M&S Systems MC602 User's Manual
Contents
1. communications can easily be heard but not so high that the speakers feedback or squeal when communications are attempted 17 MASTER SPEAKER VOLUME CONTROL Recommended setting Maximum This CONTROL is used to control the volume of the MASTER SPEAKER Turning the MASTER SPEAKER VOLUME CONTROL clockwise increases the MASTER SPEAKER volume and turning it counter clockwise decreases the MASTER SPEAKER volume The MASTER SPEAKER VOLUME CONTROL should be normally be set to maximum fully clockwise and the VOLUME UP and DOWN buttons should be used to adjust for the proper listening volume If however another room needs more volume than the MASTER SPEAKER the MASTER SPEAKER VOLUME CONTROL may have to be turned down somewhat and then the music volume increased with the VOLUME UP button to get the perfect volume in each room 18 INTERCOM SELECTOR SWITCHES These switches are used to control the operation of the Room Speaker in each corresponding room The MASTER SPEAKER Switch controls the MASTER SPEAKER The ROOM SPEAKERS Switches 1 through 9 control the corresponding Room Speakers The PATIO SPEAKER Switch controls the Patio Speaker s There are four positions for each of these switches INTERCOM A speaker with its switch set in the INTERCOM position will hear all intercom communications including the chime if used but will not hear the audio sources FM AM AUX and TAPE RADIO INT A speaker with its switch set in the RADIO2. THE SELLER S PART THIS LIMITED WARRANTY DOES NOT COVER DAMAGE CAUSED BY IMPROPER INSTALLATION THE VIOLATION OF APPLICABLE BUILDING OR ELECTRICAL CODES OR THE USE OF NON M amp S NON AIRVAC WIRE CABLE OR WALL HOUSINGS THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS INSTALLED IN A PRIVATE RESIDENCE UNDER NO CIRCUMSTANCES SHALL THE SELLER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE OR INABILITY TO USE THIS PRODUCT IN NO EVENT SHALL SELLER S LIABILITY FOR BREACH OF WARRANTY BREACH OF CONTRACT NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT Some states do not allow the exclusion or limitation of consequential incidental or special damages so the above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state 20 IMPORTANT All M amp S Wire and Cable Products are U L Approved MLS SYSTE a Printed in U S A 21 Lit No 115758 Rev C
3. The MC602 was designed to be as user friendly as possible It also indicates when and how the intercom function is being used The MC602 has an optional Door Release which can be used to open a door or gate from the Master or any room with remote scan speakers The MC602 provides a Security interface which allows any remote scan speaker to be used as a panic alarm for the security system or the MC602 can provide a Home Automation interface which allows any remote scan speaker to control a group of lights and or appliances These same remote scan speakers allow memory or station tuning changing sources music ON OFF control and system wide music volume control Up to four optional hand held remote controls can be used to control the MC602 from any room inside and even outside your house The MC602 allows you to monitor any room including the Master to let you know when a baby is crying or when an elderly person needs help The MC602 can be set up so that this monitored room does or does not hear other communication in the house There is also an intercom only position a music with intercom override position and an off position for each room In addition your new musical intercom also features Smart Chime which will not interfere with Door Communications Lightning static and surge protection Improved reliability and serviceability Your MC602 is designed to make your home more functional and enjoyable Prepare yourself for a more sat
4. the ROOM LISTEN and ROOM TALK buttons when you are finished talking the MC602 will automatically listen you will hear what is being said to the person at the door s for approximately 25 seconds You may talk to the person at the door again anytime by holding in the ROOM LISTEN and ROOM TALK buttons Each time the buttons are released the door speaker s can be listened to for another 25 seconds If you are done communicating with the person at the door and or you do not want to listen to the door speaker the 25 second listening time can be canceled by momentarily pressing either the ROOM LISTEN or the ROOM TALK button by itself NOTE When communicating with the person at the door s both sides of the conversation will be heard at each speaker including the master that is in the RAD INT or INT position See section 18 22 ROOM SPEAKER VOLUME CONTROL Recommended setting Maximum This CONTROL is used to control the volume of the ROOM SPEAKER Turning the ROOM SPEAKER VOLUME CONTROL clockwise increases the ROOM SPEAKER volume and turning it counter clockwise decreases the ROOM SPEAKER volume The ROOM SPEAKER VOLUME CONTROL should normally be set to maximum fully clockwise and the VOLUME UP and DOWN buttons See section 10 amp 11 should be used to adjust for the proper listening volume NOTE The ROOM SPEAKER VOLUME CONTROL can be used to prevent others from monitoring the room that you are in by turning the VOLUME CONTROL fully coun
