listed 40 or 50 amp power supply cord pigtail see the following Range Rating chart If local codes do not permit ground through the neutral use a 4 wire power supply cord rated at 250 volts 40 or 50 amps and investigated for use with ranges Specified Rating of Power Supply Cord Kit and Circuit Protection Range Rating 120 240 Volts 120 208 Volts Amps 8 8 16 5 KW 7 8 12 5 KW 40 or 50 16 6 22 5 KW 12 6 18 5 KW 50 The NEC calculated load is less than the total connected load listed on the model serial rating plate If connecting to a 50 amp circuit use a 50 amp rated cord with kit For 50 amp rated cord kits use kits that specify use with a nominal 1 34 9 mm diameter connection opening A circuit breaker is recommended The range can be connected directly to the circuit breaker box or fused disconnect through flexible or nonmetallic sheathed copper or aluminum cable See the Electrical Connection U S A Only section m Allow 2 to 3 ft 61 0 cm to 91 4 cm of slack in the line so that the range can be moved if servicing is ever necessary m AUL listed conduit connector must be provided at each end of the power supply cable at the range and at the junction box m Wire sizes and connections must conform with the rating of the range The wiring diagram is located on the Tech Sheet The Tech Sheet is located on the back of the range inside a clear plastic bag
21. er l ext rieur du pied contre la partie inf rieure avant du tiroir r chaud et saisir le c t inf rieur droit ou gauche du tableau de commande tel qu indiqu REMARQUE Si le plan de travail comporte un dosseret il faudra peut tre saisir la cuisini re plus haut que ce qu indique l illustration Tenter d incliner la cuisini re vers l avant avec pr caution Si vous rencontrez une r sistance imm diate cela signifie que le pied de la cuisini re est engag dans la bride antibasculement 3 Sil arri re de la cuisini re se soul ve de plus de Y 1 3 cm du plancher sans opposer de r sistance cesser d incliner la cuisini re et la reposer doucement sur le plancher Le pied de la cuisini re n est pas engage dans la bride antibasculement IMPORTANT Si l on entend un claquement ou un bruit d clatement lorsqu on soul ve la cuisini re cela signifie peut tre que la cuisini re n est pas bien engag e dans la bride V rifier qu aucune obstruction n emp che la cuisini re de glisser vers le mur ou le pied de la cuisini re de glisser dans la bride V rifier que la bride est fermement maintenue en place par les vis de montage 4 Glisser la cuisini re vers l avant et v rifier que la bride antibasculement est bien fix e au plancher ou au mur 5 Faire glisser de nouveau la cuisini re de fa on ce que le pied arri re de la cuisini re se trouve dans la fente de la bride antibasculement IMPORTANT Si
22. errer les 4 pieds de nivellement Ri id if Ceci doit tre effectu alors que la cuisini re repose sur sa ISque GU poleo ERLERS partie post rieure ou qu elle est soutenue par 2 pieds apr s Utiliser deux ou plus de personnes pour d placer et avoir t replac e en position verticale installer la cuisini re REMARQUE Pour replacer la cuisini re en position verticale Lenon respect d cette instruction peut aude placer un carton ou un panneau de fibres dur devant la P P cuisini re A l aide de deux personnes ou plus relever la une blessure au dos ou d autre blessure cuisini re et la placer sur le carton ou le panneau de fibres dur es sr 2 Ajuster les pieds de nivellement a la hauteur n cessaire Les 1 Oter les mat riaux d emballage le ruban adh sif et le film de la pieds de nivellement peuvent tre desserr s pour ajouter une cuisini re Laisser la base de carton sous la cuisini re hauteur maximale de 1 2 5 cm Un minimum de s 2 Retirer les grilles de four et le sachet de pi ces de l int rieur du 5 0 mm est n cessaire pour engager la bride antibasculement four REMARQUE Si un ajustement de la hauteur est effectu alors 3 Pour placer la cuisini re sur sa partie post rieure sortir les que la cuisini re est debout incliner la cuisini re vers l arri re 4 coins de protection du carton d emballage Empiler l un des pour ajuster les pieds avant puis incliner la cuisini re vers coins sur un autre R p
