Maytag Agility F6212901 User's Manual
Contents
1. agility Deep Cleaner Your AGILITY Deep Cleaner is fully assembled d an ready to begin cleaning www maytag co uk Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING APPLIANCE WAR N i N G m To reduce the risk of fire electric E shock or injury Use indoors only Use only on surfaces moistened by the cleaning process Do not immerse product Connect to a properly earthed source using the factory fitted plug and cable only Do not clean over floor electrical outlets Do not use without tanks in place Use extra care when cleaning on stairs Do not place deep cleaner on stairs Use deep cleaner only for its intended use as described in the instructions Use only attachments supplied or recommended The use of an extension cord is not recommended Unplug deep cleaner when not in use Turn off all controls before unplugging Unplug deep cleaner before connecting the powered hand tool Always disconnect cable from electrical source before servicing the deep cleaner Do not unplug by pulling on cable To unplug grasp the plug not the cable Never handle plug or appliance with wet hands Do not pull or carry by cable use cable as a handle close door on cable or pull cable around r sharp edges or corners Do not run appliance over cable Keep cable away trom heated surfaces Do not use with damaged cable or p2. press to release cleaning solution Clean Surge button Upper handle Upper handle release button Solution tank cap measuring cup Solution tank release button Solution tank Brush setting selector Nozzle Recovery tank Recovery tank release button Powered hand tool Recovery tank cap Stair upholstery nozzle Cable hooks tool caddy removed Hose door Handle release pedal ON OFF pedal Hose Cable hooks tool caddy stored on cleaner Hose connector Tool caddy SASS PS KLE TL THe ne Cott em Y FN fi This deep cleaner is intended for household use Operate deep cleaner only at voltage specified on data plate on back of cleaner Plug deep cleaner into a properly earthed source Your AGILITY Unfold handle How to fold handle Deep Cleaner is fully assembled and ready to begin cleaning Raise upper handle A to Press upper handle release upright position until it button B to fold handle locks in place Deep Cleaner Basics Fill the solution tank SS LS WW Cte Kw Unplug deep cleaner from electrical source Y Press button A and remove solution tank Fig 3 l g VY Release latches B on tank cap and remove Fig 4 PIES UI Y Use cap Fig 5 to measure the proper amount of detergent according to the chart below Amount of Surface detergent Type of detergent Carpet two Carpet caps Upholstery Detergent Uph
3. al seconds A Do not press trigger Fig 20 vy Turn deep cleaner off and unplug it Y Hold hose connector in sink and press trigger to remove solution from hose B Fig 20 Store hose Unplug deep cleaner from electrical source gt Hook hose connector C into caddy Fig 21 gt Wrap hose around caddy in a anticlockwise direction Fig 22 gt Hook tool connector D and SpinScrub tool E onto caddy Fig 23 gt Snap upholstery tool F into caddy Fig 24 Vd we Hose caddy You can either store the hose caddy on the cleaner or remove it to store separately To store caddy on the cleaner Slide tabs G on caddy into slots on back of cleaner Fig 25 gt Hook top of caddy to cleaner H gt rap cable around cable hooks I on caddy Fig 26 Rotate top hook to release cable To remove caddy from the cleaner Lift caddy off cleaner Fig 27 gt Wrap cable around cable hooks J on back of cleaner Fig 28 Rotate bottom hook to release cable Brush speed selector Choose ON for normal cleaning of carpet Choose OFF when brushing is not desired Clean Surge button Push Clean Surge button K to release extra cleaning solution Use the Clean Surge button when cleaning heavily soiled areas of carpet traffic areas spots etc No cleaning solution removes all stains from all carpets Stain removal varies with the type of spill time