5. to Room communication throughout your house as well as furnishing AM FM or auxiliary source audio An optional door chime can be integrated into the system to provide door communication with automatic music muting The MC602 contains a Digital Clock with a back up power supply that never needs replacing It maintains the correct time and presets for up to 2 hours during a power outage The Hands Free communications allows every station in the house to initiate a call and then to listen for the response The call initiator does have to press TALK and LISTEN but the person responding does not need to press any buttons The door is even easier to answer with Automatic Hands Free communications from any station The system automatically listens to the door after you talk to it The state of the art transreflective LCD display and power conserving backlight can be read in any lighting condition from direct sunlight to complete darkness The unit provides excellent fidelity for up to 15 rooms with plenty of power The MC602 has a Digital Phase Lock Loop Tuner with 8 AM and 8 FM Station Presets The MC602 also has two external source inputs AUX IN and TAPE IN and one line output TAPE OUT that can be used with M amp S s built in Cassette Tape and or CD player as well as your TV or other music sources The MC602 has the ability to turn itself ON and OFF at preset times like an alarm clock or for security to play music in the house while you are gone
6. 602 TROUBLESHOOTING TIPS Problem What to Check No FM or 1 Power turned on Section 3 AM reception 2 Proper Source selected Section 6 3 Speaker Switches set correctly Section 18 Display Flashing Extended loss of electrical power Set clock and auto Section 5 Program radio frequencies Section 9 Program REMOTE CONTROL TRANSMITTER s Feedback or Squeal Intercom Volume CONTROL adjusted properly Section 16 Weak or no Intercom 1 Intercom Volume CONTROL adjusted properly Section 16 2 Speaker Switches set correctly Section 18 3 Room Speaker Volume CONTROL adjusted properly Section 22 Display Flashing Reset Not complete from power loss Strange Characters Remove the face panel and touch the four silver solder dots next to the word RESET to the right of the twelve buttons This should insure a proper reset of the MC602 the display should blink 12 00 Set clock and auto Section 5 Program radio frequencies Section 9 Program REMOTE CONTROL TRANSMITTER s 19 STATEMENTS OF WARRANTY M amp S SYSTEMS Limited 2 Year No Fault Product Warranty M amp S SYSTEMS warrants for 2 years all products to be free of defects M amp S SYSTEMS honors the 10 Year No Fault warranty for AirVac Gold power units See section below The warranty period begins from either 1 the date of first user purchase of this product or 2 the first close of escrow date on a residence in which this new product was or
7. INT position will hear the audio sources FM AM AUX and TAPE as well as all intercom communications including the chime if used OFF A speaker with its switch set in the OFF position will not hear anything Note If one of the indoor rooms master 9 are turned off that speaker can still be used to talk to other rooms or listen to other rooms when its talk and listen buttons are pressed However when the patio is turned off it is disconnected from the master and can not be used to talk from listen to or anything else MONITOR A speaker with its switch set in the MONITOR position will not hear anything but the speaker will be used as a microphone Any sounds that this microphone picks up will be added to the selected source and heard from any speaker that is in the RADIO INT position The MONITOR position can be used to listen to monitor a baby s or elderly person s room NOTE The sounds from the MONITORED room will be added to the selected source means that if you are listening to the FM radio in the Living room and the baby starts crying in the MONITORED baby s room the baby s crying will be combined with the FM radio and you will hear both at the same time To listen only to the MONITORED room simply turn the MC602 off with the POWER button The MC602 is normally configured so that intercom communications including the door chime will not be heard from the speaker being monitored However as we understand that e