23. fied electrical installer IMPORTANT Observe all governing codes and ordinances m Itis the installer s responsibility to comply with installation clearances specified on the model serial rating plate The model serial rating plate is located behind the control panel m To eliminate the risk of burns or fire by reaching over heated surface units cabinet storage space located above the surface units should be avoided If cabinet storage is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 12 7 cm beyond the bottom of the cabinets m Cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances m The floor anti tip bracket must be installed To install the anti tip bracket shipped with the range see Install Anti Tip Bracket section m Grounded electrical supply is required See Electrical Requirements section IMPORTANT To avoid damage to your cabinets check with your builder or cabinet supplier to make sure that the materials used will not discolor delaminate or sustain other damage This range has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194 F 90 C Mobile Home Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard Title 2
24. ground link screw The ground wire must be attached first 5 Use nut driver to connect the neutral white wire to the center terminal block post with one of the 10 32 hex nuts A 10 32 hex nut B Ground link screw C Line 1 black D Green ground wire E Neutral center wire F Line 2 red 6 Connect line 1 black and line 2 red wires to the outer terminal block posts with 10 32 hex nuts 7 Securely tighten hex nuts NOTE For power supply cord replacement only use a power cord rated at 250 volts minimum 40 amps or 50 amps that is marked for use with nominal 1 3 5 cm diameter connection opening with ring terminals and marked for use with ranges 8 Replace terminal block access cover 3 wire connection Power Supply Cord Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord 1 Feed the power supply cord through the strain relief in the cord conduit plate on bottom of range Allow enough slack to easily attach the wiring to the terminal block ca IF Wal A Terminal block B Ground link screw C Cord conduit plate D Power supply cord wires 2 5 Use nut driver to connect the neutral white wire to the center terminal block post with one of the 10 32 hex nuts A E A 10 32 hex nut D Neutral white wire B Line 1 black E Line 2 red C Ground link screw Connect line 1 black and line 2 red wires to
25. ibasculement est bien install e et engag e Bride e Faire glisser la cuisini re vers l avant antibasculement V rifier que la bride antibasculement est bien fix e au plancher ou au mur e Faire de nouveau glisser la cuisini re vers l arri re de sorte que le pied de la cuisini re hs er se trouve sous la bride antibasculement Pied de la cuisiniere Voir les instructions d installation pour plus de details EXIGENCES D INSTALLATION Rassembler les outils et composants n cessaires avant d entreprendre l installation Lire et observer les instructions fournies avec chacun des outils de la liste ci dessous Outils n cessaires m Metre ruban m Cl ou pince Niveau m Tourne crou Perceuse manuelle ou lectrique m Foret de 3 2 mm m Tournevis Phillips m Tournevis lame plate Pi ces fournies V rifier que toutes les pi ces sont pr sentes m 3 crous hexagonaux de 10 32 joints au bloc de raccordement 8 attaches de bornes Grilles du four 2 vis n 12 x 1 pour le montage de la bride antibasculement Bride anti basculement fix e par ruban adh sif l int rieur du four sup rieur avec le sachet de documentation La bride antibasculement doit tre bien fix e la cloison arri re ou au plancher L paisseur du plancher peut n cessiter des vis plus longues pour l ancrage de la bride dans le sous plancher Des vis plus longues sont disponibles aupr s de votre quincaillerie lo
