Lumiscope 1100 User's Manual
Contents
1. If the downward arrow W flashes there is air remaining in the cuff Release it by pressing the Air Release Valve until 0 appears on display at at oo The unit is ready for measurement at this point N Pump the bulb to increase pressure in the arm cuff The display will show the pressure reading within the cuff Continue pumping until the pressure reaches approximately 50 60 mmHg above your normal systolic pressure Three short beeps will be heard if you pump the pressure to 170 mmHg to remind you to stop THA If the cuff pressure is not enough an upward arrow 4 will display and two short beeps will be heard to remind you that you should continue pumping 3 Sit still and wait for the monitor to deflate and measure your blood pressure It is important to remain still and quiet during measurement Any significant movement may affect measurement results 4 Upon completion of the measurement cycle the monitor will display systolic diastolic and pulse readings and the unit will make a long beep Measurement is now complete and the reading is automatically stored in the monitor The display will indicate a downward arrow W Keep pressing the air release valve above the bulb until all pressure in cuff is released 5 Press the POWER button to turn off the power If no button is pressed the unit will shut off automatically in approximately one minute K o Recalling Memory 12. Systolic gt 160 Stage 2 Hypertension Sa ioe 100 90 Stage 1 Hypertension als ee n g i Systolic 120 139 5 80 Prehypertension Diastolic 80 89 8 Systolic 90 119 S 50 Normal Diastolic 50 79 Hypotension Systolic lt 89 Diastolic lt 49 90 120 140 160 Systolic mmHg gt Blood Pressure Fluctuation mmHg PFEP 200 m Fluctuation within a day Blood pressure fluctuates all the time You Case Male 35 years old should not be overly worried if you encounter two or three measurements at high levels Blood 150 pressure changes over the month and even throughout the day It is also influenced by Systolic pressure season and temperature 100 H Diastolic pressure Wake Arrive ered Argument Leave Dinner 50 up office telephone aeris office Sleep ne io 18 00 A0 Display Explanation Display Icons hl ia A ere when manual cuff inflation is L L Appears when manual cuff deflation is rm x needed Diastolic Pressure j j E gt Appears when batteries should be lt m replaced rr O TUT pulse Rate U DE QP Shows the pulse rate per minute No of Memory Sequence Occurs when a mistake was made during measurement Installing Battery 1 Press down and lift the battery cover in the direction of the arrow to open the battery compartment 2 Install or replace 2 AA sized batteries in the battery compartment according to the indications inside the c
3. anything inside the device If you have any problems please contact the store or the doctor from whom you purchased your Lumiscope Blood Pressure Monitor 7 For users diagnosed with common arrhythmia atrial or ventricular premature beats or atrial fibrillation diabetes poor circulation of blood kidney problems or for users who have suffered a stroke the device might not be suitable for use 8 Do not use on unconcious patients Specifications Measurement Method Oscillometric Measurement Range Pressure 20 280mmHg Pulse 40 180 beats min Pressure Sensor Semi conductor Accuracy Pressure 3mmHg Pulse 5 of reading Inflation Manual Inflation Deflation Automatic Pressure Release Valve Memory capacity 60 memories Auto shut off 1 minute after last button operation Operating Environment Temperature 5 C 45 C 41 F 113 F Humidity 40 85 Storage Environment Temperature 10 C 60 C 14 F 140 F Humidity 10 95 Power Source 3V DC two AA Batteries Dimensions gt 115 L X 94 5 W X 60 5 H mm Weight 320 g G W No Batteries Arm circumference Adult 24 36 cm 9 4 14 2 standard Specifications are subject to change without notice Two Year Limited Warranty Lumiscope guarantees this product free from defects in material and workmanship for a period of two years from the date of purchase except as noted below This Lumiscope product warranty d
4. physician Please be sure to keep this manual Name Function of Each Part LCD Display Memory Recall Button Arm Cuff Power Button Battery Compartment Air Release Valve About Blood Pressure What is Blood Pressure Blood pressure is the pressure exerted on the artery tube while blood flows through the arteries The pressure measured when the heart contracts and sends blood out of the heart is systolic highest The pressure measured when the heart dilates with blood flowing back into the heart is called diastolic lowest blood pressure Why Measure Your Blood Pressure Among the various health problems afflicting modern people problems associated with high blood pressure are by far the most common High blood pressure s dangerously strong correlation with cardiovascular disease has made measuring blood pressure a necessity for identifying those at risk Blood Pressure Standard The World Health Organization WHO and National High Blood Pressure Education Program Coordinating Committee have developed a blood pressure standard according to which areas of low and high risk blood pressure are identified This standard however is a general guideline and blood pressures vary between different people age groups etc It is important that you consult with your physician regularly Your physician will tell you your normal blood pressure range as well as the point at which you will be considered at risk
5. LUMISCOPE SEMI AUTOMATIC UPPER ARM Blood Pressure Monitor Model 1100 Features e Semi Automatic e Easy to read Display e 60 Automatic Memories e Beeping Reminder Table of Contents Introduction ssssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 2 Applying the Cuff 0 sccccsccssssssssseeees Name Function of Each Part 2 Taking a Measurement ccssscssssseee0s Preliminary Remarks 0000000s0000 3 Recalling Memory scccsccsssssssssesees About Blood Pressure cccscssssssssss 3 VHelptulilipS cccseccsececascscnccecescescreeecscesese Blood Pressure Standard 2 000 3 Troubleshooting 0cccccsscsssssssssseeees Blood Pressure Fluctuation 4 Cautionary Notes ccsssccsssscees Display Explanations 0 0000s0000 4 Specifications sssseessseeseeseees Installing Batteries sssssssses 4 Introduction Blood pressure measurements determined with your Lumiscope Blood Pressure Monitor are equivalent to those obtained by a trained observer using cuff stethoscope auscultation method within the limits prescribed by the American National Standard Electronic or Automated Sphygmomanometers This monitor is to be used by adult consumers in a home environment Attention Consult the accompanying documents e Please read this manual carefully before use for specific information on your own blood pressure contact your