8. M amp S SYSTEMS Model MC602 Master Unit Owner s Guide uP TUNING VOLUME DOWN SOURCE TIME SET AUTO amp POWER DOWN m s fine h ome OMS acoustics This booklet contains the information you need to get the most from your musical intercom system It also tells you what to do if your system develops operating problems and contains applicable statements of warranty Keep this booklet for future reference CONTENTS MG602 Featuresyinits cage ti erst ath a ate et he ee 1 MC602 Master Unit Operation 0 0 cece ett 2 S tting TIME seis cece oho inbred ae ener aera A eee Pa 4 SECK SCAN meena diene qublety a Ae dere Lae id e E dee lees 6 Memory Operation 0 anane 7 Intercom 2 55 br cis bees edd a Git gol tea ie Tetin Mes lr ae Ga allan er Satta 8 fa ace 9 Intercom Selector Switches 0 0 00 cece eee eee 10 MC602 Room Speaker Operation 0 0 0 cece 12 MC602 Remote Scan Speaker Operation 0 0000 cece eee eee 14 MC602 Hand Held RF Remote Control 0 00 c eee eee eee 15 MC602 Advanced Features 0 00 cece teens 18 MC602 Troubleshooting Tips sasaaa cece teens 19 Statements of Warranty 0 00 teen eae 20 MC602 FEATURES Congratulations Your new Model MC602 is a state of the art Music Center that provides Hands Free Room
9. ROOM SPEAKER MICROPHONE High Fidelity Speaker This also is the microphone for communications from the room 20 ROOM TALK button always active This button is used for talking to the other rooms and to the master To talk to other rooms and the master hold the ROOM TALK button in while talking in the direction of the microphone Release the ROOM TALK button when you are finished talking NOTE When talking to a person in another room you will be heard at each speaker that is in the RAD INT or INT position See section 18 12 21 ROOM LISTEN button always active This button is used for listening to the other rooms and the master To listen to other rooms and the master hold the ROOM LISTEN button in Release the ROOM LISTEN button when you are finished listening NOTE To get the maximum benefit from this Hands Free system make it a house rule that whoever initiates a call will always follow up by pressing the ROOM LISTEN button This allows someone to respond to the call without getting up or stopping their current activities NOTE When listening to other rooms you will hear each speaker including the master that is in the MONITOR RAD INT or INT position See section 18 20 amp 21 DOOR TALK always active These buttons are used for communicating with the outside door speaker s To talk to someone at the door speaker s hold the ROOM LISTEN and ROOM TALK buttons in while talking in the direction of the microphone Release
10. TO OFF TIME mode as described under the TIME SET button 11 VOLUME DOWN button active only when the MC602 is ON This button is used to decrease the audio level volume of the selected source FM AM AUX or TAPE which is sent to all the speakers Whenever this system volume is adjusted the display will show the level of this volume with a number from 1 minimum volume to 32 maximum volume Each Room Speaker including the MASTER SPEAKER has its own volume control which can be used to turn down the audio level for each particular room The VOLUME DOWN button is also used to decrement the time when the unit is in the SET TIME SET AUTO ON TIME or SET AUTO OFF TIME mode as described under the TIME SET button NOTE For best performance the individual speaker volume controls should be turned to maximum volume fully clockwise and then the VOLUME UP and DOWN buttons adjusted for the proper listening volume this is really setting the maximum listening volume The individual speaker volume control can then be adjusted in rooms which require less volume IMPORTANT Do not set this system volume to a high number and then adjust all individual speaker volume controls down to acceptable listening level This is very inefficient will cause the amplifier to overheat and will add distortion to the system 10 amp 11 OPTIONAL DOOR RELEASE always active If the system is set up to use the Door Gate release function the VOLUME UP butt
11. ach customer and installation is unique the MC602 can be configured with monitor override when it is installed If the MC602 is configured with monitor override all intercom communications including the door chime will be heard 10 from the speaker being monitored See Appendix A for details on changing the monitor override configuration Your MC602 may be equipped with either a 3 note or an 8 note Door Chime This optional chime rings through the Master speaker or any room speaker and mutes the radio when the doorbell button is pressed IMPORTANT At least one speaker Master or Room Speaker must be in the RADIO INT or INT position for the Door Chime to function The volume of the chime is controlled at each speaker with the speaker volume CONTROL To make your MC602 easier to use you should label the INTERCOM SELECTOR SWITCHES Remove the door that covers the switches by pulling it straight out Turn the radio ON but move all the INTERCOM SELECTOR SWITCHES to OFF Move one switch at a time to RADIO INT to determine the location it controls On the back of the door write with pen or pencil in the corresponding box which room each switch controls 11 MC602 ROOM SPEAKER OPERATION SPEAKER VOLUME MUSIC VOLUME ROOM DOWN OFF UP ON LISTEN TALK Lal 1 to H a SCAN iij Looor TALK J 19