26. ires to the outer terminal block posts with 10 32 hex nuts Securely tighten hex nuts Replace terminal block access cover 3 wire connection Direct Wire Use this method only if local codes permit connecting ground conductor to neutral supply wire 1 Pull the conduit through the hole and conduit plate on bottom of range Allow enough slack to easily attach the wiring to the terminal block A B C r A Terminal block D Line 2 red wire B Ground link screw E Bare green ground wire C Cord conduit plate F Line 1 black wire 2 Attach terminal lugs to line 1 black bare green ground and line 2 red wires Loosen do not remove the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs Securely tighten setscrew to XX Ibs in torque See Bare Wire Torque Specifications chart A P Ce Ue j C D E A Terminal lug B Setscrew C Line 1 black wire D Bare green ground wire E Line 2 red wire 11 Bare Wire Torque Specifications Attaching terminal lugs to the terminal block 20 Ibs in 2 3 N m Wire Awg Torque 8 gauge copper 25 lbs in 2 8 N m 6 gauge aluminum 35 Ibs in 4 0 N m 3 Use nut driver to connect the bare green ground wire to the center terminal block post with one of the 10 32 hex nuts A 10 32 hex nut B Line 1 black C Ground link screw D Bare green ground wire E Line 2 red F Terminal lug
27. it through the strain relief on cord conduit plate on bottom of range Allow enough slack to easily attach wiring to the terminal block B ee este C G A Terminal block E Neutral white wire B Ground link screw F Line 1 black wire C Cord conduit plate G Bare green ground wire D Line 2 red wire Attach terminal lugs to line 1 black neutral white and line 2 red wires Loosen do not remove the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs Securely tighten setscrew to XX Ibs in torque See Bare Wire Torque Specifications chart A je La Oe C D E A Terminal lug B Setscrew C Line 1 black wire D Neutral white wire E Line 2 red wire Bare Wire Torque Specifications Attaching terminal lugs to the terminal block 20 Ibs in 2 3 N m Wire Awg Torque 8 gauge copper 25 lbs in 2 8 N m 5 6 gauge aluminum 35 Ibs in 4 0 N m Use Phillips screwdriver to connect the bare green ground wire to the range with the ground link screw The ground wire must be attached first and must not contact any other terminal Use nut driver to connect the neutral white wire to the center terminal block post with one of the 10 32 hex nuts A 10 32 hex nut E Neutral white wire B Line 1 black F Line 2 red C Bare green ground wire G Terminal lug D Ground link screw Connect line 1 black and line 2 red w
28. l arri re de la cuisini re se trouve plus de 2 5 1 cm du mur de montage cela signifie que le pied arri re de la cuisini re n est peut tre pas engag dans la bride Glisser la cuisini re vers l avant et d terminer si un objet fait obstruction entre la cuisini re et la paroi de montage Pour assistance ou d pannage consulter la section Assistance ou Service du guide d utilisation et d entretien la couverture ou la section Garantie des instructions d utilisation pour obtenir les coordonn es des personnes contacter 6 R p ter les tapes 1 et 2 pour s assurer que le pied de la cuisini re est bien engag dans la bride antibasculement Si l arri re de la cuisini re se soul ve de plus de 1 2 1 3 cm du plancher sans opposer de r sistance cela peut signifier que la bride antibasculement n est pas correctement install e Ne pas faire fonctionner la cuisini re si la bride antibasculement n est pas install e et engag e Consulter la section Assistance ou Service du guide d utilisation et d entretien la couverture ou la section Garantie des instructions d utilisation pour pouvoir contacter un service de d pannage N a Placer une grille dans le four Placer un niveau sur la grille et contr ler l aplomb de la cuisini re d abord transversalement puis dans le sens avant arri re Si la cuisini re n est pas d aplomb la tirer de nouveau pour que le pied
29. la distance du mur l avant de la porte du four et varie en fonction de l installation de la prise lectrique murale 18 Dimensions du placard Les dimensions de l espace d installation entre les placards sont valides pour l installation entre des placards de 24 61 0 cm de profondeur avec plan de travail de 25 63 5 cm de profondeur et 36 91 4 cm de hauteur IMPORTANT En cas d installation d une hotte ou d un ensemble hotte micro ondes au dessus de la cuisini re suivre les instructions fournies avec la hotte concernant les dimensions de d gagement respecter au dessus de la surface de la table de cuisson Une cuisini re autoportante peut tre install e sans aucun d gagement proximit de parois combustibles Pr I l l lL lt N N N Be A 18 45 7 cm entre le placard superieur et le plan de travail B Profondeur des placards superieurs 13 33 0 cm C Largeur de l ouverture 30 76 2 cm min F La porte ou charniere du placard ne doit pas d passer a l int rieur de l ouverture G 1 3 8 cm min depuis le placard de droite H 2 8 1 cm min depuis le D Pour la distance libre plancher minimale vers la partie 1 7 17 8 cm min depuis le sup rieure de la table de plancher cuisson voir la REMARQUE E Largeur de l ouverture 30 76 2 cm min J 8 20 3 cm de largeur K 3Y2 8 91 cm min depuis le plancher Position correcte de la prise il
