Makita 5014NB User's Manual
Contents
1. Chain Saw 340 mm 13 3 8 MODEL 5014NB 375 mm 14 3 4 MODEL 5016NB INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS Chain speed Length of Saw chain Overall FPM guide bar Gadde length 1 300 340 mm 9 5 mm 1 27 mm 760 mm 13 3 8 3 8 0 050 30 1 300 375 mm 9 5 mm 1 27 mm 795 mm f 14 3 4 3 8 0 050 31 1 4 Manufacturer reserves the right to change specifications without notice Note Specifications may differ from country to country 5014NB 5016NB IMPORTANT SAFETY INSTRUCTIONS WARNING WHEN USING AN ELECTRIC CHAIN SAW BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK AND INJURY TO PERSONS INCLUDING THE FOLLOWING 1 READ ALL INSTRUCTIONS Keep Work Area Clean Cluttered areas invite injuries Do not start cutting until you have a clear work area secure footing and a planned retreat path from the falling tree Consider Work Area Environment Use extreme caution when cutting small size brush and saplings because the slender material may catch the saw chain and be whipped toward you or pull you off balance Do not operate a chain saw in a tree unless specifi cally trained to do so When cutting a limb that is under tension be alert for spring back so that you wili not be struck when the tension in the wood fibers is released Don t expose chain saw to rain Don t use chain saw in damp or2. 1 Nozzie A 89 2 Pan Head Screw M4x6 With Washer 33 1 Cap 90 1 Switch 40 1 Oil Vessel 91 1 Rubber Pin 4 41 1 Check Valve 92 1 Handle Set With ttem 100 42 1 Tube 3 93 4 Pan Head Screw M5x18 With Washer 43 3 Pan Head Screw M4x12 With Washer 94 1 Rubber Pin 4 44 2 i O Ring 3 96 1 Cord Guard 45 1 Plunger 97 1 Cord 46 4 Gear Housing 98 1 Strain Relief 47 1 Pin 6 99 2 Pan Head Screw M4x18 With Washer 48 1 Chain Catcher 100 1 Handle Set With Item 92 49 1 Clutch Cam 101 2 Pan Head Screw M4x28 With Washer 50 1 Flat Washer 10 102 1 Safety Cover 51 1 i Ring 5 103 J Pan Head Screw M5x22 With Washer 52 a Thin Washer 6 900 1 Leat Spring 53 1 Flat Washer 5 Note The switch and other part specifications may differ from country to country 21 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase Should any trouble develop during this one year period return the COMPLETE tool freight prepaid to one of Makita s Factory or Authorized Service Centers If inspection shows the trouble is caused by defective workmanship or material Makita will repair or at our option replace without charge This Warranty does not apply where repairs have been made or attempted by others e repairs are r
3. ground Remove the small limbs in one cut as shown in Fig 18 Branches under tension should be cut from the bottom up to avoid binding the chain saw 14 LIMB CUT Keep work off ground Leave support limbs until log is cut Fig 18 Bucking a log Bucking is cutting a log into lengths It is important to make sure your footing is firm and your weight is evenly distributed on both feet When possible the log should be raised and supported by the use of limbs logs or chocks Follow the simple directions for easy cutting When the log is supported along its entire length as shown in Fig 19 it is cut from the top overbuck Cut from top overbuck avoid cutting earth Fig 19 When the log is supported on one end as shown in Fig 20 cut 1 3 the diameter from the underside underbuck Then make the finished cut by overbucking to rN eras aa meet the first cut to meet 1st cut to avoid pinching Tst cut underbuck 1 3 diameter to avoid splintering ts we i Fig 20 When the log is supported on both ends as shown in Fig 21 cut 1 3 of that diameter from the top overbuck Then make the 1st cut eo bad 1 3 diameter finished cut by underbucking the lower 2 3 Gaava d esliotering to meet the first cut nas i Q AE RETRA Oe 2nd cut underbuck 2 3 diameter to meet 1st cut to avoid pinching Fig 21 15 When bucking on a slope always stand on the uphill side of the log as s