12. anyone else Lis Z oo Ow O SO oa iS gt o Z Z gt SOURCE CE Dh i Mle Dl Hand Held RF Remote Control 1 SOURCE button active only when the MC602 is ON This button is used to select the audio source FM AM AUX input or TAPE input which the MC602 will output to the Music Speakers Each time the SOURCE button is momentarily pressed the audio source changes The sequence is FM AM AUX TAPE and back 16 to FM 2 UP button active only when the MC602 is ON and the FM or AM source is selected This button is used to scan up through the FM or AM memory presets To go up to the next preset the UP button is simply pressed momentarily The MC602 will tune in the next preset station the sequence is A1 A2 A3 A4 B1 B2 B3 B4 A1 A2 The band will not change stays in AM or FM NOTE If the P1 and P2 jumpers are set to the strong station scanning mode then the UP button will scan to the next strong station just like the TUNING UP button automatic search See section 8 on the master 3 DOWN button active only when the MC602 is ON and the FM or AM source is selected This button is used to scan down through the FM or AM memory presets To go down to the next preset the DOWN button is simply pressed momentarily The MC602 will tune in the previous preset station the sequence is B4 B3 B2 B1 A4 A3 A2 A1 B4 B3 The band will not change sta
13. e communicating with the person at the door and or you do not want to listen to the door speaker the 25 second listening time can be canceled by momentarily pressing either the ROOM LISTEN or the ROOM TALK button by itself NOTE When communicating with the person at the door s both sides of the conversation will be heard at each speaker that is in the RAD INT or INT position See section 18 14 BASS CONTROL Recommended setting 12 00 This CONTROL is used to adjust the low tones of the audio heard on all the speakers room speakers as well as the MASTER SPEAKER Turning the BASS CONTROL clockwise increases the bass makes the low frequencies louder and turning it counter clockwise decreases the bass makes the low frequencies quieter 15 TREBLE CONTROL Recommended seiting 12 00 This CONTROL is used to adjust the high tones of the audio heard on all the speakers room speakers as well as the MASTER SPEAKER Turning the TREBLE CONTROL clockwise increases the treble makes the high frequencies louder and turning it counter clockwise decreases the treble makes the high frequencies quieter 16 INTERCOM VOLUME CONTROL Recommended seiting 12 00 This CONTROL is used to adjust the level of the intercom communications Turning the INTERCOM VOLUME CONTROL clockwise increases the volume of intercom communications and turning it counter clockwise decreases the volume The INTERCOM VOLUME CONTROL should be set to a point where intercom
14. e only when the MC602 is ON and the FM or AM source is selected These buttons are used to save and recall your most frequently used FM and AM radio stations presets Along with the SOURCE button these buttons provide 8 FM memories A1 A2 A3 A4 B1 B2 B3 and B4 and another 8 AM memories A1 through B4 To save a radio station in memory FM B3 f Using the SOURCE button change the source to FM B 2 Tune the radio to the station which is desired to be saved 3 Hold in the 3 button until a 3 appears as the memory number To recall the radio station saved in memory AM A2 f Using the SOURCE button change the source to AM A 2 Momentarily press the 2 button The memory number should display 2 and the station that was stored in memory A2 should be displayed and heard through the speakers AM IDBU 2 KHz Display 10 VOLUME UP button active only when the MC602 is ON This button is used to increase the audio level volume of the selected source FM AM AUX or TAPE which is sent to all the speakers Whenever this system volume is 6 increased the display will show the level of this volume with a number from 1 minimum volume to 32 maximum volume Each Room Speaker including the MASTER SPEAKER has its own volume control which can be used to turn down the audio level for each particular room The VOLUME UP button is also used to increment the time when the unit is in the SET TIME SET AUTO ON TIME or SET AU