4. er brands may damage the cleaner Clean the carpet or upholstery e Squeeze and hold trigger Move cleaner forward and back e Release trigger and go over same area to pick up dirty solution Use additional dry strokes to remove more dirty solution e Tough spots and stains may need additional treatment with Spot and Stain Spray Listen carefully When the motor sound rises in pitch or changes the recovery tank needs to be emptied When the recovery tank is full the cleaner will no longer pick up dirty solution Allow time for the eel a or upholstery to dry Avoid walking on carpet or using upholstery until it is completely dry When carpet and or upholstery are dry vacuum one more time MAYTAG and ANN are registered trademarks 1 05 F6212901 Printed in USA 56518181
5. h cleaner over same area to pick up dirty solution without putting down more solution Continue using dry strokes until you see only a little solution coming up through the nozzle front of i aa Do not make the carpet too wet Use no more than two sets of forward and backward strokes while releasing solution Always follow with dry strokes the more the better Listen carefully When the motor sound changes rises in pitch the recovery tank needs to be emptied When water has reached the full line in the recovery tank the cleaner will NOT pick up any more dirty solution Allow carpet to dry Avoid walking on the carpet until it is dry Increased air circulation open doors turn on fans etc will help carpet dry thoroughly Vacuum thoroughly after carpet has dried This will reduce any shading left by the deep cleaner s brushes Cleaning upholstery 1 10 11 12 Check fabric cleaning code Fig 36 The codes indicate whether it is alright to use your deep cleaner to clean the upholstery Do not use the deep cleaner on upholstery marked Dry Clean Only If you are unsure please refer to the original manufacturer Vacuum upholstery thoroughly with your vacuum cleaner s attachments Test detergent for colorfastness on a hidden area of upholstery Wet a white cloth or paper towel with some detergent Gently rub onto a hidden area of upholstery Wait ten minutes Blot with white cloth or paper towel and chec
6. ion remaining inside the cleaner V Empty recovery tank rinse thoroughly and let air dry Y Allow brushes and underside of deep cleaner to air dry thoroughly before storing deep cleaner on a carpeted or wood surface Lubrication The motor is e de with bearings which contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Do not add lubricant to motor bearings Continued gt 13 Troubleshooting and Service Use the list below to help solve minor problems What s the What to do problem Deep cleaner won t run V Make sure the cleaner is plugged in firmly V Check the fuse Low suction V Empty the recovery tank it may be full and the automatic shut off engaged V Make sure recovery tank cap is securely latched Cleaning solution won t VY Make sure solution tank is securely in place dispense V Refill the solution tank if it is empty Brushes won t rotate vV Clean brush filter as described in Fig 45 V Set Brush Speed Selector to ON Low suction in hose during v Make sure recovery tank cap tool use is securely tool use latched V Disconnect hose from cleaner and check for block age in hose If the fault is something that you cannot correct yourself please contact e 01737 231000 our Consumer Response Centre QAM 5PM Monday Friday e ukservice maytag com IMPORTANT Cord Replacement This MAYTAG appliance is supplied complete with a plug If the
7. k for color transfer Pretreat spots and stains with MAYTAG Spot and Stain Spray Fig 37 Spray spot or area with Spot and Stain Spray Then proceed with the next cleaning steps Fill solution tank with hot tap water and proper amount of MAYTAG deter gent see page 5 Fig 38 Use only MAYTAG brand detergents in your deep cleaner Other brands may damage the deep cleaner Attach hose and tool as described in Figs 13 19 Fig 39 Place handle in full upright position Turn cleaner ON Squeeze and hold trigger A to release cleaning solution Gently press tool into fabric and slowly pull the tool over the fabric Fig 40 Let go of trigger and pull tool over same area to pick up dirty solution with out putting down more solution Continue ae dry strokes until you see only a little solution coming up through the tool Do not make the ip eee too wet Use no more than two strokes while releasing solution Always follow with dry strokes the more the better Listen carefully When the motor sound changes rises in pitch the recovery tank needs to be emptied When water has reached the full line in the recovery tank the cleaner will NOT pick up any more dirty solution Allow upholstery to dry Avoid using upholstery until it is dry Increased air circulation open doors turn on fans etc will help upholstery dry thoroughly Continued 2 11 Routine care for your Deep Cleaner Clean the nozzle Unplug deep c