4. use Use an extension cord heavy enough to carry the current the tool will draw Undersize cord will cause a drop in line voltage resulting in loss of power and over heating Make sure the exten sion cord is in good condition before using Keep the cord away from the cut ting area and to position cord so that it will not be caught on branches and the like during cutting Use the table below to determine the proper wire size re quired in the extension cord Ampere rating on nameplate Ext Cord Length Wire Size American Wire Gauge 25 Ft 50 Ft 75 Ft 100 Ft 125 Ft 150 Ft Contact Makita Authorized or Factory Service Center if a proper extension cord cannot be found SAVE THESE INSTRUCTIONS Chain Saw Nomenclature LEFT SIDE Front handle Saw chain Lock off button Rear handle Cord m seen _If S gan Guide bar Trigger switch RIGHT SIDE Guide bar nose Guard protector aa a ma am Im _ Eai r _ mm oe oo oo on mm e Guide bar Sprocket mounting pad Fig 1 Bar Tip Guard An attachment that may be provided on the end of the guide bar to prevent the chain at the end of the guide bar from contacting the wood Bucking The process of cross cutting a felled tree or log into lengths Chain Brake A device used to stop the chain saw Chain Saw Powerhead A chain saw without the saw chain and guide bar Clutch A mechanism for connecting a
5. cated automatically when the motor is running Check the oil level in the oil tank through the window on the gear housing cover Gear housing cover To replenish the oil take off the cap on the tank and fill with the oil supply The oil tank capacity is 170 cc 5 5 oz Fig 9 CAUTION Turbine oi 200 or machine oil is recommended A special oil or one of high viscosity is neither needed nor advisable since the aim is to lubricate the chain and the guide bar Do not use dirty oil nor volatile oil Switch action To prevent the trigger from being acciden Trigger switch tally pulled a lock off button is provided as a safety feature pecs On Punen To start the tool press in the lock off button and pull the trigger Release the trigger to stop CAUTION Before plugging in the tool always check to see that the trigger switch actuates properly and returns to the OFF position when released 10 Hook Power cord When using an extension cord secure it Cord connector to the tool s cord with the hook provided Attach the hook about 100 200 mm 4 8 from the extension cord connector This will help prevent unintentional dis connection Extension cord Fig 11 Cutting operation Turn the too on and allow the chain to reach full speed before it contacts the wood Be sure the chain is adequately lubricated Use the spike as a pivot point and ease the tool into the wood rocking it in gent
6. ecified by the manufacturer Power Supply Connect chain saw to correct voltage that is be sure that the voltage supplied is the same as that specified on the nameplate of the tool Replacement Parts When servicing use only identical replacement parts Wear ear protectors during operation Before making a felling cut remove dirt stones loose bark nails staples and wire from the tree Secure the log so that it will not roll or move suddenly during operation AVOID UNINTENTIONAL STARTING Don t carry plugged in tool with finger on switch Be sure switch is OFF when plugging in Attention Do not expose this tool to rain and pull plug immediately if the supply cable be damaged or cut The chain saw must not be left outdoors during rain and it must not be used when wet VOLTAGE WARNING Before connecting the tool to a power source receptacle outlet etc be sure the voltage supplied is the same as that specified on the nameplate of the tool A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user as well as damage to the tool If in doubt DO NOT PLUG IN THE TOOL Using a power source with voltage less than the nameplate rating is harmful to the motor Use Of Extension Cord If the extension cord is intended to be used outdoors the cord shall be marked with the suffix W A following the cord type designation for example SJTW A to indicate it is acceptable for outdoor
7. equired because of normal wear and tear The tool has been abused misused or improperly maintained e alterations have been made to the tool IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CON SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A SPECIFIC PURPOSE AFTER THE ONE YEAR TERM OF THIS WARRANTY This Warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi 446 Japan 883465 061 PRINTED IN JAPAN 1991 11 N
