M-Systems Flash Disk Pioneers 48-SR-003-03-7L User's Manual
Contents
1. including personnel and equipment grounding Before you begin installing the IDE Plus inspect the package and device as follows e If the shipping container appears to be damaged or water stained notify your dealer e Remove the disk from its shipping enclosure and inspect it for any damage that may have occurred during shipment If any damage is observed notify your dealer e Record the disk serial number and shipment date e Retain the original shipping enclosure and all packing material for re shipment 4 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV a M Systems eum Flash Disk Pioneers 4 HANDLING INSTRUCTIONS You can prolong the life of your IDE Plus increase its reliability and prevent unnecessary damage by following the instructions listed below Failure to follow any of these instructions may void your warranty e Always take all proper electrostatic discharge ESD precautions including personnel and equipment grounding e Always operate the IDE Plus within the environmental specifications e Always use a grounded wrist strap when handling the IDE Plus Drives that are not installed in the system are sensitive to ESD damage e Always handle the IDE Plus carefully e Never switch DC power to the drive by plugging an electrically live source cable into the drive s power connector e Pay attention to the cable polarity whenever connecting the drive to the cable 5 FFD 2 5 and 32. 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 77E M Systems mm Flash Disk Pioneers 5 FFD IDE PLUS DRIVE CONFIGURATION 5 1 Master and Slave Jumper Settings 9 1 1 FFD 2 5 IDE Plus Prior to mounting the drive in the system drive bay the FFD 2 5 IDE Plus must be configured according to Figure land Figure 2 Master blave Cable select m fE rhi 50 L 50 a Figure 1 FFD 2 5 IDE Plus Address Setting by Jumper Figure 2 FFD 2 5 IDE Plus Slave Setting by Jumper 6 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 n7 E M Systems mm Flash Disk Pioneers 5 1 2 FFD 3 5 IDE Plus Prior to mounting the drive in the system drive bay the FFD 3 5 IDE Plus must be configured according to Figure 3 1 IGECS P4 Ps P2 Pl Slave Master Master with Slave present CSEL e Activity LED amp Activity LED Reserved amp Figure 3 FFD 3 5 IDE Plus Jumper Settings T FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 77E M Systems mm Flash Disk Pioneers 5 2 Write Protect Jumper Settings The FFD IDE Plus has a write protect option that is controlled by the jumper settings 5 2 1 FFD 2 5 IDE Plus Figure 4 illustrates the jumper configuration for the write protect option for the FFD 2 5 IDE Plus hieste Slave Cable Select 4 write protect Write protect Cable Select write protect aa 27 Boy s
3. 77 E M Systems am Flash yS Pioneers FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual January 2004 48 SR 003 03 7L Rev 2 1 VV 8 M Systems emus Flash Disk Pioneers DOCUMENT CONTROL INFORMATION Issued by Assistant Vice President Rugged Market October 12 2003 Updated by DiskOnChip Rugged Product Manager January 7 2004 2 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 7 E M Systems am Flash Disk Pioneers TABLE OF CONTENTS a A N 7 8 9 How to Contact Us C21 9 2 it Rene nee eee ee en ee en eee ee ee ere KICCONTENIS arino aa Visual NSPE tl ONM iniiianciic enice aaau aridis Handling Instructions a sassssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnne FFD IDE Plus Drive Configuration c ccccsssessseseeeeeeeeeeeees 5 1 Master and Slave Jumper Settings cccccceececeeeee eens Zbl FED ZO IDE PFlUS neredir are a A gl FFEV S DE RUS aa E 5 2 Write Protect Jumper Settings cccccceccseeceeeeeeeeeeeeeees co Yd FFD 2o IDE PIOS eee eee ee ae ee Re e 32A FED 0 IDE PlU wieiedec samosas tees dis A 5 9 Interlace CONMECIONS vei scciteciciditiietledacivnssenberds EN 2091 PFZ IDE PIOS ieceaiecacuncten Satins tecamieanie iemmactcaoiaiasede stuns 292 FFD 3o IDE PIUS eee ee een eer ec eee OA IDE CAD le aire cscs ttateccieia A tae installalo Nanana 6 1 System RequireMent cccccccccesceceeeceeeeceeeeeeeeeeeeseeeeees 62 FED
4. IDE Plus COnNNgUratON ze issis chealeiats 69 FFDIDE PIUSANStAIGLIOM e 6 3 1 Installing the FFD IDE Plus in a PC Environment 6 3 2 Using the FFD IDE Plus in an MS DOS Based Platform Driv ParaimeGlers sncsnions orraa a aa tan Troubleshooting eri ceninaes is bapncenddenanaldeneceunern cece sbernst HOW LO Ob FIG Darran FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV 8 M Systems emus Flash Disk Pioneers 1 GENERAL This manual provides you with the information you need to properly install your new FFD 2 5 or 3 5 IDE Plus Flash Disk M Systems recommends that qualified and trained personnel install the drive The following chapters contain handling information mounting considerations address and configuration setups cabling and connector information and information about obtaining technical assistance and service Remember Always back up your data before adding disk drives to your system 2 KIT CONTENTS Ensure that your kit contains the following items For 2 5 version e FFD 2 5 IDE Plus Flash Disk e Four mounting screws and two jumpers M Systems part no 48 PK 008 00 For 3 5 version e FFD 3 5 IDE Plus Flash Disk e Four mounting screws and two jumpers M Systems part no 48 PK 016 00 If any items are missing please contact your dealer 3 VISUAL INSPECTION Before unpacking or handling a drive take all proper electrostatic discharge ESD precautions
