Mace CAM91 User's Manual
Contents
1. Video Out Jack Used to connect an external video a monitor in jack Auto Iris Lens Plug L Wrench REMOTE Jack Menu Setup Buttons Power Terminal C Mount Adaptor Instruction Manual Set Button Used to connect AC24V Used to access menu mode or DC12V power source Also used to confirm the setting Non Polarity Up Down Button Used to choose the desired menu item It also moves the cursor up or down in the menu screen LEFT RIGHT Button Used to change the parameter of the selected menu item It also moves the cursor to the left or right in the menu screen Day amp Night Color CCD Camera 12 13 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 14 E Installation Method Lens The lens is not supplied with this camera Purchase a lens suitable for your environment This camera accepts the auto iris lens and both C and CS mount lens Installing Auto Iris Lens 1 Remove the cover from the iris lens plug supplied and solder the lens cable to the plug as shown below Pin No Video type DC type No 1 Pin Power Red Damping No 2 Pin N C Damping No 3 Pin Video signal White Drive No 4 Pin GND Black Lens cable 2 Attach the lens to the camera by turning clockwise Day amp Night Color CCD Camera 4 E Installation Method 3 Connect the lens plug to the auto iris connector on the right side of the camera 4 Set the DC VIDEO selection switch to2. CAM91 2005 10 13 10 45 PM 4 38 m Troubleshooting m Warranty If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician MACE Security Product Warranty Problem Solution The aoe eat gt Check that you have properly connected the camera to an appropriate power source Mace will repair or replace without charge any merchandise proved working properly defective in material or workmanship for a period of one year after the date gt Check that the power cord and line connection between the camera and monitor are of shipment Nothing appears fixed properly on the screen gt Check that the DC VIDEO selection switch on the rear of the camera is set to a proper Exceptions to this warranty are as noted below position according to the type of your auto iris lens Mace will warrant all replacement parts and repairs for 90 days from the date of Mace shipment All goods requiring warranty repair shall be sent freight gt Check that you have set to proper iris level in the setup menu when you use the DC prepaid to Mace Fort Lauderdale Repairs made necessary by reason of The image on the auto iris lens misuse alteration normal wear or accident are not covered under this screen is dark gt Check that you have set to proper brightness level in the ESC mode when you use the warranty Manual iris lens Tor
3. m Operating Your Camera O Color Day amp Night Your camera provides automatic mode changeover by sensing day or night conditions It changes to Color mode in day conditions for optimal color and to B W mode in night conditions for clear identification 1 Press the SET button to display the setup menu and move the arrow indicator to Color using the UP or DOWN button Setup Camera ID BLC Lens Shutter Gain White Balance Motion Detect Color Select the AUTO ON BW EXT Sync using the LEFT or RIGHT button Reset End 2 Select a mode using the LEFT or RIGHT button e ON Color mode is kept up B W Black and white mode is kept up AUTO The mode is changed between Color and B W automatically depending on the brightness Pushing the SET button at Auto mode you can control the mode changing point and time and burst existence during the mode change to B W mode 31 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 32 m Operating Your Camera Color B W Change p gt Color B W Point 3 Color B W Time 5 mm m m m m m B W_ Color Time 10 ee m m BURST OFF Press SET to Return Color B W Point 1 5 1 around 1 LUX 3 around 3 4 LUX 5 around 7 8 LUX Change the value using the LEFT or RIGHT button 1 5 Change the value using the LEFT or RIGHT button 1 10 Change the value using the LEFT or RIGHT button 2 20 X The color chang
