Lux Products T10-1143 (discontinued) Instruction Manual
Contents
1. SCREWS SCREWS HOLES FOR WIRES FIGURE 3 FIGURE 4 SUB BASE DECORATIVE WALL PLATE WRONG RIGHT WHEN ADJUSTING THE SETTING ON THE HEAT ANTICIPATOR GRASP THE ROUND BOARD NOT THE LEVER AND GENTLY ROTATE THE LONG POINTER If you have any problems install ing or using this thermostat please read the instructions Carefully Technical Service is available through our Technical Service number If you require assistance please call our offices between 8 00 a d 4 30 p m Eastern Standard Time Monday through Fi The number is 856 234 883 WARRANTY Limited Warranty If this unit fails because of defects in materials ot workmanship within one year of date of original purchase Lux will at its option repair or replace it This warranty does not cover damage by accident misuse or failure to follow installation instructions Implied warranties are limited in duration to one year from date of original purchase Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Please return malfunctioning or defective units to the participating retailer from which purchase was made along with proof of purchase Please refer to Technical Service Section before returning thermostat Purchaser assumes all risks and liability for incidental and consequential damage resulting from installation and use of this unit Some states do not allow the exclu2. INSTALLATION AND OPERATING INSTRUCTIONS f FAN RELAY FAN RELAY COOLING COMPRESSOR COOLING COMPRESSOR HEATING CONTROL HEATING CONTROL HEATING TRANSFORMER HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE DAMPER OR CHANGEOVER VALVE POWERED m HEAT POWERED IN HEAT DAMPER OR CHANGEOVER VALVE Poweneo w coou Pi G Y WRH BO RC 140 1143 DELUXE HEATING amp COOLING THERMOSTAT 2 SS tape off wire R connect wire B SPECIFICATION Ema if replacing a Honeywell thermostat with a clock wire C tape off wire C ELECTRICAL RATING 24 Vac 30 Vac Maximum If both Y and C wire are present tape off C wire SUITOH ACTION gt Sealed Mercury Switch Meatia x of te Meester ANTICIPATOR RATING HEATING soscsessesensesenstntneesen 0 15A to 1 24 irion Se gts odet COOLING Fixed 24 VAC EATING CONTROL HEATING CONTROL TEMPERATURE RANGE 50 F to 90 F a e A T arenon ene ae DAMPER OR CHANGEOVER VALVE DAMPER OR CHANGEOVER VALVE owen w coou poweneo m coou INSTALLATION amp OPERATIO 1 THERMOSTAT LOCATION For accurate temperature control and comfort correct location is very important On new installations the guidelines listed below should be followed as closely as possible When replacing an old thermostat install the new one in the same location unless these conditions copt transronmen Y W RH B O RC Opt
3. inal screws shown in Figure 2 Make sure bare metal wires do not touch each other Push all excess wire back into wall ow W hi Cases O Place Base Figure 3 over Sub Base and attach by tightening three captive screws O Fasten loosely to wall using two mounting screws Place a level against the bottom of the Base adjust until it is level and then tighten mounting screws to secure O Find anticipator setting on old thermostat Setting on new thermostat should be the same Do this by carefully sliding the long pointer Figure 2 over desired number printed on the anticipator If old anticipator setting cannot be determined look on gas control on furnace or set at at 6 During heating season furnace should operate about five times an hour If adjustments are necessary move heat anticipator pointer slightly and recheck NOTE Set pointer to 1 2 for millivolt systems O Attach front cover Figure 1 to base C Turn electricity and gas back on and set pointer on top of thermostat to desired temperature C FOR HEATING Set slide switch to Heat Set fan switch to Auto O FOR COOLING Set slide switch to Cool Set fan switch to Auto O FAN For continuous blower operation set switch to ON For automatic blower operation set fan switch to Auto Thermostat will then cycle the blower on anf off CAPTIVE SCREWS MOUNTING HOLES ANTICIPATOR LONG POINTER CAPTIVE
4. ional Optional suggest otherwise 1 Locate the thermostat on an inside wall about five feet above the floor where it is easy H both Y and C wire are If both Y and C wire are to install and adjust It should be in a room that is used often such as a family room present tape off C wire present tape off C wire 2 Do not install it where there are unusual heating conditions such as direct sunlight close to a lamp radio television radiator register near a fireplace or other heat producing appliance Also check for hot water pipes within the wall or a stove on the other side of the wall belov r ti ru 3 Do not locate in unusual cooling conditions such as on an outside wall or one separating PIN RIN a SS an unheated room or in drafts from stairwells doors or windows n n See it i i if j y y AL COOLING AND 4 Do not locate in a damp or humid area This can shorten thermostat life due to corrosion rae vata N TO AOR EON A enna Seaton 5 Do not locate where air circulation is poor such as in a corner alcove or behind an MILLIVOLT SYSTEM WIRE IS F AN WIRE 4 WIRE open door G Y WRHB O RC G Y WRHB O RC 6 Do not install until all construction work and painting have been completed 2 TOOLS REQUIRED Wirestripper or knife drill with 16 bit screwdriver level and a pencil 3 REMOVING OLD THERMOSTAT Please read all instructions carefully As you complete each step check the adjoining squa
5. re Z O Disconnect electricity and turn off gas to the heater O Remove cover from old thermostat O Disconnect wires from thermostat making sure they do not fall back inside the wall Make TYPICAL COOLING AND TREAT PUMP WIRING note of wires and to which terminals they are attached as you disconnect them For Oona G Y WRHB O RC example Yellow wire to terminal Y Red wire to terminal RH etc O Strip insulation Ys from wire ends and clean off any corrosion O Loosen all screws on the old thermostat and remove it from the wall O Fill wall opening with non combustible insulation to prevent drafts from affecting thermostat 4 INSTALLING NEW THERMOSTAT U Place new decorative wall plate if supplied Figure 4 over wall opening Decorative wall plate can optionally be left off C Remove Front Cover of new thermostat by inserting a finger in the side of the thermostat and gently prying away each corner Remove Base Figure 2 from Sub Base Figure 3 by loosening three captive screws O Place Sub Base Figure 3 on wallplate over wall opening Mark wall with pencil at mounting holes as shown in Figure 2 Now lay wallplate and Sub Base to the side O Drill two holes with Ye bit 1 deep O Insert plastic screw anchors into drilled holes flush with wall surface O Bring wires through large hole in decorative wall plate and through Hole For Wires in Sub Base O Referring to your notes and the following diagrams attach wires to term
6. sion of incidental or consequential damages so the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Applicable in the U S A only RECYCLING f one This Thermostat contains mercury in a sealed glass vial De NOT dispose of this Thermostat in the trash Neither this thermostat nor any existing mercury thermostat this unit replaces Should be disposed of in the trash Contact your local waste management authority for proper disposal instructions for mercury in a sealed glass tube If you have any questions please call 856 234 8803 PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE LUX PRODUCTS CORAPRATION Mt Laurel New Jersey 08054 USA
Download Pdf Manuals
Related Search