Marshall electronic V-LCD15SB-AFHD-DT User's Manual
Contents
1. Os Adjust the Contrast knob until an even grayscale appears along the top bars 6 Disable Monochrome mode 7 Enable Blue Only mode and adjust the Color knob so that the outermost bars white and blue appear to match in brightness 8 Composite S Video NTSC only Adjust the Tint knob until the third bar from the left cyan and the third bar from the right magenta appear to match in brightness 9 Disable Blue Only mode mE Pixel to Pixel Mode Use this setting to enable Pixel to Pixel mode This mode bypasses the monitor s internal scaling function and displays incoming images in their native resolution and aspect ratio with a one to one mapping e For incoming formats smaller than the native resolution of the LCD panel 1024 x 768 the image will be displayed in the center of the screen using only the necessary LCD pixels For example NTSC or PAL images will occupy exactly 720 x 486 or 720 x 576 pixels respectively The surrounding pixels will be black For incoming formats exceeding 1024 x 768 pixels only the center 1024 x 768 of the incoming image will displayed occupying the whole screen with the remainder of the picture cropped For example 1080 and 720 formats will both be cropped to 1024 x 768 and displayed full screen Note Pixel to Pixel mode will utilize the entire screen 1024 x 768 regardless of the aspect ratio setting Pixel to Pixel mode is not available when using the VGA or DVI inputs 12 Fron2. e we Right Front Panel Top Front Panel Rear Panel Features ELECO PELEPECOC REO COCOSECCOCOSEOCOICPEOCEOLEIC mm mm y POWER 12VDC 3 0A Marshall Electronics Inc CE py Made in the USA COMPONENT A Pb Pr GER FAS IN SDI OUT Power Input Connect the 12VDC input to the Conxall 2 pin twist lock power input connector Power can be supplied from the included power supply or from a variety of DC sources supplying at least 3 Amps at 12 Volts IMPORTANT If using a power source other than the included power supply be sure that the polarity of the DC input is correct Pin 1 12VDC Pin2 GND Signal Input Output Connections Composite Video Input Output BNC S Video Input Output 4 Pin Mini DIN YPgPn Input Output BNC x 3 SDI Input Output BNC VGA HD 15 DVI 29 Pin connector DVI D signals only All outputs are active and require the monitor to be powered Rear Panel Tally Interface Each tally light is activated via the HD 15 connector by connecting the corresponding pin to ground A variety of external devices can be used to perform the contact closure No additional power should be supplied to the HD 15 port Tally Interface HD 15 Pinout Example To activate the red tally light connect pin 2 to pin 4 5 14 or 15 Mounting Holes A VESA standard 75 mm hole pattern is provided to accom
3. EO e AICHE E Supports ITU R BT 656 SMPTE 259M 292M MAIN MENU AND NAVIGATION nella 8 VGA Input IM ee MARKER SETUP SUBMENU outra a canas 9 Supports RGBHV RsGsBs RGsB RGB CS Dimensions wx h xd 15 25 x 10 45 x 1 77 TO A e o il ia 9 Height with Stand 11 01 AS MaK A A O ea ee 10 DVI Input 7 Rack Height 6 RU Marker Baco een eae an ene ee ee a een ee eee ee eee eee 10 Supports Digital Signals Only DVI D Additional Mounting VESA 75 mm Cener MaRe sree seat ee sede eae fe cto te ate fet ge tad tet 10 HDCP Supported VIDEO CONFIGURATION SUBIVIEIN Ulsa iia 11 Weight Monitor Only 8 1 lbs Color Temperature PreselS dal lala deleita 11 Operating Temperature 32 F to 120 F 0 C to 50 C Adjusting Color Blas eiii ii 11 CONNECTORS Storage Temperature 4 F to120 F 20 C to 50 C ra N PE AEE eta Seton A nn A AS Video Input Gomoliands FCC Class A ANSI 63 4 a Le Video 1 x BNC Female 75 Q Certificates on file SMe casei ono niche cheb E cas ca edecect ea ted adnan S Video Y C 1 x 4 Pin Mini DIN Pixel to Pixel Mode A O 12 YPePa 3 x BNC Female 75 Q RoHs Do not dispose Return to Aspect Ratio Setting ccccccccccsecccseeeeceescesceaeecceneecceneeccesesccasencouneecsecesaeeesseseesseneecsedeessaeessesesccaneecoasescoesess 13 HD SDI 1 x BNC Female 75 Q Manufacturer or Authorized Scaming WO CSS arar dado id tii 13 VGA 1 x HD 15 Female Recycle Facility y O 7 en en eee ee ee en ee 13 DVI 1 x DVI I 29 Pin Female