4. occurred hunting DC12V power is non polarity Day amp Night Color CCD Camera 6 ID Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 18 b m Operating Your Camera m Operating Your Camera Configuration of The Menu Setting Up The Menu Use the five Setup Menu buttons on rear of the camera Setup Menu _____ Camera ID yp OFF ON BLC OFF ON i LEFT RIGHT SET m Lens DC VIDEO Manual DOWN gt Shutter 1 Press the SET button to access the Setup mode over 1sec ESC OFF FLKless Manual Setup menu is displayed on the monitor screen Gain AGC OFF Select the gt Select the condition with gt White Balanco gt e ATW AWC Manual button Shutter Motion Detect eae OFF ON Motion Detect gt Color Day amp Night Sa AUTO ON BW EXT Reset gt Sync End INT L L 2 Select the desired feature using the UP or DOWN button gt Reset Each time you press the UP or DOWN button the arrow indicator moves up or down gt End Move the arrow indicator to the desired feature item 3 Change the status of the selected feature using the LEFT or RIGHT button 4 When completed move the arrow indicator to End and press the SET button x For the mode with you can access submenu Day amp Night Color CCD Camera 18 19 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 20 p m Operating Your Camera m Operating Your Camera o Cam
5. Reset En ses sis cise siete 0 6 sis ore aisisie aca saan siisi seserinis External Connecting Terminal 24 26 27 29 31 33 34 3 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 10 p m Name and Function of Each Part m Name and Function of Each Part Front Bottom C Mount Adaptor Attach the C Mount Adapter when using the C Mount Lens Tripod Mounting Hole Used to install the camera on an optional tripod The tripod must be equipped with the screw specified as below e 1 4 20UNC 20 THREAD e L 4 5mm 0 2mm SO standard or 0 197 ASA standard Tripod Mounting Bracket Screw Hole Used to fix the Tripod mounting Bracket on the top of the camera Auto Iris Lens Connector Used to connect the auto iris lens plug You can remove and install this bracket on the top of the camera You must use the supplied screw or equivalent within 4mm If not the bracket may not be fixed properly Day amp Night Color CCD Camera 10 1 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 12 p Name and Function of Each Part Name and Function of Each Part The LED turns on when power is supplied DC VIDEO Selection Switch Used to choose DC or VIDEO according to the type of your auto iris lens Back Power LED Accessories External Terminal E Used to connect external Day Night input signal eo 2 This also provides the motion detect signal gt as
6. DC or VIDEO according to the type of the lens LENS DC VIDEO REMOTE OOO fe lt SET BED Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 16 p E Installation Method E Installation Method Installing C CS Mount Lens Connecting to Monitor Before mounting a lens please check whether it is a C mount or CS Mount lens Connect the VIDEO Out jack to the monitor VIDEO in jack The back focus is set for the CS mount lens at the factory Mounting a CS Mount Lens l After removing the protecting cap attach the lens into the camera by turning Monitor clockwise Connect the power plug to a normal grounded AC DC outlet Use AC 24V 300mA or DC 12V 500mA power source Mounting a C Mount Lens Gonnacting to Power 1 Attach the C Mount lens adaptor by turning clockwise 2 Attach the lens to the camera by turning clockwise AG 24V IN DG 12V IN Be sure to connect power only after all the installation is complete A heavy lens may disturb the balance with the camera and possibly result in damage e Note that power adaptor is not supplied with camera Don t use lens heavier than 450g e Use the UL listed class 2 power transformer of AC 24V adaptor e It is recommended to set the lens ALC mode to Av mode Average Pk mode can be Ground should be connected to the FGND terminal
7. close to a gas or oil leak It may result in fire or other hazards Line Lock Selectable You can select the Sync system on OSD BLC Function When the image is in front of strong background lighting your camera allows you to get the clear image Day amp Night Color CCD Camera A 5 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 6 m Precautions Do not install the camera in extreme temperature conditions Only use the camera under conditions where temperatures are between 10 and 50 Be especially careful to provide ventilation when operating under high temperatures Do not install the camera under unstable lighting conditions Do not drop the