15. he MC602 must be turned on to operate the radio or to listen to other music through the unit Setting the times and auto functions as well as all intercom functions will work with the power ON or OFF AM FM AUX Display 4 AUTO b button This button is used to turn the Automatic Music AUTO 3 function ON and OFF Pressing the AUTO gt button momentarily turns the function ON and pressing it again turns it OFF The AUTO function is ON when the AUTO indicator is displayed on the top of the display When the AUTO function is turned on the MC602 will turn itself ON Automatically when the current time reaches the Automatic ON TIME and then turn itself OFF when the current time reaches the Automatic OFF TIME When the MC602 automatically turns itself ON it will always turn on at the same volume level This AUTO ON VOLUME LEVEL has a default of 6 See Sections 10 amp 11 but it can be changed following these simple steps A Turn the MC602 ON B Momentarily press the VOLUME UP and AUTO 4 buttons at the same time Release both buttons C The display will show the letter A for AUTO ON VOLUME followed by anumber This number is the volume of the music currently playing and this will be the volume of the MC602 when it automatically turns ON D This AUTO ON VOLUME can be changed by using the VOLUME UP amp DOWN buttons E When you have the volume at the level that you want the MC602 to automatically turn on to do n
16. iginally installed This warranty extends to the original user of the product and to each subsequent owner of the product during the term of this warranty M amp S SYSTEMS will repair or replace at its option parts and materials at no charge Parts supplied under this warranty may be new or rebuilt at the option of M amp S SYSTEMS If during the limited warranty period it appears as though this product contains a defect which is covered by this limited warranty call our toll free service number before dismantling the product 1 800 877 6631 Remember to attain a Return Authorization Number RAN before returning any product to M amp S SYSTEMS Send this product freight pre paid and insured to our service center for warranty repair You will be advised on shipping instructions when you call the toll free service number M amp S SYSTEMS will return the repaired product freight pre paid within the U S A The installing dealer or distributor may assist you at your choice and expense with returning product for repair Please include a brief description of the problem and a dated proof of purchase receipt with any product that is returned for warranty repair ANY PRODUCT RETURNED WITHOUT A RETURN AUTHORIZATION NUMBER WILL BE REFUSED THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON
17. iously to increment or decrement the AUTO OFF TIME 4 minutes 6 SOURCE buiton active only when the MC602 is ON This button is used to select the audio source FM A FM B AM A AM B AUX input or TAPE input which the MC602 will output to the speakers The A and B following FM and AM indicate the preset memory bank selection The A bank indicates the first four preset memories A1 A2 A3 and A4 while the B bank indicates the second four preset memories B1 B2 B3 and B4 The use of the memory banks is explained in paragraph 10 Each time the SOURCE button is momentarily pressed the audio source changes The active source is displayed on the right side of the display the memory bank indicator is on the right side of the display after MEM 103 Display 7 TUNING DOWN button active only when the MC602 is ON and the FM or AM source is selected This button is used to scan down through the FM or AM radio stations The radio stations can be scanned down in two ways using this button 1 To scan down until the next strong station is found Automatic Search the TUNING DOWN button is simply pressed momentarily The audio will be muted and the display will show the radio station frequency decreasing until a strong station is found Once the MC602 locks onto a strong station it will stop scanning This station s frequency will be shown on the display and the audio will again be heard through the speakers 2 To scan d
18. isfying home living experience MC602 MASTER UNIT OPERATION usten OMS 6 5 4 3 11 10 13 12 When the MC602 is first connected to 120V house power the unit will set itself to 12 00 AM and the time will flash The flashing display indicates that power has been applied to the unit for the first time or that there has been an extended power outage and the unit has lost its memory The unit will operate properly and keep time from this initial 12 00 AM setting but it should have its memory restored by performing sections 4 5 and 9 in the following instructions 1 MASTER SPEAKER MICROPHONE High Fidelity Speaker This also is the microphone for communications from the master unit 2 DISPLAY Easy to read and understand Liquid Crystal Display with backlight The display normally functions as a clock or frequency readout for AM and FM but the display can also show additional important information This other 2 information is explained under the function with which it is associated 3 POWER button This button is used to turn the MC602 ON and OFF When the unit is turned on one of the four source indicators AM FM AUX or TAPE on the right side of the display will be SHOWN When the unit is off all four of these annunciators will be off T