30. lustr e ci dessus Aucun l ment situ dans les zones gris es ne doit d passer de plus de 1 3 8 cm depuis le mur sans quoi la cuisini re ne glissera pas jusqu au fond REMARQUE Distance de s paration minimale de 24 61 cm lorsque le fond d un placard de bois ou de m tal est prot g par une planche ignifug e d au moins 4 0 64 cm recouverte d une feuille m tallique d paisseur gale ou sup rieure a acier calibre 28 MSG acier inoxydable 0 015 0 4 mm aluminium 0 024 0 6 mm ou cuivre 0 020 0 5 mm Distance de s paration de 30 76 2 cm ou plus entre le dessus de la table de cuisson et le fond d un placard de bois ou de m tal non prot g Intensit nominale sp cifi e du cordon d alimentation et de la Sp cifications lectriques pour la cuisini re A AVERTISSEMENT protection du circuit wy 120 240 volts 120 208 volts Amp res 88 165KW 78 125KW 40 ou 50 16 6 22 5 KW 12 6 18 5 KW 50 Risque de choc lectrique La charge NEC calcul e est inf rieure a la charge totale connect e indiqu e sur la plaque signal tique En cas de raccordement a un circuit de 50 A utiliser un cordon de 50 A nominaux avec son ensemble Pour les cordons de 50 A nominaux utiliser des ensembles qui sp cifient une utilisation avec une ouverture pour le raccordement d un diametre nominal de 1 34 9 mm m Onrecommande l emploi de fusibles temporis s ou disjoncteurs Relier l
31. m from the mounting wall the rear range foot may not engage the bracket Slide the range forward and determine if there is an obstruction between the range and the mounting wall If you need assistance or service refer to the Assistance or Service section of the Use and Care Guide or the cover or Warranty section of the User Instructions for contact information 6 Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti tip bracket If the rear of the range lifts more than 1 2 1 3 cm off the floor without resistance the anti tip bracket may not be installed correctly Do not operate the range without anti tip bracket installed and engaged Please reference the Assistance or Service section of the Use and Care Guide or the cover or Warranty section of the User Instructions to contact service Place a rack in oven Place level on rack and check levelness of range first side to side then front to back pO 3 If range is not level pull range forward until rear leveling leg is removed from the anti tip bracket 4 Use wrench to adjust leveling legs up or down until range is level Push range back into position 5 Check that rear leveling leg is engaged in anti tip bracket NOTE Range must be level for satisfactory baking performance _ Check that all parts are now installed If there is an extra part go back through the steps to see which step
32. our appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean You can be killed or seriously injured if you don t immediately A DANGER follow instructions You can be killed or seriously injured if you don t follow A WARN l N G instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed IMPORTANT Save for local electrical inspector s use IMPORTANT conserver pour consultation par l inspecteur local des installations lectriques W10430958A AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults To verify the anti tip bracket is installed and engaged Anti Tip e Slide range forward LL Bracket Look for the anti tip bracket securely attached to floor or wall