camera or subject them to physical shocks It can cause malfunctions to occur Never keep the camera face to strong light directly Severe lighting change or flicker can cause the camera to work improperly Day amp Night Color CCD Camera 6 It can damage the CCD Do not touch the front lens of Do not expose the camera to the camera rain or spill beverage on it e 2 If it gets wet wipe it dry immediately Liquids can contain minerals that corrode the electronic components It is one of the most important parts of the camera Be careful not to be stained by fingerprint Ly Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 8 m Contents Name and Function of Each Part e FONE ctsev tebe Pde tueel cided hine
8. CAM91 2005 10 13 10 45 PM 4 1 MACE Electronic Surveillance Products 3233 SW 2nd Ave Fort Landerdale FL 33315 USA toll free 877 585 MACE local 954 585 6223 fax 954 585 6225 www mace com mace 1 3 Day amp Night Color CCD Camera Model CAM91 Instruction Guide MACE Electronic Surveillance Products CAM91 2005 10 13 10 45 PM 4 3 p m Warning e TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE m Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL m Explanation of graphical symbols AN AN The lightning flash with arrowhead symbo within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of e The exclamation point within an equilatera ectric shock to persons triangle is intended to alert the user to the presence of important operating and maintenance servicing instruction in the li the product terature accompanying 3 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 4 p m Features m Warning Day amp Night 1 The camera needs periodic inspection The camera provides automa
9. D Camera S22 m Operating Your Camera o Lens Selection You can set the type of the lens and control the brightness of the screen 1 Press the SET button to display the setup menu and move the arrow indicator to Lens using the UP or DOWN button Setup Camera ID BLC Lens Select the DC Video or Manual using Shutter the LEFT or RIGHT button Gain White Balance Motion Detect Color Syne Reset End 2 When the auto iris lens is mounted you have to set the DC Video selection switch on the back side of the camera The setup window displays DC or Video according to status of this selection switch LENS DC VIDEO 3 If you select DC mode you can adjust the desired brightness For a stable performance the level 10 is recommended Tris Level 10 Select the level using the LEFT or m m m RIGHT button 0 30 Press SET to Return 23 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 24 m Operating Your Camera O Shutter Speed Control You can control brightness of the screen by the shutter speed You can select the automatic control and OFF 1 60 or 1 50sec fixed mode Flickerless and manual control of the shutter 1 Press the SET button to display the setup menu and move the arrow indicator to Shutter using the UP or DOWN button Setup Camera ID BLC Lens Shutter Select Shutter to the desired mode Gain like ESC OFF FLKless or Manual White Balan
10. Output Resolution 480 Color 520 BWJTV Lines Horizontally Shutter Speed 1 60 1 10 000sec 50 1 10 000sec S N Ratio More than 48dB AGC OFF Video Output 1 0 Vp p NTSC composite 1 0 Vp p PAL composite 3 tas 0 5Lux at F1 2 Color Min Illumination 0 03Lux at F1 2 8 W Sync System Internal Line Lock selectable 1 DN Input Terminal over Pull up input of DC 5V 0 2mA Back Light ON OFF selectable Open contact Color mode Iris Mode DC lris Video Iris ESC selectable Closed contact B W mode White Balance ATW AWC MANUAL selectable 2 Motion Detect Output Signal Level Lens Mount CS mount or C mount with the supplied adaptor At POSI Positive mode 4 0V 5 0V Color AUTO ON BW EXT selectable Motion appeared ov 2 5 0 5sec M gt OSD Built in No motion appeared a gt RS 232C comm Available At NEGA Negative mode Power Supply AC 24V 60Hz DC 12V Non polarity AC 24V 50Hz DC 12V Non polarity 4 0V 5 0V __ _ _ _ _ Power Ci No motion appeared Motion appeared ower Consumption MAX 3 0watt 2 5 0 5sec OV Operating Temperature 10 C 50 C j l Operating Humidity 90 RH Max At ALARM You can connect an extra an equipment like lamp or buzzer on Sr 7 Dimension 62 W gt 52 H gt lt 133 L mm Without Lens the external of camera The output is an open collector under DC 16V 100mA OFF Open ON under 100mA Day amp Night Color CCD Camera 36 31 Day amp Night Color CCD Camera