19. of the three jumpers P1 P2 and P3 on the back of the master next to the terminal block for the green wires The MC602 comes from the factory with only the P1 pins jumpered the other jumper is on only 1 pin of P2 in case it is needed In this configuration the monitored room does not hear any intercom communication or the chime The MC602 can also be configured for MONITOR OVERRIDE This is done by removing the jumper from the P1 pins inserting it on both P3 pins and moving the P2 jumper onto both P2 pins A pair of needlenose pliers may be necessary to move the jumpers In MONITOR OVERRIDE the monitored room hears all intercom communications including the chime APPENDIX B Station Scanning The way that the SCAN function works is dependant on the configuration of the two jumpers P1 and P2 behind the face panel just above and to the right of the display on the master The following table shows how the SCAN function operates 1 PRESETS PRESETS FM A1 A2 A3 A4 BI B2 B3 B4 AM Al A2 A3 A4 B1 B2 B3 B4 AUX J TAPE J ml _ f Y PRESETS i PRESETS FM A1 A2 A3 A4 BI B2 B3 B4 AM A1 A2 AZ A4 B1 B2 B3 B4 AUX 4 TAPE m FM STRONG E STRONG EAN Da _ _ Default factory setting i PRESETS PRESETS g g FM Al A2 A3 A4 B1 B2 B3 B4 AM Al A2 A3 A4 B1 B2 B3 B4 AUX TAPE 18 MC
20. on and VOLUME DOWN button are used to open the Entry Door or Gate The Door Gate release is activated by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds The display will show door when the buttons are pressed at the same time and it will show RELS when the door release is activated 10 amp 11 OPTIONAL HOME AUTOMATION INTERFACE always active If the system is connected with a HOME AUTOMATION system the VOLUME UP button and VOLUME DOWN button are used to activate turn on the automated function 7 The function is turned on by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds 10 amp 11 OPTIONAL SECURITY INTERFACE always active If the system is connected with a SECURITY system the VOLUME UP button and VOLUME DOWN button are used to activate the panic alarm The panic alarm is turned on by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds 12 ROOM TALK button always active This button is used for communicating with the other rooms To talk to someone in another room hold the ROOM TALK button in while talking in the direction of the microphone The display will show that you are in the talk mode Release the ROOM TALK button when you are finished talking NOTE When talking to a person in another room you will be heard at each speaker that is in the RAD INT or INT position See
21. ot press any buttons for 9 seconds The display will go back to normal and the new AUTO ON VOLUME will be saved A 7 Display 3 5 TIME SET button This button is used to access the time setting mode When the TIME SET button is pressed momentarily the display will indicate SET TIME and the current time will be displayed with the hours flashing The UP and DOWN buttons either TUNING UP and DOWN or VOLUME UP and DOWN can then be used to increment or decrement the current time hours Pressing the UP button or DOWN button momentarily will increment or decrement the hours by one each time the key is pressed Holding the UP button or DOWN button depressed will rapidly increment or decrement the hours until the button is released The time display also includes the AM or PM indicator which is changed by scrolling the hours past 12 00 Note The MC602 remains in the set mode for 25 seconds with no activity no buttons being pressed after which the unit automatically returns to the normal mode of operation The TIME SET button must be pressed again to return to the set mode Once the current hours have been set correctly momentarily press the TIME SET button again The display will indicate SET TIME and the current time will be shown with the minutes flashing The UP and DOWN buttons can be used as described previously to increment or decrement the current time minutes Once the current minutes have been set correctly momentaril