33. sions Cabinet opening dimensions shown are for 25 63 5 cm countertop depth 24 61 0 cm base cabinet depth and 36 91 4 cm countertop height IMPORTANT If installing a range hood or microwave hood combination above the range follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface A freestanding range may be installed next to combustible walls with zero clearance F Cabinet door or hinge should not extend into cutout G 1 3 8 cm min from right side cabinet H 2 8 1 cm min from floor 1 7 17 8 cm min from floor J 8 20 3 cm width K 372 8 91 cm min from floor A 18 45 7 cm upper cabinet to countertop B 13 33 0 cm upper cabinet depth C 30 76 2 cm min opening width D For minimum clearance to the top of the cooktop see NOTE E 30 76 2 cm min opening width Proper positioning of outlet shown above Nothing located in shaded areas can extend more than 172 3 8 cm from wall or range will not slide all the way back NOTE 24 61 0 cm minimum when bottom of wood or metal cabinet is covered by not less than Y4 0 64 cm flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 0 4 mm stainless steel 0 024 0 6 mm aluminum or 0 020 0 5 mm copper 30 76 2 cm minimum clearance between the top of the cooking platform and the bottom of an unprotected wood or me
34. tal cabinet If codes permit and a separate ground wire is used it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes Do not use an extension cord Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances A copy of the above code standards can be obtained from National Fire Protection Association 1 Batterymarch Park Quincy MA 02169 7471 WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded Do not modify the power supply cord plug If it will not fit the outlet have a proper outlet installed by a qualified electrician Electrical Connection To properly install your range you must determine the type of electrical connection you will be using and follow the instructions provided for it here m Range must be connected to the proper electrical voltage and frequency as specified on the model serial number rating plate The model serial rating plate is located behind the control panel Refer to the figures in Product Dimensions in the Location Requirements section m This range is manufactured with the neutral terminal connected to th
35. ter avec les 2 autres coins Les l avant pour ajuster les pieds arri re an a a or a 3 Lorsque la cuisini re est la hauteur souhait e v rifier qu il y a sursa partie en a q un espace suffisant sous la cuisini re pour loger la bride en p p a antibasculement Avant de faire glisser la cuisini re a son 4 l aide de deux personnes ou plus saisir fermement la emplacement final v rifier qu il sera possible de faire glisser la cuisini re et la poser d licatement sur sa partie posterieure sur bride antibasculement sous la cuisiniere et sur le pied de les coins de protection nivellement arri re avant l installation de la bride 5 Tirer fermement sur la partie inferieure du carton pour le retirer antibasculement 6 Utiliser une cl molette pour desserrer les pieds de nivellement 7 Placer le carton ou le panneau de fibres dur devant la cuisini re l aide de deux personnes ou plus relever la cuisini re et la placer sur le carton ou sur le panneau de fibres dur 19 20 A AVERTISSEMENT Risque de basculement Un enfant ou une personne adulte peut faire basculer la cuisini re ce qui peut causer un d c s Fixer la bride antibasculement au plancher ou au mur conform ment aux instructions d installation Faire glisser de nouveau la cuisini re de fa on ce que le pied arri re de la cuisini re se trouve dans la fente de la bride antibasculement R engager la bride antibasculement si la cuisini re a
36. the outer terminal block posts with 10 32 hex nuts Securely tighten hex nuts NOTE For power supply cord replacement only use a power cord rated at 250 volts minimum 40 amps or 50 amps that is marked for use with nominal 1 3 5 cm diameter connection opening with ring terminals and marked for use with ranges Replace terminal block access cover Direct Wire Installation Copper or Aluminum Wire This range may be connected directly to the fuse disconnect or circuit breaker box Depending on your electrical supply make the required 3 wire or 4 wire connection 1 10 Strip outer covering back 3 7 6 cm to expose wires Strip the insulation back 1 2 5 cm from the end of each wire 1 2 5 gt er Ls 7 6 cm Allow enough slack in the wire to easily attach the wiring terminal block Complete electrical connection according to your type of electrical supply 4 wire or 3 wire connection 4 wire Connection Direct Wire Use this method for m New branch circuit installations 1996 NEC m Mobile homes m Recreational vehicles E In an area where local codes prohibit grounding through the neutral _ Part of metal ground strap must be cut out and removed A Metal ground strap B Discard C Ground link screw 2 Use Phillips screwdriver to remove the ground link screw from the back of the range Save the ground link screw and the end of the ground link under the screw 3 Pull the condu