11. VIDEO selection switch on the rear of the camera is set to a proper position according to the type of your auto iris lens 1 Model and serial number 2 Date of shipment P O number Sales Order number or Mace invoice p gt Check that the power frequency is proper in Sync If the power frequency is not proper the linelock synchronization mode cannot be used The image on the Set the Sync mode to INT mode scrani distorted NTSC Model s power frequency in LL mode 60Hz PAL Model s power frequency in LL mode 50Hz number 3 Details of the defect or problem Day amp Night Color CCD Camera 38 33 Day amp Night Color CCD Camera
12. an increment of 1 Move the arrow indicator to Top using the UP or DOWN button and increase or decrease the value using the LEFT or RIGHT button Repeat the procedure for bottom left and right 3 Adjust Sensitivity e Move the arrow indicator to Sensitivity using the UP or DOWN button then press the LEFT or RIGHT button to decrease or increase the value f you decrease the sensitivity the camera will detect only motion that is clearly noticeable If you want to set the camera to detect minor motion increase the sensitivity e You can select the sensitivity from 0 to 15 Higher sensitivity detects smaller motions at the risk of false detection Therefore zone adjustment is recommended rather than sensitivity adjustment 4 Adjust the output signal e POS Positive When a motion is sensed 5V of Pulse will be output e NEGA Negative When a motion is sensed OV of Pulse will be output ALARM You can connect external equipment like buzzer or lamp The output of alarm is an open collector under DC16V amp 100mA capacity x Tips on using Motion Detection e After selecting zone and sensitivity perform a test operation to make sure it works properly e f the lighting flickers the motion detection feature might not work properly e This system does not guarantee prevention of fires or thefts The manufacturer is not responsible for any accident or damage Day amp Night Color CCD Camera X30 p
13. ce using the LEFT or RIGHT button Motion Detect Color Syne Reset En 2 ESC selected e The electronic shutter can be automatically controlled from 1 60 1 50 to 1 10 000sec e The brightness can be controlled e If Auto Iris Lens is mounted and adjusted ESC mode cannot be selected 3 OFF selected e The shutter speed is fixed at 1 60 1 50 sec 4 FLKless selected e The speed is fixed at 1 100sec in NTSC mode and at 1 120sec in PAL mode This should be selected when flickering is caused by discord of environmental lighting and frequency Day amp Night Color CCD Camera 24 m Operating Your Camera 5 Manual e You can select speed from 1 60 to 1 10 000sec NTSC mode 1 50 to 1 10 000sec PAL mode Shutter 1 250 Change the range using the LEFT or RIGHT button 1 60 1 50 1 10 000 Press SET to Return When the shutter speed is increased or decreased using the LEFT or RIGHT button you can find the difference by monitoring the brightness of the screen 25 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 26 e m Operating Your Camera m Operating Your Camera o White Balance Control You can use this when the screen color needs to be controlled 1 Press the SET button to display Setup menu and move the arrow indicator to White Balance using the UP or DOWN button o Gain Control You can see a brighter picture at low light level Increasing the gain level you will see the noise
14. cter correct the character by using abcdefghijklm i he 4 directional buttons nopqrstuvwxyz i 5 Select the position at which the camera ID will be located on the screen 0123456789 Move the cursor to Pos and press SET button ind Clr Pos 2 The camera ID is displayed on the top left of the monitor screen Default position 3 Select the position by using the 4 directional buttons then press the SET button to confirm the position 6 When completed move the cursor to End and press SET button Day amp Night Color CCD Camera 20 2n Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 22 m Operating Your Camera o Back Light Compensation BLC When the image is in front of strong background lighting that will be presented dark on the monitor If you select this function you can get the clear image 1 Press the SET button to display the setup menu and move the arrow indicator to BLC using the UP or DOWN button Setup Camera ID BLC Select ON using the LEFT or Lens RIGHT button Shutter Gain White Balance Motion Detect Color Syne Reset End 2 When BLC selected to ON press the SET button You can control the level of weight Weight Select the weight number 0 4 using the LEFT or RIGHT button Press SET to Return x As the weight level is high the BLC area is limited to the middle of the screen and the sensitivity gets rate Day amp Night Color CC
