Magnadyne EAX540 User's Manual
Contents
1. e Affix the unit to the floor by pressing in place e Using a knife cut X s in the carpet e Once more use the hexagonal nuts directly above the brackets B bolts to attach the changer on top of the Ro carpet e Return the carpet to its original position allowing the bolts to stick through 10 Procedure for Installation Suspended Position e Confirm that the built in anti vibration boards on both the left 7 Built in anti vibration e o and right sides are set to the _ i de horizontal installation position 0 e Attach the left and right brackets A using the hexagonal bolt M4 x 5 e Determine the mounting location e Attach the CD changer with the and drill four mounting holes tapping screws M5 x 12 3 60 11 HANDLING THE DISCS Dirt dust scratches and warpage cause sound skips during playback and a deterioration of sound quality How to take care of your disc 1 Use compact discs that have the mark shown on the right COMPACT DIGITAL AUDIO 2 Fingerprints and dust should be carefully wiped off the disc s signal surface glossy side with a soft cloth Unlike conventional records the compact disc has no grooves to collect dust and microscopic debris so gently wipe with a soft cloth should remove most particles Wipe in a straight motion from the inside to the outside of the disc Small dust particles or light stains will have absolutely2. MAGNADYNE Installation and Operations Manual 70 ym R DISC COMPACT DISC AUTO CHANGER EAX540 COMPACT DISC AUTO CHANGER U S Patent No D486 815 CONTENTS HINTS FOR CORRECT AND SAFE OPERATION nee eee eeeceeeeneeneeeneee 2 HOW TO USE THE MAGAZINE on 3 PRECAUTIONS FOR HANDLING DISCS 4 INSTALLATION PARTS oiriin e ete oa i Maene a b e eai e 5 WIRING cee ee a r a cee 5 RESET FUNCTION oaaaaaaaaa00000000020222222 5 BEFORE INSTALLING THE UNIT 6 Transport LOCK SChOWS sesecst oe dee Ae ee en lea alee dees 6 e Installation and Wiring Precautions e esses esses sess eseeeeeeeeecee se ceeseeeseeeneeeteeeeeeeeeeaeeee 6 e Position of the built in anti vibration Board a 7 INSTALLATION etch tees ice ees een ee 8 e Procedure for Installation on Carpet Horizontal Position 8 e Procedure for Installation on Carpet Vertical Position 2 9 e Procedure for Installation on Carpet At a 45 angle ss 1515r1111111111 1 15 10 e Procedure for Installation Suspended Position HANDLING THE DISCS iunis edan TROUBLE SHOOTING scsassssiessnrete a nent iiei teen EEEE a R RE E HINTS FOR CORRECT AND SAFE OPERATION This CD Changer is designed to be operated only on 12 volt DC negative ground systems The unit cannot be used on 24 volt or positive ground systems The unit may not oper
3. on bottom of unit and then use Install board in proper direction Refer to installation in Operating Instructions 12 EAX540 UM 6 29 07
4. 2 M4 x 5 x2 x2 x4 x4 Tapping Screw DIN 8 Seal Double M5 x 12 Pin Cable Sided Tape a O Som aay OF CH o2 x1 x2 Connect this cable to the terminal of the CD player The reset button must be activated with either a ball point pen or thin metal object It is to be activated for the following reason e Initial installation of the unit when all wiring is completed e Some functions do not operate Reset button BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is locked into place during shipment by the transport screws Be sure to remove the screws prior to installation Caution After removing the transport lock screws place the supplied seals over the screw holes These seals are used to keep dust which could cause a malfunction out of the unit Installation and Wiring Precautions 1 To prevent a short circuit e Be sure to turn off the ignition and remove the negative battery cable prior to installation Note If the changer is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution to avoid causing a short circuit during installation 2 Do not install the unit in the following locations e Locations exposed to direct sunlight e Where hot air is discharged from the car heater e When proper
5. ate correctly in extremely hot or cold temperatures The unit is equipped with a built in self protection circuit When the temperature reaches a preset level the protection circuit halts all unit operations If this should happen open a window and allow the car to cool Condensation Moisture can condense on the laser lens of the CD changer during rainy and humid days or right after the heater is turned on in the car If this should happen the unit will not operate correctly To remedy the situation remove the magazine from the unit and wait approximately one hour During this time the moisture will evaporate and the unit will operate normally Remove the magazine from the unit when it is not being used during hot weather and the CD changer is not used for long periods of time HOW TO USE THE MAGAZINE i Loading a disc 1 Pick the tab on the magazine s disc tray and pull out only of the trays 2 Place the disc on the tray with its play surface facing down label surface facing up e Each tray can accommodate only one disc 3 Press the tab on the disc tray to store the tray back in the magazine e Up to ten discs can be loaded H Installing the magazine 1 Slide the door toward the right 2 First check that the magazine with the discs has its top side facing up and it is pointed in the right direction for installation Push it in until clicks into place indicating that it is now locked e When the magazine is used
6. e hexagonal bolt M4 x 5 Attach the left and right brackets A to their respective brackets B using the hexagonal bolts M6 x 12 and the hexagonal nuts M6 Hexagonal s bolts M4 x 5 Pull back the carpet and determine e Remove the hexagonal nuts and where to attach the unit take off the changer Stick the supplied double sided tape to the bottom of the brackets B and peel off the paper backing Affix the unit to the floor by pressing in place Using a knife cut X s in the carpet e Once more use the hexagonal nuts directly above the brackets B bolts to attach the changer on top of the carpet Return the carpet to its original position allowing the bolts to stick through Procedure for Installation on Carpet at a 45 angle e Set the built in anti vibration boards on both the left and right sides to gt Built in anti vibration the 45 installation position 45 bg J board position e Attach the left and right brackets A using the hexagonal bolt M4 x 5 e Attach the left and right brackets A to their respective brackets B using the hexagonal bolts M6 x 12 and the hexagonal nuts M6 Al Hexagonal bolts M4 x 5 e Pull back the carpet and determine e Remove the hexagonal nuts and where to attach the unit take off the changer e Stick the supplied double sided tape to the bottom of the brackets B and peel off the paper backing