5. ect the total number of sectors in the IDE Plus using the IDENTIFY DRIVE command and configure them accordingly However some older device drivers need to obtain the drive geometry parameters manually The physical drive parameters are just a convention and have no effect on the way data is stored within the IDE Plus Table 1 Drive Parameters Unformatted Total Number of Number of Number of Number of Current CHS Disk Capacity User Addressable Logical Sectors Logical Heads Logical Cylinders Capacity Sectors in LBA per Track Words 3 and 55 Words 1 and 54 after Sectors Mode Words 6 and 56 after power on of power on of IDENTIFY Words 57 58 after Words 60 61 of after power on of IDENTIFY information power on of IDENTIFY information IDENTIFY pronation IDENTIFY information information 13 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV E M Systems mm Flash Disk Pioneers Unformatted Total Number of Number of Number of Number of Current CHS Disk Capacity User Addressable Logical Sectors Logical Heads Logical Cylinders Capacity Sectors in LBA per Track Words 3 and 55 Words 1 and 54 after Sectors Mode Words 6 and 56 after power on of power on of IDENTIFY Words 57 58 after Words 60 61 of after power on of IDENTIFY information power on of IDENTIFY information IDENTIFY Intron IDENTIFY information information 34816 68434944 16383 16514064 14 FFD 2 5 a
6. ge 15 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 77 E M Systems mm Flash Disk Pioneers HOW TO CONTACT US USA M Systems Inc 8371 Central Ave Suite A Newark CA 94560 Phone 1 510 494 2090 Fax 1 510 494 5545 Japan M Systems Japan Inc Asahi Seimei Gotanda Bldg 3F 5 25 16 Higashi Gotanda Shinagawa ku Tokyo 141 0022 Phone 81 3 5423 8101 Fax 81 3 5423 8102 Taiwan M Systems Asia Ltd Room B 13 F No 133 Sec 3 Min Sheng East Road Taipei Taiwan R O C Tel 886 2 8770 6226 Fax 886 2 8770 6295 China M Systems China Ltd Room 121 122 Bldg 2 International Commerce amp Exhibition Ctr Hong Hua Rd Futian Free Trade Zone Shenzhen China Phone 86 755 8348 5218 Fax 86 755 8348 5418 Europe M Systems Ltd 7 Atir Yeda St Kfar Saba 44425 Israel Tel 972 9 764 5000 Fax 972 3 548 8666 Internet http www m sys com General Information info m sys com Sales and Technical Information techsupport m sys com This document is for information use only and is subject to change without prior notice M Systems Flash Disk Pioneers Ltd assumes no responsibility for any errors that may appear in this document No part of this document may be reproduced transmitted transcribed stored in a retrievable manner or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or ot
7. herwise without prior written consent of M Systems M Systems products are not warranted to operate without failure Accordingly in any use of the Product in life support systems or other applications where failure could cause injury or loss of life the Product should only be incorporated in systems designed with appropriate and sufficient redundancy or backup features Contact your local M Systems sales office or distributor or visit our website at www m sys com to obtain the latest specifications before placing your order 2004 M Systems Flash Disk Pioneers Ltd All rights reserved M Systems DiskOnChip DiskOnChip Millennium DiskOnKey DiskOnKey MyKey FFD Fly By 1DiskOnChip 1DOC mDiskOnChip mDOC Mobile DiskOnChip Smart DiskOnKey SuperMAP TrueFFS uDiskOnChip and uDOC are trademarks or registered trademarks of M Systems Flash Disk Pioneers Ltd Other product names or service marks mentioned herein may be trademarks or registered trademarks of their respective owners and are hereby acknowledged All specifications are subject to change without prior notice 16 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1