4. 0 oe mb 00 w gt dl er 80 No Marker Aspect Ratio Aspect Ratio Aspect Ratio Aspect Ratio Aspect Ratio Safe Area Safe Area Safe Area Safe Area Safe Area 16 9 Marker Examples OFF No Marker 2 35 1 Aspect Ratio E 90 Safe Area 4 3 Aspect Ratio Marker
5. AL UNDER DELAY OFF H V V H SMPTE BAR OFF ON DELAY RATIO BACK FUNCTION 1 CENTER MARKER MONO CTEMP PTP DELAY RATIO BACK FUNCTION 2 CENTER MARKER MONO SYSTEM CONFIG CTEMP PTP STATUS DISPLAY OFF ON USR1 USR2 USR3 USR4 USR5 USR6 MFG USR1 USR2 USR3 USR4 SAVE CONFIG USR5 USR6 LOAD CONFIG MAIN MENU AND NAVIGATION Access the main menu by pushing and holding the MENU button on the front panel of the monitor until the main menu appears approximately 1 2 seconds Step through menu items using the and buttons Choose a menu item by pressing SELECT Rotate through options using the and buttons Choose a setting by pressing SELECT Return to the previous menu by pressing MENU Exit the main menu by pressing MENU The menu will automatically EMMENU 4UP DONN EISELECT time out after 5 seconds After exiting the menu wait 1 2 seconds before displaying the menu again MAIN MARKER SETUP VIDEO CONFIG SYSTEM CONFIG Main Menu MARKER SETUP SUBMENU 16 9 Markers MARKER SETUP MARKER 16 9 MARKER 4 3 MARKER BACKGROUND CENTER MARKER On Screen Menu continued OFF OFF OFF OFF EMMENU 4 UP DOWN EISELECT Marker Setup Submenu Use this setting to superimpose one of 10 markers on the screen when in 16 9 mode This setting is disabled when the aspect ratio is set to 4 3 or when Pixel to Pixel Underscan or H V Delay is enabled OF 13 9 ee oe oe eo 06
6. ARKER Enable and rotate amongst marker settings choices depend on aspect ratio setting MONO Enable disable monochrome mode CTEMP Rotate amongst color temperature settings PTP Enable disable Pixel to Pixel mode FUNCTION 1 is set to RATIO by default FUNCTION 2 is set to PTP by default m Status Display Use to enable on screen display of input format status in the upper left corner of the screen Saving and Loading User Configuration Presets Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets or load a preset All monitor settings on the monitor are saved including the image adjustment knob settings e Use the LOAD CONFIG menu to load one of presets USR1 USR6 Factory default settings can also be loaded by selecting MFG Factory defaults cannot be overwritten e Use the SAVE CONFIG menu to save the current settings to a preset from USR1 USRE 14 Product Overview The V LCD15SB AFHD DT is a 15 SD HD video LCD with Marshall Electronics proprietary SunBrite LCD panel designed specifically for outdoor applications or high levels of ambient light The V LCD15SB AFHD DT features our completely digital TF T MegaPixel active matrix LCD system Weighing only 8 1 lbs and only 1 77 deep this monitor is an ideal lightweight replacement for CRTs used in all broadcast and professional video applications Emulation of SMPTE C EBU color and adjustable color temperature enable the mo
7. SYSTEM CONFIGURATION SUBMENU assi A A dette adv ec E A A a NA 14 Internal SMPTE Color Bats nenes 14 Video Output Active Loop Through User Definable Function Buttons c cccecceccscesseccecessereecesvecceceevecsessaveesausarsevausarsesaavacesauvarseceuvacsareeversateevereates 14 Video PB F emale 73 0 Status DIS Pla tec a bid 14 Seo TEO MINDA l YPBPR 3 x BNC Female 75 Q Saving and Loading User Configuration Presets oooccccccconnccnnnccononenononnnnncnnnononnncnnnnonnnnrnnonnnnnnrnnononannrnnnnnnanoos 14 SDI 1 x BNC Female 75 Q Specifications a E a a a E E r E E a a E eee a E NT 15 Power Input 2 Pin Conxall Twist Lock Female Manten aC tin noia a a a a N EES 16 Tally Interface Wanani yea A wtsctue baneatan eddotse Macnee teats 16 HD 