15. dnoads vide ween mein e BOOM wie ce delecdacgin sna urapa paaien a i E aE E E E NT e ACCESSOMES 2 0 06 dee dacd estes ddewa seuceee eed deweddocedeye Installation Method LANS sasacces Operating Your Camera e Configuration of The Menu ssecececeeeeeeeeteeeeeeere e Setting Up The Menu sececceceeeeceereeeeeteeeeeeeee Camera lD ice cbse ssce dati o e sii atte sareva tana ieee Vinings Back Light Compensation ssesececeeeeeecececeeeeeees ONS Selection seres csssnrnectiar teienei pin ai iina Day amp Night Color CCD Camera a nstalling Auto Iris Lens se eee cece cee ce cece cece eeeees nstalling C CS Mount Lens seseeececeeececeenceeeeees Mounting a CS Mount Lens s seeecececece cece ceeeeere Mounting a C Mount Lens ssesececececeeceeecneneees Connecting to Monitor secceceee eee erecee eens seees Connecting to Power seeee cece cease eee se cee ce cee enees a a a SAN ODO A gt 10 11 12 13 18 19 20 22 23 Using Remote Jack Specifications Troubleshooting Warranty Shutter Speed Control ss eee cece cee ce ener eee eeee cece Gain Control lt scs sr saieresias anid are abiaw dere Saree i Csata niiden White Balance Control cece cece eee ce cee ee cece eees Motion Detection sei sists csreaics cas ears caaiscnesnuaienss seers lt ColOnDaySinighit essei se selds nee sasennsenri ngesian Synchronization Mode ssssssssssesssessessssesesese
16. era ID 2 You can enter up to 15 characters If you enter a camera ID the name will be displayed in the screen monitor 1 Move the cursor to character enter location by 4 directional buttons 1 Press the SET button to display the setup menu and move the arrow indicator 2 Selected character blinks to Camera ID using the UP or DOWN button f ID Character Setup ABCDEFGHIJKLM Camera ID Select the status ON or OFF NOPQRSTUVWXYZ BLC using the LEFT or RIGHT abcdefghijklm Lens button If the camera ID feature nopqrstuvwxyz Shutter is set to OFF the name will not 0123456789 Gain be displayed in the monitor Clr Pos White Balance End Motion Detect Color ae 3 Press the SET button to confirm the blinking character The first character is esel End saved and the cursor in the bottom of the screen moves to the next position 4 Repeat steps 1 2 and 3 until you create the full name you want 3 If you make a mistake while entering name Press SET button ove the cursor to Clr press SET button After erasing the character correct he character again ID Character 4 To edit existing Camera ID move the cursor to or in the ID generation screen and press SET button After you choose or each time you press ABCDEFGHIJKLM he SET button the cursor moves to the left or right in the string of characters NOPQRSTUVWXYZ i When the cursor moves to the wrong chara
17. increased although the picture gets brighter 1 Press the SET button to display the setup menu and move the arrow indicator to Gain using the UP or DOWN button Setup Camera ID BLC Lens Shutter Gain Select AGC or OFF using the LEFT or White Balance RIGHT button Motion Detect Color Syne Reset End 2 You can control the Gain level at AGC selected Gain Limit Middle Low Middle High Press SET to Return x Caution When Gain Limit is set to Low screen noise will decrease but resolution decrease When Gain Limit is set to High resolution will increase but screen noise will increase Day amp Night Color CCD Camera 26_ Setup Camera ID BLC Lens Shutter Gain White Balance Motion Detect Color Syne Reset End Select ATW AWC or Manual using the LEFT or RIGHT button 2 The three white balance control modes are as follows TW Auto Trace White Balance The camera automatically controls the white balance in any environment WC Auto White Balance Control The white balance is automatically adjusted in a specific environment In order to obtain the best result press the SET button while the camera ocused on white paper If the environment including the light source is changed you have to adjust he white balance again 21 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 28 p m Operating Your Camera m Operating Your Camera Manual o Moti