8. ion 6 2 3 Connect a cable between the IDE Plus and the host Make sure to orient the cable so that pin of the IDE Plus is connected to pin 1 of the host adapter 4 Mount the IDE Plus into a free drive bay Close the PC cover and power on the PC 6 The host BIOS sign on message will appear and display a key sequence to enter the BIOS setup Set up the BIOS to recognize the IDE Plus refer to the BIOS documentation for the disk installation procedure You are now ready to use the IDE Plus If you encounter any problems refer to Section 8 for troubleshooting information 6 3 2 Using the FFD IDE Plus in an MS DOS Based Platform After installing the IDE Plus as described in Section 6 3 it must be installed as a disk drive under DOS Run the DOS commands listed below and follow the instructions displayed for each command For more information regarding the DOS commands refer to your DOS manual 11 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV 8 M Systems eum Flash Disk Pioneers Run the DOS FDISK program to partition the IDE Plus Run the DOS FORMAT command to high level format the IDE Plus If you want the IDE Plus to be a bootable drive run the DOS SYS command and change its partition to active D gt 12 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV a M Systems eum Flash Disk Pioneers l DRIVE PARAMETERS Most IDE device drivers can automatically det
9. is recommended that the mating connector be blocked at pin 27 using a special plastic key the key can be ordered from the connector manufacturer This prevents possible damage to the disk by connecting the cable with a 180 rotation 5 4 IDE Cable The cable length should not exceed 18 inches 10 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV 8 M Systems emus Flash Disk Pioneers 6 INSTALLATION 6 1 System Requirements In order to install the IDE Plus in your system ensure that you have the following items e System mounting hardware e 44 pin ribbon IDE cable for FFD 2 5 IDE Plus or 40 pin cable for FFD 3 5 IDE Plus 6 2 FFD IDE Plus Configuration Before mounting the drive into the system drive bay you must first configure the IDE Plus by setting the address jumper to comply with your system requirements See Section 5 for details 6 3 FFD IDE Plus Installation The IDE Plus can be installed in the system in any mounting position Unlike rotating disks that have an axis of rotation the IDE Plus is not susceptible to damage due to its orientation Note It is not necessary to perform a low level format on the IDE Plus The drive is shipped low level formatted and ready for use 6 3 1 Installing the FFD IDE Plus in a PC Environment To install the IDE Plus 1 Power down the PC and remove the cover 2 Configure the IDE Plus jumper settings according to the information provided in Sect
10. nd 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV a M Systems eum Flash Disk Pioneers 8 TROUBLESHOOTING The problems that arise in most installations are summarized below e Cables o Homemade short flat ribbon cables with bad contacts or cheap cables o Mixing round cables with flat cables e Cable Length o Exceeds the limit specified in the standard o Cables are too long to support the transfer rate e Device Address Conflict o Adding anew device with an IDE setting identical to an existing device on the bus o Connection o Connecting a cable in reverse polarity 9 HOw TO GET HELP If you need technical assistance with the installation and or configuration of your IDE Plus contact one of the sources listed on the contact page Before you call please be sure to have the following information available for the customer support representative e Product and serial number of your IDE Plus e Description of computer hardware manufacturer model attached devices etc e Description of your IDE host adapter and associated drivers e Description of your software operating system version application software etc e Acomplete description of the problem e The exact wording of any error messages Before contacting M Systems directly first contact your dealer If your dealer cannot provide the help you need you can obtain technical support directly from M Systems at one of the numbers listed on the contact pa
11. q Figure 4 FFD 2 5 IDE Plus Write Protect Jumper Settings 8 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 77E M Systems gums Flash Disk Pioneers 9 2 2 FFD 3 5 IDE Plus Figure 5 illustrates the jumper configuration for the write protect option for the FFD 3 5 IDE Plus CSEL Write Protect Master Write Protect Slave Write Protect e Activity LED amp Activity LED Figure 5 FFD3 5 IDE Plus Write Protect Jumper Settings 9 FFD 2 5 and 3 5 IDE Plus Flash Disk User Manual 48 SR 003 03 7L Rev 2 1 VV 8 M Systems eum Flash Disk Pioneers 5 3 Interface Connectors 9 3 1 FFD 2 5 IDE Plus The FFD 2 5 IDE Plus has a 2 00 mm pitch interface connector located on the rear panel The DC power and IDE bus are input through a non shielded 50 pin flat cable 2 00mm L Umm Tak N Na Figure 6 FFD 2 5 IDE Plus Interface Connector It is recommended that the mating connector be blocked at pin 27 using a special plastic key the key can be ordered from the connector manufacturer This prevents possible damage to the disk by connecting the cable with a 180 rotation 5 3 2 FFD 3 5 IDE Plus The FFD 3 5 IDE Plus should be connected using a 40 pin I O cable connector with a 2 54 mm pitch interface connector As with the FFD 2 5 IDE Plus it
Download Pdf Manuals
Related Search