15 Female On Screen Menu continued SYSTEM CONFIGURATION SUBMENU SYSTEM CONFIG SMPTE BAR FUNCTION 1 FUNCTION 2 STATUS DISPLAY LOAD CONFIG SAVE CONFIG EMMENU 4UP DOWN E SELECT Video Configuration Submenu Internal SMPTE Color Bars Use to display internally generated SMPTE split field color bars User Definable Function Buttons Use the FUNCTION 1 and FUNCTION 2 menu items to define each function button on the front panel of the monitor The following options are available for each button DELAY Enable and rotate amongst delay modes RATIO Toggle between 4 3 and 16 9 aspect ratios BACK Rotate amongst marker backgrounds CENTER Enable disable center marker M
8. Specifications continued k 2 101 1 609 7 290 oo 5 i i AAA MASSA SARA kk hh hhddddddddddbdddddddddddddda O 2 ia z h e 0 oyo 1 006 0 O O O 20 O P on gt z c O i 0 PAARL RARA RA AA AAA A ARRE RAR AAA AA AAA A AE EN U FaR L KOSTT 4 931 Maintenance m Screen Cleaning Periodically clean the screen surface using ammonia free cleaning wipes Marshall Part No V HWP K A clean micro fiber cloth can also be used using only non abrasive and ammonia free cleaning agents Do not use paper towels Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the surface Antistatic and fingerprint resistant cleaning agents are recommended Do not apply excessive pressure to the screen to avoid damaging the LCD Faceplate Dusting Dust the unit with a soft damp cloth or chamois Dry or abrasive cloths may cause electrostatic charge on the surface attracting dust particles Neutralize static electricity effects by using the recommended cleaning and polishing practice Warranty Marshall Electronics warranties to the first consumer that this V LCD15SB AFHD DT LCD monitor will under normal use be free from defects in workmanship and materials when received in its original container for a period of one year fr
9. e back of the monitor Please note that 12 17VDC can be also supplied directly to the monitor from a variety of sources The monitor will draw approximately 3 Amps at 12 Volts in operation Connect the required cables for video signal input and output Power must be applied to the V LCD15SB AFHD DT for the active loop though outputs to be activated All BNC connectors are rated at 750 Turn on the unit by pressing the power button located on the front panel Select a video input by pressing the corresponding input select button Use to switch between 4 3 and 16 9 aspect ratios As the V LCD15SB AFHD DT monitor has a native resolution of 1024 x 768 RGB pixels incoming images are automatically scaled to fit the screen In 4 3 mode images are scaled up or down to fill the entire 4 3 screen 1024 x 768 In 16 9 mode images are scaled to fill the maximum 16 9 portion of the screen 1024 x 576 with black bars filling the remainder of the screen 4 3 Mode 16 9 Mode Note The aspect ratio setting is ignored when Pixel to Pixel mode is enabled Scanning Modes Use this setting to switch between normal and underscan modes e In normal scan mode the active portion of the video signal is displayed on the screen with 0 overscan In underscan mode area around the active video area is displayed on the screen resulting in blanking intervals being shown around the perimeter of the active image Use this mode to clearly view the ed
10. enabled sarsa Ir o y e OFF No Marker 95 Safe Area aww MES MO EC CO d Apra sersa Cp o ras 9 59 E 88 Safe Area a e IESO ee ee CS e 80 Safe Area w ESOO SOS IE CO FE a aie A 1001 59 94 A LALALA 1080i 60 1080i 59 95 1080i 50 1080psF 24 Marker Background 1080p 29 97 Use this setting to choose how selected markers are displayed on the screen 1080p 25 e OFF The marker is superimposed on the complete image 720p 60 e Half tone Image area beyond the marker is shown at 50 intensity ESO e Black Image area beyond the marker is shown at 0 intensity black Pines i 720p 50 Example 80 Marker in 4 3 Mode 720p 30 720p 29 97 720p 25 640 x 480 60Hz 640 x 480 