8. leaner from electrical source gt Remove solution and recovery tanks to prevent possible leaks Lift up on top of nozzle A and slide off cleaner Fig 41 Wipe debris off nozzle and front of cleaner with a damp cloth gt Tilt cleaner back raising front of cleaner off floor Slide nozzle B up from bottom of cleaner Fig 42 Press on upper portion of nozzle to snap in place Clean the brushes Unplug deep cleaner from electrical source gt Remove solution and recovery tanks to prevent possible leaks Tilt cleaner back so handle rests on the floor gt Pull brush assembly firmly to remove Fig 43 Rinse brushes under running water gt Align posts C on brush assembly with slots D in cleaner Fig 44 Turn brushes slightly to align square post E with square hole F in cleaner Fig 44 Press brush assembly firmly and snap in place Clean the brush filter Unplug deep cleaner from electrical source gt oe solution and recovery tanks to prevent possible eaks Tilt cleaner back so handle rests on the floor gt Squeeze filter frame G and pull it out until it stops Fig 45 gt Wipe debris off filter Slide filter back into place Storing your Deep Cleaner Y Empty solution tank and rinse thoroughly v V Place empty solution tank on deep cleaner Turn deep cleaner ON Squeeze trigger and push deep cleaner forward and back several times This will clear any solut
9. lug If appliance is not working as it should please refer to Trouble Shooting Do not point tools toward people or pets Keep detergents and other cleaners out of children s reach Do not use to pick up flammable or combustible liquids or use in areas where they may be present Avoid picking up hard sharp objects with the deep cleaner They may damage the machine Keep hair loose clothing fingers feet and all parts of body away from openings and moving parts Store in a dry place Do not expose machine to freezing temperatures Save these instructions To contact us e www maytag co uk e 01737 231000 our Consumer Response Centre 9 AM to 5 PM Monday Friday e ukservice maytag com Fill in and Save For your records enter the model number and serial numbers in the spaces provided These numbers are located on the data label on the underside of the cleaner Model No Serial No Save your sales receipt and attach it to this manual Proof of date of purchase may be required for the guarantee Unpacking Contents A Deep cleaner B Detergent Important safeguards Unpacking Cleaner description Deep cleaner basics Filling the tank Emptying the recovery tank 6 Attaching the hose 7 Selecting amp attaching tool 7 Draining amp storing hose 8 i Dis Lp M 5 a K K K CI Continued 2 3 Cleaner Description Features Hand grip Solution trigger
10. main cord of this appliance is damaged the appliance must be repaired by an Authorised Maytag Repairer to avoid safety hazard Guarantee The 2 year guarantee on your AGILITY Deep Cleaner becomes effective from your date of purchase We suggest you record the model and serial number from the information plate on your AGILITY Deep Cleaner and retain it with your original proof of purchase This guarantee covers all materials and manufacturer assembly of your AGILITY Deep Cleaner All repairs must be authorised in advance by our Consumer Response Centre and subsequently completed by an authorised agent Any repair completed under guarantee will not extend the original period of your product guarantee This guarantee applies to normal domestic use only This guarantee does not cover normal wear and tear negligence misuse accidental damage blockages or consumable items This guarantee does not cover any consequential loss These guarantee benefits are in additional to your statutory rights 14 15 Basic steps for cleaning Vacuum carpet thoroughly to remove loose dirt Test detergent for colorfastness on a hidden area of carpet or upholstery Pretreat spots stains and high traffic areas with MAYTAG Spot and Stain Spray Blot spots or stains to remove as much of the spot as possible Fill solution tank with hot tap water and proper amount of MAYTAG detergent Use only MAYTAG brand detergents in your deep cleaner Oth