22. own to a specific frequency and or hear the stations as they are scanned Manual Scan the TUNING DOWN button is held in After about 1 second the MC602 will go into Manual Scan Down mode and the display will decrement in frequency while the audio at this frequency will be heard The unit will continue to decrement and play each frequency until the TUNING DOWN button is released The Manual scan can be used to select a station that is not strong enough to be picked up by the Automatic Search to scan through many frequencies without stopping on each strong station or to quickly hear a sample of each station as it is scanned NOTE To decrement the frequency down just once the TUNING DOWN button should be held in until the frequency changes then immediately released The TUNING DOWN button is also used to decrement the time when the unit is in the SET TIME SET AUTO ON TIME or SET AUTO OFF TIME mode as described under the TIME SET button 8 TUNING UP button active only when the MC602 is ON and the FM or AM source is selected This button is used to scan up through the FM or AM radio stations This button operates the same Automatic Search and Manual Scan as the TUNING DOWN button except that it scans the frequencies up instead of down The TUNING UP is also used to increment the time when the unit is in the SET TIME SET AUTO ON TIME or SET AUTO OFF TIME mode as described under the TIME SET button 9 1 2 3 and 4 buttons activ
23. s turned on by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds 15 OPTIONAL HAND HELD RF REMOTE CONTROL PROGRAMMING Upon initial power up of the MC602 or upon applying power after the unit loses its memory power outages greater than 2 hours the unit must be programmed or taught the unique code that is present in the REMOTE CONTROL TRANSMITTER To do this the MC602 must be put into its test mode by momentarily pressing the VOLUME UP and SOURCE buttons at the same time The display on the MC602 should show TEST Now press the TUNING UP button on the REMOTE CONTROL TRANSMITTER until the display flashes SAVE twice The MC602 has now learned the TRANSMITTER If more than one transmitter is to be used with the system the second third and fourth transmitters must be learned by pressing the TUNING DOWN VOL UP and VOL DOWN on the respective TRANSMITTER Always press a different button for each TRANSMITTER to be programmed The test mode is exited by momentarily pressing the VOLUME UP and POWER buttons at the same time OPERATION Your MUSICAL INTERCOM HAND HELD CONTROLLER is an RF remote control which means that it will work anywhere in or around your house you do not have to be in the same room as the master The system also has a unique code in the transmitter that is learned by the MC602 virtually insuring that no one else can interfere with your system and you will not interfere with
24. section 18 13 ROOM LISTEN button always active This button is used for listening to the other rooms To listen to other rooms hold the ROOM LISTEN button in The display will show that you are in the listen mode Release the ROOM LISTEN button when you are finished listening NOTE To get the maximum benefit from this Hands Free system make it a house rule that whoever initiates a call will always follow up by pressing the ROOM LISTEN button This allows someone to respond to the call without getting up or stopping their current activities NOTE When listening to other rooms you will hear each speaker that is in the MONITOR RAD INT or INT position See section 18 12 amp 13 DOOR TALK always active These buttons are used for communicating with the outside door speaker s To talk to someone at the door speaker s hold the ROOM LISTEN and ROOM TALK buttons in while talking in the direction of the microphone The display will show that you are in the talk mode Release the ROOM LISTEN and ROOM TALK buttons when you are finished talking the MC602 will automatically listen you will hear what is being said to the person at the door s for approximately 25 seconds The display will show that you are in the listen mode You may talk to the person at the door again anytime by holding in the ROOM LISTEN and ROOM TALK buttons Each time the buttons are released the door speaker s can be listened to for another 25 seconds If you are don
25. ted the SCAN function will step through the 8 memory presets of the source that is selected then advance to the next source The SCAN function will step from AUX to TAPE and from TAPE to FM preset A1 For example if the current source is FM and preset B4 is tuned in executing the SCAN will tune in preset A1 in the AM band Executing SCAN again will tune in preset A2 in the AM band If the MC602 has the TAPE source selected executing the SCAN function will change the source to FM and tune in preset A1 Executing SCAN again will turn in preset A2 in the FM band 23 amp 24 OPTIONAL DOOR RELEASE always active If the system is set up to use the Door Gate release function the VOLUME UP button and VOLUME DOWN button are used to open the Entry Door or Gate The Door Gate release is activated by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds 14 23 amp 24 OPTIONAL HOME AUTOMATION INTERFACE always active If the system is connected with a HOME AUTOMATION system the VOLUME UP button and VOLUME DOWN button are used to activate turn on the automated function The function is turned on by pushing both the VOLUME UP and VOLUME DOWN buttons at the same time and holding them for 4 seconds 23 amp 24 OPTIONAL SECURITY INTERFACE always active If the system is connected with a SECURITY system the VOLUME UP button and VOLUME DOWN button are used to activate the panic alarm The panic alarm i
