Home
Marantz SR7300OSE User's Manual
Contents
1. 24 4 SURROUND 24 5 PL II PRO LOGIC Il MUSIC 25 6 CS Il CIRCLE SURROUND Il PARAMETER 25 7 MULTI ROOM 25 87 1 CH INPUT LEVEL 26 9 DC TRIGGER SETUP e 26 BASIC OPERATION PLAY BACK 27 SELECTING AN INPUT SOURCE 27 SELECTING THE SURROUND MODE rere 27 ADJUSTING THE MAIN VOLUME 27 ADJUSTING THE TONE BASS amp TREBLE CONTROL 27 TEMPORARILY TURNING OFF THE SOUND 28 USING THE SLEEP TIMER 28 Vies B Tt 28 SURROUND MODE 29 OTHER FUNCTION 32 TV AUTO ON OFF 2 12 32 ATTENUATION TO ANALOG INPUT SIGNAL 32 LISTENING OVER HEADPHONES e 32 VIDEO ON OFF eg 32 DISPLAY MODE 32 SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT 32 RECORDING AN ANALOG SOURCE 33 BEE 33 SPEAKER AR 33 7 1 CH INL 34 EE 34 BASIC OPERATION TUNER 35 LISTENING TO THE TUNER 35 PRESET MEMORY 35 MULTI ROOM SYSTEM 38 MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS 38 OPERATION TO MULTI ROOM OUTPUTS WITH THE REMOTE CONTROLLER FROM SECOND ROOM
2. To temporarily silence all speaker outputs such as when interrupted by a phone call press the MUTE button on the front panel or MUTE button on the remote This will interrupt the output to all speakers and the head phone jack but it will not affect any recording or dubbing that may be in progress When the system is muted the display will show MUTE Press the MUTE button again to return to normal operation USING THE SLEEP TIMER POWER ON OFF V OFF 7 1 6 1 IP AUDIO ANGLE SUBTITLE AUTO DTS DISP RDS CHST F DIR SEAR STEREO VIRTUAL DSP PTY oS Ce S DIRECT SURR MODE NIGHT MEMO To program the SR7300 for automatic standby press SLEEP button on the remote Each press of the button will increase the time before shut down in the following sequence OFF gt 10 20 30 40 90 d80 70 80 50 The sleep time will be shown for a few seconds in the display on the front panel and it will count down until the time has elapsed When the programmed sleep time has elapsed the unit will automatically turn off Note that the SLEEP indicator on the display will light up when the Sleep function is programmed To cancel the Sleep function press the SLEEP button until the display shows to SLEEP OFF and the SLEEP indicator disappear NIGHT MODE ClO 1S STEREO VIRTUAL _ DSP PTY
3. LEARNING REMOTE CONTROLLER RC7300SR POWER ONOFF Tuns te VOR 7 o 0 9 mushemmek oe Record o Sm gt Pay V OFF EQ 6 SLEEP AUDIO ANGLE SUBTITLE A D 7 SC DISP RDS 57 8C F DIR SEAR d 10 NIGHT MEMO INPUT T MODE P SCAN MUTE DECK A SETUP EXIT CHANNEL 5 TUNE SEARCH REC SPKR ATT MULTI ooon LEARNING REMOTE CONTROLLER RC7300SR ANGLE SUBTITLE A D D I 3 DIS DISP RDS CHST F DIR SEAR SETUP EXIT CHANNEL 5 SEARCH SPKR MULTI CONTROLLING MARANTZ CD PLAYER CD MODE POWER ONOFF Turns te OD payer on and oi a 7 doses the soray 0 9 mushemmek Jas Sm gt Pay CONTROLLING A MARANTZ CD RECORDER CDR MODE POWER ONOFF Tums OD recorderon anda a Opens closes he dso ray 0 9 _ ngusthe numero e Red o e m bo p Pg I o 2 TT JOEPIE EQ 7 1 6 1 IN SLEEP AUDIO ANGLE SUBTITLE A D TS DISP RDS CHST F DIR SEAR SETUP EXIT Cae CHANNEL 5 TUNE SEARCH REC SPKR ATT MULTI EQ 7 1 6 1 IN SLEEP AUDIO ANGLE SUBTITLE A D AUTO oo DIS DISP RDS 5 csit M CHST F DIR SEAR
4. DSP TY MEMO INPUT T MODE P SCAN MUTE c AT DEKE 4 Onn MENU O MENU 1050 SETUP EXIT Orc e 0 CHANNEL 5 TUNE SEARCH REC SPKR A B ATT MULTI CONTROLLING MARANTZ MD DECK MD MODE POWER ONOF Tus he MD oi 0 9 Inputs the numeric CL Clears the inputting CL MEMO Programs Skips forward or previous track m pae m gp ooo Play POWER ONOFF Turns he ape deck on ando a famen oo 4 hangesthe e po 000 Pase o Sm gt y _ LEARN MODE The remote controller is capable of learning and memorizing the remote control codes used by almost any other remote controller you may already own e If no commands have been programmed for a particular function button the remote controller will transmit whatever codes have been factory preset he following example shows how to program your remote controller and how to use the codes for a DVD player LEARNING PROCEDURE 1 Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 5 centimeters 2 Press and hold down the T MODE and MEMO buttons until LEARN is displayed in the display 0 M ec CH OC E aa s Sa l GO MC 00 SECH MENU N 3 Select the Function button to select the function
5. 38 REMOTE CONTROLLER OPERATION 39 CONTROLLING MARANTZ COMPONENTS 39 LEARN MODE enc 41 MACRO 42 TROUBLESHOOTING 46 TECHNICAL SPECIFICATIONS 48 DIMENSION ee 48 I o 2 TT m Z G ay I INTRODUCTION Thank you for purchasing the Marantz SR7300 Surround receiver This remarkable component has been engineered to provide you with many years of home theater enjoyment Please take a few minutes to read this manual thoroughly before you connect and operate the SR7300 As there are a number of connection and configuration options you are encouraged to discuss your own particular home theater setup with your Marantz A V specialist dealer PRECAUTIONS CAUTIONS ON INSTALLATION For heat dispersal leave at least 20 cm 8 inch of space between the top back and sides of this unit and the wall or other components Do not obstruct the ventilation holes 2 20 8 6 6 20 cm 8 ins Iz 2 DESCRIPTION DIGITAL SURROUND DTS was introduced in 1994 to provide 5 1 channels of discrete digital audio into home theater systems DTS brings you premium quality discrete multi channel digital sound to both movies and music DTS is a multi channel sound system designed to create full ran
6. INPUT T MODE P SCAN MUTE A V OFF EQ 7 1 6 1 IN SLEEP AUDIO ANGLE SUBTITLE A D 07 N 0 INPUT T MODE P SCAN MUTE oy You can select the display mode for the front display of the SR7300 To select this mode press the DISP on the remote control unit When this button is pressed the display mode is switched in the following sequence Surround Mode Auto display Off Display Off Input Function gt Surround Mode In Auto display off mode turn the display on automatically after that any condition of SR7300 is changed In Display off mode turn the display off completely Notes e Only DISP indicator will light up on the front display in display off condition SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT POWER POWER oy V OFF EQ 7 1 6 1 IN SLEEP e AUDIO ANGLE SUBTIT A D 00 DTS NISP RDS EX ES SI M CHST FDIR SEAR INPUT T MODE P SCAN MUTE If you have already assign any digital input to input source You can select temporarily the audio input mode for each input source with the A D button on the remote controller or front panel When this button is pressed the input mode is switched in the following sequence Digital Auto Digital Analog Digital Auto In Digital Auto mode the types of signals being input to the digital and an
7. 4 When you are finished programming macros press and hold the EDITING MACROS OK button until the display returns to USE mode Macros may be edited using following procedure 22 1 Press and hold the T MODE and MENU button until the MACRO gt is displayed on the LCD e LEARN and MACRO is displayed blinking I o 9 2 TT e Macros cannot be programmed for the MEMO cursor OK VOL A V or CL buttons In the macro mode it is possible to program the memory to perform macros containing up to 10 steps Each of the function operations 12 including CD CD R etc 2 Pressthe Function button to be changed can be used in a macro more than once however for all except AMP only the first function operation will be ae OLNE DVO Payer py pressing Me transmitted as a signal from the remote controller Ee Accordingly within a single macro it is not possible to switch DVD M LEARN and MACRO is displayed blinking between multiple function operations This is to prevent the poo Go bg S by switching of the receiver function operation Within a macro ec o the second time a function operation is used it will only be lool ay used on the remote controller itself no signal will be transmitted to the component Note 3 Press the Cursor V button to select
8. S DIRECT SURR MOD DECKA DECK B Press the NIGHT button on the remote to tur n on the NIGHT mode Selecting the Night Mode ON is effective in Dolby Digital only and it compresses the dynamic range This softens loud passages such as sudden explosions to help prevent disturbing others late at night To turn off the Night mode press the NIGHT button again 28 SURROUND MODE The SR7300 is equipped with many surround modes These are provided to reproduce a variety of surround sound effects according to the content of the source to be played The available surround modes may be restricted depending on the input signal and speaker setup AUTO When this mode is selected the receiver determines whether the digital input signal is Dolby Digital Dolby Digital Surround EX DTS DTS ES DTS 96 24 or PCM audio Surround EX amp DTS ES will operate for multi channel source that has a Dolby Digital Surround EX or DTS ES auto trigger flag in the digital signal When a Dolby Digital or DTS signal is input the number of channels for which the corresponding signal is encoded will be played Inputting a Dolby Digital two channel signal with Dolby surround status automatically subjects that signal to Pro Logic movie processing before play PCM 96 kHz source material can be played in this mode HDCD source material can be played in this mode OSE version only Notes When you use this mode with certain DVD an
9. ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 Pus POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la Classe B est conforme la norme NMB 003 du Canada TABLE OF CONTENTS INTRODUCTION E 2 PRECAUTIONS 2 DESCRIP 2 FEATURES Ee 4 ACCESSORIES sosisini 4 5 FLDIOPLAY E 7 REAR PANEL E 8 REMOTE CONTROLLER RC7300SR 10 NAMES AND FUNCTIONS 10 REMOTE CONTROL RANGE 12 LOADING BATTERIES 12 GENERAL INFORMATION OF RC7300SR SR7300 13 CONNECTIONS eere eene enn 14 SPEAKER PLACEMENT 14 CONNECTING 15 CONNECTING AUDIO COMPONENTS 16 CONNECTING VIDEO COMPONENTS 17 ADVANCED CONNECTING 18 CONNECTING REMOTE CONTROL JACKS 18 CONNECTING THE ANTENNA TERMINALS 19 CONNECTING FOR THE MULTI 2 20 SE TUP A 21 ON SCREEN DISPLAY MENU STE 21 1 INPUT SETUP ASSIGNABLE DIGITAL 22 2 SPEAKER SETUP tte 22 3
10. more than 1 second on the remote Automatic searching begins then stops when a station is tuned in If tuning does not stop at the desired station use to the Manual tuning operation MANUAL TUNING 2 1 CHANNEL SKIP TUNE SEARCH ees USING THE SR7300 select tuner and desired band FM or AM press the TUNER button on the front panel 2 Press the F P Frequency Preset button on front panel to appears frequency on the display Press the TUNING lt or gt button Using the remote control unit 1 To select tuner and desired band FM or AM press TUNER button twice within in two seconds on the remote Press lt 4 or on the remote to tune in the desired station DIRECT FREQUENCY CALL SE um SETUP EXIT E CHSEL T CHANNEL 5 TUNE SEARCH EM gt gt REC SPKRA B MULTI OH H m a 1 To select tuner and desired band FM or AM press TUNER button twice within in two seconds on the remote 2 Press the F DIR on the remote display will show FREQ J Input your desired station s frequency with ten keypad on the remote 4 The desired station will automatically be tuned FM TUNING MODE AUTO STEREO OR MONO DEL When in the auto stereo mode AUTO indicator keeps to light on t
11. 418 mm 20 mm 13 16 ins 17 5 16 ins 440 mm 5 3 4 ins 146 mm 6 3 8 ins 162 3 mm COUNTRY COMPANY ADDRESS ALGERIE Azur 2000 8 Lotissement Ben Hatadi Alger Algerie ARMENIA NGYIG Ltd 47 A 75 St Lalaiants 375000 Yerevan Armenia AUSTRALIA QualiFi Pty Ltd P O Box 350 Mt Waverley VIC 3149 Australia AUSTRIA Huber amp Prohaska GmbH TaborstraBe 95 LadestraBe 1 Geb ude Hangartner A 1200 Wien Austria BAHREIN Ambassador Stores P O Box 237 141 Government Avenue Manama Bahrein BANGLADESH Target 1078 Ramjoy Mohanja Lane Asadgonj Chittagong 4000 Bangladesh BELGIUM Van der Heyden Audio N V Brusselbaan 278 9320 Erembodegem Belgium BULGARIA Ariescommerce GmbH Makedonia Blvd 16 1606 Sofia Bulgaria CANADA Lenbrook Industries Limited 633 Granite Court Pickering Ontario CHINA Guang Chang Audio International Co Ltd No 38 Yushan Road ShiQiao Pan Yu Guang Dong China CYPRUS Empire Hifi systems Ltd P O Box 5604 Nicosia Cyprus CZECH REPUBLIC Audio International Sokolska 41 67902 Rajecko OKR Blansko Czech Republic DENMARK Audio Nord Dali All 1 9610 Noerager Denmark DUBAI V V amp SONS P O Box 105 Dubai U A E EGYPT Solimco 9 El Attibaa St Doki Cairo Egypt ESTONIA HiFi Club Estonia Ehte 4 90503 Haapsalu Estonia F Y R O M T P KODI ul Cedomir Kantargiev 21a Skopje Former Yugoslavian Republic of Macedonija FINLAND Audio
12. Dolby D Dolby Surr EX DIGITAL OO SURROUND DIGITAL Dolby D 5 1ch DIGITAL Dolby D 2ch DIGITAL Dolby D 2ch Surr DODIGITAL nd SURROUND DTS ES dts ES DTS 96 24 dts 96 24 DTS 5 1ch dts PCM Audio PCM PCM 96kHz PCM HDCD PCM HDCD STEREO Analog Dolby Surr EX ANALOG DIGITAL Dolby D 5 1ch DIGITAL Dolby D 2ch DIGITAL Dolby D 2ch Surr DIGITAL OO SURROUND DTS ES dts ES DTS 5 1ch dts PCM Audio PCM Analog Dolby Surr EX Dolby Digital EX ANALOG DIGITAL Dolby D 5 1ch Dolby Digital 5 1 DIGITAL Dolby D 2ch Multi Channel Stereo DIGITAL Dolby D 2ch Surr Multi Channel Stereo DIGITAL OO SURROUND DIS ES DIS ES dts ES DTS 5 1ch DTS 5 1 dts PCM Audio Multi Channel Stereo PCM Analog Multi Channel Stereo Note e Dolby Digital 2 ch Lt Rt signal with Dolby Surround flag Speakers are full set No sound outputs from the surround speaker center speaker and subwoofer if the DVD disc has no surround data HDCD OSE version only ANALOG Fr
13. ERRA A E cA En UZ Model SR7300 SR73000SE User Guide AV Surround Receiver RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the AN N WARNING literature accompanying the product TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR VITER LES CHOC LECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV Cable TV system installers attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as
14. Function button DVD M LEARN and MACRO is displayed blinking Ou E cro ola lo USING MACROS E Metz ex ef TE DAR The following procedure will show how to use the function buttons for which you have programmed macros 3 Press the VOL A button 1 Press the Function button for the desired macro for 3 seconds DVD 1 is displayed and LEARN is disappeared MACRO is displayed on LCD for approximately 1 second The programmed operation is transmitting ie which the number of steps in the macro is displayed on Ask Sp MACRO AWN TZ IN H 4 Repeat step 3 until the last number of the macro is displayed The display will return to step 1 e The each programmed operation is transmitting when the number of the macro is displayed 5 To return the USE mode press and hold down the OK button until USE is displayed in the display e The remote controller will do nothing if no macros are programmed The macro steps are executed in order and the names of their buttons are displayed on the LCD Also the step numbers displayed on LCD disappear as each step is executed 2 After all macro commands have been transmitted the remote controller returns to AMP in use mode 43 m Z G 70 I EXAMPLES OF MACRO PROGRAMS Example 1 Change the input source for the amplifier to CD and play the 3rd trac
15. SR7300OSE Front KEE 8 ohms 110 W Ch Center 8 ohms 110 W Ch Surround 8 ohms 110 W Ch Surround BaCk AN RT E 8 ohms 110 W Ch TECHNICAL SPECIFICATIONS FM TUNER SECTION LAR 6 ohms 135 W Ch EE 6 ohms 135 W Ch S rro nd L amp R 6 ohms 135 W Ch Surround Back iioii tdt 6 ohms 135 W Ch Input Sensitivity Impedance 168mV 47 Kohms Signal to Noise Ratio Analog Input Source Direct 105 dB Frequency Response Analog Input Source Direct 8 Hz 100 kHz 3 dB Digital Input 96 kHz PCM 8 Hz 45 kHz dB VIDEO _ Television Format NTSC Input Level Impedance 1 Vp p 75 ohms Output Level Impedance 1 Vp p 75 ohms Video Frequency Response 5 Hz to 8 MHz 1 dB 60 dB GENERAL Power Heourement nn AC 120 V 60 Hz Power Consumption 480 W Weight 7300 555 555 28 9 Ibs 13 1 Kg 5 7 32 4 Ibs 14 7 Kg ACCESSORIES Remote Control Unit RO7300SR 1 2 FM ANEMA mtcr 1 Loop ME E EE 1 Specifications subject to change without prior notice DIMENSION 48 25mm 1 in 18 1 4 ins 463 mm 16 7 16 ins
16. 10 ft SURR BACK 10 ft 3333535353 MAIN RETURN NEXT EXIT 1 To select the each speaker press A or V cursor button 2 To set the distance for each speaker press the lt or gt cursor buttons 3 i you finish these setup move cursor to NEXT with A or V cursor button and then press OK button to go to next page FRONT L Set the distance from the front left speaker to your normal listening position between 1 and 30 feet in 1 0 foot interval 0 3 to 9 meters in 0 3 meter intervals FRONT R Set the distance from the front right speaker to your normal listening position between 1 and 30 feet in 1 0 foot interval 0 3 to 9 meters in 0 3 meter intervals CENTER Set the distance from the center speaker to your normal listening position between 1 and 30 feet in 1 0 foot interval 0 3 to 9 meters in 0 3 meter intervals SURR L Set the distance from the surround left speaker to your normal listening position between 1 and 30 feet in 1 0 foot interval 0 3 to 9 meters in 0 3 meter intervals SURR R Set the distance from the surround right speaker to your normal listening position between 1 and 30 feet in 1 0 foot interval 0 3 to 9 meters in 0 3 meter intervals SUB W Set the distance from the subwoofer to your normal listening position between 1 and 30 feet in 1 0 foot intervals 0 3 to 9 meters in 0 3 meter intervals SURR BACK Set the distance from a surround back speaker to your normal listening positi