8. ere felling cuts are to be made Notching undercut Make the notch 1 3 the diameter of the tree perpendicular to the direction of fall as shown in Fig 17 Make the lower horizontal notching cut first This will help to avoid pinching of either the saw chain or the guide bar when the second notch is being made 13 Felling back cut Make the felling back cut at least 2 inches 50 8 mm higher than the horizontal notch ing cut as shown in Fig 17 Keep the fell ing back cut parallel to the horizontal notching cut Make the felling back cut so enough wood is left to act as a hinge The hinge wood keeps the tree from twisting and falling in the wrong direction Do not cut through the hinge Direction back cut ean 1 2 inches Hinge Fig 17 As the felling cut gets close to the hinge the tree should begin to fall If there is any chance that the tree may not fall in the desired direction or it may rock back and bind the saw chain stop cutting before the felling back cut is complete and use wedges of wood plastic or aluminum to open the cut and drop the tree along the desired line of fall When the tree begins to fall remove the chain saw from the cut stop the motor put the chain saw down then use the retreat path planned Be alert for overhead limbs falling and watch your footing Limbing a tree Limbing is removing the branches from a fallen tree When limbing leave larger lower limbs to support the log off the
9. hain cover Fit one end of the chain over the sprocket and the other over the end of the guide bar Notice that the cutters must be in the direction of the arrow in Fig 3 and 4 Keep the chain in the guide bar grooves Sprocket Adjust pin Cutter ie Fig 4 Install the guide bar so that the lower hole in the guide bar is just over the adjusting pin Install the chain cover and tighten the hex bolt only tight enough to hold the guide bar temporarily Adjusting saw chain tension CAUTION Always be sure that the tool is switched off and unplugged before adjusting chain tension Grasp the chain in the middle of the guide bar and lift up The gap between the side oo l Side link of chain link of the chain and the guide bar should k be about 3 mm to 4 mm 1 8 5 32 ae ee Guide bar Fig 5 if the gap is not about 3mm to 4mm 1 8 5 32 adjust the chain tension Chain tension Use a screwdriver to turn the chain tension spleen acew adjusting screw clockwise for more tension or counterclockwise for less tension When adjusting the chain tension lift the end of the guide bar slightly After adjusting the chain tension use the socket wrench to tighten the hex bolt securely Chain cover Fig 7 CAUTION When breaking in a new chain adjust the tension often since it tends to stretch Lubrication This tool is equipped with an automatic lubrication system so the chain is lubri
10. he chain cover Turn the tool on and depress the oil button 4 or 5 times e Cover the saw chain and the guide bar with the scabbard To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers always using Makita replacement parts 18 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner e Socket wrench 13 Screwdriver e File Part No 782212 4 Part No 783001 0 Part No 744003 1 Scabbard Oil supply Cap for oil supply Part No 414593 5 Part No 181117 9 Part No 242012 9 Saw chain e Hook Part No 713014 7 For 5014NB Part No 158024 1 Part No 713015 5 For 5016NB CS 19 Aug 25 88 US CHAIN SAW 340 mm 13 3 8 Model 5014NB 375 mm 14 3 4 Model 5016NB Note The switch noise suppressor and other part configurations may differ from country to country 20 MODEL 5014NB 5016NB Aug 25 88 US ITEM NO ITEM NO NO USED DESCRIPTION NO USED DESCRIPTION a ee a ee oo MACHINE MACHINE 17 od Guide Bar 54 1 Pan Head Screw M5x16 With Washer 2 1 Protector 55 6 Pan Head Screw M4x10 With Washer 3 1 Packing 56 1 Slider Plate 4 1 Suppor