37. the package containing literature Determine which mounting method to use floor or wall If you have a stone or masonry floor you can use the wall mounting method 3 Determine and mark edge of range in the cutout space The mounting bracket can be installed on either the left side or right side of the cutout Position mounting bracket in cutout so that right or left edge of the bracket is 1 6 2 4 cm from the marked edge of the range as shown A Anti tip bracket B Mark edge of range C 6 2 4 cm 4 Drill two Ys 3 0 mm holes that correspond to the bracket holes of the determined mounting method See the following Floor Mounting Wall Mounting A 12 x 1 screws A 12 x 1 screws B Anti tip bracket B Anti tip bracket 5 Using a Phillips screwdriver mount anti tip bracket to the wall or floor with the two 12 x 1 screws provided Power Supply Cord AWARNING y Electrical Shock Hazard Disconnect power before servicing Use a new 40 amp power supply cord Plug into a grounded outlet Failure to follow these instructions can result in death fire or electrical shock _ Disconnect power 2 Use Phillips screwdriver to remove the terminal block cover screw located on the back of the range Pull cover down and toward you to remove cover 3 Remove plastic tag holding three 10 32 hex nuts from the middle post of the terminal block 4
38. was skipped Check that you have all of your tools Dispose of recycle all packaging materials Check that the range is level See Level Range Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by shipping material Dry thoroughly with a soft cloth For more information read the Range Care section of the Use and Care Guide Read the range Use and Care Guide 7 Plug power cord into appropriate outlet Slide range into its final location Check that the flexible conduit or power supply cord are not bent 8 Turn power on Turn on surface elements and oven See the Use and Care Guide for specific instruction on range operation If range does not operate check the following m Household fuse is intact and tight or circuit breaker has not tripped RN gt Range is plugged into a grounded outlet Electrical supply is connected See Troubleshooting in the Use and Care Guide When the range has been on for 5 minutes check for heat If range is cold turn off the range and contact a qualified technician AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure
39. y conformer Voici le symbole d alerte de s curit Ce symbole d alerte de s curit vous signale les dangers potentiels de d c s et de blessures graves a vous et a d autres Tous les messages de s curit suivront le symbole d alerte de s curit et le mot DANGER ou AVERTISSEMENT Ces mots signifient Risque possible de deces ou de blessure grave si vous ne A DAN G E R suivez pas imm diatement les instructions Risque possible de d c s ou de blessure grave si vous A AVERTISSEM ENT ne suivez pas les instructions Tous les messages de s curit vous diront quel est le danger potentiel et vous disent comment r duire le risque de blessure et ce qui peut se produire en cas de non respect des instructions A AVERTISSEMENT Risque de basculement Un enfant ou une personne adulte peut faire basculer la cuisini re ce qui peut causer un d c s Fixer la bride antibasculement au plancher ou au mur conform ment aux instructions d installation Faire glisser de nouveau la cuisini re de fa on ce que le pied arri re de la cuisini re se trouve dans la fente de la bride antibasculement R engager la bride antibasculement si la cuisini re a t d plac e Ne pas faire fonctionner la cuisini re si la bride antibasculement n est pas install e et engag e Le non respect de ces instructions peut causer un d c s ou des br lures graves aux enfants et aux adultes Pour v rifier que la bride ant
Download Pdf Manuals
Related Search