17. Can not select EX ES mode Surround center NONE has been selected in SPEAKERS Make the correct setting SIZE SETUP Use 5 1channel source Input signal is incompatible Can not select Pro Logic II mode Input signal is incompatible Use 2 channel Dolby Digital input signal PCM input signal or analog input signal Can not select Neo 6 mode Input signal is incompatible Use 2 channel Dolby Digital input signal PCM input signal or analog input signal Can not select CSII mode Input signal is incompatible Use 2 channel Dolby Digital input signal PCM input signal or analog input signal No output to Sub Woofer Out Sub woofer NONE has been selected in SETUP mode Select Sub woofer YES Noise is produced during DTS Analog has been selected for input Be sure to perform digital connection select digital input then play encoded CD or laser disc play A specific channel does not Nothing recorded on source Check the encoded channel on the source side produce output FM or AM reception fails Antenna connection is incomplete Correctly connect the indoor FM and AM antennas to FM and AM antenna outlets Noise is heard during AM reception Reception is affected by other electrical fields Try changing location where the AM indoor antenna is set up Noise is heard during FM reception The radio waves from the broadcasting station are weak Install an FM outdoor antenna Cannot get programmed station Preset data has been era
18. Riga LV 1011 Latvia LEBANON AZ Electronics S A 1 P O Box 11 2833 Beirut Lebanon LITHUANIA Accapella Ltd Ausros Vartu G 5 Pasazo SKG 2001 Vilnius Lithuania MALAYSIA Wo Kee Hong Electronics Sdn Bhd 2nd Floor Bangnan Infinite Centre Lot1 Jalan 13 6 46200 Petaling Jaya Selangor Datul Ehsan Malaysia MALTA Doneo Co Ltd 78 The Strand Sliema SLMO7 Malta MAURITIUS SKR Electronics Ltd P O Box 685 Bell Village Port Louis Mauritius MILITARY MARKET EUROPE PASCO GmbH PO BOX 1280 Sandhausen 69200 Germany NEW ZEALAND Wildash Audio Systems 14 Malvern Road Mt Albert Auckland New Zealand NORWAY Audio Nord Sandkerveien 64 Oslo 0483 Norway OMAN Mustafa amp Jawad Trading CO P O Box 1918 Ruwi Oman POLAND Philips Polska Sp 2 0 0 Al Jerozolimskie 195b 02 222 Warszawa Poland PORTUGAL Corel2 Comercio de Electronica Lda Av Luis Bivar No 85 A 1050 Lisboa Portugal PROFESSIONAL EUROPE Marantz U K Ltd Kingsbridge House Padbury Oaks 575 583 Bath Road Longford Middlesex UB7 OEH U K PROFESSIONAL U S A Marantz America Inc 1100 Maplewood Drive Itasca IL 60143 U S A QATAR Almana amp Partners W W L P O Box 49 Doha Qatar REUNION Vision 180 Rue du Marechal Leclerc 97400 Saint Denis de la Reunion ROMANIA Nova Music Entertainment 5 Zagazului Str Bl 1G apt 18 sector 1 Bucharest Romania RUSSIA Absolute Audio 7 2 M
19. increments of 3 seconds for each channel Using the Left and Right cursor buttons adjust the volume level of the noise from the speaker so that it is the same level for all speaker If you select MANUAL adjust the output level of each speaker as follow 1 When you move cursor to FRONT L by pressing V cursor button the SR7300 will emit a pink noise from the front left speaker Remember the level of this noise and then press the V cursor button Note that this can be adjusted to any level between 10 and 10 dB in 1 dB intervals except the subwoofer setting The subwoofer can be adjusted to any level between 15 and 10 dB in 1 dB intervals The SR7300 will now emit the pink noise from the center speaker 2 Using the lt and cursor buttons adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker Press the Y cursor button again The SR7300 will now emit the pink noise from the front right speaker 4 Hepeat steps 2 and 3 above for the front right and other speakers until all speakers are adjusted to the same volume level If you finish these setup press OK button the cursor will move to MAIN and then press OK button to go to SETUP MAIN MENU I o 2 TT 23 m Z G E ay I Notes e Speakers that you selected None for in the Speaker Size menu will not appear The setting of Sur Back L and Surr Back R appears if set for
20. 6 channels of surround audio and a LFE subwoofer signal The CS II decoder creates a listening environment that places the listener inside music performances and dramatically improves both hi fi audio conventional surround encoded video material CS II provides composite stereo rear channels to greatly improve separation and image positioning adding a heightened sense of realism to both audio and A V productions CS II is packed with other useful feature like dialog clarity SRS Dialog for movies and cinema like bass enrichment TruBass CS II can enable the dialog to become clearer and more discernable in movies and it enables the bass frequencies contained in the original programming to more closely achieve low frequencies overcoming the low frequency limitations of the speakers by full octave SRS Circle Surround II SRS Dialog SRS TruBass SRS and 0 symbol are trademarks of SRS Labs Inc SRS Circle Surround II SRS Dialog and SRS TruBass technology are incorporated under license from SRS Labs Inc seit HDCD High Definition Compatible Digital 9 is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed HDCD encoded CDs sound better because they are encoded with 20 bits of real musical information as compared to 16 bits for all other CDs HDCD overcomes the limitation of the 16 bit CD format by using a sophisticated system to encode the additional four bits
21. 6 technology allows various sound elements within a channel or channels to be steered separately and in a way which follows naturally from the original presentation Neo 6 offers a music mode to expand stereo nonmatrix recordings into the five or six channel layout in a way which does not diminish the subtlety and integrity of the original stereo recording EXTENDED SURROUND DTS ES Extended Surround is a new multi channel digital signal format developed by Digital Theater Systems Inc While offering high compatibility with the conventional DTS Digital Surround format DTS ES Extended Surround greatly improves the 360 degree surround impression and space expression thanks to further expanded surround signals This format has been used professionally in movie theaters since 1999 In addition to the 5 1 surround channels FL FR C SL SR and LFE DTS ES Extended Surround also offers the SB Surround Back channel for surround playback with a total of 6 1 channels DTS ES Extended Surround includes two signal formats with different surround signal recording methods as DTS ES Discrete 6 1 DTS ES Matrix 6 1 DTS DTS ES Extended Surround and Neo 6 are trademarks of Digital Theater Systems Inc The stereo CD is a 16 bit medium with sampling at 44 1 kHz Professional audio has been 20 or 24 bit for some time and there is increasing interest in higher sampling rates both for recording and for delivery into
22. Digital RF input jack Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack The digital signal jacks on this unit conform to the EIA standard If you use a cable that does not conform to this standard this unit may not function properly Each type of audio jack works independently Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks respectively CONNECTING VIDEO COMPONENTS VIDEO PROJECTOR DVD PLAYER DIGITAL AUDIO VIDEO ES S VIDEO OUT OUT OUT VIDEO OUT OUT amp Y CB PB CR PR There types of video jacks on the rear panel VIDEO jack The video signal for the VIDEO jacks is the conventional composite video signal S VIDEO jack The video signal is separated into luminance Y and color C signals for the S VIDEO jack The S VIDEO signals enables high quality color reproduction If your video component has an S VIDEO output we recommend to use it Connect the S VIDEO output jack on your video component to the S VIDEO input jack on this unit Component jack Make component video connections to a TV or monitor with component inputs to produce a higher quality video images Use component video cable or 3 video cords to connect the component video out jacks on the SR7300 to the monitor Notes Be sure to c
23. Input cable connected incorrectly Connect the cable correctly by referring to the connection diagram than equipment selected with the Cancel mute using the remote control unit See the connection diagram and connect the cables correctly function selector Sound from the wrong channel is Speaker cable connected incorrectly Connect the cable correctly by referring to the connection diagram output from the speaker No sound is output from the center The center speaker cable connection is incomplete Connect the cable correctly speaker STEREO has been selected for Surround mode When STEREO is selected for Surround mode no sound will be output from the center speaker Set another Surround mode Center NONE has been selected in SETUP mode Make the correct setting No sound is output from the The surround speaker cable connection is incomplete Connect the cable correctly surround speakers STEREO has been selected for Surround mode When STEREO has been selected for Surround mode no sound will be output from the surround speaker Set another Surround mode Surround NONE has been selected in SETUP mode Make the correct setting No sound is output from the surround back speaker cable connection is incomplete Connect the cable correctly surround back speaker Surround mode is not EX ES mode Surround back NONE has been selected in SPEAKERS Set surround mode EX ES SIZE SETUP Make the correct setting
24. Nord Uudenmaankatu 4 6 Helsinki SF 00120 Finland FRANCE Marantz France A division of Marantz Europe B V P O Box 301 92 156 Suresnes Cedex France GERMANY Marantz Deutschland Hakenbusch 3 49078 Osnabr ck Germany GREECE Adamco S A 188 Hippocratous Street 11471 Athens Greece HEADQUARTERS EUROPE Marantz Europe B V P O Box 8744 5605 LS Eindhoven The Netherlands HONG KONG Marantz Hong Kong Ltd Unit 1706 Metroplaza 11 223 Hing Fong Road Kwai Fong N T Kowloon Hong Kong HUNGARY Infovox Ltd Terez Krt 31 1067 Budapest Hungary ICELAND ID Electronics Ltd Armula 38 108 Reykjavik Iceland INDIA NOVA Audio Private 8 Punam Co op Society 29 30 Road 5 Union Park MUMBAI 400052 India IRAN Home Co 5th floor no 878 Philips Building Enghelab ave P O 11365 7844 Tehran Iran IRELAND Marantz Ireland Clonskeagh Dublin 14 Ireland ISRAEL Elmor Ltd 52 Heh Beiyar Street Kikar Hamedina Tel Aviv Israel ITALY Marantz Italy Via Casati 23 20052 Monza Milano Italy Servizio Consumatori 1678 20026 Numero Verde IVORY COAST Hifivoir B P 2428 Abidjan 01 Ivory Coast JAPAN Marantz Japan Inc 35 1 Sagami Ohno 7 Chome Sagamihara shi Kanagawa 228 8505 Japan KOREA MK Enterprises Ltd Rm604 Electro officetel 16 58 Hangang ro 3Ga Yongsan Ku Seoul Korea KUWAIT alAlamiah Electronics Intl P O Box 8196 Salmiah 22052 Kuwait LATVIA Ace Ltd 61 LacPlesa Str
25. SSS oo MONITOR d HEN WW eee 20 SETUP 7 Select the AMP mode in remote control unit 2 Press SETUP button on the remote control unit to display the SETUP MAIN MENU of the OSD menu system There 9 After all components are connected initial setup must be performed items in the SETUP MAIN MENU ON SCREEN DISPLAY MENU SYSTEM If you enter to this menu by MULTI dial on the front panel 5 Press SELECT to show SETUP MENU FL display and press The SR7300 incorporates an on screen menu system which makes ENTER button U ing E 3 Select a desired sub menu with or Y cursor button and press buttons on the remote control unit MULTI FUNCTION dial TUNING the OK button to entr i 4 gt button and ENTER button on the front panel NG dis E 417 Use MULTI FUNCTION dal as Up Down button in remote TUNING lt s eu Se DA par button as Left Right button in remote ENTER button as OK button in remote cursor buttons Notes Notes If you desire to adjust any sub menu you need to set A UNLOCKED To view the on screen displays make certain you have made a 4 f you desire to exit from this menu system press EXIT button or connection from the Monitor Out jack VIDEO or S VIDEO on the rear panel to the composite S Video input of your TV or SELECT button on the front panel or move the cursor to EXIT projector s
26. e Selected function is displayed and LEARN is blinking roca Ss ERRZRE ZRERUZ 4 Select the button to be learned e LEARN is displayed wa d BASS TREBLE 5 Press and hold the button of the original remote controller to learn until OK in the display e When NG is displayed repeat this step e When FULL is displayed the memory of the RC7300SR is full If you want to learn the code you should erase other learned button Hepeat steps 4 and D to learn other buttons in same function Hepeat steps 3 to 6 to learn other function When you have finished programming the remote controller press and hold down the OK button until USE is displayed in the display SOND Note e When NG 15 displayed in step 5 again the transmitting code 15 unavailable for RC7300SR or the transmitting signal is intercepted by noise f no buttons are pressed for approximately 1 minutes while in the LEARN mode the remote controller automatically returns to the use mode ERASING LEARNING CODE Erasing the code by buttons 1 Press and hold down the T MODE and MEMO buttons until LEARN is displayed in the display E TAS on m f AN EAE CIC DO LEIN EE f 2 Select the Function button to select the button to be erased Selected function is displayed and LEARN is blinking e cccg marantz Press and hold down the CL button and press
27. multiroom system in a remote room DC TRIGGER output terminals Connect a device that needs to be triggered by DC under certain conditions screen power strip etc Use the system OSD setup menu to determine the conditions by which these jacks will be active Note This output voltage is for status control only It is not sufficient for drive capability MULTI ROOM REMOTE IN OUT terminals IN Connect to multi room remote control device available from your Marantz dealer OUT Connect to the Marantz component equipped with remote control RC 5 terminals in Multi zone Multi room REMOTE CONT IN OUT terminals Connect to a Marantz component equipped with remote control RC 5 terminals AUDIO IN OUT CD TAPE CD R TV DVD VCR1 DSS VCR2 These are the analog audio inputs and outputs There are 7 audio inputs 4 of which are linked to video inputs and 4 audio outputs 2 of which are linked to video outputs The audio jacks are nominally labeled for cassette tape decks compact disc players DVD players and etc The audio inputs and outputs require RCA type connectors DIGITAL INPUT Dig 1 6 OUTPUT coaxial optical These are the digital audio inputs and outputs There are 3 digital inputs with coaxial jacks 3 with optical jacks The inputs accept digital audio signals from a compact disc LD DVD or other digital source component For digital output there is 1 coaxial output and 1 optical outp
28. of the polarized plug AC POLARIZED PLUG Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product Protective Attachment Plug The product is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure 1 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unp
29. signals from DTS laser disc or CD are playing in another Surround mode you cannot switch to digital input or from digital input to analog input by INPUT SETUP in SETUP MAIN MENU or A D button The outputs for the VCR 1 OUT DSS VCR 2 OUT TAPE OUT and CD R OUT output analog audio signals Do not record from CDs or LDs that support DTS using these outputs If you do the DTS encoded signal will be recorded as noise NOTE for Dolby Digital Surround EX signal When playing Dolby Digital Surround EX encoded software in 6 1 channels it is required to set the EX ES mode Note that some of Dolby Digital Surround EX encoded software does not contain the identification signal In this case set the EX ES mode manually NO TE for 96kHz PCM audio AUTO Source DIRECT and STEREO modes can be used when playing PCM signals with a sampling frequency of 96 kHz such as from DVD Video discs that contain 24 bit 96 kHz audio If such signals are input during playback in one of the other surround modes output from SR7300 will be muted Certain DVD player models inhibit digital output For details refer to the player s operation manual Some DVD formatted discs featured copy protection When using such disc 96 kHz PCM signal is not output from the DVD player For details refer to the player s operation manual NOTE for HDCD signal OSE version only HDCD is effective only at the time of digital input AUTO Source DIRECT and STERE
30. soundtrack will be excessively bright and harsh when played back over audio equipment in the home This is because film soundtracks were designed to be played back in large movie theater environments Activating the HT EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance SPEAKER A B SETUP EXIT OEC CHANNEL SKIP TUNE SEARCH CC REC SPKR A B ATT MULTI ch LQ AAA 5987300 has speaker system and speaker system B to front L R channels You can select these systems by pressing SPEAKERS button on the front panel or SPKR A B on the remote 33 m Z G ay I 7 1 CH INPUT The SR7300 is equipped for future expansion through the use of Multi channel SACD multi channel player or DVD Audio player This is selected the input signals connected to the L front left R front right CENTER SL surround left SR surround right SBL surround back left and SBR surround back right channels of the 7 1 CH In jacks are output directly to the front left and right center surround left and right and surround back left and right speaker systems as well as the pre out jacks without passing through the surround circuitry In addition the signal input to the SW subwoofer jack is output to the PRE OUT SW subwoofer jack When 7 1 CH INPUT is selected the las