18. ing point above is based on the AGC level to the middle You should select the proper value depending on the condition like lens e Color B W Time 1sec 10sec 1sec term B W Color Time 2sec 20sec 1sec term e BURST OFF ON EXT The Color BW mode change can be controlled by an external Sensor or other equipment connected on the DN terminal D N IN on the back side of camera Pressing the SET button at EXT mode you can control the burst existence during the mode changing to B W mode BURST OFF ON DN input terminal is pull up of DC 5V and over 0 2mA Open contact Color mode Closed contact B W mode 1 Under Gain OFF Color BW does not change over automatically ON OFF is only available 2 If you change Gain menu OFF to AGC Color mode change to AUTO automatically 3 Adjust the focus if the camera is out of focus for changing modes Day amp Night Color CCD Camera 32 m Operating Your Camera o Synchronization Mode Two synchronization modes are available internal and External linelock In linelock mode it synchronizes the video signal between cameras without a synchronous generator The linelock synchronization is only used in the areas of 60Hz NTSC models 50Hz PAL models 1 Press the SET button to display the setup menu and move the arrow indicator to Sync Using the UP or DOWN button Setup Camera ID BLC Lens Shutter Gain White Balance Motion Detect Color p g
19. menu Command O End Press the SET button to display the setup menu and move the arrow indicator to END using the UP or DOWN button Then you are finished on Setup Setup menu Command SET OA 02 01 00 00 AF UP OA 02 02 00 00 AF DOWN OA 02 03 00 00 AF LEFT OA 02 04 00 00 AF RIGHT OA 02 05 00 00 AF If there s no button control at Menu over 30 sec the setup is automatically finished with automatic update of the controlled menu by that time However there is no time limit at Subsidiary Menu Day amp Night Color CCD Camera s34 35 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 36 b m External Connecting Terminal m Specification Day Night External Signal Input Motion Detect Output ITEM NTSC PAL The Color BW mode change can be controlled by an external sensor or other Image Sensor 1 3 SONY SUPER HAD IT CCD equipment connected on the DN terminal Day amp Night on the back side of Picture Elements 811 H gt lt 508 V 795 H gt 596 V camera Optional Function Effective Pixels 768 H gt lt 494 V 752 H x 582 V When you use Motion Detection mode the appointed signal is output in every eee 2 4 Interlace NTSC Standard 2 4 Interlace PAL Standard time motion detected 525 Line 60Fields 30Frames 625 Line S50Fields 25Frames DIN Input GND Motion Detect
20. on Detection To fine adjust select the Manual mode You can increase or decrease the red Your camera transmits an alert signal when it detects motion of an object on the or blue factor while monitoring the difference on the screen Set to Manual screen If you connect the camera to an external alarm you can pay attention to mode and press the SET button the screen when the alarm sounds This feature is useful when you have to Increase or decrease the value for red R Gain and blue B Gain watching the monitor several screens simultaneously color of the picture and press the SET button when you obtain the best color 1 Press the SET button to display the setup menu and move the arrow indicator to Motion Detect using the UP or DOWN button Camera I BLC Red Change the range using the Lens Blue LEFT or RIGHT 20 20 Shutter Gain White Balance Motion Detect Select On using the Color LEFT or RIGHT button Syne Reset End Press SET to Return SET button pushed Motion Detection gt Top 4 Change the zone using the Bottom 9 LEFT or RIGHT button Left 3 Right 10 Zone area is displayed Sensitivity 8 mm m m m Output Type POSI Press SET to Return Day amp Night Color CCD Camera 28 2 Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 30 m Operating Your Camera 2 Specify the zone area e You can specify the zone area by setting a proper value from 0 to 15 with