75Hz Background OFF Half tone Background Black Background 040480 gN 800 x 600 60Hz Center Marker 800 x 600 75Hz 800 x 600 85Hz Use this setting to display a center marker on the screen This feature is not available when H V delay is on 1024 x 768 60Hz 1024 x 768 75Hz 1024 x 768 85Hz 1280 x 1024 60Hz Center Marker 10 On Screen Menu STRUCTURE OVERVIEW OFF 13 9 14 9 4 3 2 35 1 MARKER 16 9 1 85 1 95 93 90 88 80 MARKER SETUP MARKER 4 3 ed 95 93 90 88 RED 0 100 BLUE 0 100 RED 0 100 GREEN 0 100 BLUE 0 100 NAIN BLUE ONLY OFF ON PIXEL TO PIXEL OFF ON ASPECT RATIO 4 3 16 9 ADJ COLOR BIAS ADJ COLOR GAIN VIDEO CONFIG SCAN NORM
11. ges of the active video area Delay Modes Use this setting to enable one of three delay modes H V H V e In H V delay mode both horizontal sync and vertical sync are delayed resulting in both horizontal and vertical blanking periods being shown on the screen In V delay mode vertical sync is delayed so that the vertical blanking period is displayed on screen In H delay mode horizontal sync is delayed so that the horizontal blanking period is displayed on the screen Note Delay modes are only available in normal scan mode 13 On Screen Menu continued VIDEO CONFIGURATION SUBMENU continued Monochrome Mode Use this setting to enable monochrome mode Only the luminance of the image will be displayed as a grayscale picture Blue Only Mode Use this setting to enable Blue Only mode This mode displays only the blue color component of the image switching off the red and green components Use this mode when calibrating the monitor to SMPTE color bars with the following procedure 1 Allow the monitor to warm up for at least 5 10 minutes 2 Display SMPTE split field color bars on the monitor using the internal generator or an external source 3 Enable Monochrome mode 4 Locate the pluge pattern Super black black and gray bars at the lower right corner of the screen Adjust the Brightness knob until there is no visible difference between the super black and black bars but the gray bar is still visible
12. modate a variety of custom mounting options VIDEO CONFIGURATION SUBMENU VIDEO CONFIG COLOR TEMP ADJ COLOR BIAS ADJ COLOR GAIN MONO BLUE ONLY PIXEL TO PIXEL ASPECT RATIO SCAN DELAY ETMENU UP DOWN SELECT Video Configuration Submenu Color Temperature Presets Use this setting to choose one of three color temperature presets e D55 5500K e D65 6500K e D93 9300K e USER Adjustable Color Bias and Gain m Adjusting Color Bias ADJ COLOR BIAS RED GREEN BLUE EMMENU UP DOWN ESELECT Color Bias Menu Use this submenu to adjust bias of the color response Adjust the bias for each color to alter the white balance of the image The Color Temperature preset will automatically switch to USER when Color Bias settings are adjusted It is normal for color bias adjustments to be very subile m Adjusting Color Gain ADJ COLOR GAIN RED GREEN BLUE EMMENU UP DOWN EISELECT Color Gain Menu Use this submenu to adjust gain of the color response The Color Temperature preset will automatically switch to USER when Color Gain settings are adjusted On Screen Menu continued On Screen Menu continued Compatible Input Formats MARKER SETUP SUBMENU continued EA Format e 1 LAA ee Use this setting to superimpose one of 5 markers on the screen when in 4 3 mode This setting is disabled when the E ff aspect ratio is set to 16 9 or when Pixel to Pixel Underscan or H V Delay is