11. hown in Fig 22 When cutting through to maintain complete control release the cutting pres sure near the end of the cut without re laxing your grip on the chain saw handles Don t let the chain contact the ground After completing the cut wait for the saw chain to stop before you move the chain saw Always stop the motor before moving from tree to tree Carrying tool Carry the tool by the front handle with the tool turned off finger off the switch the guide bar and the saw chain to the rear Use the scabbard to cover the guide bar and the saw chain 16 Stand on uphill side when cutting because log may roll Fig 22 Scabbard Front handle Fig 23 MAINTENANCE CAUTION Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance Filling saw chain To get the most in cutting performance from your tool you must keep the cutter sharp and filed properly as shown below TOP PLATE ANGLE SIDE PLATE ANGLE TOP FILING ANGLE Cutter Raker 309 A top plate angle of File the side plate to lf you have filed the top 30 is ideal 85 and side plate correctly the top filling angle will be 60 automatically Fig 24 To file the saw chain push the file in the direction of the arrow When pulling it back be careful not to touch the cutters with the file Saw chain Fig 25 After a saw chain has been filed two or three times
12. laced by authorized service center Do not use chain saw if switch does not turn it on and off Do not operate a chain saw that is damaged improperly adjusted or is not completely and securely assembled Be sure that the saw chain stops moving when the trigger is released Guard Against Kickback WARNING KICKBACK may occur when the nose or tip of the guide bar touches an object or when the wood closes in and pinches the saw chain in the cut Tip contact in some cases may cause a lightning fast reverse reaction kicking the guide bar up and back towards the operator Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator Either of these reactions may cause you to lose control of the saw which could result in serious injury to user The following precautions should be followed to minimize kickback 17 18 19 20 21 22 23 24 1 Grip saw firmly Hold the chain saw firmly with both hands when the motor is running Use a firm grip with thumbs and fingers encircling the chain saw handles 2 Do not over reach 3 Keep proper footing and balance at all times 4 Don t let the nose of the guide bar contact a log branch ground or other obstruction 5 Don t cut above shoulder height 6 Use devices such as low kickback chain chain brakes and special guide bars that reduce the risks associated with kickback 7 Only use replacement bars and chains sp
13. lding the chain saw Always grip each handle with the thumb and fingers encircling the handle as shown Use this grip in Fia 15 thumb below in Fig 15 handle Fig 15 12 Using the chain saw Always be sure of your footing and hold the chain saw firmly with both hands while the motor is running Felling a tree When bucking and felling operations are being performed by two or more persons at the same time the felling operation should be separated from the bucking operation by a distance of at least twice the height of the tree being felled Trees should not be felled in a manner that would endanger any person strike any utility line or cause any property damage If the tree does make contact with any utility line the utility company should be notified immediately The chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled A retreat path should be planned and cleared as necessary before cuts are started The retreat path should extend back and Retreat diagonally to the rear of the expected line of fall as shown in Fig 16 ata Direction of fall ff min R di at wpa a ee oes Fae 4 p H Fig 16 Before felling is started consider the natural lean of the tree the location of larger branches and the wind direction to judge which way the tree will fall Remove dirt stones loose bark nails staples and wire from the tree wh
14. lity Keep cord clear of the chain and operator at all times Never carry saw by the cord or pull it to disconnect from receptacle Keep cord from oil and sharp edges Inspect extension cords periodically and replace if damaged Keep tools sharp and clean for better and safer perfor mance Follow instructions for lubricating and changing accessories Keep handles dry clean and free from oil and grease Disconnect Chain Saw Disconnect chain saw when not in use before servicing and when changing accessories and attachments such as saw chain and guard Outdoor Use Extension Cords Use only extension cords intended for use outdoors and so marked Stay Alert Watch what you are doing Use common sense Do not operate chain saw when you are tired Keep all parts of the body away from the saw chain when the motor is operating Before you start the saw make sure the saw chain is not contacting anything Check Damaged Parts Before further use of the chain saw a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless other wise indicated elsewhere in this instruction manual Have defective switches rep