31. supplied batteries will be consumed quickly GENERAL INFORMATION OF RC7300SR TO SR7300 To control the SR7300 by your RC7300SR you have to select the device AMP or TUNER by function selector button Please refer as below for the details in AMP and TUNER mode AMP MODE U EX ES 5 csit M CHST v DIR SEAR L U STEREO VIRTUAL DSP 0 8 9 SETUP EXIT CHANNEL 5 TUNE SEARCH gt gt REC SPKR ATT MULTI el gt gt gt Beca ceceg LEARNING REMOTE CONTROLLER RC7300SR POWER ONJOFF Tums tne SA7300 onandof POWERON POWER OFF V OF F EO SLEEP ND DISP RDS Surround mode Selects the surround mode S DIRECT NIGHT 10 MUTE 8455 47 TREBLE AY VOL AY MENUIOSD Cursor OK Enter the On screen display Confirms the setting in On screen display mode ame as OK button alls up SETUP MENU and adjusts speaker levels or 7 1ch input level nters the test tone menu EXIT Exits from SETUP MAIN MENU SETUP CH SEL TEST Moves the cursor for setting in On screen display mode SPKR A B Selects the speaker system ATT educes the input level MULTI urns the multi room mode on or off Function selector Selects a particular source component TUNER MODE 19 JDISP RDS 0 0 M CS M CH ST a DIR SEAR 6 U STEREO 8 DSP H SURR MODE E N aem 0 e 2 2 2 P SCAN MUTE _ DECK A zoe eC H BASS
32. tape recorders for making recordings FM antenna terminal 75 ohms Connect an external FM antenna with a coaxial cable or a cable network FM source AM antenna and ground terminals Connect the supplied AM loop antenna Use the terminals marked AM and GND The supplied AM loop antenna will provide good AM reception in most areas Position the loop antenna until you hear the best COMPONENT VIDEO INPUT OUTPUT If your DVD player or other device has component video connectors be sure to connect them to these component video connectors on the SR7300 The SR7300 has two component video input connectors to obtain the color information Y Cs Cn directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device By sending the pure DVD component video signal directly the DVD signal forgoes the extra processing that normally would degrade the image The result is vastly increased image quality with incredibly lifelike colors and crisp detail Notes This component video output is disable to OSD menu system OUT OUT wae E DEE EP 20W 1A MAX 120 1 MA OUTLE 120V 60HZ PEAKER SY FRONT OR CENTER SURROUND SURR BACK MINIMUM 6 OHM 5 FRONT MINIMUM 8 OHMS 4 RS232C RS232C port is to be used conj
33. the USE mode press and hold down the OK button l until USE is displayed in the display 1 5 seconds 5 seconds 4 Press and hold down the OK button 15 until USE is displayed in the display 45 m Z G ay I 46 If th it d ly check h in th TROUBLESHOOTING EE not operate properly check items shown the In case of trouble check the following before calling for service If your trouble cannot be recovered with the remedy actions listed in 1 Are the connections made properly the following table malfunction of the internal circuitry is suspected immediately unplug the power cable and contact your dealer nearest Marantz distributor or the Marantz Service Center in your country 2 Are you operating the unit properly following user s guide 3 Are the power amplifiers and speaker working properly SYMPTOM CAUSE REMEDY SR7300 cannot be turned up The power plug is not connected Connect the power plug to the outlet No sound and picture are output Mute is on even when power is on The input cable is not connected correctly The master volume control is turned all the way down Adjust the master volume The function selector position is wrong Select correct position Speaker does not outputting any The headphones are connected to the headphone jack Disconnect the headphones Speakers will not output sound when sound headphones are connected Sound and pictures from other
34. the learned button twice to be erased CLR is displayed for 3 seconds and the mode returns to LEARN mode STEREO VIRTUAL _ 05 PTY EH SURR MODE NIGHT S DIRE MEMO cL EM em Le T MODE 4 Toreturn the USE mode press and hold down the OK button until USE is displayed in the display Erasing the code by functions 1 Press and hold down the T MODE and MEMO buttons until LEARN is displayed in the display S DIRECT SURR MODE NIGHT 56 RD fo 1 Ng as WE LEARN Ge 88 000 C mg MENU 2 Press and hold down the CL button and press the learned Function button twice to be erased e F CLR and LEARN are blinking cc eh E 1 SION 3 Press OK button to continue erasing F CLR is displayed for 3 seconds and the mode returns to LEARN mode To cancel the erasing operation do not press OK button and simply touch any other button 4 To return the USE mode press and hold down the OK button until USE is displayed in the display I o 9 2 TT 41 Erasing the all functions 1 Press and hold down the T MODE and MEMO buttons until AIN TIC LAE ENTM AU 2 LEARN is displayed in the display r e L 6 SE Sg 00 MENU Y 2 Press and hold down the CL button and press POWER ON and POWER OFF b
35. the number of macro to be If while programming no buttons are pressed for edited a approximately 1 minute the remote controller will The programmed operation is displayed after the number of automatically return to normal mode and no macro will be macro is displayed programmed in the memory e The number of macro be changed with the cursor A V button CONFIRMING MACROS Torewrite an existing macro step simply press the button for AAO OO TO the new step old step will erased and rewritten with Macros may be confirmed using following procedure the new step e To insert new step in between existing steps in a macro 1 Press and hold the T MODE and MENU button until the MACRO after step 3 press the MEMO button then press the button for is displayed on the LCD E the new step The numbers of the other steps will be adjusted LEARN and MACRO is displayed blinking accordingly to accommodate the new step Since only 10 steps may be stored in any macro the tenth step will be erased if an step is inserted when the total number of steps is already 10 e To erase step in a macro after step 3 call up the number of the step to be erased and press the CL button ES Press the OK button to return step 7 2 Press the Function button to be confirmed To return the USE mode press and hold down the OK button Let s use the example of the DVD player by pressing the DVD until USE is displayed in the display
36. will reset the settings of the function selector Surround mode delay time TUNER PRESET etc to their initial settings I o 9 2 TT 47 ITI Z G ay I Frequency Range 87 5 108 0 MHz Usable Sensitivity IHF 1 8 uV 16 4 dBf Signal to Noise Ratio Mono Stereo 76 72 dB JISLOFHOTI EE Mono Stereo 0 2 0 3 96 Stereo Separation 1 kHz 45 dB Alternate Channel Selectivity 300 kHz 60 dB Image Rejection 98 MHz 70 dB Tuner Output Level 1 kHz 75 kHz Dev 800 mV AM TUNER SECTION Frequency Range 520 1710 kHz Signal to Noise 50 dB Usable Sensitivity Loop 400uV Distortion eeennne 1 kHz 30 96 Mod 0 5 96 Selectivity 202 20 kHz 70 dB AUDIO SECTION Power Output 20 Hz 20 KHz THD 0 08 SR7300 Front LOR E 8 ohms 105 W Ch Center 8 ohms 105 W Ch Surround L amp R EE 8 ohms 105 W Ch Surround 8 ohms 105 W Ch en 6 ohms 130 W Ch 6 ohms 130 W Ch lt del lee L amp R E 6 ohms 130 W Ch lee lee 6 ohms 130 W Ch Power Output 20 Hz 20 kHz THD 0 08
37. 1 61IN SLEEP AUDIO ANGLE SUBTITLE oun AUTO oo DIS DISP RDS M i CHST F DIR SEAR EXIT SEL CHANNEL SKIP TUNE SEARCH REC SPKR ATT MULTI e v He He Cache LEARNING REMOTE CONTROLLER RC7300SR 7 Opens doses the dsc tay Selects the audio language elects the camera angle elects the subtitle language nputs the numeric isplays the disc information earches the title or track ears the inputting alls up programming menu ext disc tray a alls up the menu of the DVD disc oves the cursor enters the settin UBTITLE 9 10 DIR SEAR p A CO 22 ml OO gt gt m ITI m CO ZIZ Y Y SO m TOP MENU MENU OSD Cursor OK ololzlololol ols o CD 3 gt CD J U a CO O DVD player kips forward or previous chapter trac earches forward or backward ause O HI o e CH j CD CD F 3 CD 3 O 2 F 5 A CD U re CONTROLLING A MARANTZ VCR VCR1 MODE USE IF E34 1 VILIS I a V OFF EQ 71 61IN SLEEP AUDIO ANGLE SUBTITLE A D DTS DISP RDS EH ST F_DIR SEAR STEREO VIRTUAL DSP PTY 8 9 MEMO IRECT SURR MODE NIGHT 0 10 INPUT T MODE P SCAN MUTE SETUP EXIT goce CHANNEL SKIP TUNE SEARCH 000a REC SPKR A B ATT MULTI
38. 6 CS II PARAMETER 9 2 DC TRIGGER SETUP DC TRIG 2 DISABLE TRUBASS PARAMETER DEFAULT SRS DIALOG CD OFF TV TAPE OFF DVD PANORAMA CD R OFF VCR1 DIMENSION TUNER OFF DSS CENTER WIDTH AUX1 OFF AUX2 OFF MAIN RETURN m Z G E ay I 1 INPUT SETUP ASSIGNABLE DIGITAL INPUT Six digital inputs can be assigned as the desired source Use this menu to select the digital input jack to be assigned to the input source 1 Select INPUT SETUP in SETUP MAIN MENU with A or Y cursor button and press the OK button 1 INPUT SETUP D6 AT TV ANA DVD D1 AT VCR1 DSS AUX 1 To select the input source press A or V cursor button To select the digital input jack press the 4 or gt cursor buttons Select Dx AT for input sources for automatic detection of the digital input signal condition If no digital signal is input the input signals to the analog input jacks will be played Select Dig x for input sources for fixed the digital input jack Select ANA for input sources for which no digital input jacks are used 4 i you finish the setup in this sub menu move cursor to MAIN with A or V cursor buttons and press OK button Notes The TUNER is fixed to the analog input and cannot be selected for any digital input e When a DTS LD or DTS CD is playing this setup is not available This is to avoid noise being generated from the analog input If Dx AT is selecte
39. AVIA ITM Company Omladinskih Brigada 86 11070 Belgrade Yugoslavia www marantz com Manufactured under license from Dolby Laboratories Laboratories Confidential Unpublished Works 1992 1997 Dolby Laboratories Inc All rights reserved Manufactured under license from Digital Theater Systems Inc US Pat No 5 451 942 and other worldwide patents issues and pending Dolby AC 3 Pro Logic and the double D symbol are trademarks Dolby Drs and DTS Digital Surround are trademarks of Digital Theater Systems Inc 1996 Digital Theater Systems Inc All rights reserved 9 HDCDS High Definition Compatible Digital and Pacific Microsonics are either registered trademarks or trademarks of Pacific Microsonics Inc in the United States and or other countries HDCD system manufactured under license from Pacific Microsonics Inc This product is covered by one or more of the following In the USA 5 479 168 5 638 074 5 640 161 5 808 574 5 838 274 5 854 600 5 864 311 5 872 531 and in Australia 669114 Other patents pending Printed in Japan ERRA A Been BRE 27 5 a registered trademark 12 2002 MITi O38AJ851260
40. O modes can be used when playing HDCD signals such as from CD discs that contain HDCD You may not be able to play some HDCD source signals from certain CD players if you connect the player to the SR7300 OSE digitally This is because the digital signal has been processed such as the output level sampling frequency or frequency response and the SR7300 OSE cannot recognize the signal as HDCD data The relation between the selected surround mode and the input signal The surround mode is selected with the surround mode selector on SR7300 the relationship between the selected surround mode and input signal That or the remote control unit However the sound you hear is subject to relationship is as follows Front information display Output Channel Surround Mode Input Signal Decoding URIC SL SB SR bW AUTO Dolby Surr EX Dolby Digital EX O O Channel status L C R SL SR S LFE Signal format indicators DIGITAL Dolby D 5 1ch Dolby Digital 5 1 DIGITAL obo A LFE Dolby D 2ch Dolby Digital 2 0 DIGITAL Dolby D 2ch Surr Pro Logic II movie DIGITAL SURROUND DTS ES DTS ES dts ES DTS 96 24 DTS 96 24 dts 96 24 DTS 5 1ch DTS 5 1 dts PCM Audio PCM Stereo PCM PCM 96kHz PCM 96kHz Stereo PCM HDCD Stereo HDCD Analog Stereo S DIRECT Dolby D
41. OSD information on the video display The input name will also appear in the display on the front panel As the input is changed the SR7300 will automatically switch to the digital input surround mode attenuation and night mode status that were entered during the configuration process for that source e When an audio source is selected the last video input used remains routed to the VCR1 amp VCR2 Outputs and Monitor Outputs This permits simultaneous viewing and listening to different sources When a Video source is selected the video signal for that input will be routed to the Monitor Outputs jack and will be viewable on a TV monitor connected to the SR7300 If a component video input is connected to the DVD or DSS component inputs it will be routed to the Component Video Output Make certain that your TV is set to the proper input to view the signal SELECTING THE SURROUND MODE E G AUTO SURROUND DTS DISP RDS Do lt gt 5 n DIR SEAR 6 U STEREO VIRTUAL 05 E E C COS To select the surround mode during playback turn the SELECT knob on the front panel or press the surround mode button on the remote ADJUSTING THE MAIN VOLUME Adjust the volume to a comfortable level using the VOLUME control knob on the front pan
42. RIG 1 DISABLE CD OFF TV TAPE OFF DVD CD R OFF VCR1 TUNER OFF DSS AUX1 OFF AUX2 OFF MAIN NEXT EXIT N You can select MAIN ROOM MULTI ROOM or DISABLE by pressing lt or gt cursor buttons To Select desired input source press or V cursor button To set ON or OFF press 4 or gt cursor button If you finish the setup to DC 1 trigger move cursor to NEXT with A or V cursor buttons and press OK button to go to next page AL 9 2 DC TRIGGER SETUP DC TRIG 2 DISABLE CD OFF TV TAPE OFF DVD CD R OFF VCR1 TUNER OFF DSS AUX1 OFF AUX2 OFF MAIN RETURN D You can select MAIN ROOM MULTI ROOM or DISABLE by pressing lt or gt cursor buttons To Select desired input source press A or V cursor button To set ON or OFF press lt or gt cursor button If you finish the setup to these menu move cursor to MAIN with A or V cursor buttons and press OK button ODN 26 BASIC OPERATION Wa SELECTING AN INPUT SOURCE Before you can listen to any input media you must first select the input source at the SR7300 E G DVD REC SPKR A B ATT MULTI To select DVD simply press the DVD button on the front panel press DVD button on the remote After you have selected DVD simply turn on the DVD player and play the DVD As the input source is changed the new input name will appear momentarily as an
43. Surr EX Dolby Digital EX ANALOG DIGITAL Dolby D 5 1ch Dolby Digital 5 1 DIGITAL Dolby D 2ch Dolby Digital 2 0 DIGITAL Dolby D 2ch Surr Pro Logic II movie DIGITAL SURROUND DTS ES DTS ES dts ES DTS 96 24 DTS 96 24 dts 96 24 DTS 5 1ch DTS 5 1 dts PCM Audio PCM Stereo PCM PCM 96kHz PCM 96kHz Stereo PCM HDCD Stereo PCM HDCD Analog Stereo EX ES Dolby D Surr EX Dolby Digital EX ANALOG DIGITAL Dolby D 5 1ch Dolby Digital EX DIGITAL DTS ES dts ES DTS 5 1ch DTS ES Dolby D Surr EX Dolby Digital 5 1 DOLBY dts DIGITAL PL II movie PL II music Pro Logic Dolby D 5 1ch Dolby Digital 5 1 DIGITAL Dolby D 2ch Pro Logic II DIGITAL Dolby D 2ch Surr Pro Logic II DIGITAL OO SURROUND PCM Audio Pro Logic II PCM Analog Pro Logic II DTS DIS ES DIS 5 1 ANALOG dts ES Neo 6 Cinema DTS 96 24 DTS 96 24 dts 96 24 Neo 6 Music DTS 5 1ch DTS 5 1 dts PCM Audio Neo 6 PCM Analog Neo 6 ANALOG Neo 6 DIGITAL Dolby D 2ch D Neo 6 PCM Audio DIGITAL OO SURROUND PCM Analog ANALOG Dolby D 2ch DIGITAL
44. TREBLE VOL A 12 TOP MENU MENU 0SD SETUP EXIT E CHANNEL 5 TUNE SEARCH REC SPKR ATT MULTI 2 LEARNING REMOTE CONTROLLER 09 Inputs the numeric 00 Selects the display mode in RDS Displays the program type information of the current station CHANNEL SKIP Selects a preset station 9 European model only I o 2 TT 13 m Z G T I CONNECTIONS SPEAKER PLACEMENT The ideal surround speaker system for this unit is 7 speaker systems using front left and right speakers a center speaker surround left and right speakers a surround back and a subwoofer For best results we recommend that all front speakers be of the same type with identical or similar driver units This will deliver smooth pans across the front sound stage as the action moves from side to side Your center channel speaker is very important as over 80 of the dialog from a typical motion picture emanates from the center channel It should possess similar sonic characteristics to the main speakers Surround channel speakers need not be identical to the front channel speakers but they should be of high quality The surround center speaker is useful for playback of Dolby Digital Surround EX or DTS ES One of the benefits of both Dolby Digital AC 3 and DTS is that surround channels are discrete full range while they were fre
