Macsense Connectivity MPC-200 User's Manual
Contents
1. Ether Card Then the FastEther Card will eject automatically Specification Appendix A Specifications Network standard 10Mbps IEEE 802 3 10BASE T Ethernet 100Mbps IEEE 802 3u 100BASE TX Fast Ethernet Type II PCMCIA Hot Plug and Play Fast Ethernet CardBus Card supports Full Duplex 10BASE T and 100BASE TX communication Complies with 32 bit PCI Card Bus specification For Windows 3 x and Windows 95 Windows 98 and Windows NT operation sys tem Support for Network and Communication Device Class OnNow requirements for Microsoft PC97 and PC98 specification including all wake up events Pattern matching with VLAN support Link change Magic Packet with SecureON Supports RJ 45 STP 1 UTP 3 4 5 media connectivity Supports the legacy mode including sleep snooze normal and CLKRUN Contains on chip PCS and scrambler de scrambler for 100BASE TX Fully compliant with ANSI 8802 3 and 10BASE T Support IEEE 802 3 auto negotiation algorithm of full duplex and half duplex opera tion for 10Mbps and 100Mbps NWAY Automatically negotiates 10Mbps or 100Mbps connection speed Integrated large transmit and receive FIFOs provide packet buffering for longer latency Integrated an on chip DMA with programmable burst size providing low CPU uti lization Provides 3 3 volt lower power CMOS design devices design LEDs for diagnostics and monitoring use Assignment Appendix B Pin A2. User s Manual Fast Ethernet CardBus MPC 200 2 lt Aacsense Table of Contents Chapter 1 Introduction 0 00 c kk KK KK KK KK kk kk kk kk kk 1 all ci ate dentes _ np 1 Network Interface 4 kk kk kk kk kk KK ee 1 Driver Support ius e gom Gee al a h k e EORR le J l a exon an laya e 1 Physical characteristics x xa llle 1 Installing the Fast Ethernet CardBus Card kk RR 2 Chapter 2 Getting Started kk kK KK KK eee 3 Installing the Fast Ethernet CardBus Card 44 3 LED Indicators isi kk xi kk RR he oe eee al eee es 4 Readme tile ia ee k RE eng aah eka kl d AU Ed 4 Chapter 3 Driver Installation for Mac OS 5 System Requirements 000 KK KK KK KK ee 5 Installation dE et k kk Kala Ry Rx ES ee eed Sibi 5 Software Installing xan 000 cc WA le eee 5 AppleTalk Setup W kk kk kk kK KK KK KK KK KK KK KK KK IK KK KK ke 6 TCP IP Setup ias e dili k dans E d ew X WW da Ah ce di a 7 Ejecting the Fast Ethernet CardBus Card 0005 7 Appendix A Specification kk kk kk kk KK KK RR KK kk kk kk 9 Appendix B Assignment 000000 cee kk kk kK kK kK kk kk kk kk kk 11 RJ 45 Connector 0 0 kk kk KK KI KK eee 11 Introduction Chapter 1 Introduction This manual describes how to operate the Fast Ethernet CardBus Card The Fast Et
3. etwork Interface RJ 45 to connect with 10BASE T hub 100BASE TX Hub or Switch Hub Physical Characteristics Standard Conformance IEEE 802 3 for 10BASE T IEEE 802 3u for 100BASE TX Host Interface PC Card 95 CardBus Standard Ethernet Data Speed 10Mbps and 100Mbps Auto Negotiation Introduction Bus Width 32 bits Power 3 3 V Temperature 0 C 60 C 32 F 140 F Std Operating Humidity 10 to 90 Distance 100m from Hub to Node Dimensions 86mm x 54mm x 5 mm Installing the Fast Ethernet CardBus Card You will be installing the Fast Ethernet CardBus Card in your computer If you are having trouble locating the slot refer to the user s manual of your computer or consult the manufacture of your computer Gently slide the PC Card into the CardBus PC Card slot Make sure the Card is firmly seated in the socket and you are ready to setup and install the network drivers For a connection to a Fast Ethernet network use a Category 5 unshielded twisted pair UTP 5 or Category 1 shielded twisted pair STP 1 cable with a RJ 45 connector to connect with a 100Mbps port of hub or switch For a connection to a 10BASE T Ethernet network use a Category 3 4 or 5 UTP or STP 1 cable with a RJ 45 connector to connect with a 10Mbps port of a hub or switch Getting Started Chapter 2 Getting Started Installing the Fast Ethernet CardBus Card You will be installing the Fast Ethernet CardBus Card in CardBus s