6. To recall stored blood pressure readings from memory simply press the Memory button The last set of memorized readings will be displayed 2 Another press of the Memory button will recall the previous set of readings 3 All readings stored in memory will be displayed with its sequence number Helpful Tips h Onan mem En Y ma mem og u m a Tan Here are a few helpful tips to help you obtain more accurate readings e Do not measure your blood pressure immediately after consuming a large meal To obtain more accurate readings please wait one hour before measuring e Do not smoke or drink alcohol before measuring your blood pressure e You should not be physically tired or exhausted while taking a measurement e t is important that you relax during measurement Take a 15 minute rest before a reading e Do not take measurements if you are under stress or under tension e Take your blood pressure at normal body temperature If you are feeling cold or hot wait a while before taking a measurement e f the monitor is stored at very low temperature near freezing have it placed at a warm location for at least one hour before using it e Wait about 5 minutes before taking the next pressure measurement If any abnormality should arise during use please check the following points Troubleshooting Symptom Check Point Correction No display when the Have the batteries run down Replace with two new batteri
7. es POWER button is pressed Have the batteries polarities been positioned incorrectly Re insert the batteries in the correct positions EE mark shown on display or the blood pressure value is displayed excessively low high Is the cuff placed correctly Wrap the cuff properly so that it is positioned correctly Is the cuff pressure pumped enough 50 60 mmHg above normal systolic value Measure it again and pump up 50 60 mmHg more than normal systolic value Did you talk or move during measurement Did you shake the arm with the cuff on Measure it again quietly Cautionary Notes 1 The unit contains high precision assemblies Therefore avoid extreme temperatures humidity and direct sunlight Avoid dropping or strongly shocking the main unit and protect it from dust 2 Clean the blood pressure monitor body and the cuff carefully with a slightly damp soft cloth Do not iron wash or use chemical cleaner on the cuff Never use thinner alcohol or petrol gasoline as cleaner 3 Leaky batteries can damage the unit Remove the batteries when the unit will not used for a long period of time 4 The unit should not be operated by children 5 If the unit is stored near freezing allow it to acclimate at room temperature before use 6 Your Lumiscope Blood Pressure Monitor is not field serviceable You should not use any tool to open the device nor should you attempt to adjust
8. oes not cover damage caused by misuse or abuse the attachment of any unauthorized accessory alteration to the product or any other conditions whatsoever that are beyond the control of Lumiscope Lumiscope shall not be responsible for any type of incidental consequential or special damage All implied warranties including but not limited to those implied warranties of fitness and merchantability are limited to the total duration of two years from the original date of purchase To obtain warranty service on your Lumiscope Blood Pressure Monitor please contact the Lumiscope Repair Department at 1 800 672 8293 or visit www lumiscope net There is a 15 fee for return shipping and handling Please make checks payable to The Lumiscope Co Inc Upon receipt Lumiscope will repair or replace as appropriate this blood pressure monitor and return it to you Warranty is solely through the Lumiscope Repair Department Service of this product by anyone other than the Lumiscope Repair Department voids warranty In the event that Lumiscope does not abide by the terms of this warranty the consumer may seek breach of contract remedies in the New York State Federal courts of law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you Distributed By The Lumisco
9. ompartment 3 Replace the battery cover by clicking in the bottom hooks first then push in the top end of the battery door You need to replace the batteries when 1 The low battery icon appears on display 2 The POWER button is pushed and nothing X appears on display A lying the arm cuff 1 Plug in the cuff connecting tube to the unit 2 Unwrap the arm cuff leaving the Index end of the cuff through the D ring of the cuff 3 Put your left arm through the cuff loop The OK range indication should be positioned closer to yourself with the rubber tube pointing in the direction of your arm Position the artery mark over the main artery on the inside of your arm in the upper arm N Main Artery 2 3 cm 4 Turn your left palm upward and place the edge 08 1 2 o If the Index line falls within the OK range of the arm cuff at approximately 2 to 3 cm above the inner side of the elbow joint Tighten the cuff by pulling the Index end of the cuff indicated at the edge of the cuff this cuff is suitable for your use If the Index line falls out of the OK range you may need a special cuff for measurement Please visit www lumiscope net or contact our service department at 1 800 672 8293 for more information regarding additional cuffs Taking a Measurement 1 Press the POWER button All displays will appear for approximately one second before returning to 0
10. pe Co Inc www lumiscope net Repair Department 1 800 672 8293 Made and Printed in China
Download Pdf Manuals
Related Search