45. TT m Z G ay I 3 AUX1 input jacks These auxiliary video audio and optical digital input jacks accept the connection of a camcorder portable DVD game etc INPUT FUNCTION SELECTOR buttons AUDIO VIDEO These buttons are used to select the input sources The video function selector such as TV DVD VCR1 DSS and AUX1 selects video and audio simultaneously Audio function sources such as CD TAPE CDR MD TUNER and AUX2 may be selected in conjunction with a Video source This feature Sound Injection combines a sound from one source with a picture from another Choose the video source first and then choose a different audio source to activate this function Press TUNER button to switch the between FM or AM 5 SPEAKERS A B button Press these buttons to select speakers systems A and or B 7 1CH IN button Press this button to select the output of an external multi channel decoder 4 A D Analog Digital SELECTOR button This is used to select between the analog and digital inputs Note e This button is not used for an input source that is not set to digital input in the system setup menu S Source DIRECT button When this button is pressed the tone control circuitry is bypassed as well as Bass Management Notes The surround mode is automatically switched to AUTO when the source direct function is turned on e Additionally Speaker Configurations are fixed automatically as follow Fr
46. To select a desired content press A or V cursor button SURR MODE Select the desired surround mode with lt or gt cursor button 24 HT EQ Select to active the HT EQ with lt or gt cursor button The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home This is because film soundtracks were designed to be played back in large movie theater environments Activating the HT EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance The HT EQ feature can be activated only while in Dolby Pro Logic Mode or while decoding Dolby Digital or DTS encoded material LFE LEVEL Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal Select 0 dB 10 dB or OFF with Left or Right cursor button CHANNEL LEVEL CENTER LEVEL Set the effect level of the center speaker between 10 and 10 dB level in 1 dB level interval If None was selected for the Center speaker setting in the Speaker size then this setting will not appear SURR L LEVEL Set the level of the Surround left speaker between 10 and 10 dB level in 1 dB level interval f None was selected for the Surround left speaker setting in the Speaker size then this setting will not appear SURR R LEVEL Set the level of the Surround speaker between 10 and 10 dB level in 1 level interval If N
47. UNER button 2 The tuning mode can be changed by MODE button 4 If no button is pressed during this period the current station is memorized in location Preset 02 If you wish to skip the current station press the TUNING P button during this period this station is skipped and auto presetting continues 5 Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands If you desire to stop the auto preset memory at anytime press the CLEAR button Using the SR7300 1 Tune into the radio station you desire Refer to the MANUAL TUNING or AUTO TUNING section Press the MEMORY button on the front panel preset number starts blinking on the display Select the preset number by pressing the TUNING lt or gt button while this is still blinking approx 5 seconds Press the MEMORY button again to enter The display stops blinking The station is now stored in the specified preset memory location N Using the remote control unit Tune into the radio station you desire Refer to the MANUAL TUNING or AUTO TUNING section 2 Press the MEMO on the remote unite preset number starts blinking on the display 3 Enter the desired preset number by pressing numeric buttons Note e When entering a single digit number 2 for example either input 02 or just input 2 and wai
48. alog input jacks for the selected input source are detected automatically If no digital signal is being input the analog input jacks are selected automatically In Digital mode input is fixed to an assigned digital input terminal In analog mode the analog input jacks are selected This selecting is temporarily so the result will not be stored in memory If you need to change input mode completely use SYSTEM SETUP in OSD menu system see page 22 RECORDING AN ANALOG SOURCE In normal operation the audio or video source selected for listening through the SR7300 is sent to the record outputs This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT CD R MD OUT VCR1 OUT DSS VCR2 OUT in the record mode To record the input source signal you are currently watching or listening to CHANNEL 5 TUNE SEARCH Ce on C lt gt lt gt gt 1 eee 1 Select the input source to record by pressing the corresponding input selector button The input source is now selected and you may watch or listen to it as desired 2 Outputs the currently selected input source signal to the TAPE OUT CD R MD OUT VCR1 OUT and DSS VCR2 OUT outputs for recording J Start recording at the recording component as desired Recording the video
49. are Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn wu mdp Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 12 13 14 15 16 17 18 19 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose
50. cceptable listening quality ST Stereo This indicator illuminates when an FM station is being tuned in stereo condition 6 DTS ES mode indicators DISC6 1 MTX6 1 These indicators will show to DIS ES decoding mode Discret 6 1 or Matrix 6 1 7 V video OFF mode indicator This indicator lights when the Video OFF function is active 8 NIGHT mode indicator This indicator lights when the SR7300 is in the Night mode which reduces the dynamic range of digital program material at low volume levels 9 SPKR speaker AB indicator Active speaker system will be shown by this indicator I o 9 2 TT 10 PEAK indicator This indicator is a monitor for an analog audio input signal If the selected analog audio input signal is greater than the capable level of internal processing this will light If this happens you should press the ATT button 11 EQ mode indicator This indicator lights when the HT EQ function is active 12 ATT Attenuation indicator This indicator lights when the attenuation function is active 13 DIGITAL Input Indicator This indicator lights when digital input has been selected 14 ANALOG input indicator This indicator lights when an analog input source has been selected 15 SIGNAL FORMAT indicators DIGITAL EX SURROUND dts ES 96 24 PCM When the selected input is a digital source some of these indicators will light to display the specific type of si
51. ce may result in a decrease of the actual volume of the low frequency range e Selection of the MIX will play the low frequency signal range of the channel selected with LARGE from that channel only Therefore the low frequency signal range that are played from the subwoofer channel are only the low frequency signal range of LFE only during Dolby Digital or DTS signal playback and the channel specified as SMALL in the setup menu 2 2 SPEAKER DISTANCE Use this parameter to specify the distance of each speaker s position from the listening position The delay time is automatically calculated according to these distances Begin by determining the ideal or most commonly used seating position in the room This is important for the timing of the acoustics to create the proper sound space that the SR7300 and today s sound systems are able to produce Note that the speakers that you selected None for in the Speaker Config sub menu will not appear here There are several useful books and special DVD and LD s available to guide you through proper home theater configuration If you are unsure have your Marantz dealer perform the installation for you They are trained professionals familiar with even the most sophisticated custom installations Marantz recommends the WWW CEDIA ORG website for further information about this 2 2 SPEAKERS DISTANCE FRONT L 10 ft FRONT R 10 ft CENTER 10 ft SURR L 10 ft SURR R 10 ft SUB W
52. close to the point of cable entry as practical NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica tions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help NOTE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards There are however so
53. d CD players performing operations such as Skip or Stop may momentarily interrupt the output When the signal is not decoded is input for using mode the mode is changed to AUTO mode automatically Refer to page 3 to confirm the available decoding mode MODE Dolby Digital Pro Logic MOVIE Pro Logic Il MUSIC Pro Logic This mode is used with source materials encoded in Dolby Digital and Dolby Surround DOLBY DIGITAL This mode is enabled when playing source materials encoded in Dolby Digital Playing multi channel encoded 5 1 channel Dolby Digital sources provides five main audio channels left center right surround left and surround right and Low Frequency Effect channel Dolby Digital EX decoding is not available in this mode Dolby Pro Logic Il brings the excitement of surround sound to any stereo mix while making existing Dolby Surround mixes sound more like discrete 5 1 channels Surround sound Dolby Pro Logic II has below modes Pro Logic Il MOVIE This mode provides 5 1 channel surround sound from Dolby Surround encoded stereo movie sound tracks Pro Logic MUSIC This mode provides 5 1 channel surround sound from conventional stereo sources analog or digital such as CD tape FM TV stereo VCR etc Pro Logic This mode emulated original Dolby Pro Logic decoding 3 1 surround suit for Dolby Surround encoded stereo movie soundtracks Notes Pro Logic II mode is available
54. d and a DVD compact disc or LD is fast forwarded during playback decoded signals may produce a skipping sound In such cases change the setting to DIGITAL CN 2 SPEAKER SETUP After you have installed the SR7300 connected all the components and determined the speaker layout it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout Before you perform the following settings it is important that you first determine the following characteristics 2 1 SPEAKER SIZE When setting the speaker size in the SPEAKER SIZE sub menu use the guidelines given below Large The complete frequency range for the channel you are setting will be output from the speaker Small Frequencies of the channel you are setting lower than approx 100 Hz will be output from the subwoofer If the Subwoofer is set to NONE and the front speakers are set to Large then the sound may be output from both the left and right speakers 2 1 SPEAKERS SIZE SUBWOOFER YES FRONT L R LARGE CENTER SMALL SMALL SURROUND L R SURR BACK 1CH SURR BACK SIZE LPF HPF 100 HZ BASS MIX BOTH MAIN NEXT EXIT SMALL 22 Select SPEAKER SETUP in MAIN SETUP MENU with Up or Down cursor button and press the OK button To select the each speaker press Up or Down cursor button To select the setting of size to each speaker press the Left or Right cursor button
55. e This function reduces the voice by 1 3 to 1 4 at maximum Thus it eliminates the occurrence of an abruptly loud voice at night However the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back When this button is pressed NIGHT indicator lights up PTY button European model onty when TUNER mode is selected Used to display the programme type information of the current station The RDS system categorizes programmes according to their genre into different programme type PTY groups F DIR SEAR button when TUNER mode is selected Used to select the mode of frequency direct input DISP RDS button when TUNER mode is selected European model only Selects display mode function in RDS Radio Data System by this button when AMP mode is selected Selects the display mode for the front display of the SR7300 A D button This is used to switch between the analog and digital inputs SLEEP sleep timer button This button is used for setting the sleep timer It can be operated the same way as the button in unit 7 1 6 1CH IN button Press this button to select the output of an external multi channel decoder POWER ON OFF buttons when AMP mode is selected Press to switch the power of the SR7300 ON or OFF 11 m Z G ay I 12 LCD Liquid Crystal Display Information about cur
56. ed on the LCD LEARN and MACRO is displayed blinking S DIRECT SURR MODE NIGHT MEMO INPUT T MODE P SCAN MUTE M e LEARN MACRO AMISIT Ei U ILIN N 2 Press the DVD Function button Here the DVD Function button is used as the macro button but any function button can in fact be used TDO po Sa i CEARN MACRO sas Hy DU fl NHRERZRE ZREREZ BNINA REMATE CONTRAI I J Tosetthe various steps of the macro press the following buttons in order 1 2 POWER ON gt 3 DVD 4 AMP 5 8 VIRTUAL 6 DVD gt 7 POWER on OWER ON OFF a LEARN MACR 0 Kl 040 AWN TZ AN V OFF CO X Ze Ur es n Quo c AWN EE Mere UC 486 n 00 _ SE n e SR JH Ne cx n E Ex 60 LEARNING REMOTE _ eo AWN TZ tly tt 4 When you are finished programming the macro press the OK button until the display returns to USE mode Now execute the macro you just programmed 1 Press the DVD Function button for 3 seconds The macro commands are transmitted in order and the steps of the operations are displayed on LCD in order USE LIMI When executing this macro function operations and DVD only switch the c
57. ee 17 page and press the OK button SETUP MAIN MENU INPUT SETUP UNLOCK SPEAKER SETUP UNLOCK PREFERENCE UNLOCK SURROUND UNLOCK PRO LOGIC UNLOCK CS I UNLOCK MULTI ROOM UNLOCK 7 1 CH IN UNLOCK DC TRIG SETUP UNLOCK EXIT OMAN Oa P GA 1 INPUT SETUP 2 1 SPEAKERS SIZE 7 MULTI ROOM MULTI ROOM OFF CD D6 AT TV SUBWOOFER YES TAPE ANA DVD FRONT L R LARGE VIDEO DVD CD R D1 AT VCR CENTER SMALL AUDIO DVD DSS SURROUND L R SMALL VOLUME SETUP VARIABLE AUX1 SURR BACK 1CH VOLUME LEVEL 90 dB SURR BACK SIZE SMALL SLEEP TIMER OFF LPF HPF 100 HZ MAIN ROOM STATUS BASS MIX BOTH VIDEO DVD AUDIO DVD MAIN NEXT EXIT MAIN EXIT 3 PREFERENCE 2 2 SPEAKERS DISTANCE 8 7 1 CH INPUT LEVEL STANDBY MODE ECONOMY FRONT L 10 ft e FRONT L TV AUTO DISABLE FRONT R 10 ft CENTER OSD INFO ENABLE CENTER 10 ft 2 FRONT R SURR L 10 ft SURR R SURR R 10 ft SURR B R SUB W 10 ft SURR B L SURR BACK 10 ft i SURR L SUB W MAIN RETURN NEXT EXIT MAIN OO OO OO OH 4 SURROUND 2 3 SPEAKERS LEVEL 9 1 DC TRIGGER SETUP SURR MODE AUTO TEST MODE MANUAL DC TRIG 1 DISABLE HT EQ FRONT L 0 dB LFE LEVEL CENTER dB CD OFF TV CENTER FRONT R dB TAPE OFF DVD SURR L SURR R dB CD R OFF VCR1 SURR R SURR BACK dB TUNER OFF DSS SURR BACK AUX1 OFF SURR L dB AUX2 OFF SUB W SUB W dB MAIN MAIN RETURN EXIT MAIN 5 PLI MUSIC PARAMETER
58. el or VOL A V buttons on the remote To increase the volume turn the VOLUME knob to the clockwise or press VOL A button on the remote to decrease the volume turn to the counterclockwise or press VOL V button on the remote Notes The volume can be adjusted within the range of to 18 dB in steps of 1 dB However when the channel level is set as described on page 25 if the volume for any channel is set at 1 dB or greater the volume cannot be adjusted up to 18 dB In this case the maximum volume adjustment range is 18 dB Maximum value of channel level ADJUSTING THE TONE BASS amp TREBLE CONTROL During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics using the SR7300 To change the selector mode press SELECT button until BASS or TREBLE is shown on front display Turn the SELECTOR knob to desired level of tone control Using the remote control unit To adjust the bass effect press BASSA or 557 on the remote To adjust the treble effect press TREBLEA or TREBLEV on the remote Notes The tone control function can work in the AUTO Surround Stereo Dolby PL2 DTS DTS ES and Multi Ch Stereo mode ENGLISH 27 m Z G 70 I TEMPORARILY TURNING OFF THE SOUND OR STEREO VIRTUAL DSP
59. ete connections may make noise Be sure to connect the left and right channels properly Red connectors are for the R right channel and white connectors are for the L left channel Be sure to connect input and output properly Refer to the instructions for each component that is connected with this unit Do not bind audio video connection cables with power cords and speaker cables will result in generating hum or other noise CONNECTING DIGITAL AUDIO COMPONENTS 16 There are 6 digital inputs 3 coaxial jacks and 3 optical jacks on the rear panel You can use these jacks to input PCM Dolby Digital and DTS bitstream signals from a CD DVD or other digital source components There are one digital output with coaxial jack and one with optical jack on the rear panel These jacks can be connected to CD recorder MD deck DIGITAL AUDIO COAXIAL coe auct Je DIGITAL AUDIO OPTICAL alll e Setup the digital audio format of DVD player or other digital source component Refer to the instructions for each component to be connected to digital input jacks Use fiber optical cables optical for DIG 1 2 3 input jacks Use 75 ohms coaxial cables for digital audio or video for DIG 4 5 6 input jacks You can designate the input for each digital input output jacks according to your component See page 22 Notes There is no Dolby
60. from one source and the audio from another You can add the sound from one source to the video of another source to make your own video recordings Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to AUX1 IN to video cassette tape in a video cassette recorder connected to the VCR1 OUT jack 1 2 5 TUNE SEARCH 555 REC SPKR A B ATT MULTI Zong 1 Press the AUX1 input source button to set video output Press the CD input source button to set audio output 3 Now CD has been selected as the audio input source and AUX1 as the video input source Notes If you change the input source during recording you will record the signals from the newly selected input source You cannot record the surround effects Digital input signals are only output to the digital outputs There is no conversion from digital to analog When connecting CD players and other digital components do not connect only the digital terminals but the analog ones as well ON OFF UN urr CARO O V OFF 1 6 1 IN SLEEP AUDIO UBTITLE A D OX C C A DT 5 DISP RDS I o 9 2 TT EX ES CSH HST FDIR SEAR INPUT T MODE P SCAN MUTE Press the EQ button on the remote to turn on the HT EQ mode The tonal balance of a film