13. n Size 15 0 Diagonal 3 LEDs Green Red Yellow Activation requires contact FANS EAT E O 3 Display Area h xv 304 128 x 228 096 mm closure of pin to ground on the HD 15 connector Aspect Ratio 4 3 Native 4 3 16 9 Modes Installation and Initial Seti 4 o h pea ies Pine f Signal ____ ET I Ee A terpenes N atenaaee 4 Dolce ee ne 2 Red Viewing Angle h xv 160 x 140 3 Yellow lalo A east en As EE eens i eer en ls Sone acne E Wa E O heel nie aba uei ease 4 Brightness 600 cd m AM eena Connections ama POW Oli 4 Contrast Ratio 600 1 age Dot Pitch h x v 0 099 x 0 297 mm FrontPanel Features acantilados 5 Pixel Pitch h x v 0 297 x 0 297 mm B8 HUNG 7 Power BUIN de 5 Pixel Response 18 ms rise fall put Select BUON S Seriean rt 5 ee NC On SGCreen Menu NavigalomBUloAS sara 5 User Detinable Funcion BUON sii aaa 5 mage Ad US TMENtIA OS dida 5 VIDEO INPUT OUTPUT Tam OS rd a aan 5 Video Input Output R p Feat 6 Supports SMPTE 170M NTSC PAL ios UTOS cisco in ii A A A a errr Cree Color burst sub carrier required ELECTRICAL LN A iakaeeemen red se 6 S Video Y C Input Output Power Consumption 3A 12VDC 36 W TAV INEN A A anda 6 Supports SMPTE 170M NTSC PAL Voltage Requirement 12 14 VDC Mounting MOS ar rada adi 6 YPsPr Input Output V PS12 5V 1 Power Supply Compatible Input FOrMalS iaa a a is 7 Supports SMPTE 260M 274M 296M Input 100V 240V 50 60Hz Output 12 14V 5A HD SDI Input Output osha Teo eee en ea aT R TEE TY
14. o user definable function buttons on the front panel allow quick access to numerous settings and features including aspect ratio screen markers monochrome mode color temperature delay mode and more On Screen Menu continued Installation and Initial Setup VIDEO CONFIGURATION SUBMENU continued Unpackin p g Aspect Ratio Settings Carefully unpack the V LCD15SB AFHD DT monitor and verify that the following items are included e V LCD15SB AFHD DT Monitor with Attached Desktop Stand e V PS12 5V 1 Power Supply with Conxall 2 Pin Twist Lock Connector e Operating Instructions Inspect the unit for any physical damage that may have occurred during shipping Should there be any damage immediately contact Marshall Electronics at 800 800 6608 If you are not located within the continental United States call 1 310 333 0606 Installation The V LCD15SB AFHD DT monitor is shipped with pre installed desktop stand allowing the monitor to be flexibly used in the field The monitor can also be installed in an EIA standard 19 inch rack occupying 6RU contact Marshall Electronics When installed in a rack the unit can be rotated 360 to achieve the desired viewing angle A VESA standard 75mm hole pattern also allows custom mounting installations on stands or articulating arms Connections and Power On Plug the V PS12 5V 1 power supply into an AC power source 100 240 V 50 60 Hz Attach the 2 pin twist lock connector to th
15. odates virtually all video formats Input types include Composite Video S Video YPbPr SDI VGA and DVI with HDCP Accepted formats include NTSC PAL 480i p 576i p 720p 10351 and 1080i p standards as well as VESA PC formats through SXGA 1280 x 1024 End to End Digital Signal Processing Analog signals are digitized using an advanced 10 bit process with 4x over sampling 5 line super adaptive 2D comb filtering and exacting color space conversion Video is scaled to fit on the screen in the highest possible resolution using a state of the art LSI that incorporates precision gamma correction and our HyperProcess motion adaptive interpolation for interlaced images m ColorMatch Conversion with Color Temperature Adjustment Emulation of SMPTE C EBU color space allows the V LCD15SB AFHD DT to replace any broadcast CRT monitor Settings include D55 D65 and D95 Bias and Gain adjustment for each color enables precise color matching and white balance Advanced Features Aspect ratio settings underscan mode blue only mode monochrome mode and H V delay are a few of the advanced features making the V LCD15SB AFHD DT at home in any broadcast environment Pixel to Pixel mode also allows native display of any incoming image format Flexible Screen Markers A variety of screen markers in both 4 3 and 16 9 modes allow accurate monitoring of the different aspect ratios used in broadcast environments User Definable Function Buttons Tw