11. olstery one Carpet cap Upholstery Detergent NOTE For best results use only MAYTAG detergents They are specifically formulated for use with your AGILITY Deep Cleaner Y Pour detergent into tank vV Fill tank to fill line C approx 4 litres with hot tap water Fig 6 V Replace cap Secure both latches B Fig 4 vy Place bottom of tank onto cleaner Pivot top of tank and snap in place Fig 7 Caution Detergents contain Anionic and Nonionic Surfactants Avoid contact with the eyes and skin In case of contact with eyes flush with cold water for 15 minutes In case of contact with skin wash with water If irritation persists refer to your GP Continued gt 5 Empty the recovery tank SS MNE Unplug deep cleaner from electrical source LSA _ Y An automatic shut off device prevents the cleaner from picking up more dirty water than it can hold in the recovery tank You will know the tank needs to be emptied e The amount of dirty water has reached the full line e When the motor sound rises in pitch e You do not see dirty solution coming up through the nozzle e The float B inside the recovery tank has risen to the top of the tank Fig 8 VY Press button C and remove tank Fig 9 VY Release latches D on tank cap and remove cap Fig 10 V Empty tank VY Replace cap Fig 11 Secure both latches D Fig 10 For full suction it is important that the recove
12. passed before removal carpet material and carpet type Continued 2 9 10 Cleaning carpet 1 10 11 12 13 Remove lightweight furniture tables lamps etc from area to be cleaned Protect any remaining furniture by pinning up furniture skirts and placing aluminium foil or plastic under legs Vacuum carpet thoroughly to remove loose dirt hair lint and other debris Fig 31 Test detergent for colorfastness on a hidden area of carpet Wet a white cloth or paper towel with some detergent Gently rub onto a hidden area of carpet Wait ten minutes Blot with white cloth or paper towel and check for color transfer Pretreat spots stains and high traffic areas with MAYTAG Spot and Stain Spray Fig 32 Spray spot or area with Spot and Stain Spray Then proceed with the next cleaning steps Fill solution tank with hot tap water and proper amount of MAYTAG detergent see page 5 Fig 33 Use only MAYTAG brand detergents in your deep cleaner Other brands may damage the deep cleaner Plan your cleaning to avoid walking on wet carpet Start at the end of the room farthest from the exit and work in small sections Fig 34 Step on handle release pedal and lower handle Turn cleaner ON Squeeze and hold trigger A to release cleaning solution Fig 35 Push cleaner forward SLOWLY then pull it back SLOWLY Use Clean Surge button B in heavily soiled areas Fig 35 Let go of trigger and pus
13. ry tank cap is properly secured before cleaning Y Remove 7 debris that has collected on lint filter E on cleaner body Fig 12 and inset V Place bottom of tank onto cleaner Pivot top of tank and snap in place Fig 12 Attach the hose Unplug deep cleaner from electrical source VY Place handle in upright position VY The hose and tool caddy can be removed from the cleaner if you desire Y Remove hose from tool caddy V Open hose door A on back of deep cleaner Fig 13 Y Align hose connector with hose and solution ports C Vas e E O Y Push hose into port and lock in place ZN N Ly vy To remove hose Squeeze latches D on top and bottom of hose Remove hose from port Fig 15 V Close hose door A tightly inset Select tool 16 17 SpinScrub hand tool Stair Upholstery nozzle e Rotating brushes e Built in brush e Use on carpet to clean e Use on upholstery spots small areas or stairs Attach tool Unplug deep cleaner from electrical source Y Slide tool onto hose Snap tool over tab E on hose Fig 18 vy To remove tool Push forward and up on latch F Fig 19 Slide tool off hose Continued 7 The handle must be in the upright position in order to get cleaning solution through the hose Drain the hose When finished using the hose and tool remove water from the hose v Turn deep cleaner on and hold end of hose up for sever
Download Pdf Manuals
Related Search