61. ge digital sound reproduction The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters Now every moviegoer can hear the sound exactly as the moviemaker intended DTS can be enjoyed in the home for either movies or music on of DVD s LD s and CD s DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems Inc dts W The advantages of discrete multichannel systems over matrix are well known But even in homes equipped for discrete multichannel there remains a need for high quality matrix decoding This is because of the large library of matrix surround motion pictures available on disc and on VHS tape and analog television broadcasts The typical matrix decoder of today derives a center channel and a mono surround channel from two channel matrix stereo material It is better than a simple matrix in that it includes steering logic to improve separation but because of its mono band limited surround it can be disappointing to users accustomed to discrete multichannel Neo 6 offers several important improvements as follow Neo 6 provides up to six full band channels of matrix decoding from stereo matrix material Users with 6 1 and 5 1 systems will derive six and five separate channels respectively corresponding to the standard home theater speaker layouts Neo
62. gnal in use 6 ENCODED CHANNEL STATUS indicators These indicators display the channels that are encoded with a digital input signal If the selected digital input signal is Dolby Digital 5 1ch or DTS 5 1ch L R 51 SR and LFE will light up If the digital input signal is 2 channel PCM audio L and R will be displayed If Dolby Digital 5 1ch signal with Surround EX flag or DTS ES signal comes L SL 5 SR and LFE will show 7 Main Information Display This display shows messages relating to the status input source surround mode tuner volume level or other aspects of unit s operation 8 DIRECT Source direct indicator This indicator lights when the SR7300 is in the SOURCE DIRECT mode 9 HDCD indicator OSE version only When HDCD signal is decoded this indicator will light up m Z G 70 I REAR PANEL COMPONENT VIDEO VCR2 1 VIDEO IN OUT TV DVD VCR1 DSS VCR2 These are the video inputs and outputs There are 4 video inputs and 2 video outputs and each one includes both composite video and S video configurations Connect VCRs DVD players and other video components to the video inputs S video sources can be viewed through the S video outputs and composite sources can only be viewed through the composite output The 2 video output channels can be used to be connected to video
63. hannels and a sixth 1 channel for low frequency effects Dolby Surround Pro Logic 11 is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround program material provides a convincing three dimensional soundfield on conventional stereo music recordings and is ideally suited to bring the surround experience to automotive sound While conventional surround programming is fully compatible with Dolby Surround Pro Logic decoders soundtracks will be able to be encoded specifically to take full advantage of Pro Logic playback including separate left and right surround channels Such material is also compatible with conventional Pro Logic decoders Dolby Digital EX creates six full bandwidth output channels from 5 1 channel sources This is done using a matrix decoder that derives three surround channels from the two in the original recording For best results Dolby Digital EX should be used with movies soundtracks recorded with Dolby Digital Surround EX Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories CSI by SRS Circle Surround II CS II is a powerful and versatile multi channel technology CS II is designed to enable up 6 1 multi channel surround sound playback from mono stereo CS encoded sources and other matrix encoded sources In all cases the decoder extends it into
64. he display The ST indicator lights on when a stereo broadcast is tuned in At open frequencies the noise is muted and the TUNED and ST indicators turn off If the signal is weak it may be difficult to tune into the station in stereo In such a case press the MODE button on the front panel or press T MODE button on the remote AUTO indicators turn off FM stereo broadcasts are received in monaural and the ST indicator turns off To return to auto stereo mode press the MODE button or press T MODE button on the remote again AUTO indicator lights on the display PRESET MEMORY With this unit you can preset up to 50 FM AM stations in any order For each station you can memorize the frequency and reception mode if desired AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory 5 2 2 4 3 3 1 3 1 1 To select FM press the TUNER button on the front panel 2 While pressing the MEMORY button press the TUNING button to up AUTO PRESET will appear on the display and scanning starts from lowest frequency 35 m Z G ay I J Each time the tuner finds station scanning will pause and the station will be played for five seconds During this time the following operations are possible 1 The band can be changed by T
65. he supplied AM loop antenna The supplied AM loop antenna is for indoor use only Set it in the direction and position where you receive the clearest sound Put it as far away as possible from the unit televisions speaker cables and power cords If you experience poor reception quality an outdoor antenna may improve the quality 1 Press and hold down the lever of the AM antenna terminal 2 Insert the bared wire into the antenna terminal J Release the lever CONNECTING AN FM OUTDOOR ANTENNA Notes Keep the antenna away from noise sources neon signs busy roads etc Do not put the antenna close to power lines Keep it well away from power lines transformers etc To avoid the risk of lightning and electrical shock grounding is necessary CONNECTING AN AM OUTDOOR ANTENNA An outdoor antenna will be more effective if it is stretched horizontally above a window or outside Notes Do not remove the AM loop antenna To avoid the risk of lightning and electrical shock grounding is necessary 19 CONNECTING FOR THE MULTI ROOM m Z G E ay I Same source as the main room LEFT PEKER SPEAKER l MULTIROOM MULTIROOM MULTIROOM LEFT RIGHT SPEAKER SPEAKER i RC IN FRONT cS MAIN AMP H For MULTIROOM i IR RECEIVER i VIDEO IN COS ES O ED
66. his happens you should press the ATT button on the front panel or on the remote ATT indicator will light up when this function is activated The signal input level is reduced by about the half Attenuation will not work with the output signal of TAPE OUT CD R MD OUT VCR1 OUT VCR2 OUT and MULTI ROOM OUT This function is memorized for each individual input source LISTENING OVER HEADPHONES This jack may be used to listen to the SR7300 s output through a pair of headphones Be certain that the headphones have a standard 1 4 stereo phone plug Note that the main room speakers will automatically be turned off when the headphone jack is in use Notes When using headphones the surround mode will automatically change to STEREO The surround mode returns to the previous setting as soon as the plug is removed from the jack 32 VIDEO ON OFF When no video signals of a DVD etc are connected to the SR7300 or the DVD etc are connected directly to a TV the unnecessary video circuit can be turned off by selecting the VIDEO OFF setting To select video off condition press the V OFF on the remote Notes that VIDEO OFF will not work with the output signal of MULTI ROOM OUT ON OFF A UN SOO V OFF EQ 7 1 6 1 IN SLEEP AUDIO ANGLE SUBTITLE A D AUTI D TS DISP RDS EX ES CS M CHST FpIR SEAR KEE DSP STEREO VIRTUAL PTY 07 N 0
67. inuously clean and stable power into each of the six channels It employs a massive El power transformer in combination with oversized filter capacitors Current feedback topology allows total operation stability while requiring minimal amounts of negative feed back resulting in an excellent transient frequency response and superb sonic transparency This design configuration is capable of a clear and powerful reproduction of the most demanding action movie soundtracks and full range multi channel music discs Through its ability to generate very high output voltages the SR7300 can easily drive the most demanding speakers with optimum results The SR7300 incorporates the most advanced Digital Signal Processing circuitry along with a Crystal 192 kHz 24 bit D A converter in each of the 8 channels Independent power supply circuits are incorporated for the FL display audio and video sections for maximum separation clarity and dynamic range Together with hand selected customized components all elements work in harmony to recreate the emotion exactly as the artist had intended The SR7300 is designed and engineered with extensive feedback from custom installation experts dealers and consumers It features multi room multisource 2 assignable DC triggers a RS232C communication port heavy duty speaker binding posts and an extensive array of both analog and digital inputs outputs With 6 assignable digital inputs 7 total 2 component in
68. k on a CD in the CD player 1 Press and hold the T MODE and MENU button until the MACRO is displayed on the LCD e LEARN and MACRO is displayed blinking 122 1 p LEARN MACRO AMI Ei III 2 Press the CD Function button CD M is displayed on the LCD MOG 60 Leien 2 sl y LEARN MACRO AVS Cha LU dd Ki Press CD and gt buttons 2 AUTO 2 3 1 csy 5 5 ERT E DIR SEAR O A07 STEREO DSP PTY SS 48 S DIRECT SURR MODE NIGHT MEMO SOR SUR ED INPUT T MODE P SCAN MUTE DECK LEARN MACRO SETUP CHSEL CHANNEL SKIP 5 3 SUS 4 When you are finished programming the macro press the OK button until the display returns to USE mode We 4 Y Y MENU MENU Now execute the macro you just programmed 1 Press the CD Function button for seconds e The macro commands are transmitted to the components order and the steps of the operations are displayed on the LCD in order 4 4 2 Turn the main amplifier ON Change the amplifier s input source to DVD gt Set the Surround mode to VIRTUAL Set the DVD player to PLAY 1 Press and hold the T MODE and MENU button until the MACRO is display
69. ker terminals when the power is on It may cause electric shocks e Do not connect more than one speaker cable to one speaker terminal Doing so may damage this unit Note e Be sure to connect the positive and negative cables for the speaker properly If they are miss connected the signal phase will reversed and the signal quality will be corrupted Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer power amplifier built in If your subwoofer is passive type power amplifier is not built in connect a monaural power amplifier to the PRE OUT SUBWOOFER Banana plug connections are also possible jack and connect the subwoofer to the amplifier Tighten the knob by turning clockwise and then insert the banana plug 15 m Z G 70 I CONNECTING AUDIO COMPONENTS CD RECORDER MD DECK DIGITAL OUT OUTPUT DIGITAL DIGITAL INPUT OUTPUT i gt TAPE DECK C3 oor CD PLAYER O T C emm The output audio signal from the TAPE OUT jack and the CD R MD OUT jack is the sound source currently selected Caution Do not connect this unit and other components to mains power until all connections between components have been completed Notes Insert all plugs and connectors securely Incompl
70. lug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product xo 20 Servicing Do not attempt to service this product yourself as 22 opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 21 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the 23 following conditions a When the power supply cord or plug is damaged 24 b If liquid has been spilled or objects have fallen into the product c If the product has been exp
71. macro mode the number of steps the macro is displayed the following selected function name e Macros may be programmed for each of the 12 function buttons as follows TV DVD VCR1 DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP 1 Press and hold the T MODE and MENU button until the MACRO is displayed MACRO and LEARN indicators are displayed blinking on the LCD too AN MINIT EN III Press the Function button for which you wish to program a series of operations In this case let s use the example of the DVD player Press the DVD Function button The LCD will display DVD M foo oo NEM 6 lt gt 1 Jeu weg kel Characters displayed LCD include the following depending on the function button for which the macro is being programmed TV M DVD M VCR M DSS M TUN M CD M CDR M MD M TAP M AX1 M AX2 M AMP M If a macro has already been set for the selected function button the LCD will blink Press the buttons for the operations you wish to program as a macro in the sequence you want the macro to program them For example press DVD PLAY The number of steps in the macro is displayed on LCD and this number increases by 1 with each button pressed e Each function button can be programmed to perform up to 10 steps in sequence GCR LC lee Gees E lele HRRZRE ZRERUZ
72. me installation and operation precautions which you should be particularly aware of 1 10 11 Read Instructions All the safety and operating instructions should be read before the product is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the product and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A product and cart combination should be moved with c
73. o disc player with the Dolby Digital RF output jack to the digital input jack on this unit ENGLISH 17 ADVANCED CONNECTING m Z G E 70 I DVD AUDIO PLAYER or SACD MULTI CHANNEL PLAYER SUr R SURR gt gt gt CONNECTING MULTI CHANNEL AUDIO SOURCE The 7 1CH INPUT jacks are for multi channel audio source such as SACD multi channel player DVD audio player or external decoder If you use these jacks switch on 7 1CH INPUT and setup 7 1CH INPUT level by using SETUP MAIN MENU See page 26 CONNECTING REMOTE CONTROL JACKS MD DECK CD RECORDER gp rau RR Ld 18 Bez EDR lon EDR Om B B CENTER SUR SU BACK WOOFER POWER AMPLIFER Subwoofer Surround Left Surround Surround Back Left Back Right CONNECTING EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers you can have better sound quality Be sure to connect each speaker to the corresponding external power amplifier You can control other Marantz products through this unit with the remote controller by connecting REMOTE CONTROL terminals on each unit The signal
74. o is input With Dolby Digital and DTS sources the 5 1 multi channels are converted to two channel stereo 96 kHz PCM source material can be playback in stereo mode HDCD source material can be played in this mode OSE version only S SOURCE DIRECT In the source direct mode the tone control circuit and bass management configuration are bypassed for full range frequency response and the purist audio reproduction 96 kHz PCM source material can be play back in this mode HDCD source material can be played in this mode OSE version only Notes Internal speaker size is setup to front L R Large Center Large Surround L R Large and Subwoofer yes automatically Tone controls and additional processing are also defeated When you use this mode with certain DVD and CD players performing operations such as Skip or Stop may momentarily interrupt the output 30 CAUTION NOTE for DTS signal Connected DVD player laser disc player or CD player needs to support DTS digital output You may not be able to play some DTS source signals from certain CD players and LD players even if you connect the player to the SR7300 digitally This is because the digital signal has been processed such as the output level sampling frequency or frequency response and the SR7300 cannot recognize the signal as DTS data Depending on the player used DTS play may produce short noise This is not a malfunction While
75. ode and MULTI will light in the display MULTI ROOM Video output will show OSD information to condition of MULTI ROOM setup MULT ROOM ROOM MULT I OFF VIDEO AUDIO DVD DVD VARIABLE 90 dB OFF VOLUME SETUP VOLUME LEVEL SLEEP TIMER MAIN ROOM STATUS VIDEO DVD MAIN AUDIO DVD EXIT 2 Press the VOL A or VOL V button on the multi room remote control unit to set the desired sound volume 3 In multi room mode the multi room remote control unit can be used in the multiroom to operate the following functions General Controlling volume level sleep timer and muting Selecting input audio and video source Tuner Selecting band controlling preset channel up and down tuning up and down direct frequency call Notes for multi room system e The MULTI ROOM OUT is analog outputs This is not support to digital signals input e If Tuner FM or AM is active in main room you can not control any function of tuner In this case you can listen the same condition as main room REMOTE CONTROLLER OPERATION CONTROLLING MARANTZ COMPONENTS 1 Press the desired function button The selected function name and USE are displayed in LCD 2 Press the desired operation buttons to play the selected component For details refer to the components s user guide It may not be possible to operate some models CONTROLLING A MARANTZ DVD PLAYER DVD MODE V OFF EQ 7