16. om the purchase date This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty lf there is no proof of purchase provided with a warranty claim Marshall Electronics reserves the right not to honor the warranty set forth above Therefore labor and parts may be charged to the consumer This warranty does not apply to the product exterior or cosmetics Misuse abnormal handling alterations or modifications in design or construction void this warranty It is considered normal for a minimal amount of pixels not to exceed three to fail on the periphery of the display active viewing area Marshall Electronics reserves the option to refuse service for display pixel failure if deemed unobtrusive to effective use of the monitor by our technicians No sales personnel of the seller or any other person is authorized to make any warranties other than those described above or to extend the duration of any warranties on behalf of Marshall Electronics beyond the time period described above Due to constant effort to improve products and product features specifications may change without notice Updated 05 18 07 Marshall Electronics Inc 1910 East Maple Ave El Segundo CA 90245 Tel 800 800 6608 310 333 0606 Fax 310 333 0688 www LCDRacks com sales Icdracks com 16 V LCD15SB AFHD DT Operating Instructions Contents Specifications PANEL TALLY Produc OVER NA a 3 Scree
17. st precise color representation possible Our proprietary digital signal processing features 10 bit A D conversion of all analog signals with 4X over sampling and 5 line super adaptive 2D comb filtering of composite signals De interlacing is performed using our HyperProcess algorithm with motion adaptive interpolation The V LCD15SB AFHD DT features multi format compatibility accommodating virtually all video formats including NTSC PAL 480i p 720p and 1080i p formats VGA and DVI inputs accept VESA standards allowing the display to be used as a computer monitor Advanced features include aspect ratio settings a variety of screen markers underscan mode blue only mode monochrome mode H V delay and Pixel to Pixel mode Features m High Resolution 15 SunBrite Panel The V LCD15SB AFHD DT features Marshall Electronics new SunBrite LCD panel dramatically boosting the efficiency of the backlight s light utilization and minimizing the surface reflection of ambient light The transmissive LCD produces high contrast images even in challenging outdoor lighting conditions This technology features a much wider color reproduction range than typical transflective reflective LCDs with increased backlight performance The LCD panel features a brightness of 600 cd m 600 1 contrast ratio and 160 horizontal and 140 vertical viewing angles Multi Format Compatibility With a variety of analog and digital inputs the V LCD15SB AFHD DT accomm
18. t Panel Features 1 Power Button Turn the monitor on by pressing the power button In the OFF state the LED will shine brightly The LED will dim when the monitor is turned on Input Select Buttons Use the input select buttons to select the input to be displayed e Video e S Video e YPbPr SD HD e VGA e DVI e SDI Each input automatically detects the applicable formats See Compatible Input Formats Page 7 On Screen Menu Navigation Buttons Use the Menu 7 and Select buttons to display and navigate the on screen menu See Main Menu and Navigation Page 8 User Definable Function Buttons Two user definable function buttons can be used for direct access to various settings Functions are assigned using the on screen menu See User Definable Function Buttons Page 14 Image Adjustment Knobs Use the image adjustment knobs to adjust the following settings Pressing each knob will display the current status of the corresponding control e Brightness 0 64 e Color 0 64 e Tint 0 64 NTSC Only e Contrast 0 64 Q Tally Lights Three tally LEDs green red and yellow are provided as general purpose indicators Each LED can be individually controlled providing multiple indications Tally LEDs are controlled via the HD 15 connector on the rear panel See Tally Interface Page 6 Mee ew ew ee ewww ew r lt o CONTRAST OOOO
Download Pdf Manuals
Related Search