15. ly Do not force the guide bar in as this may cause overload and overheating Fig 12 Instant chain brake This tool is equipped with an instant chain brake to reduce the risk caused by kickback To actuate the instant chain brake push the protector forward Protector Fig 13 CAUTION As soon as the instant chain brake actuates turn the tool off Keeping the motor running with the chain brake actuated may cause damage to the tool 11 To release the chain brake reset the pro tector to the exact original position after turning the tool off Fig 14 WARNING e Under normal circumstances it should never be necessary to intentionally release the chain brake while the tool is running Occasionally after the brake has been actuated the protector may not reset to the exact original position If this happens place the tool on a flat surface in a clear area away from other persons or objects that might contact the saw chain Then turn the tool on After running the tool for a couple of seconds turn the tool off While the motor is coasting reset the protector with the same hand you used to turn the tool on Hold the tool firmly by grasping the front handle with the other hand Careless handling of the tool at this time could result in serious injury therefore use extreme caution when resetting the chain brake in this manner e Before operation always check to see that the chain brake actuates properly Ho
16. nd disconnecting a driven member to and from a rotating source of power Drive Sprocket or Sprocket The toothed part that drives the saw chain Felling The process of cutting down a tree Felling Back Cut The final cut in a tree felling operation made on the opposite side of the tree from the notching undercut Front Handle The support handle located at or toward the front of the chain saw 6 Front Handle Guard A structural barrier between the front handle of a chain saw and the guide bar typically located close to the hand position on the front handle and sometimes employed as an activating lever for a chain brake Guide Bar A solid railed structure that supports and guides the saw chain Kickback The backward or upward motion or both of the guide bar occurring when the saw chain near the nose of the top area of the guide bar contacts any object such as a log or branch or when the wood closes in and pinches the saw chain in the cut Kickback Pinch The rapid pushback of the saw which can occur when the wood closes in and pinches the moving saw chain in the cut along the top of the guide bar Kickback Rotational The rapid upward and backward motion of the saw which can occur when the moving saw chain near the upper portion of the tip of the guide bar contacts an object such as a log or branch Low Kickback Chain A chain that complies with the kickback performance requirements of ANSI B175 1
17. ter Plate 57 1 Hex Socket Head Bolt M6 5 1 Brake Lever 58 1 Gear Housing Cover 6 2 Pan Head Screw M5x16 With Washer 59 2 Pan Head Screw M5x20 With Washer 7 1 Hex Socket Head Bolt M6 60 1 Grip 8 1 Hex Socket Head Bolt M6 63 2 Pan Head Screw M5x16 With Washer 9 1 Packing 62 1 Ball Bearing 6001LLB 10 1 Pan Head Screw M5x12 With Washer 63 4 Flat Washer 12 11 1 Fiat Head Screw M5x40 64 1 Slider 12 1 Adjust Pin 65 1 Fiat Washer 16 13 1 Steel Ball 5 6 66 1 Helical Gear 53 14 1 Compression Spring 4 67 1 Set Screw M8x16 15 1 Tension Spring 6 68 4 Plate 16 1 Cover Plate 69 1 Compression Spring 4 TA 2 Pan Head Screw M4x10 With Washer 70 1 Woodruff Key 5 19 1 Hex Flange Head Bolt M8x17 71 1 Spindle 20 1 Chain Cover 72 1 Flat Washer 17 21 1 Hex Nut M8 13 73 1 Ball Bearing GOOALLB 22 1 Flat Washer 8 74 1 Ball Bearing 6201LLB 23 1 Dust Cover 75 1 Fan 97 24 1 Dust Seal 30 76 1 ARMATURE ASSEMBLY 25 1 Sprocket With Item 74 78 26 1 Pin 6 77 1 Insulation Washer 27 1 Clutch Pressure 78 J Ball Bearing 6200LB8 28 1 Stop Ring E 3 79 2 Hex Bolt M5x70 With Washer 29 1 Compression Spring 5 80 1 Baffle Plate 30 1 Nozzle B 81 1 FIELD ASSEMBLY 31 1 O Ring 8 82 1 Motor Housing 32 1 Compression Spring 3 83 2 Rivet O0 5 33 1 Steel Ball 3 5 84 1 Name Plate 34 1 ORmg 3 85 1 Pan Head Screw M5x20 With Washer 35 1 Casing 86 4 Pan Head Screw M5x50 With Washer 36 1 Filter 87 2 Carbon Brush 37 gt 4 O Ring 9 88 2 Brush Hoider Cap 38 J