76. ommand set of the remote controller itself and therefore does not transmit any signal Further the function buttons may also be programmed to execute macros A macro allows a complex string of operations to be performed in series simply by pressing a single button One button can be programmed to learn sequences containing up to 10 commands The following is an example of such a sequence that can be activated automatically using a macro Turn the receiver ON Switch the function to DVD Set the Surround Mode to VIRTUAL gt Set the DVD player to Play EXIT button when AMP mode is selected Used to exit setup menu TEST button when AMP mode is selected Used to enter the test tone menu MENU OSD button when AMP mode is selected When this button is pressed the current setting are displayed on the TV monitor VOLUME Y buttons Used to adjust the volume on receivers and other components TV equipped with volume control P SCAN preset scan button when TUNER mode is selected Used to start preset scan when SR7300 is selected TUNER mode MUTE button Muting button of the SR7300 Press this button decrease the sound temporarily Press this button again to return to the previous sound I o g Z Lu MEMO button Memory enable button for various preset functions NIGHT button when AMP mode is selected Pressing this button prevents the Dolby Digital signal from playback at a loud voic
77. ommand set of the remote controller and no signal is transmitted to the component CLEARING MACRO PROGRAMS ADJUSTING THE INTERVAL TIME OF MACRO The following procedure is used to erase macros you have OPERATIONS TRANSMITTING T programmed into the remote controller s memory M L SEA eee 1 Press and hold the T MODE and MENU button until the MACRO 1 Press and hold the T MODE and SETUP button until the SETUP 3 is displayed on the LCD is displayed on the LCD D LEARN and MACRO is displayed blinking SETUP is displayed for 3 seconds gt m z AANI ZNN HUC 2 Press and hold the CL button then press the button for the Function to be cleared in this case DVD for 3 seconds DVDCL will appear on LCD a 92 bk 22 fusi e 1 2 Confirm the display changes from SETUP to MCRxx ss le Ges q ENS 7 xx means the interval time of macro operations transmitting ZU ER COE EOS E ME OU 171 gt gt In Ir ile T Press the Cursor lt button to change the interval time J Press the OK button to clear and return step 1 The interval time can be changed from 0 5 to 5 seconds by 0 5 To cancel the memory clearing operation do not press OK seconds step button and simply touch any other button 0 5 seconds M e LEARN MACRO ANSI EI EU EINE I See 1 second 4 return
78. on Press this button to enter the tuner preset memory numbers or station names See page 35 rysRSce H 0 TUNING 4 Down gt Up buttons Press these buttons to change the frequency or the preset number These buttons can change setup parameter to each content in OSD menu system See page 35 F P Frequency Preset button During reception of AM or FM you can change the function of the UP DOWN buttons for scanning frequencies or selecting preset stations by pressing these buttons See page 35 9 MODE button Press this button to select the auto stereo mode or mono mode when the FM band is selected The AUTO indicator lights in the auto stereo mode See page 35 MUTE button Press this button to mute the output to the speakers Press it again to return to the previous volume level 17 VOLUME control knob Adjusts the overall sound level Turning the control clockwise increases the sound level 2 ATT Attenuate button If the selected analog audio input signal is greater than the capable level of internal processing PEAK indicator will light If this happens you should press the ATT button ATT is displayed when this function is activated The signal input level is reduced by about the half Attenuation will not work with the output signal of REC OUT CD R MD VCR1 and VCR2 output This function is memorized for each input function I o 2
79. on there is no signal at the record outputs when the 7 1 Ch Input is in use AUX2 INPUT If you don t need to connect 7 1 Ch input terminals with multi channel decoder L front left and R front right inputs terminals are available as AUX2 input In this case You can connect additional audio source to AUX2 as other audio input terminals SETUP EXIT EH CHANNEL SKIP TUNE SEARCH REC SPKR ATT MULTI AS EX 34 BASIC OPERATION TUNER LISTENING TO THE TUNER Frequency scan step for AM is selectable Default setup is 10 kHz step if your country s standard is 9 kHz step Press TUNER button on the remote more than 6 seconds Scan step will change Note e Preset memory for the tuner will clear by changing this setup AUTO TUNING 3 2 1 CHANNEL SKIP TUNE SEARCH Pri U USING THE SR7300 1 To select tuner and desired band FM or AM press the TUNER button on the front panel 2 F P button on the front panel to display the frequency Press the TUNING lt or gt button on the front panel for more than 1 second to start the Auto tuning function d Automatic searching begins then stops when a station is tuned in Using the remote control unit 1 To select tuner and desired band FM or AM press TUNER button twice within in two seconds on the remote Press 4 or
80. on between 1 and 30 feet in 1 0 foot intervals 0 3 to 9 meters in 0 3 meter intervals SURR B L Set the distance from the surround back left speaker to your normal listening position between 1 and 30 feet in 1 0 foot intervals 0 3 to 9 meters in 0 3 meter intervals SURR B R Set the distance from the surround back right speaker to your normal listening position between 1 and 30 feet in 1 0 foot intervals 0 3 to 9 meters in 0 3 meter intervals Notes e Speakers that you selected None for in the Speaker Size menu will not appear The setting of Surr Back L and Surr Back R appears if set for two surround back speakers in the Speaker Size menu The setting of Surr Back appears if set for one surround back speaker in the Speaker Size menu 2 3 SPEAKERS LEVEL Here you will set the volume for each speaker so that they are all heard by the listener at the same level Note The speaker level settings is not available in 7 1 channel input mode and S Direct mode 2 3 SPEAKERS LEVEL TEST MODE FRONT L CENTER FRONT R SURR R SURR BACK SURR L SUB W MAIN RETURN TEST MODE Selects MANUAL or AUTO for generating mode of test tone Left or Right cursor button If you select AUTO the test tone will be cycled through in a circular pattern which is Left 2 Center Right Surround Right Surround Back Right Surround Back Left Surround Left Subwoofer Left
81. on name preset or to set select a CD track number etc The functions of these buttons are dependent on the function button selected Surround mode buttons when AMP mode is selected Used to select the surround mode 9 CL clear S DIRECT source direct button Used to cancel for certain memory or programming operations when AMP mode is selected Used to select the S DIRECT source direct mode In source direct mode the tone control circuitry is bypassed INPUT button Used to select monitor input Note e This button is unavailable for SR7300 11 T MODE button when TUNER mode is selected Used to select the auto stereo mode or mono mode when the FM band is selected The AUTO indicator lights in the auto stereo mode TV CH A Y buttons Used to increase or decrease the TV channel TOP MENU button when DVD mode is selected Used to call up the top menu of the DVD Tone Deck control buttons Tone control buttons when AMP mode is selected The TREBLE buttons are used to adjust the tone control of high fre quency sound for left and right speaker The BASS buttons are used to adjust the tone control of low frequency sound for left right and subwoofer speaker Deck control buttons when Tape mode is selected The DECK A button are used to select the deck A The DECK B button are used to select the deck B The lt gt button are used to change the direction CURSOR OK button Used to opera
82. one was selected for the Surround right speaker setting in the Speaker size then this setting will not appear SURR BACK LEVEL Set the effect level of the Surround Back speaker between 10 and 10 dB level in 1 dB level interval f None was selected for the Surround back speakers setting in the Speaker size then this setting will not appear SUB W LEVEL Set the effect level of the subwoofer speaker between 15 and 10 dB level in 1 dB level interval If None was selected for the Subwoofer speaker setting in the Speaker size then this setting will not appear If you finish the setup in this item move cursor to MAIN with A or V cursor buttons and press OK button 5 PL II PRO LOGIC II MUSIC PARAMETER Pro Logic mode creates a rich and enveloping surround ambience from stereo sources such as CDs In this mode SR7300 includes three controls to fine tune the soundfield as follow 5 MUSIC PARAMETER PARAMETER DEFAULT PANORAMA DIMENSION CENTER WIDTH Select PRO LOGIC II in SETUP MAIN MENU with A or V cursor button and press the OK button PARAMETER Select DEFAULT or CUSTOM with 4 or gt cursor button If you select CUSTOM you can adjust three parameters as follow PANORAMA Select the Panorama mode On or Off with lt or gt cursor button Panorama wraps the sound of the front left and right speakers around you for an exciting perspective DIMENSION Set
83. onnect the left and right audio channels properly Red connectors are for the R right channel and white connectors are the for L left channel COMPONENT S VIDEO VIDEO IN IN SATELLITE TUNER lt ji AUDIO VIDEO S VIDEO DIGITAL AUDIO IN IN COAXIAL el D DIGITAL AUDIO OPTICAL 8 m o momo TV Be sure to connect input and output of video signal properly e If you connect the S VIDEO or component signal to the S VIDEO or component jack on this unit it is not necessary to connect the conventional video signal to the VIDEO composite jack If you use both video inputs this unit gives priority to the S VIDEO signal Each type of video jack works independently Signals input to the VIDEO composite and S VIDEO jacks or component are output to the corresponding VIDEO composite and S VIDEO or component jacks respectively e This unit has the TV AUTO ON OFF function to turn ON or OFF automatically the power by the incoming video signal from VIDEO jacks You may need to setup the digital audio output format of your DVD player or other digital source component Refer to the instructions of the each component connected to the digital input jacks There is no Dolby Digital RF input jack Please use an external RF demodulator with Dolby Digital decoder to connect a vide
84. ont SPKR Large Center SPKR Large Surround SPKR Large Sub woofer On MULTI Multi Room button Press this button to activate the Multiroom system MULTI indicator will light in the display 920 PHONES jack for stereo headphones This jack may be used to listen to the SR7300 s output through a pair of headphones Be certain that the headphones have a standard 1 4 stereo phone plug Note that the main room speakers will automatically be turned off when the headphone jack is in use Notes When using headphones the surround mode will automatically change to STEREO e The surround mode returns to the previous setting as soon as the plug is removed from the jack 20 INFRARED receiving sensor window This window receives infrared signals for the remote control unit FL DISPLAY 1 DISP Display Off indicator This indicator lights when the SR7300 is in the display off condition 2 SLEEP timer indicator This indicator lights when the seep timer function in main room is in use 3 Multi room system indicator This indicator lights when the multi room system is active 4 AUTO SURR Auto Surround mode indicator This indicator illuminates to show that the AUTO SURROUND mode is in use 5 TUNER s indicators AUTO This indicator illuminates when the tuner s Auto mode is in use TUNED This indicator illuminates when a station is being received with sufficient signal strength to provide a
85. ont speakers Center speaker Surround speakers Surround Back speaker Sub woofer speaker 31 m Z G ay I OTHER FUNCTION TV AUTO ON OFF FUNCTION This function allows the component connected to the TV VIDEO in jack to control the power ON OFF to the SR7300 AUTO POWER ON 1 Be sure TV auto mode is ENABLE Refer page 24 System Setup 2 Connect your TV TUNER etc to the TV VIDEO in terminal Be sure to connect the VIDEO input Turn OFF the power to the TV TUNER and the SR7300 Turn ON the TV TUNER and tune in a receivable station When the station is received the SR7300 turns ON and TV is selected automatically AL e AUTO POWER OFF 1 Inthe above situation turn the TV TUNER OFF or select a channel that does not contain any broadcast 2 The power to the SR7300 switches to STANDBY after approx 5 minutes Notes e AUTO POWER OFF is canceled if the SR7300 is set to a source other than TV The function reactivates when is selected again e Some broadcasts may cause the TV AUTO FUNCTION to turn ON e S Video terminal does not support AUTO ON OFF function ATTENUATION TO ANALOG INPUT SIGNAL SETUP EXIT CHSEL TEST ff EN E Ee lt lt eM E auf art Wan SR Q ooo If the selected analog audio input signal is greater than the capable level of internal processing PEAK indicator will light up on the front display If t
86. ontazhnaya Street 107497 Moscow Russia SAUDI ARABIA Adawlia Univ Electr P O Box 2154 Alkhobar 31952 Saudi Arabia SINGAPORE Wo Kee Hong Distribution PTE Ltd 130 Joo Seng Road 03 02 Olivine Building Singapore 368357 SLOVAKIA Bis Audio s r o Nam SNP 10 96001 Zvolem Slovakia SLOVENIA Bofex Smartinska 152 HALA V 3 61000 Ljubljana Slovenia SOUTH AFRICA Coherent Imports PTY Ltd P O Box 1614 Alberton 1450 South Africa SPAIN Marantz Spain Martinez Villergas 2 Apartado 2065 Madrid 28027 Spain SRI LANKA The listening Room Mezzanine Floor The Landmark 385 Galle Road Colombo 3 Sri Lanka SWEDEN Audio Nord Almedalsvagen 4 Gotenborg 402 23 Sweden SWITZERLAND Sound Company AG Postfach 8010 Zurich Switzerland SYRIA Hamzeh amp Partners Hafez lbrahim Str No 117 Damascus Shalan Syria TAHITI Covecolor Av Prince Hinoi Cours de l union sacr P O Box 2334 Papeete Tahiti TAIWAN Pai Yuing Co Ltd 6th No 148 Sung Kiang Road Taipei 10429 Taiwan R O C THAILAND MRZ Standard Co Ltd 746 750 Mahachai Road Wangburapa Bangkok 10200 Thailand TUNESIA Societe EDEVIG 40 Avenue du Golfe Arabe El Menzah 1004 Tunesia TURKEY Turk Philips Ticaret A S Yukari Dudullu Organize sanayi Bolgesi 2 Cadde no 28 81260 Umraniye Istanbul Turkey U K Marantz U K Ltd Kingsbridge House Padbury Oaks 575 583 Bath Road Longford Middlesex UB7 OEH U K U S A Marantz America Inc 1100 Maplewood Drive Itasca IL 60143 U S A YUGOSL
87. onto the CD while remaining completely compatible with the CD format When listening to HDCD recordings you hear more dynamic range a focused 3 D sound stage and extremely natural vocal and musical timbre With HDCD you get the body depth and emotion of the Original performance not a flat digital imitation 9 HDCD High Definition Compatible Digital and Pacific Microsonics are either registered trademarks or trademarks of Pacific Microsonics Inc in the United States and or other countries HDCD system manufactured under license from Pacific Microsonics Inc This product is covered by one or more of the following In the USA 5 479 168 5 638 074 5 640 161 5 808 574 5 838 274 5 854 600 5 864 311 5 872 531 and in Australia 669114 Other patents pending I o 2 TT m Z G ay I FEATURES The SR7300 incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX Dolby Digital DTS ES Discrete 6 1 and Matrix 6 1 DTS Neo 6 Cinema Music Dolby Pro Logic II Movie and Music Circle Surround II Cinema and Music In addition Marantz has focused on the future By utilizing pre out jacks 7 1 direct inputs and a RS232C communication port the SR7300 is upgradeable to tomorrow s technology today The SR7300 features a fully discrete 6 channel current feedback amplifier section capable of delivering 105 watts of high current amplification for cont
88. osed to rain or water 25 d Ifthe product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e Ifthe product has been dropped or damaged in any way and f When the product exhibits a distinct change in performance this indicates a need for service FIGURE 1 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 GROUND CLAMP T ELECTRIC SERVICE EQUIPMENT T 2 GROUND CLAMPS
89. ources can be played in rooms other than the main room in which this unit and the playback devices are installed SR7300 has some feature to MULTI ROOM SYSTEM as source selector OSD information sleep timer and remote control MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS The SR7300 is equipped with audio pre out terminals for which the volume is adjustable and composite video output terminals as the MULTI ROOM output terminals A separately sold stereo power amplifier 5 6100 be connected to enjoy multi room playback Operation to MULTI ROOM OUT without the remote controller 1 Press the MULTI ROOM button unit enters multi room mode and the display indicates SELCT SOURCE and flashes the MULTI indicator for approx 10 seconds 2 inthis time you can select the input source by pressing the input selector buttons Then the display indicates MULTI VOL VOLUME xx dB for approx 5 seconds 2 During this time you can set the volume level the multi room as desired This will only set the volume in the second room OPERATION TO MULTI ROOM OUTPUTS WITH THE REMOTE CONTROLLER FROM SECOND ROOM SETUP EXIT C IE em 0 CHANNEL SKIP TUNE SEARCH REC SPKR A B ATT MULTI LM Jd _l_ y 1 W EC er 1 Press the MULTI on multi room remote control unit from the MULTI ROOM This operations will put the SR7300 into multi room m