21. onto Mace assumes no risk and shall be subject to no liability for damages or loss screen is dim gt Check if the lens is stained If dirty clean the lens with soft clean cloth resulting from the specific use or application made of the Products Mace s In the setup menu thak TE i ae liability for any claim whether based on breach of contract negligence Aio modaudss S no ou havo propery soe Me Gai seated ne setup ment serte infringement of any rights of any party or product liability relating to the not activate Teature to AGL Products shall not exceed the price paid by the Dealer to Mace for such Products In no event will Mace be liable for any special incidental or Fate a gt Check that you have properly set the White Balance feature under the setup menu consequential damages including loss of use loss of profit and claims of matched third parties however caused whether by the negligence of Mace or otherwise The contrast on gt Adjust the contrast feature of the monitor cori is too gt If the camera is exposed to too strong light change the camera position fa warranty repair is required the Dealer must contact Mace at 877 585 gt Is the camera facing to direct sunlight or fluorescent lighting 6223 or 954 585 6223 to obtain a Repair Authorization RA number and The image on the Change the camera position provide the following information screen flickers gt Check that the DC
22. t Sync Select L L or INT using the Reset LEFT or RIGHT button End Press SET button p gt Phase 45 ee Press SET to Return Adjust the Phase level using the LEFT or RIGHT button from 0 to 270 When the power frequency is 60Hz you can use linelock mode NTSC models When the power frequency is 50Hz you can use linelock mode PAL models B Day amp Night Color CCD Camera CAM91 2005 10 13 10 45 PM 4 34 b m Operating Your Camera m Using Remote Jack o Reset Remote Control on Setup This function resets the camera to the default setting preset at the factory If you connect a remote plug to the REMOTE jack on the rear on the camera as 1 Press the SET button to display the Setup menu and move the arrow indicator shown below you can access the menu setup mode from a remote place with an to Reset using the UP or DOWN button equipment like computer Setup oo 1 RS 232C Communication Setting Lens Mode Serial Data bit 8 Shutter Bit sec 9600bps Stop bit 1 Gain RN White Balance Parity None Motion Detect Color 2 Wiring Syne REMOTE gt Reset End Press SET button p Are you sure Select YES or NO using the LEFT GND Grounding Terminal or RIGHT button Tx Transmit Data Rx Receive Data 2 In the confirmation mode select YES or NO If YES selected all modes are initialized and return to the default status 3 Setup
23. tic mode changeover by sensing day or night Contact an authorized technician for inspection conditions It can change color mode in the day condition for optimal color and BW mode in night condition for clear identification 2 Stop using your camera when you find a malfunction If you use your camera around smoke or unusual heat for a long time a fire may High Resolution be caused The horizontal resolution of 480TV lines at color mode and 520TV lines at BW mode can be achieved by using a high density Sony CCD 410K pixels which 3 Do not install the camera on a surface that can not support it provides clean noiseless and reliable pictures Unless the surface is suitable it could cause falling or other hazards e Motion Detection 4 Do not hold plug with wet hands The camera transmits an alert signal to the REMOTE jack when it detects It could cause an electric shock motion of an object If you connect an optional alarm to the camera you can get the effective surveillance This allows multi observation through several 5 Do not disassemble the camera monitors efficiently It may result in fire electric shock or other hazards Controlled by OSD menu and RS 232C You can control the camera using OSD menu and RS 232 jack at a remote place Video DC Lens Selectable The camera accepts 2 types of auto iris lens DC type VIDEO type and is set with the DC VIDEO selection switch 6 Do not use the camera
Download Pdf Manuals
Related Search