Lund Industries AT-500 User's Manual
Contents
1. Nissan Truck 1986 and later Nissan 4 x 4 Truck 1990 and later Nissan Pathfinder 1993 and tater Nissan Altima 1994 and later Nissan Sentra MAZDA All Models VOLKSWAGEN All Models AT SO0 PMGS 91012. black wire to the negative post of the battery STEP 5 Connect the red wire to a switch that has a 12 volt fused source connected to it PASSENGER SIDE HIGH BEAM ORIVER SIDE HIGH 8EAM CUT HIGH BEAM WIRE w ioe w Zz amp lt z Q z og GREEN OR BLACK TO 12V SWITCHED TO NEGATIVE TERMINAL OF BATTERY Wiring Diagram STEP 6 Cut the high beam wires less than 12 inches from the passen ger side headlight Attach the yellow wire to the high beam wire that goes directly to the headlight STEP 7 Attach the blue wire to the wire that was originally connected to the passenger side high beam STEP 8 Test the Flasher and headlight operation WARRANTY Lund Industries Inc warranties the AT 500 Electronic Flasher System for one 1 full year from the date of purchase to the original purchaser against any manufactured defects or work manship This warranty applies only to units installed accord ing to manufacturer s installation instructions and operated within the units specifications Warranty is void if the unit was installed incorrectly or maliciously damaged All warranty claims must be accompanied by a dated proof of purchase Lund Industries Inc retains the right to be the sole mediator of what constitutes defects in performance or manufacturing Covered under U S Patents 4114071 and 4309639 SPECIALISTS IN EMERGENCY VEHICLE PRODUCTS SINCE 1978 DESIGN MANUFACTURING DISTRIBUTION
3. AND INSTALLATION COMPATIBLE VEHICLE LIST ACURA Acura Integra 1989 and later Acura Legend DODGE 1986 and later Dodge D50 Truck 1999 and later Dodge Durango EAGLE 1990 and later Eagle Talon GEO 1991 Geo Metro 1992 and later Geo Prizm 1992 and later Geo Storm 1992 and later Geo Tracker HONDA 1991 and later Honda Prelude and Accord HYUNDAI 1988 and later Hyundai SL GL 1990 and later Hyundai ISUZU 1991 and later Isuzu Truck 1994 and later Isuzu Trooper LEXUS 1992 and later Lexus LS400 MITSUBISHI 1990 and later Mitsubishi Montero 1993 and later Mitsubishi Eclipse SATURN 1991 1992 Saturn Sedan SUZUKI 1991 and later Suzuki Swift TOYOTA Toyota T100 Full Size 1986 and later Toyota Truck 1986 and later Toyota Tercel 1986 and later Toyota 4 x 4 Truck 1987 and later Toyota Corolla This is not a complete list but rather a comprehensive list of vehicles Lund Industries Inc knows to have Ground Side Switching Headlights If you are unsure about your vehicle obtain a copy of your headlight schematic from your dealer and FAX a copy to Lund Industries Inc attn Technical De partment and someone will assist you NON COMPATIBLE VEHICLE LIST The AT 500 WILL NOT work on the following vehicles These vehicles have Hot Side Switching Headlights and the AT 300 Flasher should be used instead HONDA 1982 and later Honda Civic and Civic LX 1985 and later Honda Accord NISSAN 1984 and later
4. WWwW LUND INDUSTRIES COM S Rev 6 05 303 MESSNER DR WHEELING IL 60090 847 459 1460 FAX 847 459 1569 AT 500 Alternating Flasher For Vehicles With Ground Side Switching Headlights itis important to read understand and follow all instructions shipped with this product Failure to follow all safety precau tions and instructions may result in serious injury or death to you or to others NOTE With most foreign vehicles the low beam headlights must be turned ON before the headlight flasher will operate This needs to be done because of the design of the headlight wiring INSTALLATION NOTE Please refer to the Compatible Non Compatible Vehicle Lists before attempting installation STEP 1 Mount the Flasher near the passenger side headlight STEP 2 With the headlights in the OFF position measure the voltage on all 3 wires going into the driver side headlight If all the wires have voltage on them itis not required to turn the head lights ON for the Flasher to operate STEP 3 Turn the headlights ON in the high beam position Measure the voltage on all 3 wires going into the passenger side head light The wire with no voltage on it is the high beam wire This wire is where the Flasher wires need to be installed NOTE If only one of the three wires has voltage on it when the high beams are ON this Flasher WILL NOT work on your vehicle Contact Lund Industries Inc for assistance STEP 4 Connect the
Download Pdf Manuals
Related Search