90. puts SACD Multi Channel 7 1 channel direct inputs and a speaker B and OSD output versatility is taken to a stunning new level Furthermore the SR7300 can output the OSD information through the Y C S video and composite video outputs An easy to use programmable learning remote control allows full access to all of the operating functions and can be used for system operation as well The new generation of Marantz Receivers are stylish and completely symmetrical On the front panel of the SR7300 buttons are kept to a minimum Source selectors and volume controls are intuitively placed The large left dial knob on the left can be used as multi dial which allows all functions of the SR7300 to be operated via the front panel The SR7300 is here to perform in your unrivaled home entertainment setup Dolby Digital EX Dolby Digital DTS ES Discrete 6 1 Matrix 6 1 Neo 6 Dolby Pro Logic Il Movie Music Circle Surround II Movie Music Mono 6 x 105 Watts 8 Ohm Discrete Amplifiers High Power Current Feedback Circuitry Massive Energy Power Supply Huge El Transformer Large ELCO s 192 kHz 24 bit Crystal DAC for all 8 Channels 24 bit Digital Surround Processing Chipsets Video Off Mode Large Heavy Duty Banana Type Speaker Terminals for all Channels RS232C Terminal for Future Upgrades or System Control oet Up Menu Via Composite and S Video Output Auto Input Signal Detection Improved Station Name Input Method 50 Preset
91. quency limited in earlier Pro Logic type systems Bass effects are an important part of home theater For optimal enjoyment a subwoofer should be used as it is optimized for low frequency reproduction If you have full range front speakers however they may be used in place of a subwoofer with proper setting of the switches in the menu system Surround Back 777 Left Surround Back _ Front Center SEN Front Right Surround Back Surround Right Right Front left and right speakers We recommend to set the front L and R speakers with 45 60 degrees from the listening position Center speaker Align the front line of the center speaker with the front L R speakers Or place the center speaker a little backward from the line Surround left and right speakers Place the speakers right beside of the listening position or a little forward Surround back speaker Place the speaker behind of the listening position Surround back left and right speaker Place the speaker behind of the listening position Subwoofer We recommend to use a Sub woofer to have maximum bass effect Sub woofer bears only low frequency range so you can place it anywhere in the room 14 HEIGHT OF THE SPEAKER UNITS Front left and right speakers and a center speaker Align the tweeters and mid range drivers on the three front speakers on the same height as well as possible Surround left and right speakers and surround back speaker Place
92. r may be switched off with its own power switch Caution n order to avoid potential turn off thumps anything plugged in here should be powered up before the SR7300 is turned on The capacity of this AC outlet is 120W Do not connect devices that consume electricity more than the capacity to this AC outlet If total power consumption of connected devices exceeds the capacity protection circuit shuts down the power supply 9 Speaker outputs terminals for Main room Six terminals are provided for the front left front right front center surround left surround right and surround back speakers Subwoofer Output Connect this jack to the line level input of a powered subwoofer If an external subwoofer amplifier is used connect this jack to the subwoofer amplifier input If you are using two subwoofers either powered or with a 2 channel subwoofer amplifier connect a Y connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier 11 7 1 CHANNEL or AUX2 INPUT By connecting a DVD Audio player SACD multi channel player or other component that has a multi channel port you can playback the audio with 5 1 channel or 7 1 channel output Multiroom Outputs Audio L amp R Video These are the audio and video output jacks for the Multi zone Multi room Connect these jacks to the optional audio power amplifiers or video display devices to listen and view to the source selected by the
93. ral soundstage from two channel source material This is done by feeding the left channel signal to both left front and left surround speaker and the right channel signal to both right front and right surround speaker Additionally the center channel reproduces a mix of the right and left channel I o 2 TT 29 m Z G 70 I CIRCLE SURROUND CSII CINEMA CSII MUSIC CSII MONO Circle Surround is designed to enable multi channel surround sound playback of non encoded and multi channel encoded material Backward compatibility provides listeners with up to 6 1 channels of surround performance from entire collection of music and film including broadcast videotape and stereo recorded music Regarding to source material you can select CSII Cinema mode CSII Music mode or CSII Mono mode Note CS II mode is available to 2ch input signal which is encoded Dolby Digital or PCM format e PCM audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz 44 1 kHz or 48 kHz VIRTUAL This mode creates a virtualized surround sound experience from a two speaker front L and R playback system playing any multi channel audio source such as found on DVDs and digital broadcasts including Dolby Digital Dolby Pro Logic or DTS STEREO This mode bypasses all surround processing otereo program sources the left and right channels play normally when PCM audio or analog stere
94. recording of all channels including the surround back channel s and higher quality of audio reproduction DTS ES is not available in the system without surround back speaker dts dis Neo 6 Cinema Neo 6 Music This mode is for DTS encoded source materials such as LASER DISC CD and DVD Neo 6 is to some 2 channel signal source dts This mode is enabled when playing source materials encoded in dts multi channel Playing multi channel encoded 5 1 channel dts sources provides five main audio channels left center right surround left and surround right and Low Frequency Effect channel dts ES decoding is not available in this mode The DTS mode cannot use when an analog input has been selected Neo 6 Cinema Neo 6 Music This mode decodes 2 channel signals into 6 channel signals using high accuracy digital matrix technology The DTS NEO 6 decoder has near discrete properties in the frequency characteristics of the channels as well as in channel separation According to the signals to be played back DTS NEO 6 uses either the NEO 6 CINEMA mode optimized for movie playback or the NEO 6 MUSIC mode optimized for music playback Note Neo 6 mode is available to 2ch input signal which is encoded Dolby Digital or PCM format PCM audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz 44 1 kHz or 48 kHz MULTI CH ST This mode is used to create a wider deeper and more natu
95. rently selected functions and modes is displayed on the LCD e LEARN USE MACRO NA NA NA NA NA ENN ZN ZN LN amp Function Name indicator Displays the name of the currently selected function DVD TV etc using up to 5 characters LEARN indicator Indicates when the remote controller is in the LEARN mode USE indicator For normal operation the USE indicator is displayed d MACRO indicator Indicates when the remote controller is in the MACRO mode Transmission indicator Indicates when the remote controller is transmitting a signal D Low battery indicator When this indicator appears the batteries should be replace REMOTE CONTROL RANGE The distance between the transmitter of the remote control unit and the IR SENSOR of the SR7300 should be less than about 5 meters If the transmitter is pointed to a direction other than the IR SENSOR or if there is an obstacle between them remote control may not be possible Remote controllable range Remote control unit RC7300SR LOADING BATTERIES The life of the batteries used with the remote control unit is about 4 months with normal use Also be sure to replace batteries earlier when you notice that they are getting weak 1 Remove the back cover 2 Insert the new batteries AA type with correct and polarity Note The supplied batteries are shipped to confirm the initial operation Therefore the
96. rval with lt or gt cursor button This can be popped out of the surround audio effects allowing the listener to easily discern what the actors Say If NONE was selected for the Center speaker setting in the Speaker size then this setting will not appear If you finish the setup in this menu move cursor to MAIN with A or V cursor buttons and press OK button 7 MULTI ROOM SR7300 has some feature to MULTI ROOM SYSTEM as source selector OSD information sleep timer Multi Room Speaker output and remote control You can set such feature by this sub menu 7 MULTI ROOM MULTI ROOM OFF VIDEO AUDIO DVD DVD VARIABLE 90 dB OFF VOLUME SETUP VOLUME LEVEL SLEEP TIMER MAIN ROOM STATUS VIDEO DVD MAIN AUDIO DVD EXIT 1 Select MULTI ROOM in SETUP MAIN MENU with A or Y cursor button and press the OK button 2 To Select desired contents as bellow press A or V cursor button MULTI ROOM To switch on the Multi room output ON or OFF press 4 or gt cursor button VIDEO Select the video source of the Multi room output with lt or gt cursor button AUDIO Select the audio source of the Multi room output with lt or gt cursor button VOLUME SETUP Select whether the Multi room output level is variable or fixed with a lt or gt cursor button VOLUME LEVEL Adjust the Multi room output level with 4 or gt cursor button SLEEP TIMER SLEEP timer function is available during the multiroom is ac
97. s If you finish these setup move cursor to NEXT with Up or Down cursor button and then press OK button to go to next page SUBWOOFER YES Select when a subwoofer is connected NONE Select when a subwoofer is not connected FRONT L R LARGE Select if the front speakers are large sized SMALL Select if the front speakers are small sized e If NONE is selected for the Subwoofer setting then this setting is fixed to Large CENTER NONE Select if no center speaker is connected LARGE Select if the center speaker is large sized SMALL Select if the center speaker is small sized SURROUND L R NONE Select if no surround left and right speakers are connected LARGE Select if the surround left and right speakers are large sized SMALL Select if the surround left and right speakers are small sized SURR BACK NONE Select if no surround back left and right speakers are connected 2CH Preout only Select if surround back left and right speakers are connected 1CH Select if the one surround back speaker connected If None is selected for the Surround L R setting then this setting is fixed to None f you are able to position two Surround Back speakers in your listening environment two Surround Back speakers can be used In this case connect a 2 channel power amplifier to the PRE OUT SBL and SBR terminals on the SR7300 and connect the surround back left amp right speakers to thi
98. s Auto Adjust Function for Speaker Distance Settings Delay Time Front Optical AUX Input Digital Camera Portable DVD Large Multi Operation Left Dial Knob 2 Assignable DC Trigger Outputs Programmable learning remote control Built in HDCD decoder OSE version only ACCESSORIES Remote Controller RC7300SR gt lt gt AA size batteries X 2 AM Loop Antenna FM Antenna Registration Card User Guide FRONT PANEL 1 POWER switch and STANDBY indicator When this switch is pressed once the unit turns ON and display appears on the display panel When pressed again the unit turns OFF and the STANDBY indicator lights When the STANDBY indicator is turned on the unit is NOT disconnected from the AC power 2 SELECT MULTI FUNCTION MODE SELECT button Press this button to change the mode for MULTI FUNCTION control dial SURROUND MODE Selector amp MULTI FUNCTION control dial This dial changes surround mode sequentially or select contents of OSD menu system 4 ENTER MULTI FUNCTION ENTER button Press this button to enter the setup by MULTI FUNCTION dial 5 CLEAR button Press this button to cancel the station memory setting mode or preset scan tuning See page 35 6 MEMORY butt
99. s power amplifier see page 15 You will also need to make the appropriate setting SURR BACK 2CH SURR BACK SIZE LARGE Select if the surround back speakers are large sized SMALL Select if the surround back speakers are small sized If None is selected for the Surround L R setting then this setting is not available LPF HPF When you use a subwoofer you can select the cutoff frequency for the small speakers used Select one of the crossover frequency levels according to the size of the small speaker connected 80Hz Select this when the cone speaker unit built in the speaker system is about 12 cm 4 3 4 inches 100Hz Select this when the cone speaker unit built in the speaker system is about 10 cm 3 15 16 inches 120Hz Select this when the cone speaker unit built in the speaker system is about 8 cm 3 3 16 inches Notes Use the above comments as reference when adjusting If S Direct mode 7 1CH Input is in use this function does not take effect BASS MIX The bass mix setting is only valid when LARGE is set for the front speakers and YES is set for the subwoofer at stereo playback e When the BOTH is selected the low frequency signal range of LARGE are produced simultaneously from those channels and the subwoofer channel In this playback mode the low frequency range expand more uniformly through the room but depending on the size and shape of the room interferen
100. sed Disconnecting power plug for long periods of time will erase preset when the PRESET button is data If that happens input the preset data again pressed Control with the remote control unit Batteries are consumed Replace all the batteries with new ones Remote controller s function key setting is wrong Select different position from which equipment will be controlled The distance between this SR7300 and the remote Move closer to this SR7300 commander is too far Something is blocking SR7300 and the remote Remove offending object commander GENERAL MALFUNCTION If the equipment malfunctions this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits Therefore disconnect the plug from the AC line supply after waiting at least three minutes reconnect the plug to the AC line supply re attempt to operate the equipment Memory backup n case a power outage occurs or the power cord is accidentally unplugged the SR7300 is equipped with a backup function to prevent memory data such as the preset memory from being erased HOW TO RESET THE UNIT Should the operation or display seem to be abnormal reset the unit with the following procedure The SR7300 is turned on press and hold the SELECT and ATT buttons simultaneously for 3 seconds or more Remember that the procedure
101. t for a few seconds RECALLING A PRESET STATION Using the SR7300 Press the F P button to show the preset station on the display 2 Selectthe desired preset station by pressing the TUNING button on the front panel Using the remote control unit Press the button to select the desired preset station or input your desired preset channel with numeric buttons on the remote 36 PRESET SCAN KEE SCH SE we STEREO VIRTUAL _ PTY 7 8 9 9 EEN NIGHT MEMO 3 f El WW C CHANNEL SKIP TUNE SEARCH INPUT T MODE P SCAN MUTE OO 3 S c Pee a aa 65 0 50 Using the remote control unit 1 Press the P SCAN on remote PRESET SCAN appears on the display and then the preset station with the lowest preset number is recalled first 2 Preset stations are recalled in sequence No 1 No 2 etc for 5 seconds each No stored preset number will be skipped 3 You can fast forward the preset stations by pressing the continuously When the desired preset station is received cancel the preset scan operation by pressing the CL button or P SCAN on the remote CLEARING STORED PRESET STATIONS You can remove preset stations from memory using the following procedure 2 3 1 Recall the preset n
102. t video input used remains routed to the Monitor Outputs This permits simultaneous viewing with video sources CMO a oa OFF V OFF V61IN SEP Re We AUDIO ANGLE UBTITLE 2 SS aS TS DISP RDS EX ES csi M CHST F DIR SEAR INPUT T MODE P SCAN MUTE E EE 1 Select a desired Video source to decide the routed video signal to the Monitor Outputs 2 Press the 7 1 CH INPUT button on the front panel or press 7 1 6 1 IN on the remote to switch the 7 1 channel input 3 necessary to adjust the output level of each channel use 7 1 Ch INPUT LEVEL in OSD menu system as desired Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position For the front left front right center surround left surround right surround back left and surround back right speakers the output levels can be adjusted between 10 to 10 The subwoofer can be adjusted between 15 and 10 dB These adjusting result will be stored to 7 1 Ch INPUT condition see to page 26 4 Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the remote To cancel the 7 1 Ch INPUT setting press the 7 1 CH IN button on the front panel or press 7 1 6 1 IN on the remote Notes When the 7 1 Ch Input is in use you may not select a surround mode as the external decoder determines processing n additi