7. for the first time it will not lock into place unless the power supply has been connected e Ejecting the magazine The magazine is ejected by pressing the eject button 4 Notes Be absolutely sure to close the door after having inserted or ejected the magazine Dust or dirt finding its way inside may cause malfunctioning of the unit Eject button PRECAUTIONS FOR HANDLING DISCS E With new discs The symptoms described below sometimes occur when new discs 7 are used e The disc is not played even Sasa when it is loaded E S gt Burrs e Operation changes to the next l disc before the first disc has a Burrs hole f chance to be played n e The same disc is played over and over again e The designated disc is not played Outside ciremference A Remove all plastic particles of burr from surfaces of disc before loading in magazine These symptoms occur when there are burrs on the center hole or outside circumference of the disc and as a result the disc has not been loaded properly or the disc catches on something inside the magazine In cases like these remove the burrs using a ball point pen or similar implement as shown in the figure on the right WARNING E Although protective film is being marketed as CD accessories use of these products will result in malfunctions and should absolutely be avoided INSTALLATION PARTS Bracket A Bracket B Hexagonal Bolt Truss Screw M6 x 1
8. gle The built in anti vibration board should be set to position 45 S INSTALLATION Procedure for Installation on Carpet Horizontal Position e Confirm that the built in anti vibration boards on both the left 7 Built in anti vibration and right sides are set to the ae board position horizontal installation position 0 Hexagon bolts M6 x 12 Attach the left and right brackets A X using the hexagonal bolt M4 x 5 Attach the left and right brackets A to their respective brackets B using the hexagonal bolts M6 x 12 and the hexagonal nuts M6 Pull back the carpet and determine e Remove the hexagonal nuts and where to attach the unit take off the changer Stick the supplied double sided tape to the bottom of the brackets B and peel off the paper backing Affix the unit to the floor by pressing in place Using a knife cut X s in the carpet e Once more use the hexagonal nuts directly above the brackets B bolts to attach the changer on top of the carpet Return the carpet to its original position allowing the bolts to stick through Procedure for Installation on Carpet Vertical Position e Set that the built in anti vibration boards on both the left and right wt Built in anti vibration sides are set to the vertical gt board position installation position 90 J Hexagon bolts M6 x 12 Attach the left and right brackets A using th
9. installation is not possible and where a great deal of vibration is generated 3 e Be sure to use the supplied brackets and screws e When installing the unit do not use any screws that are part of the brake or steering system 4 This unit cannot be installed in any way except that which is authorized on its side on its end at a 45 angle or suspended Installing it with its side facing down upside down can cause malfunctioning Position of the built in anti vibration board This unit can be installed horizontally suspended vertically and at a 45 angle Once the installation position has been decided it s necessary to set the position of the built in anti vibration board inside the unit Please do this before performing the procedure listed below Vibration may cause the disc to skip if the unit is used before properly setting the anti vibration board e At the time of shipping the built in anti vibration board is set for horizontal installation e There are built in anti vibration boards on both the left and right sides e Set the anti vibration board position with a screwdriver before attaching the brackets For use when unit is installed horizontally or suspended Confirm that the built in anti vibration board is set to position 0 ra For use when unit is installed vertically E The built in anti vibration board should be set to position 90 amp For use when unit is installed at a 45 an
10. no effect on reproduction quality 3 Never use such chemicals as record sprays antistatic sprays or fluid benzene or thinner to clean compact discs Such chemicals would irreparably damage the disc s plastic surface 4 Discs should be put back in their cases after to avoid serious scratches that could cause sound skip 5 Do not expose discs to direct sunlight high humidity or high temperatures for extended periods of time Long exposure to high temperatures can warp the disc 6 Do not stick paper or write anything with a ball point pen on the disc surface TROUBLESHOOTING An error made in operation or in the connections is sometimes mistaken for a failure or breakdown Perform the checks described in the following table before calling in the servicing engineer Symptom No power Cause Improper connection Remedy Check connections Magazine cannot be installed Direction in which it is inserted is wrong Insert it in proper direction CD is not played Disc has been loaded upside down Load disc with play side facing up Noise is heard during playback or sound is intermittent Large scratches on disc or warped disc Extremely dirty disc Transit screws still in place Built in anti vibration board is installed in wrong direction Compare sound with another disc If sound from second disc is acceptable first disc is defective Clean disc Remove screws x 3
Download Pdf Manuals
Related Search