26. ter clockwise Just remember that you will not hear the intercom or door chime with the VOLUME CONTROL in this position 13 OPTIONAL REMOTE SCAN SPEAKER OPERATION 23 MUSIC VOLUME UP ON button always active This button is used to increase the audio level volume of the selected source FM AM AUX or TAPE which is sent to all the speakers The MUSIC VOLUME UP ON button can also be used to turn the MC602 ON if it is OFF To turn the MC602 ON momentarily press the MUSIC VOLUME UP ON button 24 MUSIC VOLUME DOWN OFF buiton active only when the MC602 is ON This button is used to decrease the audio level volume of the selected source FM AM AUX or TAPE which is sent to all the speakers The MUSIC VOLUME DOWN OFF button can also be used to turn the MC602 OFF To turn the MC602 OFF press the MUSIC VOLUME DOWN OFF button after the volume has decreased to its minimum level 23 amp 24 SCAN active only when the MC602 is ON This function is used to change memories and or sources Momentarily pressing both the MUSIC VOLUME UP and DOWN butions at the same time will execute the SCAN function The way that the SCAN function works is dependant on the configuration of the two jumpers P1 and P2 behind the face panel on the master that were set when the MC602 was installed The factory default mode of operation is described here Appendix B describes the other modes and how to change modes If the MC602 has the FM or AM source selec
27. y press the TIME SET button again to return to the normal mode or let the MC602 automatically return to the normal mode if no buttons are pressed for 25 seconds To set the AUTO gt ON and OFF times the TIME SET button must be momentarily pressed three times without changing the current time After pressing the TIME SET button for the third time the display will indicate SET AUTO ON TIME and the auto on time will be displayed with the hours flashing The UP and DOWN buttons can be used as previously described to increment or decrement the auto on time hours Once the AUTO ON TIME hours have been set correctly momentarily press the TIME SET button again The display will indicate SET AUTO ON TIME and the AUTO ON TIME will be displayed with the minutes flashing The UP and DOWN buttons can be used as previously described to increment or decrement the AUTO ON TIME minutes Once the AUTO ON TIME minutes have been set correctly momentarily press the TIME SET button again The display will indicate SET AUTO OFF TIME and the AUTO OFF TIME will be displayed with the hours flashing The UP and DOWN buttons can be used as previously described to increment or decrement the AUTO OFF TIME hours Once the AUTO OFF TIME hours have been set correctly momentarily press the TIME SET again The display will indicate SET AUTO OFF TIME and the AUTO OFF TIME will be displayed with the minutes flashing The UP and DOWN buttons can be used as described prev
28. ys in AM or FM NOTE If the P1 and P2 jumpers are set to the strong station scanning mode then the DOWN button will scan to the next strong station just like the TUNING DOWN button automatic search See section 7 on the master Note To change the function of the TUNING UP and DOWN buttons to select all strong stations instead of memory presets select the SCAN STATIONS mode as shown in Appendix B 4 VOLUME UP ON button always active This button is used to increase the audio level of the selected source FM AM AUX or TAPE which is sent to all the Music Speakers Pressing this button also turns the MC602 ON if it is OFF 5 VOLUME DOWN OFF button active only when the MC602 is ON This button is used to decrease the audio level of the selected source FM AM AUX or TAPE which is sent to all the Music Speakers Pressing this button also turns the MC602 OFF when its audio level is all the way down NOTE For best performance the individual music speaker volume controls should be turned to maximum volume fully clockwise and then the volume adjusted with the 17 VOLUME buttons on the MCTX HAND HELD CONTROLLER for the proper listening volume this is really setting the maximum listening volume The individual music speaker volume control can then be adjusted in rooms which require less volume ADVANCED FEATURES APPENDIX A Monitor Override The way that the MONITOR function works is dependant on the configuration
Download Pdf Manuals
Related Search