103. te on screen and other displays used by receivers and other components CH SEL channel select button when AMP mode is selected Used to call SETUP MAIN MENU and adjust speaker levels or 7 1 ch input level SETUP button when AMP mode is selected Used to call up the SETUP MAIN MENU of the SR7300 CONTROL buttons These buttons are used when operating the CD player TAPE deck etc The function of these buttons are dependent on the function button selected when AMP mode is selected ATT button When the input signal is too high and the voice distorts even by throt tling the SR7300 VOLUME control turn on this function ATT is indi cated when this function is activated The input level is reduced Attenuator is invalid for use with the output signal of REC OUT Note This function is unavailable during the digital input is selected SPKR A B button Speaker mode is switched in the following sequence A B 5 A B off MULTI button This button is used to switch the unit to multi room mode Input selector buttons FUNCTION SE LECTOR buttons AUDIO VIDEO INPUT Used to switch the remote controller to the command sets for specific sources amplifier receiver etc thereby allowing a single remote controller to control up to 11 different components To use these buttons to switch the amplifier s source press the desired button twice within 2 seconds The AMP button is used only to switch c
104. ter entry ready status When the SELECT knob is turned or press gt button on the remote alphabetic and numeric characters will be displayed in the following order A 5B C 25123 05 Blank 5 A UP gt lt DOWN 5 After selecting the first character to be entered press the MEMORY or ENTER buttons press MEMO button on the remote The entry in this column is fixed and the next column starts to flash Fill the next column same as To move back and forth between the characters press the TUNING 4 gt button or press lt or buttons on the remote Note Unused columns should be filled by entering blanks To save name press the MEMORY or ENTER button press MEMO button on the remote for more than 2 seconds N I o 2 TT 37 m Z G T I 38 MULTI ROOM SYSTEM The Multi Room system is a function which allows you to listen to the same or a different source in a room other than the room in which the SR7300 is located To use this function a multi room remote unit and remote control signal receiver available from your Marantz dealer are necessary The operations possible with the multi room function are explained briefly below For details refer to the instruction manual supplied with the multi room remote control unit and receiver When the outputs of the MULTI ROOM OUT terminals are wired and connected to amplifiers installed in other rooms different s
105. the Dimension level between 0 and 6 level in 1 level interval with lt or gt cursor button Adjust the soundfield either towards the front or towards the rear This can be useful to help achieve a more suitable balance from all the speakers with certain recordings CENTER WIDTH Set the Center width level between 0 and 7 level in 1 level interval with lt or gt cursor button Center Width allows you to gradually spread the center channel sound into the front left and right speakers At its widest setting all the sound from the center is mixed into the left and right This control may help achieve a more spacious sound or a better blend of the front image If None was selected for the Center speaker setting in the Speaker size then this setting will not appear If you finish the setup in this menu move cursor to MAIN with A or V cursor buttons and press OK button 6 CS II CIRCLE SURROUND PARAMETER 6 CS PARAMETER TRUBASS SRS DIALOG 1 Select CS I SETUP MAIN MENU with A or Y cursor button and press the OK button Select desired contents as below press A or V cursor button TRUBASS Set the TRUBASS level between 0 and 6 level in 1 level interval with lt or gt cursor button TRUBASS produced by the speakers to be an octave below the actual physical capabilities of the speakers adding exciting deeper bass effects SRS DIALOG Set the SRS DIALOG level between 0 and 6 level in 1 level inte
106. the home Greater bit depths provide extended dynamic range Higher sampling rates allow wider frequency response and the use of anti alias and reconstruction filters with more favorable aural characteristics DTS 96 24 allows for 5 1channel sound tracks to be encoded at a rate of 96kHz 24bits on DVD Video titles When DVD video appeared it became possible to deliver 24 bit 96 kHz audio into the home but only in two channels and with serious limitations on picture This capability has had little use DVD audio allows 96 24 in six channels but a new player is needed and only analog outputs are provided necessitating the use of the D A converters and analog electronics provided in the player d 96 24 offers the following 1 Sound quality transparent to the original 96 24 master 2 Full backward compatibility with all existing decoders Existing decoders will output a 48 kHz signal 3 No new player required DTS 96 24 can be carried on DVD video or in the video zone of DVD audio accessible to all DVD players 4 96 24 5 1 channel sound with full quality full motion video for music programs and motion picture soundtracks on DVD video DIC bacs DIGITAL EX Dolby Digital identifies the use of Dolby Digital AC 3 audio coding for such consumer formats as DVD and DTV As with film sound Dolby Digital can provide up to five full range channels for left center and right screen channels independent left and right surround c
107. the surround left right and surround back speakers higher to your ears 2 Ft 3 Ft 70cm 1m Also place the speakers on the same height Note Use magnetically shielded speakers for front left right and the center speakers when the speakers are installed near the TV and the TV is a monitor type CONNECTING SPEAKERS PASSIVE POWER FRONT SURROUND SUBWOOFER 777122225 RIGHT LEFT RIGHT LEFT I o 2 TT CS POWERED SUBWOOFER SURROUND CENTER SURROUND LEFT BAGR 14 P 29 ya STEREO POWER AMPLIFIER CONNECTING SPEAKER WIRE Caution 1 Strip away approx 3 8 inch 10 mm of wire insulation Be sure to use speakers with the specified impedance shown on 2 Twist the bared wire ends tight to prevent short circuits the rear panel of this unit 3 Loosen the knob by turning counterclockwise prevent damage to circuitry do d Insert the bare part of the wire into the hole in the side of each not let the bare speaker wires touch each other and do not let them touch any metal part of this unit Tighten the knob by turning clockwise to secure the wire e Do not touch the spea
108. tive set the time with lt or gt cursor button MAIN ROOM STATUS Selected input source in the main room will be displayed Notes e If VOLUME is set to FIXED the multi room output level cannot be adjusted from the second zone If you finish the setup in this menu move cursor to MAIN with A or V cursor buttons and press OK button I o 2 TT 25 8 7 1 CH INPUT LEVEL This sub menu is to adjust the speaker levels for 7 1 channel input sources Here you will adjust the volume for each channel so that they are all heard by the listener at the same level m Z G E ay I 8 7 1 CH INPUT LEVEL FRONT L CENTER FRONT R SURR R SURR B R SURR B L SURR L SUB W MAIN Select 7 1CH IN in MAIN SETUP MENU with A or V cursor button and press the OK button To Select desired channel press A or V cursor button Using the lt or gt cursor buttons adjust the volume level of each channel If you finish the setup in this menu move cursor to MAIN with A or V cursor buttons and press OK button Note e The condition of these setup will be memorized to 7 1 CH INPUT source OO OO OO OH A Gel kl A 9 DC TRIGGER SETUP SR7300 has two DC trigger control jacks each one is selectable to link with input functions for the main room or multi room 1 Select DC TRIG SETUP in SETUP MAIN MENU with A or Y cursor button and press the OK button 9 1 DC TRIGGER SETUP DC T
109. to 2ch input signal which is encoded Dolby Digital or PCM format PCM audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz 44 1 kHz or 48 kHz EX ES This mode provides 6 1 channel surround for DOLBY DIGITAL EX DTS ES encoded source material such as DVD This mode cannot be used when an analog input has been selected Dolby Digital EX In a movie theater film soundtracks that have been encoded with Dolby Digital surround EX technology are able to reproduce an extra channel which has been added during the mixing of the program This channel called Surround Back places sounds behind the listener in addition to the currently available front left front center front right surround right surround left and subwoofer channels This additional channel provides the opportunity for more detailed imaging behind the listener and brings more depth spacious ambience and sound localization than ever before Dolby Digital EX is not available in the system without surround back speaker s DTS ES Discrete 6 1 Matrix 6 1 DTS ES adds the surround center channel audio to the DTS 5 1 channel format to improve the acoustic positioning and makes acoustic image movement more natural with the 6 1 channel reproduction This receiver incorporates a DTS ES decoder which can handle DTS ES Discrete encoded and DTS ES Matrix encoded program sources from DVD etc DTS ES Discrete 6 1 features digital discrete
110. transmitted from the remote controller is received by the remote sensor on this unit then the signal is sent to the connected device through this terminal Therefore you need to aim the remote signal only to the unit Also if a Marantz power amplifier some models excluded is connected with this terminal the power amplifier s power switch is synchronized with this unit s power switch Set the REMOTE CONTROL SWITCH on the units other than this unit to EXT EXTERNAL for this feature REMOTE CD PLAYER CONTROL Lo IN 2 290506 ouT EXTERNAL INTERNAL C CONNECTING THE ANTENNA TERMINALS EM FM EXTERNAL ANTENNA AM EXTERNAL ANTENNA AM LOOP ANTENNA ANTENNA I o 2 TT ASSEMBLING THE AM LOOP ANTENNA 1 Release the vinyl tie and take out the connection line Bend in the reverse direction Inserting into the hole to attach the loop antenna to the antenna stand With the antenna on top any stable surface ON CONNECTING THE SUPPLIED ANTENNAS Connecting the supplied FM feeder antenna The supplied FM feeder antenna is for indoor use only During use extend the antenna and move it in various directions until the clearest signal is received Fix it with push pins or similar implements in the position that will cause the least amount of distortion If you experience poor reception quality an outdoor antenna may improve the quality Connecting t
111. two surround back speakers in the Speaker Size menu e The setting of Surr Back appears if set for one surround back speaker in the Speaker Size menu To adjust the speaker levels for 7 1 channel input sources you will need to use the 7 1 CH INPUT sub menu See page 26 3 PREFERENCE 3 PREFERENCE STANDBY MODE TV AUTO OSD INFO ECONOMY DISABLE ENABLE 1 Select PREFERENCE in SETUP MAIN MENU with A or Y cursor button and press the OK button 2 To select a desired content press A or V cursor button STANDBY MODE When this function is set to ECONOMY you can reduce the power consumption to standby condition Note TV AUTO MULTI RC control and RC232C are disable in ECONOMY setting TV AUTO Select the TV AUTO ON OFF function to enable or disable with lt or gt cursor button refer to page 32 OSD Info Select the OSD information function to enable or disable with lt gt cursor button If you select ENABLE SR7300 will display the status of the feature Volume up down input select etc on the TV monitor But if you do not desire this information select DISABLE If you finish the setup in this item move cursor to MAIN with A or V cursor buttons and press OK button 4 SURROUND 4 SURROUND SURR MODE AUTO HT EQ LFE LEVEL CENTER SURR L SURR R SURR BACK SUB W MAIN 1 Select SURROUND in SETUP MAIN MENU with A or V cursor button and press the OK button 2
112. umber to be cleared with the method described in Recalling a preset station 2 Press the MEMORY button on the front panel or press MEMO button on the remote J Stored preset number blinks in the display for 5 seconds While blinking press the CLEAR button on the front panel or press CL button on the remote d xx CLEAR appears on the display to indicate that the specified preset number has been cleared Notes To clear stored all preset stations press and hold the CLEAR and the F P buttons for two seconds SORTING PRESET STATIONS Stored preset stations number can be kept line To sort the numbers press and hold the MEMORY and the buttons PRESET SORT will appear on the display and sorting will be done INPUT OF THE PRESET STATION This function allows the name of each preset channel to be entered using alphanumeric characters Before name inputting need to store preset stations with the preset memory operation 4 5 6 4 2 5 6 5 SETUP EXIT CL 0 10 INPUT T MODE P SCAN GE Recall the preset number to be inputted name with the method described in Recalling a preset station Press the MEMORY button on the front panel or press MEMO button on the remote for more than 3 seconds The left most column of the station name indicator flashes indicating the charac
113. unction with an external controller to control the operation of the SR7300 by using an external device The RS232C port may also be used in the future to update the operating software of the SR7300 so that it will be able to support new digital audio formats and the like as they are introduced MONITOR OUT This is a monitor output and each one includes both composite video and S video configurations When connecting two video monitors or televisions be aware that the OSD interface can be used with both MONITOR OUT 6 Preamp Outputs L R SL SR SBL SBR C Jacks for L front left R front right C Center SL surround left SR Surround right SBL Surround back left and SBR surround back right Use these jacks for connection to some external power amplifiers Power cable Connect to AC power outlet SR7300 can be powered by 120 V AC only Caution n order to avoid potential turn off thumps anything plugged in here should be powered up BEFORE the SR7300 is turned on AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets SWITCHED and UNSWITCHED outlets are provided The one marked SWITCHED provides power only when the SR7300 is turned on and is useful for components which you use every time you play your system The one marked UNSWITCHED is always live as long as the SR7300 is plugged into a live outlet A component connected here may be left on permanently o
114. ut The digital outputs can be connected to MD recorders CD recorders DAT decks or other similar components I o 2 Lu m Z G E 70 I REMOTE CONTROLLER RC7300SR NAMES AND FUNCTIONS LEARN USE MACRO LOC lt gt lt gt eem weess Gr C be Eise 1 4 LEARNING REMOTE CONTROLLER RC7300SR 1 Infrared window Outputs and inputs an infrared control signals LCD Liquid Crystal Display Used to display information about currently selected functions open close button Used to open or close the door Note e This button is unavailable for SR7300 4 Source POWER ON OFF button Used to turn specific sources Such as DVD players etc ON and OFF independently from the rest of the system 10 EQ button Used to turn on or off HT Home Theater EQ mode This mode compensates for the audio portion of a movie sounding bright When this button is pressed indicator lights up 6 V OFF video off button Used to turn off the video signal DVD operating buttons when DVD mode is selected AUDIO button Used to select one of the audio language ANGLE button Used to change the different camera angle SUBTITLE button Used to select one of the subtitle language Numeric buttons 1 to 9 0 Surround mode buttons Numeric buttons Used to enter figures in the selection of a tuner preset station and sta ti
115. utton e A CLR and LEARN are blinking AUDIO ANGLE DIS DISP RDS S DIRECT SURR MODE NIGHT MUTE DECK A C3 Ca CH BASS TREBLE VOL HC ri DECKB EI J Press OK button to continue erasing A CLR is displayed for 3 seconds and the mode returns to LEARN mode To cancel the erasing operation do not press OK button and simply touch any other button B 4 O T MENU IN INI LESE ANI 4 To return the USE mode press and hold down the OK button until USE is displayed in the display Note Erasing codes will return to the factory preset code or there will leave empty if the button has no factory preset code 42 MACRO MODE PROGRAMMING MACROS Macros make it possible to use a single function button to perform more complex series of operations that would normally require pressing several buttons A single button can be programmed to perform up to 10 steps in sequence A typical example of such a series might be as follows e Turn the main amplifier power ON Switch the function to DVD gt Set the Surround Mode to Virtual Set the DVD player to PLAY No signals may be transmitted during macro programming The various steps that make up a macro are set initially to be sent one after another in 1 second intervals however these intervals may be shortened to as little as 0 5 seconds or lengthened to as much as 5 seconds using the Setup mode n the
Download Pdf Manuals
Related Search
Related Contents
Miele DA 216-2 EXT User's Manual Castro Digital - Manual projetor Vivitek D554 HOME INSECT - KellySolutions.com GWT-200 MANUAL INDEX Copyright © All rights reserved.
Failed to retrieve file