4. hernet LAN PC Card is a Credit card sized Ethernet Card which works with any comput er notebook sub notebook or Macintosh PowerBook G3 series or Card Reader that sup ports CardBus slots CardBus is a function and performance extension of the PC Card PCMCIA stan dards The CardBus interface is a 32 bit wide and Bus mastering allowable device It enhanced the overall system throughput This Fast Ethernet CardBus Card could be connected to either 100Mbps Fast Ethernet or 10Mbps Ethernet network For operating in a 100Mbps 100BASE TX Fast Ethernet network a Category 5 unshielded twisted pair UTP cable or Category 1 shielded twisted pair STP cable should be used For operating in a 10Mbps 10BASE T Ethernet network a Category 3 4 or 5 UTP cable or Category 1 shielded twisted pair STP cable could be used Features CardBus form factor for CardBus equipped portable PCs IEEE 802 3 for 10BASE T and IEEE 802 3u for 100BASE TX compliant Automatically negotiates 10Mbps or 100Mbps connection speeds depending on speed of the network Provides full duplex to enhance throughput Offers high performance 100Mbps networking via 32 bit PCI CardBus slot Complies to PC Card 1995 CardBus standards Switch less design and software configurarble card setting 68 pin connector for attachment to PC s CardBus slot and 15 pin flat connector to media coupler 3 3V low power consumption LEDs monitoring indicators N
5. ise this documentation and to make changes in content sometimes without obligation among Macsense Connectivity Inc to provide notification of such revision or change FCC Warning This equipment has been tested and found to comply with the limits for a Class B digi tal device pursuant to Part 15 of the FCC Rules These limits are designed to provide rea sonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no promise that interference will not happen in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by any of the following measures Reorient or move the receiving antenna Increase the distance between the equipment and receiver Connect the equipment into an outlet on a circuit different from the one which the receiver is connected to Consult the dealer or an experienced radio TV technician for help You may use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections CE Declaration of Conformance This equipment complies with the requirements relating to electromagnetic compatibili
6. lot of your computer If you have trouble locating the slot please refer to your computer s user manual or consult the dealer of your computer Follow the procedure below to install the Fast Ethernet CardBus Card 1 Turn off the host computer 2 With the card s 68 pin connector facing the PCMCIA CardBus slot gently slide the PC Card into the CardBus slot Make sure the card is firmly seated in the socket 3 Plug the Ethernet adapter cable to the 15 pin connector on the Fast Ethernet CardBus Card as in the following figure below SP 4 Connect your Ethernet adapter cable to the network using a RJ 45 cable 5 Power on your notebook computer 6 Now you are ready to install your communication software as described in the following chapters Getting Started LED Indicators RJ 45 Female Connector Link Act LED 100 LED This LED is used to indicate the Ethernet speed The green light indicates a connection with a 100BASE TX Fast Ethernet network Link Act LED This LED is used to indicate the network activity It is blinking when the PC Card is transmitting or receiving packets from network It is also lit when indicating a Link to a network README There is one file named Readme on driver diskette which provides the information about this Driver Diskette s contents and installation guide This file is located in the root director