18. the raker see Fig 24 may need to be filed down slightly This is because the raker acts as a depth gauge for the cutters As the cutters are filed they lose some height due to their angled shape Eventually the cutters will become lower than the depth gauge and consequently will not be able to cut To remedy this use a flat file to file the tops of the rakers so that they are about 0 5 mm 0 025 below the tips of the cutters see Fig 24 Be careful not to file the rakers excessively or the cutters will be allowed to take too large of a bite causing the tool to stall or snag in the cut 17 Removing chip buildup Chips and sawdust will build up in the guide bar groove and oil hole clogging them and impairing oil flow Remove the guide bar and clean them out Clean out Guide bar this groove Fig 26 Fig 27 Replacing carbon brushes Remove and check the carbon brushes regularly Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only Makita carbon brushes Limit mark Fig 28 Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps Screwdriver Storing the tool Before storing the tool be sure to do the following e Remove the chain cover Remove any chips and sawdust from the tool e Install t
19. wet locations Do not use chain saw in presence of flammable liquids or gases Guard Against Electric Shock Prevent body contact with grounded surfaces For example metal pipes wire fences Keep Children Away Do not let visitors contact chain saw or extension cord All visitors should be kept away from work area Store Idle Chain Saw When not in use chain saws should be stored in a dry and high or locked up place out of the reach of children When storing saw use a scabbard or carrying case Don t Force Chain Saw It will do the job better and safer at the rate for which it was intended Use Right Tool Cut wood only Don t use chain saw for purpose not intended for example Don t use chain saw for cutting plastic masonry non wood building materials Dress Properly Do not wear loose clothing or jewelry They can get caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors Wear protective hair covering to contain long hair 10 11 12 13 14 15 16 Use Safety Glasses Also use safety footwear snug fitting clothing protective gloves hearing and head protection Carrying Saw Carry the chain saw by the front handle with the saw stopped finger off the switch the guide bar and saw chain to the rear Maintain Chain Saw With Care Inspect chain saw cords periodically and if damaged have repaired by authorized service faci
20. when tested on a representative sample of chain saws Normal Cutting Position Those positions assumed in performing the bucking and felling cuts Notching Undercut A notch cut in a tree that directs the tree s fall Oiler Control A system for oiling the guide bar and saw chain Rear Handle The support handle located at or toward the rear of the saw Reduced Kickback Guide Bar A guide bar which has been demonstrated to reduce kickback significantly Replacement Saw Chain A chain that complies with the kickback performance requirements of ANSI B175 1 when tested with specific chain saws It may not meet the ANSI performance requirements when used with other saws Saw Chain A loop of chain having cutting teeth that cut the wood and that is driven by the motor and is supported by the guide bar Spiked Bumper Spike The pointed tooth or teeth for use when felling or bucking to pivot the saw and maintain position while sawing Switch A device that when operated will complete or interrupt an electrical power circuit to the motor of the chain saw Lock Off Button A movable stop that prevents the unintentional operation of the switch until manually actuated Installing saw chain and guide bar CAUTION Always be sure that the tool is switched off and unplugged before installing saw chain and guide bar Use the socket wrench to loosen the hex bolt holding the chain cover Remove the chain cover C
Download Pdf Manuals
Related Search