7. s are available ee AppleTalk e El Connect via KRESAA Ea Infrared Port CIRTalk Modem Printer Port Current zone lt no zones available gt r Setup AppleTalk address gl User defined Node 127 Network 65280 Network range to 65534 2 mt Chapter 3 Driver Installation for Mac OS Close the control panel when you have finished To confirm the change of network connections click OK TCP IP Setup Open the TCP IP control panel TCP IP Select FastEther Card from the pop up menu AppleTalk MacIP Ethernet built in Connect via EEUU r Setup Configure Manuall IP Address Subnet mask 255 255 255 0 Router address 172 16 1 254 Name server addr 168 95 192 1 140 111 1 2 139 175 55 244 140 115 1 21 139 175 10 20 Search domains hntp1 hinet net Set up TCP IP configuration according to the situation of your network environment Close the control panel when you have finished To confirm the change of network connections click OK Ejecting the FastEther Card Open the AppleTalk control panel Select an AppleTalk connection other than FastEther Card e g IRTalk LocalTalk Printer Port or Modem Port Close the control panel and wait for a few seconds Chapter 3 Driver Installation for Mac OS Drag the FastEther Card icon that appears on the desktop to the Trash N Fast
8. ssignment RJ 45 connector The RJ 45 connector is used to connect with a hub or switch RJ 45 regular ports can be attached to any devices which use a standard network interface e g a workstation server bridge or router RJ 45 up link ports can be cascaded to a station port on similar networking devices e g another switch or hub Use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections 100Q Category 3 4 or 5 cable for 10 Mbps connections or 100Q Category 5 cable for 100 Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Regular Port Up Link Port Input Receive Data Output Transmit Data Input Receive Data Output Transmit Data Output Transmit Data Input Receive Data Output Transmit Data Input Receive Data asno Reseve Reserve TM eee Pin 8 Pin 1 Schematics for straight cable are shown as below Straight Through Crossover Switch or Hub End Node Switch or Hub Switch or Hub 1 IRD 1 OTD 2 IRD 2 OTD 3 OTD 3 IRD 4 OTD 4 IRD 11 Copyright Copyright 1998 by this company All right reserved No part of this documentation may be reproduced in any form or by any means or used to make any directive work such as translation or transformation without permission from Macsense Connectivity Inc Macsense Connectivity Inc reserves the right to rev
9. ty EN 55022 95 Class B This meets the essential protection requirements of the European Council Directive 89 336 EEC on the approximation of the laws of the Member Status relating to electromagnetic compatibility You are now cautioned that changes or changes not expressly approved by the party responsible for compliance could void your authority to operate the equipment Trademarks All companies brands and product names are trademarks or registered trademarks of their respective companies Specifications are the subject to be changed without prior notice 12
10. y of the diskette Chapter 3 Driver Installation for Mac OS Chapter 3 Driver Installation for Mac OS System Requirements Mac OS version 8 1 or above Macintosh G3 PowerBook Series Card and Socket Service 3 0 Open Transport 1 3 or above Installation Before your computer system can recognize your Fast Ethernet CardBus Card it is necessary to run some software to enable it This section gives a brief overview of the installation process Software Installation 1 Make sure that the system extensions are left on before installing the driver 2 Insert the FastEther CardBus driver diskette into the floppy drive FastEther Card Installer ES Oo 2 items 646 4 MB available B FastEther Card Installer 3 Double click the Installer icon The Easy Install dialog box then appears Chapter 3 Driver Installation for Mac OS 4 Click the Install button The Installer will install the appropriate driver to your com puter FastEther Card Installer B Click the Install button to install FastEther Card v2 0 Extensions on the boot disk r Install Location G3PB 0S v m on the disk G3PB 0S 5 Click the Restart button when installation is completed AppleTalk Setup Open the AppleTalk control panel SS AppleTalk Select FastEther Card from the pop up menu Optional The Current Zone pop up menu will be active if zone
Download Pdf Manuals
Related Search